relay INFINITI M35 2007 Factory Workshop Manual

TROUBLE DIAGNOSIS
BRC-25
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
Revision: 2007 April2007 M35/M45
DISPLAY ITEM LIST
Code Display item Malfunction detecting condition Check item
C1101 RR RH SENSOR-1Circuit of rear RH wheel sensor is open. Or when the sensor power
voltage is outside the standard.
BRC-34, "
Wheel
Sensor Circuit"
(Note 1) C1102 RR LH SENSOR-1Circuit of rear LH wheel sensor is open. Or when the sensor power volt-
age is outside the standard.
C1103 FR RH SENSOR-1Circuit of front RH wheel sensor is open. Or when the sensor power
voltage is outside the standard.
C1104 FR LH SENSOR-1Circuit of front LH wheel sensor is open. Or when the sensor power
voltage is outside the standard.
C1105 RR RH SENSOR-2When the circuit in the rear RH wheel sensor is short-circuited. Or when
the distance between the wheel sensor and sensor rotor is too large
and the sensor pulse cannot be recognized by the control unit.
C1106 RR LH SENSOR-2When the circuit in the rear LH wheel sensor is short-circuited. Or when
the distance between the wheel sensor and sensor rotor is too large
and the sensor pulse cannot be recognized by the control unit.
C1107 FR RH SENSOR-2When the circuit in the front RH wheel sensor is short-circuited. Or
when the distance between the wheel sensor and sensor rotor is too
large and the sensor pulse cannot be recognized by the control unit.
C1108 FR LH SENSOR- 2When the circuit in the front LH wheel sensor is short-circuited. Or
when the distance between the wheel sensor and sensor rotor is too
large and the sensor pulse cannot be recognized by the control unit.
C1109BATTERY VOLTAGE
[ABNORMAL]When the ABS actuator and electric unit (control unit) power supply
voltage is lower than normal.BRC-37, "
ABS
Actuator and
Electric Unit
(Control Unit)
Power Supply
and Ground Cir-
cuit"
C1110 CONTROLLER FAILUREWhen there is an internal malfunction in the ABS actuator and electric
unit (control unit).BRC-36, "
ABS
Actuator and
Electric Unit
(Control Unit)"
C 1111 P U M P M O TO RDuring the actuator motor operating with ON, when the actuator motor
turns OFF, or when the control line for actuator motor relay is open.BRC-38, "
ABS
Motor and Motor
Relay Circuit"During the actuator motor operating with OFF, when the actuator motor
turns ON, or when the control line for relay is shorted to ground.
C1114 MAIN RELAYDuring the actuator relay operating with OFF, when the actuator relay
turns ON, or when the control line for the relay is shorted to the ground.BRC-39, "
Sole-
noid, VDC
Change-Over
Valve and Actua-
tor Relay Circuit"
During the actuator relay operating with ON, when the actuator relay
turns OFF, or when the control line for the relay is open.
C 111 5ABS SENSOR
[ABNORMAL SIGNAL]When wheel sensor input signal is malfunctioning.BRC-34, "
Wheel
Sensor Circuit"
(Note 1)
C1116 STOP LAMP SW When stop lamp switch circuit is open.BRC-43, "
Stop
Lamp Switch Cir-
cuit"

