display INFINITI M35 2007 Factory Service Manual

GW-106
REVERSE INTERLOCK DOOR MIRROR SYSTEM
Revision: 2007 April2007 M35/M45
Display Item List
Work Flow NIS00239
1. Check the symptom and customer's requests.
2. Understand the system description. Refer to GW-94, "
System Description" .
3. According to the trouble diagnosis chart, repair or replace the cause of the malfunction. Refer to GW-106,
"Symptom Chart"
4. Does reverse interlock door mirror system operate normally?
Yes , GO TO 5.
No, GO TO 3.
5. INSPECTION END
Symptom ChartNIS0023A
Test item Description
MIRROR MOTOR RHThe RH mirror motor moves the mirror UP/DOWN and LEFT/RIGHT by receiving the drive
signal.
MIRROR MOTOR LHThe LH mirror motor moves the mirror UP/DOWN and LEFT/RIGHT by receiving the drive
signal.
Symptom Diagnoses / service procedureReference
page
Reverse interlock door mirror does not operate.1. Check seat set switch circuitSE-81
2. Check changeover switch circuitGW-107
3. Check mirror switch circuitGW-109
4. Check A/T control device R position signal circuitGW-117
5. Check mirror motor circuitG W - 111
6. Check mirror sensor circuitGW-114
7. Replace automatic drive positioner control unitSE-11

At reverse interlock door mirror system operation, mirror
angle is not in the setting position

After finishing the reverse interlock door mirror system.
Operation, mirror angle does not return to the original posi-
tion1. Check mirror sensor circuitGW-1142. Check A/T control device R position signal circuitGW-117
3. Replace automatic drive positioner control unitSE-11
None of the door mirror can be operated using mirror switch. Check mirror switch circuitGW-109
A part of the remote control door mirror does not operated.1. Check mirror switch circuitGW-1092. Check door mirror circuitGW-109
Mirror remote control switch can not be switched right and left.1. Check changeover switch circuitGW-1072. Check mirror switch circuitGW-109

REVERSE INTERLOCK DOOR MIRROR SYSTEM
GW-107
C
D
E
F
G
H
J
K
L
MA
B
GW
Revision: 2007 April2007 M35/M45
Check Changeover Switch CircuitNIS0023B
1. CHECK CHANGEOVER SWITCH SIGNAL
With CONSULT-II
Check the operation on (MIR CHNG SW-R” or “MIR CHNG SW-L) in the DATA MONITOR.
Without CONSULT-II
1. Turn ignition switch ON.
2. Check voltage between automatic drive positioner control unit connector and ground.
OK
orNG
OK >> Changeover switch circuit is OK.
NG >> GO TO 2.
Monitor item
[OPERATION or UNIT]Contents
MIR CHNG SW–R“ON/
OFF”ON/OFF status judged from the changeover
switch (switching to RIGHT) signal is displayed.
MIR CHNG SW–L“ON/
OFF”ON/OFF status judged from the changeover
switch (switching to LEFT) signal is displayed.
PIIA0191E
Terminals
Change over switch
conditionVoltage (V)
(Approx.) (+)
(-) Automatic
drive posi-
tioner con-
trol unit
connectorTerminal
M62
GroundRIGHT 0
Other than above 5
18LEFT 0
Other than above 5
PIIB6015E

REVERSE INTERLOCK DOOR MIRROR SYSTEM
GW-109
C
D
E
F
G
H
J
K
L
MA
B
GW
Revision: 2007 April2007 M35/M45
5. CHECK AUTOMATIC DRIVE POSITIONER CONTROL UNIT OUTPUT SIGNAL
1. Connect automatic drive positioner control unit connector.
2. Turn ignition switch ON.
3. Check voltage between automatic drive positioner control unit connector and ground.
OK or NG
OK >> Check the condition of harness and connector.
NG >> Replace automatic drive positioner control unit.
Check Mirror Switch Circuit NIS0023C
1. CHECK MIRROR SWITCH SIGNAL
With CONSULT-II
Check the operation on “(MIR CON SW–UP/DN) and (MIR CON SW–RH/LH) in the DATA MONITOR.
Without CONSULT-II
1. Turn ignition switch to ON position.
2. Check voltage between automatic drive positioner control unit connector and ground.
OK or NG
OK >> Mirror switch circuit is OK.
NG >> GO TO 2.
Terminals
Voltage (V)
(Approx.) (+)
(-) Automatic drive
positioner control
unit connectorTerminal
M62
Ground 5
18
PIIB6015E
Monitor item
[OPERATION or UNIT]Contents
MIR CON SW–UP“ON/
OFF”ON/OFF status judged from the mirror switch
(UP) signal is displayed.
MIR CON SW–DN“ON/
OFF”ON/OFF status judged from the mirror switch
(DOWN) signal is displayed.
MIR CON SW–RH“ON/
OFF”ON/OFF status judged from the mirror switch
(RIGHT) signal is displayed.
MIR CON SW–LH“ON/
OFF”ON/OFF status judged from the mirror switch
(LEFT) signal s displayed.
PIIA0199E
Te r m i n a l s
Mirror switch
ConditionVoltage (V)
(Approx.) (+)
(–) Automatic drive
positioner control
unit connectorTerminal
M63
GroundUP 0
Other than above 5
4LEFT 0
Other than above 5
19DOWN 0
Other than above 5
20RIGHT 0
Other than above 5
PIIB6019E

