control INFINITI M35 2007 Factory Service Manual

EC-742
[VK45DE]
EVAPORATIVE EMISSION SYSTEM
Revision: 2007 April2007 M35/M45
EVAPORATIVE EMISSION LINE DRAWING
: Vehicle front : From next page
1. Intake manifold collector 2. EVAP canister purge volume control
solenoid valve3. EVAP service port
NOTE:
Do not use soapy water or any type of solvent while installing vacuum hose or purge hoses.
PBIB2726E

EVAPORATIVE EMISSION SYSTEM
EC-743
[VK45DE]
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: 2007 April2007 M35/M45
: Vehicle front : To previous page
1. EVAP canister vent control valve 2. EVAP canister 3. EVAP control system pressure sensor
NOTE:
Do not use soapy water or any type of solvent while installing vacuum hose or purge hoses.
PBIB2727E

EC-744
[VK45DE]
EVAPORATIVE EMISSION SYSTEM
Revision: 2007 April2007 M35/M45
Component InspectionNBS0059S
EVAP CANISTER
Check EVAP canister as follows:
1. Block port (B).
2. Blow air into port (A) and check that it flows freely out of port (C).
3. Release blocked port (B).
4. Apply vacuum pressure to port (B) and check that vacuum pres-
sure exists at the ports (A) and (C).
5. Block port (A) and (B).
6. Apply pressure to port (C) and check that there is no leakage.
FUEL TANK VACUUM RELIEF VALVE (BUILT INTO FUEL FULLER CAP)
1. Wipe clean valve housing.
2. Check valve opening pressure and vacuum.
3. If out of specification, replace fuel filler cap as an assembly.
CAUTION:
Use only a genuine fuel filler cap as a replacement. If an incor-
rect fuel filler cap is used, the MIL may come on.
EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
Refer to EC-1121 .
FUEL TANK TEMPERATURE SENSOR
Refer to EC-1053 .
EVAP CANISTER VENT CONTROL VALVE
Refer to EC-1128 .
EVAP CONTROL SYSTEM PRESSURE SENSOR
Refer to EC-1144 .
PBIB2728E
SEF445Y
Pressure:
15.3 - 20.0 kPa (0.156 - 0.204 kg/cm2 , 2.22
- 2.90 psi)
Va c u u m :
−6.0 to −3.3 kPa (−0.061 to −0.034 kg/cm
2 ,
−0.87 to −0.48 psi)
SEF943S

EVAPORATIVE EMISSION SYSTEM
EC-745
[VK45DE]
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: 2007 April2007 M35/M45
EVAP SERVICE PORT
Positive pressure is delivered to the EVAP system through the EVAP
service port. If fuel vapor leakage in the EVAP system occurs, use a
leak detector to locate the leak.
Removal and InstallationNBS0059T
EVAP CANISTER
Tighten EVAP canister as shown in the figure.
EVAP CANISTER VENT CONTROL VALVE
1. Turn EVAP canister vent control valve counterclockwise.

Lock (A)

Unlock (B)
2. Remove the EVAP canister vent control valve.
Always replace O-ring with a new one.
How to Detect Fuel Vapor LeakageNBS0059U
CAUTION:

Do not use compressed air or a high pressure pump.

Do not exceed 4.12 kPa (0.042 kg/cm2 , 0.6 psi) of pressure in EVAP system.
NOTE:

Do not start engine.
SEF462UA
1. EVAP control system pressure sensor 2. O-ring 3. EVAP canister
4. O-ring 5. EVAP canister vent control valve
PBIB2729E
PBIB2730E

EVAPORATIVE EMISSION SYSTEM
EC-747
[VK45DE]
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: 2007 April2007 M35/M45
3. Apply battery voltage between the terminals of EVAP canister
vent control valve (1) to make a closed EVAP system.