BRC-26
[VDC/TCS/ABS]
TROUBLE DIAGNOSIS
Revision: 2007 April2007 M35/M45
C1120 FR LH IN ABS SOLWhen the control unit detects a malfunction in the front left inlet sole-
noid circuit.
BRC-39, "
Sole-
noid, VDC
Change-Over
Valve and Actua-
tor Relay Circuit"
C1121 FR LH OUT ABS SOLWhen the control unit detects a malfunction in the front left outlet sole-
noid circuit.
C1122 FR RH IN ABS SOLWhen the control unit detects a malfunction in the front right inlet sole-
noid circuit.
C1123 FR RH OUT ABS SOLWhen the control unit detects a malfunction in the front right outlet sole-
noid circuit.
C1124 RR LH IN ABS SOLWhen the control unit detects a malfunction in the rear left inlet solenoid
circuit.
C1125 RR LH OUT ABS SOLWhen the control unit detects a malfunction in the rear left outlet sole-
noid circuit.
C1126 RR RH IN ABS SOLWhen the control unit detects a malfunction in the rear right inlet sole-
noid circuit.
C1127 RR RH OUT ABS SOLWhen the control unit detects a malfunction in the rear right outlet sole-
noid circuit.
C1130 ENGINE SIGNAL 1
Major engine components are malfunctioning.BRC-36, "
Engine
System"
C1131 ENGINE SIGNAL 2
C1132 ENGINE SIGNAL 3
C1133 ENGINE SIGNAL 4
C1136 ENGINE SIGNAL 6
C1137 RAS CIRCUIT When RAS control unit is malfunctioning.BRC-47, "
RAS
Control Unit Cir-
cuit (With RAS)"
C1142 PRESS SEN CIRCUIT Pressure sensor signal line is open or shorted, or pressure sensor is
malfunctioning.BRC-40, "
Pres-
sure Sensor Cir-
cuit"
C1143 ST ANG SEN CIRCUIT Neutral position of steering angle sensor is dislocated, or the steering
angle sensor is malfunctioning.BRC-41, "
St e e r -
ing Angle Sensor
Circuit"
C1144 ST ANG SEN SIGNAL Neutral position correction of steering angle sensor is not finished.BRC-6, "
Adjust-
ment of Steering
Angle Sensor
Neutral Position"
C1145 YAW RATE SENSOR Yaw rate sensor is malfunctioning, or the yaw rate sensor signal line is
open or shorted.BRC-44, "Ya w
Rate/Side G
Sensor Circuit"C1146 SIDE G-SEN CIRCUITSide G sensor is malfunctioning, or circuit of side G sensor is open or
shorted.
C1147 USV LINE [FL-RR]VDC switch-over solenoid valve (USV1) on the primary side is open cir-
cuit or shorted, or the control line is open or shorted to the power supply
or the ground.
BRC-39, "
Sole-
noid, VDC
Change-Over
Valve and Actua-
tor Relay Circuit"
C1148 USV LINE [FR-RL]VDC switch-over solenoid valve (USV2) on the secondary side is open
circuit or shorted, or the control line is open or shorted to the power
supply or the ground.
C1149 HSV LINE [FL-RR]VDC switch-over solenoid valve (HSV1) on the primary side is open cir-
cuit or shorted, or the control line is open or shorted to the power supply
or the ground.
C1150 HSV LINE [FR-RL]VDC switch-over solenoid valve (HSV2) on the secondary side is open
circuit or shorted, or the control line is open or shorted to the power
supply or the ground.
C1153 EMERGENCY BRAKEWhen ABS actuator and electric unit (control unit) is malfunctioning.
(Pressure increase is too much or too little)BRC-36, "
ABS
Actuator and
Electric Unit
(Control Unit)"
Code Display item Malfunction detecting condition Check item

TROUBLE DIAGNOSIS
BRC-29
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
Revision: 2007 April2007 M35/M45
FR RH IN SOL
(ON/OFF)—××
Operation status of all solenoid valve FR RH OUT SOL
(ON/OFF)—××
FR LH IN SOL
(ON/OFF)—××
FR LH OUT SOL
(ON/OFF)—××
RR RH IN SOL
(ON/OFF)—××
RR RH OUT SOL
(ON/OFF)—××
RR LH IN SOL
(ON/OFF)—××
RR LH OUT SOL
(ON/OFF)—××
MOTOR RELAY
(ON/OFF)—××Motor and motor relay operation
ACTUATOR RLY
(ON/OFF)—××Actuator relay operation
ABS WARN LAMP
(ON/OFF)—××ABS warning lamp
OFF LAMP
(ON/OFF)—××VDC OFF indicator lamp
SLIP LAMP
(ON/OFF)—××SLIP indicator lamp
4WD FAIL REQ
(ON/OFF) (Note)——×AWD control unit fail-safe signal
SNOW MODE SW
(ON/OFF)——×Snow mode switch
BST OPER SIG — —×Not applied but displayed.
M-MODE SIG
(ON/OFF)——×Manual mode activated
EBD SIGNAL
(ON/OFF)——×EBD operation
ABS SIGNAL
(ON/OFF)——×ABS operation
TCS SIGNAL
(ON/OFF)——×TCS operation
VDC SIGNAL
(ON/OFF)——×VDC operation
EBD FAIL SIG
(ON/OFF)——×EBD fail-safe signal
ABS FAIL SIG
(ON/OFF)——×ABS fail-safe signal
TCS FAIL SIG
(ON/OFF)——×TCS fail-safe signal
VDC FAIL SIG
(ON/OFF)——×VDC fail-safe signal
CRANKING SIG
(ON/OFF)——×Crank operation Item
(Unit)Data monitor item selection
Display content
ECU INPUT
SIGNALSMAIN SIGNALSSELECTION
FROM MENU