GW-114
REVERSE INTERLOCK DOOR MIRROR SYSTEM
Revision: 2007 April2007 M35/M45
Check Mirror Sensor Circuit NIS0023E
1. CHECK MIRROR SENSOR INSPECTION
With CONSULT-II
Check the voltage on (MIR/SE LH R–L, MIR/SE LH U–D, MIR/SE RH R–L, MIR/SE RH U–D) in the DATA
MONITOR.
Without CONSULT-II
1. Turn ignition switch ON.
2. Check voltage between automatic drive positioner control unit connector and ground.
OK or NG
OK >> Mirror sensor LH circuit is OK.
NG >> GO TO 3.
2. CHECK MIRROR SENSOR POWER SUPPLY 1
Check voltage between door mirror connector and ground.
OK or NG
OK >> GO TO 5.
NG >> GO TO 3.
Monitor item
[OPERATION or UNIT]Contents
MIR/SE LH R–L “V”Voltage output from door mirror LH horizontal sensor
(LH/RH) is displayed.
MIR/SE LH U–D “V”Voltage output from door mirror LH vertical sensor
(UP/DOWN) is displayed.
MIR/SE RH R–L “V”Voltage output from door mirror RH horizontal sensor
(LH/RH) is displayed.
MIR/SE RH U–D “V”Voltage output from door mirror RH vertical sensor
(UP/DOWN) is displayed.
PIIA0197E
Terminals
Mirror face positionVoltage (V)
(Approx.) (+)
(-) Automatic drive
positioner control
unit connectorTerminal
M6Door
mirror
RH side5
GroundClose to perk 4.2
Close to valley 0.5
21Close to left edge 3.5
Close to right edge 0.5
Door
mirror
LH side6Close to perk 4.2
Close to valley 0.5
22Close to left edge 0.5
Close to right edge 3.5
PIIB6027E
Terminals
Voltage (V)
(Approx.) (+)
(-)
Door mirror
connectorTe r m i n a l
D2 (LH)
D39 (RH)11 Ground Battery voltage
PIIB6032E

