AT pan INFINITI M35 2007 Factory Repair Manual

DISASSEMBLY
AT-319
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2007 April2007 M35/M45
66. Remove return spring from servo assembly.
67. Remove O-rings from servo assembly.
68. Remove one of the following parts.

Rear extension assembly (VQ35DE models for 2WD)

Adapter case assembly (AWD models)

Output shaft & companion flange complement (VK45DE models for 2WD)
a.VQ35DE models
i. Remove needle bearing (1) from rear extension (2WD models)
or adapter case (AWD models).
ii. Remove parking actuator support from rear extension (2WD
models) or adapter case (AWD models).
SCIA5717E
SCIA5719E
SCIA6179J
SCIA3423E

AT-320
DISASSEMBLY
Revision: 2007 April2007 M35/M45
iii. Remove parking pawl (with return spring) and pawl shaft from
rear extension (2WD models) or adapter case (AWD models).
iv. Remove return spring (1) from parking pawl (2).
v. Remove rear oil seal from rear extension (2WD models) or
adapter case (AWD models).
CAUTION:
Be careful not to scratch rear extension (2WD models) or
adapter case (AWD models).
b.VK45DE models
i. Remove parking actuator support (1) from output shaft & com-
panion flange complement.
SCIA3424E
SCIA6180J
SCIA5481E
SCIA7065E

DISASSEMBLY
AT-321
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2007 April2007 M35/M45
ii. Remove parking pawl (with return spring) (1) and pawl shaft (2)
from output shaft & companion flange complement.
iii. Remove return spring (1) from parking pawl (2).
SCIA7066E
SCIA6180J

REPAIR FOR COMPONENT PARTS
AT-329
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2007 April2007 M35/M45
DISASSEMBLY
1. Compress snap ring using 2 flat-bladed screwdrivers.
2. Remove front carrier assembly and input clutch assembly from
rear internal gear.
3. Remove front carrier assembly from input clutch assembly.
a. Remove bearing race from front carrier assembly.
b. Remove needle bearing from front carrier assembly.
c. Remove snap ring from front carrier assembly.
CAUTION:
Do not expand snap ring excessively.
SCIA5339E
SCIA2847E
SCIA5233E
SCIA5476E

AT-332
REPAIR FOR COMPONENT PARTS
Revision: 2007 April2007 M35/M45
d. Install O-ring and seal rings in input clutch assembly.
CAUTION:

Do not reuse O-ring and seal rings.

Apply ATF to O-ring.

Apply petroleum jelly to seal rings.
2. Install front carrier assembly.
a. Install snap ring to front carrier assembly.
CAUTION:
Do not expand snap ring excessively.
b. Install needle bearing in front carrier assembly.
CAUTION:

Take care with the direction of needle bearing. Refer to
AT- 2 9 8 , "
Locations of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings" .

Apply petroleum jelly to needle bearing.
c. Install bearing race in front carrier assembly.
CAUTION:
Apply petroleum jelly to bearing race.
d. Install front carrier assembly to input clutch assembly.
3. Compress snap ring using 2 flat-bladed screwdrivers.
4. Install front carrier assembly and input clutch assembly to rear
internal gear.
SCIA5235E
SCIA5476E
SCIA5233E
SCIA2847E
SCIA5339E

AT-334
REPAIR FOR COMPONENT PARTS
Revision: 2007 April2007 M35/M45
DISASSEMBLY
1. Remove needle bearing and bearing races from high and low reverse clutch hub.

VQ35DE models

VK45DE models
2. Using a pair of snap ring pliers, remove snap ring from mid sun
gear assembly.
CAUTION:
Do not expand snap ring excessively.
3. Remove high and low reverse clutch hub from mid sun gear
assembly.
SCIA2854E
SCIA5238E
SCIA2855E
SCIA2856E

REPAIR FOR COMPONENT PARTS
AT-337
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2007 April2007 M35/M45
3. Using a flat-bladed screwdriver, install snap ring to rear sun
gear.
4. Install rear sun gear assembly to mid sun gear assembly.
5. Install needle bearing to high and low reverse clutch hub.
CAUTION:

Take care with the direction of needle bearing. Refer to
AT- 2 9 8 , "
Locations of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings" .

Apply petroleum jelly to needle bearing.
6. Install high and low reverse clutch hub to mid sun gear assem-
bly.
7. Using a pair of snap ring pliers, install snap ring to mid sun gear
assembly.
CAUTION:
Do not expand snap ring excessively.
SCIA2859E
SCIA7018E
SCIA2857E
SCIA2856E
SCIA2855E

ASSEMBLY
AT-349
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2007 April2007 M35/M45
24. Install revolution sensor to transmission case. Tighten revolution
sensor bolt to the specified torque. Refer to AT- 2 8 1 , "
Compo-
nents" .
CAUTION:

Do not subject it to impact by dropping or hitting it.

Do not disassemble.

Do not allow metal filings, etc., to get on the sensor's
front edge magnetic area.

Do not place in an area affected by magnetism.
25. Assemble one of the following parts.

Rear extension assembly (VQ35DE models for 2WD)

Adapter case assembly (AWD models)

Output shaft & companion flange complement (VK45DE models for 2WD)
a.VQ35DE models
i. As shown in the figure, use the drift to drive rear oil seal into the
rear extension (2WD models) or adapter case (AWD models)
until it is flush.
CAUTION:

Apply ATF to rear oil seal.

Do not reuse rear oil seal.
ii. Install return spring (1) to parking pawl (2).
SCIA2320E
SCIA5477E
SCIA6180J

ASSEMBLY
AT-351
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2007 April2007 M35/M45
ii. Install parking pawl (with return spring) (1) and pawl shaft (2) to
output shaft & companion flange complement.
iii. Install parking actuator support (1) from output shaft & compan-
ion flange complement.
26. Assemble one of the following parts.

Rear extension assembly (VQ35DE models for 2WD)

Adapter case assembly (AWD models)

Output shaft & companion flange complement (VK45DE models for 2WD)
a.VQ35DE models for 2WD
i. Install seal rings to output shaft.
CAUTION:

Do not reuse seal rings.

Apply petroleum jelly to seal rings.
ii. Install parking gear to output shaft.
SCIA7066E
SCIA7065E
SCIA5209E
SCIA5247E

ASSEMBLY
AT-353
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2007 April2007 M35/M45
b.VK45DE models for 2WD
i. Install seal rings to intermediate shaft.
CAUTION:

Do not reuse seal rings.

Apply petroleum jelly to seal rings.
ii. Install intermediate shaft in transmission case.
CAUTION:
Be careful not to mistake front for rear because both sides
looks similar. (Thinner end is front side.)
iii. Apply recommended sealant (Genuine Anaerobic Liquid Gasket
or equivalent. Refer to GI-47, "
Recommended Chemical Prod-
ucts and Sealants" .) to output shaft & companion flange com-
plement as shown in the figure.
CAUTION:
Completely remove all moisture, oil and old sealant, etc.
from the transmission case and output shaft & companion
flange complement mounting surfaces.
iv. Install output shaft & companion flange complement in transmis-
sion case.
CAUTION:
Insert the tip of parking rod between the parking pawl and
the parking actuator support when assembling the output
shaft & companion flange complement.
SCIA5714E
SCIA5713E
SCIA5212E
SCIA5712E