BRC-30
[VDC/TCS/ABS]
TROUBLE DIAGNOSIS
Revision: 2007 April2007 M35/M45
×:Applicable
–:Not applicable
Note: Only AWD models
Active TestNFS000QI
CAUTION:

Do not perform active test while driving vehicle.

Make sure to completely bleed air from brake system.

The active test cannot be performed with the ABS warning lamp, VDC indicator lamp, SLIP indica-
tor lamp and brake warning lamp are on.

ABS warning lamp, VDC OFF indicator lamp, SLIP indicator lamp and brake warning lamp are on
during active test.

Erase memory of ICC system after implementing active test. Refer to ACS-34, "Self-Diagnostic
Function" .
OPERATION PROCEDURE
1. Perform “CONSULT-II Starting Procedure”. Refer to GI-38, "CONSULT-II Start Procedure" .
2. Touch “SELECT TEST ITEM” is displayed.
3. Touch necessary test item.
4. While “MAIN SIGNALS” indication is inverted, touch “START”.
5. “ACTIVE TEST” screen will be displayed so perform the following test.
NOTE:

When active test is performed while depressing the pedal, the pedal depression amount will change.
This is normal. (Only solenoid valve and ABS motor)

“TEST IS STOPPED” is displayed 10 seconds after operation start.

After “TEST IS STOPPED” is displayed, to perform test again, touch “BACK” and repeat step 3.
USV[FR-RL]
(ON/OFF)——×
VDC switch-over valve USV[FL-RR]
(ON/OFF)——×
HSV[FR-RL]
(ON/OFF)——×
HSV[FL-RR]
(ON/OFF)——×
V/R OUTPUT
(ON/OFF)——×Solenoid valve relay activated
M/R OUTPUT
(ON/OFF)——×Actuator motor and motor relay activated Item
(Unit)Data monitor item selection
Display content
ECU INPUT
SIGNALSMAIN SIGNALSSELECTION
FROM MENU
SFIA0591E

TROUBLE DIAGNOSIS
BRC-31
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
Revision: 2007 April2007 M35/M45
TEST ITEMS
Solenoid Valve
NOTE:
The example shown is for front right wheel. The procedure for the other wheels is the same as given below.

When performing an active test of the ABS function, select the
"MAIN SIGNALS" for each test item. In addition, when perform-
ing an active test of the VDC/TCS function, select the item menu
for each test item.

For ABS solenoid valve, touch “UP”, “KEEP”, and “DOWN” on
the display screen. For ABS solenoid valve (ACT), touch “UP”,
“ACT UP”, “ACT KEEP” and confirm that solenoid valves (IN,
OUT, USV, HSV) operate as shown in the table below.
*: ON for 1 to 2 seconds after the touch, and then OFF
Note: A brief moment of ON/OFF condition occurs every 20 seconds after ignition switch turned ON. This is not malfunction because it is
an operation for checking.
ABS Motor
Touch “ON” and “OFF” on screen. Make sure motor relay and actua-
tor relay operates as shown in table below.
Note: A brief moment of ON/OFF condition occurs every 20 seconds after ignition
switch turned ON. This is not malfunction because it is an operation for checking.
SFIA0678E
Operation
(Note)ABS solenoid valve ABS solenoid valve (ACT)
UP KEEP DOWN UP ACT UP ACT KEEP
FR RH IN SOL OFF ON ON OFF OFF OFF
FR RH OUT SOL OFF OFF ON* OFF OFF OFF
USV [FR-RL] OFF OFF OFF OFF ON ON
HSV [FR-RL] OFF OFF OFF OFF ON* OFF
Operation ON OFF
MOTOR RELAY ON OFF
ACTUATOR RLY (Note) ON ON
SFIA0593E