IDX-3
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
Camshaft position sensor (PHASE) EC-371, EC-1082
Camshaft(VK45DE) ......................................... EM-215
Camshaft(VQ35DE) ........................................... EM-85
CAN .................................................................. DI-109
CAN - Wiring diagram .......... EC-162, EC-866, AT-106
CAN (Controller Area Network) ... SB-5, BL-26, BL-59,
BL-221
, GW-19, GW-73, GW-95, SE-16
CAN communication ........... EC-161, EC-164, EC-740,
EC-865
, EC-868, AT-32, AT-105, TF-13, TF-32, SB-5,
BL-26
, BL-59, BL-221, GW-19, GW-73, GW-95, SE-16,
WW-11
Canister-See EVAP canister ............... EC-42, EC-744
Center bearing assembly (propeller shaft) ........ PR-12
Center bearing disassembly (propeller shaft) .... PR-11
CHARGE - Wiring diagram ................................ SC-22
Charging system ................................................ SC-20
Chassis and body maintenance ........................ MA-29
CHIME - Wiring diagram ..................................... DI-63
CIGAR - Wiring diagram .................................. WW-50
Cigarette lighter ............................................... WW-50
Circuit breaker ................................................... PG-17
Clock ................................................................. DI-107
CLOCK - Wiring diagram .................................. DI-107
Closed loop control .............................. EC-32, EC-734
Closed loop control (Bank 1) ........... EC-496, EC-1211
Closed loop control (Bank 2) ........... EC-496, EC-1211
Collision diagnosis ........................................... SRS-54
Combination lamp, front, removal and installation ........
LT-75
Combination lamp, rear, removal and installation ........
LT-265
Combination meter ............................................... DI-5
COMPAS - Wiring diagram ............................... DI-105
Compass .......................................................... DI-102
Component Location (auto A/C) ...................... ATC-42
Compression pressure(VK45DE) .................... EM-235
Compression pressure(VQ35DE) .................... EM-102
Compressor special service tool ...................... ATC-16
Condenser ..................................................... ATC-164
Connecting rod bearing clearance(VK45DE) .. EM-275
Connecting rod bushing clearance .................. EM-143
Connecting rod bushing clearance(VK45DE) .. EM-271
Connecting rod(VK45DE) ................................ EM-271
Connecting rod(VQ35DE) ................................ EM-141
CONSULT-II Reference value (A/T) .................. AT-90
Control units (terminal arrangement) ............... PG-107
Control valve (A/T) ............................................. AT-38
Controller Area Network (CAN) ... SB-5, BL-26, BL-59,
BL-221
, GW-19, GW-73, GW-95, SE-16
Converter housing installation ............ AT-277, AT-280
COOL/F - Wiring diagram ................ EC-502, EC-1217
Coolant replacement(VQ35DE) ......................... MA-15
Cooling circuit (engine)(VK45DE) ...................... CO-38
Cooling circuit (engine)(VQ35DE) ....................... CO-9
Cooling fan motor ............................ EC-509, EC-1224
Cooling fan(VK45DE) ........................................ CO-51
Cooling fan(VQ35DE) ........................................ CO-22
Cowl top ............................................................... EI-18
Cowl top cover ..................................................... EI-18
Crankcase ventilation system - See Positive crankcase
ventilation ............................................. EC-51
, EC-753
Crankshaft position sensor (POS) ... EC-364, EC-1075
Crankshaft(VK45DE) ...................................... EM-253
Crankshaft(VQ35DE) ...................................... EM-141
Crash zone sensor .......................................... SRS-49
CUR/SE - Wiring diagram .. EC-526, EC-533, EC-540,
EC-547
, EC-1239, EC-1246, EC-1253, EC-1260
Cylinder block boring(VK45DE) ...................... EM-274
Cylinder block(VK45DE) ................................. EM-252
Cylinder block(VQ35DE) ................................. EM-124
Cylinder head bolt tightening(VK45DE) .......... EM-237
Cylinder head bolt tightening(VQ35DE) .......... EM-105
Cylinder head(VK45DE) ................................. EM-235
Cylinder head(VQ35DE) ................................. EM-102
D
D/LOCK - Wiring diagram .................................. BL-28
Daytime light system ........................................... LT-78
Daytime running light - See Daytime light system LT-78
DEF - Wiring diagram ............................ SB-7, SE-119
Diagnosis sensor unit ..................................... SRS-52
Diagnostic trouble code (DTC) for OBD system EC-16,
EC-59
, EC-718, EC-761
Direct clutch solenoid valve ............... AT-155, AT-157
Display and amp.assembly ............... ATC-54, ATC-67
Door glass ........................................... GW-61, GW-65
Door glass Fitting Adjustment(Front) ................ GW-64
Door glass Fitting Adjustment(Rear) ................. GW-68
Door lock .......................................................... BL-194
Door mirror ...................................................... GW-118
Door trim ............................................................. EI-34
Door, front ........................................... BL-188, GW-61
Door, rear ............................................ BL-188, GW-65
Drive belt inspection ......................................... MA-22
Drive belt(VK45DE) ........................................ EM-174
Drive belt(VQ35DE) .......................................... EM-16
Drive shaft ......................................................... MA-38
Drive shaft (rear) ............................................... RAX-8
Driver air bag .................................................. SRS-42
DTRL - Wiring diagram ....................................... LT-83
Duct and grilles .............................................. ATC-143
E
ECM power supply EC-154
, EC-479, EC-858, EC-1186
ECM/PW - Wiring diagram ............... EC-480, EC-1187
ECTS - Wiring diagram ...................... EC-216, EC-928
Electric sunroof .................................................. RF-10
Electric throttle control actuator ........ EC-604, EC-615,
EC-1322
, EC-1334
Electric throttle control actuator (VK45DE) ..... EM-179
Electric throttle control actuator (VQ35DE) ....... EM-21
Electrical load signal circuit .............. EC-667, EC-1387
Electrical unit ................................................... PG-107
Electrical units location ...................................... PG-98
Electronic ignition (EI) system ............. EC-33, EC-735
Engine control module (ECM) .......... EC-483, EC-1190

INSTRUMENT PANEL ASSEMBLY
IP-11
C
D
E
F
G
H
J
K
L
MA
B
IP
Revision: 2007 April2007 M35/M45
Removal and Installation of Instrument Panel & PadNIS0025D
REMOVAL
1. Remove cup holder.

Backside pull up.
2. Remove switch finisher.

Disconnect harness connector.
3. Remove A/T console finisher.

Place the selector lever in "D" position.

Remove selector lever knob. Refer to AT- 2 2 2 , "Control Device
Removal and Installation" .

Lift up backside and pull back.

Disconnect harness connector.
4. Remove cluster lid C.

Pull back.