Illustration shows the view from under the vehicle

: Vehicle front

EVAP canister (2)

EVAP control system pressure sensor (3)
4. To locate the leak, deliver positive pressure to the EVAP system
until pressure gauge points reach 1.38 to 2.76 kPa (0.014 to
0.028 kg/cm
2 , 0.2 to 0.4 psi).
5. Remove EVAP service port adapter and hose with pressure
pump.
6. Locate the leak using a leak detector. Refer to EC-742, "
EVAPORATIVE EMISSION LINE DRAWING" .
PBIB2702E

ON BOARD REFUELING VAPOR RECOVERY (ORVR)
EC-749
[VK45DE]
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: 2007 April2007 M35/M45
Diagnostic ProcedureNBS0059W
SYMPTOM: FUEL ODOR FROM EVAP CANISTER IS STRONG.
1. CHECK EVAP CANISTER
1. Remove EVAP canister with EVAP canister vent control valve and EVAP control system pressure sensor
attached.
2. Weigh the EVAP canister with EVAP canister vent control valve and EVAP control system pressure sensor
attached.
The weight should be less than 2.0 kg (4.4 lb).
OK or NG
OK >> GO TO 2.
NG >> GO TO 3.
2. CHECK IF EVAP CANISTER SATURATED WITH WATER
Does water drain from the EVAP canister (1)?

EVAP canister vent control valve (2)
Ye s o r N o
Ye s > > G O T O 3 .
No >> GO TO 5.
3. REPLACE EVAP CANISTER
Replace EVAP canister with a new one.
>> GO TO 4.
4. DETECT MALFUNCTIONING PART
Check the EVAP hose between EVAP canister and vehicle frame for clogging or poor connection.
>> Repair or replace EVAP hose.
5. CHECK REFUELING EVAP VAPOR CUT VALVE
Refer to EC-751, "
Component Inspection" .
OK or NG
OK >>INSPECTION END
NG >> Replace refueling EVAP vapor cut valve with fuel tank.
PBIB2731E

EC-750
[VK45DE]
ON BOARD REFUELING VAPOR RECOVERY (ORVR)
Revision: 2007 April2007 M35/M45
SYMPTOM: CANNOT REFUEL/FUEL ODOR FROM THE FUEL FILLER OPENING IS STRONG
WHILE REFUELING.
1. CHECK EVAP CANISTER
1. Remove EVAP canister with EVAP canister vent control valve and EVAP control system pressure sensor
attached.
2. Weigh the EVAP canister with EVAP canister vent control valve and EVAP control system pressure sensor
attached.
The weight should be less than 2.0 kg (4.4 lb).
OK or NG
OK >> GO TO 2.
NG >> GO TO 3.
2. CHECK IF EVAP CANISTER SATURATED WITH WATER
Does water drain from the EVAP canister (1)?

EVAP canister vent control valve (2)
Ye s o r N o
Yes >> GO TO 3.
No >> GO TO 5.
3. REPLACE EVAP CANISTER
Replace EVAP canister with a new one.
>> GO TO 4.
4. DETECT MALFUNCTIONING PART
Check the EVAP hose between EVAP canister and vehicle frame for clogging or poor connection.
>> Repair or replace EVAP hose.
5. CHECK VENT HOSES AND VENT TUBES
Check hoses and tubes between EVAP canister and refueling control valve for clogging, kink, looseness and
improper connection.
OK or NG
OK >> GO TO 6.
NG >> Repair or replace hoses and tubes.
6. CHECK FILLER NECK TUBE
Check recirculation line for clogging, dents and cracks.
OK or NG
OK >> GO TO 7.
NG >> Replace filler neck tube.
PBIB2731E