BRC-38
[VDC/TCS/ABS]
TROUBLE DIAGNOSIS FOR SYSTEM
Revision: 2007 April2007 M35/M45
ABS Motor and Motor Relay CircuitNFS000QP
INSPECTION PROCEDURE
1. CHECK SELF-DIAGNOSIS RESULTS
Check self-diagnosis results.
Is above displayed on the self-diagnosis display?
YES >> GO TO 2.
NO >> INSPECTION END
2. CHECK CONNECTOR
1. Turn ignition switch OFF and disconnect ABS actuator and electric unit (control unit) connector E30,
check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or
replace terminal.
2. Reconnect connector and perform self-diagnosis.
OK or NG
OK >> INSPECTION END
NG >> GO TO 3.
3. CHECK ABS MOTOR AND MOTOR RELAY POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF and disconnect ABS actuator and electric unit (control unit) connector E30.
2. Check voltage between the ABS actuator and electric unit (con-
trol unit) harness connector E30 terminal 2 and ground.
OK or NG
OK >> GO TO 4.
NG >>

Repair or replace malfunctioning components.

Perform the self-diagnosis, and make sure that the
result shows “NO DTC IS DETECTED”.
4. CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) GROUND CIRCUIT
Check continuity between ABS actuator and electric unit (control
unit) harness connector E30 terminals 1, 4 and ground.
OK or NG
OK >>
Replace ABS actuator and electric unit (control unit).

Perform the self-diagnosis, and make sure that the
result shows “NO DTC IS DETECTED”.
NG >>

Repair or replace malfunctioning components.

Perform the self-diagnosis, and make sure that the
result shows “NO DTC IS DETECTED”.
Self-diagnosis results
PUMP MOTOR
ABS actuator and electric unit (control unit) Ground Voltage
2—Battery voltage
(Approx. 12 V)
SFIA3034E
ABS actuator and electric unit (control unit) Ground Continuity
1, 4 — Yes
SFIA3033E

TROUBLE DIAGNOSIS FOR SYSTEM
BRC-39
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
Revision: 2007 April2007 M35/M45
Solenoid, VDC Change-Over Valve and Actuator Relay CircuitNFS000QQ
INSPECTION PROCEDURE
1. CHECK SELF-DIAGNOSIS RESULTS
Check self-diagnosis results.
Is above displayed on the self-diagnosis display?
YES >> GO TO 2.
NO >> INSPECTION END
2. CHECK CONNECTOR
1. Turn ignition switch OFF and disconnect ABS actuator and electric unit (control unit) connector E30,
check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or
replace terminal.
2. Reconnect connector and perform self-diagnosis.
OK or NG
OK >> INSPECTION END
NG >> GO TO 3.
3. CHECK SOLENOID, VDC CHANGE-OVER VALVE AND ACTUATOR RELAY POWER SUPPLY CIR-
CUIT
1. Turn ignition switch OFF and disconnect ABS actuator and electric unit (control unit) connector E30.
2. Check voltage between ABS actuator and electric unit (control
unit) harness connector E30 terminal 3 and ground.
OK or NG
OK >> GO TO 4.
NG >>

Repair or replace malfunctioning components.