Disconnect harness connector.
1. Cup holder 2. Switch finisher 3. A/T console finisher
4. Cluster lid C 5. Console rear finisher 6. Center console
7. Glove box 8. Instrument passenger lower cover 9. Instrument side finisher (RH)
10. Glove box cover 11. Instrument finisher B 12. Instrument side finisher (LH)
13. Instrument driver lower panel 14. Instrument finisher A 15. Instrument finisher C
16. Cluster lid A 17. Combination meter 18. Steering column cover
19. Upper ventilator gurille 20. Center ventilator grille 21. Multifunction switch
22. Front display unit 23. Audio assembly 24. NAVI C/U
25. Side ventilator grille (RH/LH) 26. Front defroster grille 27. Instrument panel & pad
Pawl Clip Metal clip
PIIB4107J
PIIB4108E
PIIB4109E

IP-14
INSTRUMENT PANEL ASSEMBLY
Revision: 2007 April2007 M35/M45
20. Remove center ventilator grille.

Insert a remover into rear lower space.

Pull up.
21. Remove multifunction switch. Refer to AV- 2 8 4 , "
Multifunction Switch" .
22. Remove front display unit. Refer to AV- 2 8 3 , "
Front Display Unit" .
23. Remove audio assembly. Refer to AV- 2 7 7 , "
Audio Unit" .
24. Remove NAVI C/U. Refer to AV- 2 8 2 , "
AV (NAVI) Control Unit" .
25. Remove side ventilator grille (RH/LH).

Insert a remover into lower space.

Pull back.
26. Remove front defroster grille.

Insert a remover into back space.

Disconnect harness connector.
27. Remove instrument panel & pad.

Remove front passenger air bag module mounting bolt and disconnect harness connector. Refer to
SRS-46, "
FRONT PASSENGER AIR BAG MODULE" .

Remove front pillar garnish. Refer to EI-38, "FRONT PILLAR GARNISH" .
INSTALLATION
Install in the reverse order of removal.
CAUTION:

To install, confirm locating pins on back of instrument panel are completely inserted into holes on
vehicle.

Do not leave harness stuck when installing.
PIIB4121E
PIIB4123E
PIIB4122E

TROUBLE DIAGNOSIS
LAN-9
[CAN FUNDAMENTAL]
C
D
E
F
G
H
I
J
L
MA
B
LAN
Revision: 2007 April2007 M35/M45
Example: Data link connector branch line open circuit
NOTE:

When data link connector branch line is open, transmission and reception of CAN communication signals
are not affected. Therefore, no symptoms occur. However, be sure to repair malfunctioning circuit.

When data link connector branch line is open, the screen-display of the CONSULT-II “SELECT SYSTEM”
screen may be the same as when the CAN communication line has short-circuit. However, symptoms dif-
fer depending on the case. See below chart for the differences.
SKIB8739E
Unit name Symptom
ECM
Normal operation. BCM
EPS control unit
Combination meter
ABS actuator and electric unit (control unit)
TCM
IPDM E/R
SELECT SYSTEM
(CONSULT-II)Difference of symptom
Data link connector branch line open cir-
cuit
All Diag on CAN units are not
indicated.Normal operation.
CAN-H, CAN-L harness short-circuitMost of the units which are connected to the CAN
communication system enter fail-safe mode or are
deactivated.

LAN-14
[CAN FUNDAMENTAL]
TROUBLE DIAGNOSIS
Revision: 2007 April2007 M35/M45
MONITOR ITEM (ON-BOARD DIAGNOSIS)
NOTE:
For some models, CAN communication diagnosis result is received from the vehicle monitor. (CONSULT-II is
not available.)
Example: Vehicle Display
ItemResult indi-
catedError counter Description
CAN_COMM
(Initial diagnosis)OK 0 Normal at present
NG 1 – 50Control unit error
(The number indicates how many times diagnosis has been
run.)
CAN_CIRC_1
(Transmission diagnosis)OK 0 Normal at present
UNKWN 1 – 50Unable to transmit for 2 seconds or more at present.
(The number indicates how many times diagnosis has been
run.)
CAN_CIRC_2 – 9
(Reception diagnosis of each unit)OK 0 Normal at present
UNKWN 1 – 50Unable to transmit for 2 seconds or more at present.
(The number indicates how many times diagnosis has been
run.)
Diagnosis not performed.
No control unit for receiving signals. (No applicable optional
parts)

TROUBLE DIAGNOSES WORK FLOW
LAN-23
[CAN FUNDAMENTAL]
C
D
E
F
G
H
I
J
L
MA
B
LAN
Revision: 2007 April2007 M35/M45
Create On-board Diagnosis Copy Sheet
Display the trouble diagnosis result of CAN communication with the on-board diagnosis function on the vehicle
monitor, etc. Copy them on the on-board diagnosis copy sheet.
NOTE:
For some models, CAN communication diagnosis result is received from the vehicle monitor. (CONSULT-II is
not available.)
SKIB8722E