seat memory INFINITI M35 2007 Factory Service Manual

AV-238
[WITH MOBILE ENTERTAINMENT SYSTEM]
DIAGNOSIS SYSTEM
Revision: 2007 April2007 M35/M45
ITM: AV (NAVI) control unit
NOTE:
??? indicates “UNKWN”.
HANDSFREE PHONE
Handsfree Volume Adjustment
The received volume adjustment of hands-free phone can be
adjusted to Low, Medium, and High settings.
Voice Microphone Test
When this function is turned ON, the voice that is input to microphone is output to front speaker via TEL voice
signal line. The microphone and TEL voice signal line can be checked.
Delete Handsfree Memory
Erase the memory related to the hands-free phone.
REAR DISPLAY

Tilt angle (90 to 135 degrees, 105 to 135 degrees) of rear seat
display can be set.

The automatic retraction of rear seat display can be set.
C Rx (RrSeatSW-ITM) OK /??? 0 - 40
C Rx (Audio-ITM) OK /??? 0 - 40
C Rx (Amp-ITM) OK /??? 0 - 40
C Rx (RearCamera-ITM) OK /??? 0 - 40
C Rx (DVD-ITM) OK /??? 0 - 40
C Rx (Video DIST-ITM) OK /??? 0 - 40
C Rx (Remote Cont-ITM) OK /??? 0 - 40
C Rx (Amp-Audio) OK /??? 0 - 40
C Rx (DVD-Audio) OK /??? 0 - 40ItemsStatus
(Current)Counter
(Past)
SKIB3668E
SKIB3693E

BRC-1
BRAKE CONTROL SYSTEM
F BRAKES
CONTENTS
C
D
E
G
H
I
J
K
L
M
SECTION BRC
A
B
BRC
Revision: 2007 April2007 M35/M45
BRAKE CONTROL SYSTEM
VDC/TCS/ABS
PRECAUTIONS .......................................................... 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 3
Precautions for Procedures without Cowl Top Cover ..... 3
Precautions for Brake System .................................. 3
Precautions for Brake Control .................................. 4
PREPARATION ........................................................... 5
Special Service Tools ............................................... 5
Commercial Service Tools ........................................ 5
ON-VEHICLE SERVICE ............................................. 6
Adjustment of Steering Angle Sensor Neutral Posi-
tion ........................................................................... 6
SYSTEM DESCRIPTION ............................................ 7
System Diagram ....................................................... 7
Functions .................................................................. 7
ABS ....................................................................... 7
EBD ....................................................................... 7
TCS ....................................................................... 8
VDC ....................................................................... 8
ECD ....................................................................... 8
Operation That Is Not "System Error" ...................... 8
ABS ....................................................................... 8
TCS ....................................................................... 8
VDC ....................................................................... 8
Hydraulic Circuit Diagram ........................................ 9
CAN Communication ................................................ 9
SYSTEM DESCRIPTION ...................................... 9
TROUBLE DIAGNOSIS ............................................ 10
Fail-Safe Function .................................................. 10
ABS, EBD SYSTEM ............................................ 10
VDC/TCS ............................................................ 10
How to Perform Trouble Diagnoses ....................... 10
BASIC CONCEPT ............................................... 10
DIAGNOSIS FLOW CHART ................................ 11
ASKING COMPLAINTS ...................................... 12
EXAMPLE OF DIAGNOSIS WORKSHEET ........ 12
Component Parts Location ..................................... 13
Schematic .............................................................. 14Wiring Diagram — VDC — ..................................... 15
Control Unit Input/Output Signal Standard ............. 21
REFERENCE VALUE FROM CONSULT-II ......... 21
CONSULT-II Functions (ABS) ................................ 23
CONSULT-II MAIN FUNCTION ........................... 23
CONSULT-II SETTING PROCEDURE ................ 23
Self-Diagnosis ........................................................ 24
OPERATION PROCEDURE ................................ 24
ERASE MEMORY ............................................... 24
DISPLAY ITEM LIST ........................................... 25
Data Monitor ........................................................... 28
OPERATION PROCEDURE ................................ 28
DISPLAY ITEM LIST ........................................... 28
Active Test .............................................................. 30
OPERATION PROCEDURE ................................ 30
TEST ITEMS ....................................................... 31
For Fast and Accurate Diagnosis ........................... 32
PRECAUTIONS FOR DIAGNOSIS ..................... 32
Basic Inspection ..................................................... 33
BASIC INSPECTION 1: BRAKE FLUID LEVEL,
LEAK INSPECTION AND BRAKE PAD .............. 33
BASIC INSPECTION 2: LOOSENESS OF
POWER SYSTEM TERMINALS AND BATTERY ... 33
BASIC INSPECTION 3: ABS WARNING LAMP,
BRAKE WARNING LAMP, VDC OFF INDICATOR
LAMP AND SLIP INDICATOR LAMP .................. 33
TROUBLE DIAGNOSIS FOR SYSTEM .................... 34
Wheel Sensor Circuit .............................................. 34
INSPECTION PROCEDURE .............................. 34
Engine System ....................................................... 36
INSPECTION PROCEDURE .............................. 36
ABS Actuator and Electric Unit (Control Unit) ........ 36
INSPECTION PROCEDURE .............................. 36
ABS Actuator and Electric Unit (Control Unit) Power
Supply and Ground Circuit ..................................... 37
INSPECTION PROCEDURE .............................. 37
ABS Motor and Motor Relay Circuit ........................ 38
INSPECTION PROCEDURE .............................. 38
Solenoid, VDC Change-Over Valve and Actuator
Relay Circuit ........................................................... 39