Perform the self-diagnosis, and make sure that the
result shows “NO DTC IS DETECTED”.
Self-diagnosis results
FR RH IN ABS SOL
FR RH OUT ABS SOL
FR LH IN ABS SOL
FR LH OUT ABS SOL
RR RH IN ABS SOL
RR RH OUT ABS SOL
RR LH IN ABS SOL
RR LH OUT ABS SOL
USV LINE [FL-RR]
USV LINE [FR-RL]
HSV LINE [FL-RR]
HSV LINE [FR-RL]
MAIN RELAY
ABS actuator and electric unit (control unit) Ground Voltage
3—Battery Voltage
(Approx. 12 V)
SFIA3035E

BRC-40
[VDC/TCS/ABS]
TROUBLE DIAGNOSIS FOR SYSTEM
Revision: 2007 April2007 M35/M45
4. CHECK SOLENOID, VDC CHANGE-OVER VALVE, ACTUATOR RELAY GROUND CIRCUIT
Check continuity between ABS actuator and electric unit (control
unit) harness connector E30 terminals 1, 4 and ground.
OK or NG
OK >>
Replace ABS actuator and electric unit (control unit).

Perform the self-diagnosis, and make sure that the
result shows “NO DTC IS DETECTED”.
NG >>

Repair or replace malfunctioning components.

Perform the self-diagnosis, and make sure that the
result shows “NO DTC IS DETECTED”.
Pressure Sensor CircuitNFS000QR
INSPECTION PROCEDURE
1. CHECK SELF-DIAGNOSTIC RESULTS
Check self-diagnosis results.
Is above displayed on the self-diagnosis display?
YES >> GO TO 2.
NO >> INSPECTION END
2. CHECK STOP LAMP SWITCH CONNECTOR
1. Disconnect stop lamp switch connector and ABS actuator and electric unit (control unit) connector.
2. Check terminals for deformation, disconnection, looseness, and so on. If any malfunction is found, repair
or replace terminal.
3. Reconnect connectors securely.
4. Start engine.
5. Repeat pumping brake pedal carefully several times, then perform the self-diagnosis again.
OK or NG
OK >> Connector terminal contact is loose, damaged, open or shorted.
NG >> GO TO 3.
3. CHECK STOP LAMP SWITCH
1. Turn ignition switch OFF.
2. Disconnect stop lamp switch harness connector E124.
3. Operate stop lamp switch and check continuity between stop lamp switch harness connector terminals.
OK or NG
OK >> GO TO 4.
NG >> Replace stop lamp switch. Refer to BR-7, "
Removal and Installation" .
ABS actuator and electric unit (control unit) Ground Continuity
1, 4 — Yes
SFIA3033E
Self-diagnosis results
PRESS SEN CIRCUIT
Terminal Condition Continuity
3 − 4Release stop lamp switch
(When brake pedal is depressed.)Ye s
Push stop lamp switch
(When brake pedal is released.)No