EC-756
[VK45DE]
ON BOARD DIAGNOSTIC (OBD) SYSTEM
Revision: 2007 April2007 M35/M45
ON BOARD DIAGNOSTIC (OBD) SYSTEMPFP:00028
IntroductionNBS005A1
The ECM has an on board diagnostic system, which detects malfunctions related to engine sensors or actua-
tors. The ECM also records various emission-related diagnostic information including:
The above information can be checked using procedures listed in the table below.
×: Applicable —: Not applicable
*: When DTC and 1st trip DTC simultaneously appear on the display, they cannot be clearly distinguished from each other.
The malfunction indicator lamp (MIL) on the instrument panel lights up when the same malfunction is detected
in two consecutive trips (Two trip detection logic), or when the ECM enters fail-safe mode. (Refer to EC-800,
"Fail-Safe Chart" .)
Two Trip Detection LogicNBS005A2
When a malfunction is detected for the first time, 1st trip DTC and 1st trip Freeze Frame data are stored in the
ECM memory. The MIL will not light up at this stage. <1st trip>
If the same malfunction is detected again during the next drive, the DTC and Freeze Frame data are stored in
the ECM memory, and the MIL lights up. The MIL lights up at the same time when the DTC is stored. <2nd
trip> The “trip” in the “Two Trip Detection Logic” means a driving mode in which self-diagnosis is performed
during vehicle operation. Specific on board diagnostic items will cause the ECM to light up or blink the MIL,
and store DTC and Freeze Frame data, even in the 1st trip, as shown below.
×: Applicable —: Not applicable
When there is an open circuit on MIL circuit, the ECM cannot warn the driver by lighting up MIL when there is
malfunction on engine control system.
Emission-related diagnostic information Diagnostic service
Diagnostic Trouble Code (DTC) Service $03 of SAE J1979
Freeze Frame data Service $02 of SAE J1979
System Readiness Test (SRT) code Service $01 of SAE J1979
1st Trip Diagnostic Trouble Code (1st Trip DTC) Service $07 of SAE J1979
1st Trip Freeze Frame data
Test values and Test limits Service $06 of SAE J1979
Calibration ID Service $09 of SAE J1979
DTC 1st trip DTCFreeze
Frame data1st trip Freeze
Frame dataSRT code SRT status Test value
CONSULT-II×× × × × ×—
GST×× ×—×××
ECM××*— — —×—
ItemsMIL DTC 1st trip DTC
1st trip 2nd trip
1st trip
displaying2nd trip
displaying1st trip
displaying2nd trip
display-
ing BlinkingLighting
upBlinkingLighting
up
Misfire (Possible three way cata-
lyst damage) — DTC: P0300 -
P0308 is being detected×———— —×—
Misfire (Possible three way cata-
lyst damage) — DTC: P0300 -
P0308 is being detected——×——×——
One trip detection diagnoses
(Refer to EC-757, "
EMISSION-
RELATED DIAGNOSTIC INFOR-
MATION ITEMS" .)—×——×———
Except above — — —×—××—

ON BOARD DIAGNOSTIC (OBD) SYSTEM
EC-757
[VK45DE]
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: 2007 April2007 M35/M45
Therefore, when electrical controlled throttle and part of ECM related diagnoses are continuously detected as
NG for 5 trips, ECM warns the driver that engine control system malfunctions and MIL circuit is open by means
of operating fail-safe function.
The fail-safe function also operates when above diagnoses except MIL circuit are detected and demands the
driver to repair the malfunction.
Emission-Related Diagnostic InformationNBS005A3
EMISSION-RELATED DIAGNOSTIC INFORMATION ITEMS
×:Applicable —: Not applicable Engine operating condition in fail-safe mode Engine speed will not rise more than 2,500 rpm due to the fuel cut
Items
(CONSULT-II screen terms)DTC*
1
SRT codeTest value/
Test limit
(GST only)Trip MILReference
page CONSULT-II
GST*
2ECM*3
CAN COMM CIRCUIT U1000
1000*4—— 1×EC-865
CAN COMM CIRCUIT U1001
1001*4— — 1 or 2 —EC-865
CONTROL UNIT(CAN) U1010 1010 — — 1×EC-868
NO DTC IS DETECTED.
FURTHER TESTING
MAY BE REQUIRED.P0000 0000———
Flashing*8—
INT/V TIM CONT-B1 P0011 0011 — — 2×EC-870
INT/V TIM CONT-B2 P0021 0021 — — 2×EC-870
A/F SEN1 HTR (B1) P0031 0031 —×2×EC-883
A/F SEN1 HTR (B1) P0032 0032 —×2×EC-883
HO2S2 HTR (B1) P0037 0037 —×2×EC-890
HO2S2 HTR (B1) P0038 0038 —×2×EC-890
A/F SEN1 HTR (B2) P0051 0051 —×2×EC-883
A/F SEN1 HTR (B2) P0052 0052 —×2×EC-883
HO2S2 HTR (B2) P0057 0057 —×2×EC-890
HO2S2 HTR (B2) P0058 0058 —×2×EC-890
INT/V TIM V/CIR-B1 P0075 0075 — — 2×EC-899
INT/V TIM V/CIR-B2 P0081 0081 — — 2×EC-899
MAF SEN/CIRCUIT P0101 0101 — — 2×EC-906
MAF SEN/CIRCUIT P0102 0102 — — 1×EC-915
MAF SEN/CIRCUIT P0103 0103 — — 1×EC-915
IAT SEN/CIRCUIT P0112 0112 — — 2×EC-922
IAT SEN/CIRCUIT P0113 0113 — — 2×EC-922
ECT SEN/CIRC P0117 0117 — — 1×EC-926
ECT SEN/CIRC P0118 0118 — — 1×EC-926
TP SEN 2/CIRC P0122 0122 — — 1×EC-932
TP SEN 2/CIRC P0123 0123 — — 1×EC-932
ECT SENSOR P0125 0125 — — 2×EC-939
IAT SENSOR P0127 0127 — — 2×EC-942
THERMSTAT FNCTN P0128 0128 — — 2×EC-945
A/F SENSOR1 (B1) P0130 0130 —×2×EC-947
A/F SENSOR1 (B1) P0131 0131 —×2×EC-957
A/F SENSOR1 (B1) P0132 0132 —×2×EC-966
A/F SENSOR1 (B1) P0133 0133××2×EC-975
HO2S2 (B1) P0137 0137××2×EC-987