EC-7
C
D
E
F
G
H
I
J
K
L
M
ECA
Revision: 2007 April2007 M35/M45 DTC P2100, P2103 THROTTLE CONTROL MOTOR
RELAY .................................................................... 598
Component Description ........................................ 598
CONSULT-II Reference Value in Data Monitor Mode
. 598
On Board Diagnosis Logic ................................... 598
DTC Confirmation Procedure ............................... 598
Wiring Diagram .................................................... 600
Diagnostic Procedure ........................................... 601
DTC P2101 ELECTRIC THROTTLE CONTROL
FUNCTION .............................................................. 604
Description ........................................................... 604
On Board Diagnosis Logic ................................... 604
DTC Confirmation Procedure ............................... 604
Wiring Diagram .................................................... 605
Diagnostic Procedure ........................................... 606
Component Inspection ......................................... 609
Removal and Installation ...................................... 609
DTC P2118 THROTTLE CONTROL MOTOR ........ 610
Component Description ........................................ 610
On Board Diagnosis Logic ................................... 610
DTC Confirmation Procedure ............................... 610
Wiring Diagram ..................................................... 611
Diagnostic Procedure ........................................... 612
Component Inspection ......................................... 613
Removal and Installation ...................................... 614
DTC P2119 ELECTRIC THROTTLE CONTROL
ACTUATOR ............................................................ 615
Component Description ........................................ 615
On Board Diagnosis Logic ................................... 615
DTC Confirmation Procedure ............................... 615
Diagnostic Procedure ........................................... 616
DTC P2122, P2123 APP SENSOR ........................ 617
Component Description ........................................ 617
CONSULT-II Reference Value in Data Monitor Mode
. 617
On Board Diagnosis Logic ................................... 617
DTC Confirmation Procedure ............................... 618
Wiring Diagram .................................................... 619
Diagnostic Procedure ........................................... 620
Component Inspection ......................................... 622
Removal and Installation ...................................... 623
DTC P2127, P2128 APP SENSOR ........................ 624
Component Description ........................................ 624
CONSULT-II Reference Value in Data Monitor Mode
. 624
On Board Diagnosis Logic ................................... 624
DTC Confirmation Procedure ............................... 625
Wiring Diagram .................................................... 626
Diagnostic Procedure ........................................... 627
Component Inspection ......................................... 630
Removal and Installation ...................................... 630
DTC P2135 TP SENSOR ........................................ 631
Component Description ........................................ 631
CONSULT-II Reference Value in Data Monitor Mode
. 631
On Board Diagnosis Logic ................................... 631
DTC Confirmation Procedure ............................... 632
Wiring Diagram .................................................... 633Diagnostic Procedure ...........................................634
Component Inspection ..........................................637
Removal and Installation ......................................637
DTC P2138 APP SENSOR .....................................638
Component Description ........................................638
CONSULT-II Reference Value in Data Monitor Mode
.638
On Board Diagnosis Logic ....................................638
DTC Confirmation Procedure ...............................639
Wiring Diagram .....................................................640
Diagnostic Procedure ...........................................641
Component Inspection ..........................................645
Removal and Installation ......................................645
DTC P2A00, P2A03 A/F SENSOR 1 ......................646
Component Description ........................................646
CONSULT-II Reference Value in Data Monitor Mode
.646
On Board Diagnosis Logic ....................................646
DTC Confirmation Procedure ...............................646
Wiring Diagram .....................................................648
Diagnostic Procedure ...........................................651
Removal and Installation ......................................656
ASCD BRAKE SWITCH .........................................657
Component Description ........................................657
CONSULT-II Reference Value in Data Monitor Mode
.657
Wiring Diagram .....................................................658
Diagnostic Procedure ...........................................659
Component Inspection ..........................................663
ASCD INDICATOR ..................................................664
Component Description ........................................664
CONSULT-II Reference Value in Data Monitor Mode
.664
Wiring Diagram .....................................................665
Diagnostic Procedure ...........................................666
ELECTRICAL LOAD SIGNAL ................................667
Description ............................................................667
CONSULT-II Reference Value in Data Monitor Mode
.667
Diagnostic Procedure ...........................................667
FUEL INJECTOR ....................................................669
Component Description ........................................669
CONSULT-II Reference Value in Data Monitor Mode
.669
Wiring Diagram .....................................................670
Diagnostic Procedure ...........................................671
Component Inspection ..........................................674
Removal and Installation ......................................674
FUEL PUMP ............................................................675
Description ............................................................675
CONSULT-II Reference Value in Data Monitor Mode
.675
Wiring Diagram .....................................................676
Diagnostic Procedure ...........................................677
Component Inspection ..........................................681
Removal and Installation ......................................682
ICC BRAKE SWITCH .............................................683
Component Description ........................................683
CONSULT-II Reference Value in Data Monitor Mode