EC-758
[VK45DE]
ON BOARD DIAGNOSTIC (OBD) SYSTEM
Revision: 2007 April2007 M35/M45
HO2S2 (B1) P0138 0138××2×EC-998
HO2S2 (B1) P0139 0139××2×EC-1011
A/F SENSOR1 (B2) P0150 0150 —×2×EC-947
A/F SENSOR1 (B2) P0151 0151 —×2×EC-957
A/F SENSOR1 (B2) P0152 0152 —×2×EC-966
A/F SENSOR1 (B2) P0153 0153××2×EC-975
HO2S2 (B2) P0157 0157××2×EC-987
HO2S2 (B2) P0158 0158××2×EC-998
HO2S2 (B2) P0159 0159××2×EC-1011
FUEL SYS-LEAN-B1 P0171 0171 — — 2×EC-1022
FUEL SYS-RICH-B1 P0172 0172 — — 2×EC-1033
FUEL SYS-LEAN-B2 P0174 0174 — — 2×EC-1022
FUEL SYS-RICH-B2 P0175 0175 — — 2×EC-1033
FTT SENSOR P0181 0181 — — 2×EC-1043
FTT SEN/CIRCUIT P0182 0182 — — 2×EC-1049
FTT SEN/CIRCUIT P0183 0183 — — 2×EC-1049
TP SEN 1/CIRC P0222 0222 — — 1×EC-1054
TP SEN 1/CIRC P0223 0223 — — 1×EC-1054
MULTI CYL MISFIRE P0300 0300 — — 2×EC-1061
CYL 1 MISFIRE P0301 0301 — — 2×EC-1061
CYL 2 MISFIRE P0302 0302 — — 2×EC-1061
CYL 3 MISFIRE P0303 0303 — — 2×EC-1061
CYL 4 MISFIRE P0304 0304 — — 2×EC-1061
CYL 5 MISFIRE P0305 0305 — — 2×EC-1061
CYL 6 MISFIRE P0306 0306 — — 2×EC-1061
CYL 7 MISFIRE P0307 0307 — — 2×EC-1061
CYL 8 MISFIRE P0308 0308 — — 2×EC-1061
KNOCK SEN/CIRC-B1 P0327 0327 — — 2 —EC-1070
KNOCK SEN/CIRC-B1 P0328 0328 — — 2 —EC-1070
KNOCK SEN/CIRC-B2 P0332 0332 — — 2 —EC-1070
KNOCK SEN/CIRC-B2 P0333 0333 — — 2 —EC-1070
CKP SEN/CIRCUIT P0335 0335 — — 2×EC-1075
CMP SEN/CIRC-B1 P0340 0340 — — 2×EC-1082
TW CATALYST SYS-B1 P0420 0420××2×EC-1089
TW CATALYST SYS-B2 P0430 0430××2×EC-1089
EVAP PURG FLOW/MON P0441 0441××2×EC-1095
EVAP SMALL LEAK P0442 0442××2×EC-1100
PURG VOLUME CONT/V P0443 0443 — — 2×EC-1108
PURG VOLUME CONT/V P0444 0444 — — 2×E C - 111 6
PURG VOLUME CONT/V P0445 0445 — — 2×E C - 111 6
VENT CONTROL VALVE P0447 0447 — — 2×EC-1123
VENT CONTROL VALVE P0448 0448 — — 2×EC-1130
Items
(CONSULT-II screen terms)DTC*
1
SRT codeTest value/
Te s t l i m i t
(GST only)Trip MILReference
page CONSULT-II
GST*
2ECM*3