EC-14Revision: 2007 April2007 M35/M45 On Board Diagnosis Logic ...................................1302
DTC Confirmation Procedure ..............................1302
Wiring Diagram ....................................................1303
Diagnostic Procedure ..........................................1304
Component Inspection .........................................1305
Removal and Installation .....................................1306
DTC P1805 BRAKE SWITCH ................................1307
Component Description .......................................1307
CONSULT-II Reference Value in Data Monitor Mode
1307
On Board Diagnosis Logic ...................................1307
DTC Confirmation Procedure ..............................1308
Wiring Diagram ....................................................1309
Diagnostic Procedure ..........................................1310
Component Inspection .........................................1315
DTC P2100, P2103 THROTTLE CONTROL MOTOR
RELAY ....................................................................1316
Component Description .......................................1316
CONSULT-II Reference Value in Data Monitor Mode
1316
On Board Diagnosis Logic ...................................1316
DTC Confirmation Procedure ..............................1316
Wiring Diagram ....................................................1318
Diagnostic Procedure ..........................................1319
DTC P2101 ELECTRIC THROTTLE CONTROL
FUNCTION .............................................................1322
Description ...........................................................1322
On Board Diagnosis Logic ...................................1322
DTC Confirmation Procedure ..............................1322
Wiring Diagram ....................................................1323
Diagnostic Procedure ..........................................1324
Component Inspection .........................................1328
Removal and Installation .....................................1328
DTC P2118 THROTTLE CONTROL MOTOR ........1329
Component Description .......................................1329
On Board Diagnosis Logic ...................................1329
DTC Confirmation Procedure ..............................1329
Wiring Diagram ....................................................1330
Diagnostic Procedure ..........................................1331
Component Inspection .........................................1332
Removal and Installation .....................................1333
DTC P2119 ELECTRIC THROTTLE CONTROL
ACTUATOR ............................................................1334
Component Description .......................................1334
On Board Diagnosis Logic ...................................1334
DTC Confirmation Procedure ..............................1334
Diagnostic Procedure ..........................................1335
DTC P2122, P2123 APP SENSOR ........................1336
Component Description .......................................1336
CONSULT-II Reference Value in Data Monitor Mode
1336
On Board Diagnosis Logic ...................................1336
DTC Confirmation Procedure ..............................1337
Wiring Diagram ....................................................1338
Diagnostic Procedure ..........................................1339
Component Inspection .........................................1341
Removal and Installation .....................................1342
DTC P2127, P2128 APP SENSOR ........................1343
Component Description .......................................1343CONSULT-II Reference Value in Data Monitor Mode
1343
On Board Diagnosis Logic ...................................1343
DTC Confirmation Procedure ...............................1344
Wiring Diagram ....................................................1345
Diagnostic Procedure ...........................................1346
Component Inspection .........................................1349
Removal and Installation ......................................1349
DTC P2135 TP SENSOR .......................................1350
Component Description .......................................1350
CONSULT-II Reference Value in Data Monitor Mode
1350
On Board Diagnosis Logic ...................................1350
DTC Confirmation Procedure ...............................1351
Wiring Diagram ....................................................1352
Diagnostic Procedure ...........................................1353
Component Inspection .........................................1356
Removal and Installation ......................................1356
DTC P2138 APP SENSOR .....................................1357
Component Description .......................................1357
CONSULT-II Reference Value in Data Monitor Mode
1357
On Board Diagnosis Logic ...................................1357
DTC Confirmation Procedure ...............................1358
Wiring Diagram ....................................................1359
Diagnostic Procedure ...........................................1360
Component Inspection .........................................1364
Removal and Installation ......................................1364
DTC P2A00, P2A03 A/F SENSOR 1 ......................1365
Component Description .......................................1365
CONSULT-II Reference Value in Data Monitor Mode
1365
On Board Diagnosis Logic ...................................1365
DTC Confirmation Procedure ...............................1365
Wiring Diagram ....................................................1367
Diagnostic Procedure ...........................................1370
Removal and Installation ......................................1376
ASCD BRAKE SWITCH .........................................1377
Component Description .......................................1377
CONSULT-II Reference Value in Data Monitor Mode
1377
Wiring Diagram ....................................................1378
Diagnostic Procedure ...........................................1379
Component Inspection .........................................1383
ASCD INDICATOR .................................................1384
Component Description .......................................1384
CONSULT-II Reference Value in Data Monitor Mode
1384
Wiring Diagram ....................................................1385
Diagnostic Procedure ...........................................1386
ELECTRICAL LOAD SIGNAL ...............................1387
Description ...........................................................1387
CONSULT-II Reference Value in Data Monitor Mode
1387
Diagnostic Procedure ...........................................1387
FUEL INJECTOR ....................................................1389
Component Description .......................................1389
CONSULT-II Reference Value in Data Monitor Mode
1389