EI-34
DOOR FINISHER
Revision: 2007 April2007 M35/M45
DOOR FINISHERPFP:80900
Removal and InstallationNIS0024U
FRONT AND REAR DOOR FINISHER
Removal
1. Fully open door window.
2. Remove inside handle escutcheon and remove screw.
3. Remove arm rest finisher.
4. Remove screw of armrest finisher portion.
1. Inside handle escutcheon 2. Armrest finisher 3. Front door finisher
4. Rear door finisher 5. Step lamp 6. Seat memory switch
7. Front door sash cover inner 8. Rear door sash cover inner
Clip Metal clip
PIIB4931E

DOOR FINISHER
EI-35
C
D
E
F
G
H
J
K
L
MA
B
EI
Revision: 2007 April2007 M35/M45
5. Insert a thin screwdriver from the armrest finisher opening and
lift the lock of the power window switch harness connector.
6. Insert a clip clamp remover into clips on back door finisher, and
disengage clips.
CAUTION:
Insert a clip clamp remover into the part shown by the
arrow (between the clips and the body side panel). Remove
door finisher.
7. Disconnect harness connector for step lamp.
8. Pull up door finisher and pull out toward vehicle inside, and then
disconnect inside handle cable and lock knob cable from back
door finisher.
9. Disconnect harness connector for power window switch, seat memory switch.
10. Remove door finisher.
11. Remove the following parts after removing door finisher.

Inside handle assembly

Armrest

Seat memory switch

Power window switch

Ste p l am p
Installation
Install in the reverse order of removal.
CAUTION:
When installing door finisher, make sure that clips are securely fitted in panel holes on body, and then
press them in.
PIIB4936E
PIIB4932E
PIIB4933E

GW-2Revision: 2007 April2007 M35/M45 SIDE WINDOW GLASS ............................................ 57
Removal and Installation ........................................ 57
REMOVAL ........................................................... 57
INSTALLATION .................................................... 58
REAR WINDOW GLASS AND MOLDING ................ 59
Removal and Installation ........................................ 59
REMOVAL ........................................................... 59
INSTALLATION .................................................... 60
FRONT DOOR GLASS AND REGULATOR ............. 61
Removal and Installation ........................................ 61
DOOR GLASS ..................................................... 61
REGULATOR ASSEMBLY .................................. 62
Disassembly and Assembly .................................... 63
REGULATOR ASSEMBLY .................................. 63
Inspection after Installation ..................................... 63
SYSTEM INITIALIZATION ................................... 63
INSPECT THE FUNCTION OF THE ANTI-
PINCH SYSTEM. ................................................. 63
FITTING INSPECTION ........................................ 64
REAR DOOR GLASS AND REGULATOR ............... 65
Removal and Installation ........................................ 65
DOOR GLASS ..................................................... 65
REGULATOR ASSEMBLY .................................. 66
Disassembly and Assembly .................................... 68
REGULATOR ASSEMBLY .................................. 68
Inspection after Installation ..................................... 68
SYSTEM INITIALIZATION ................................... 68
INSPECT THE FUNCTION OF THE ANTI-
PINCH SYSTEM .................................................. 68
FITTING INSPECTION ........................................ 68
INSIDE MIRROR ....................................................... 69
Wiring Diagram –I/MIRR– ....................................... 69
Removal and Installation ........................................ 70
REMOVAL ........................................................... 70
INSTALLATION .................................................... 70
REAR WINDOW DEFOGGER .................................. 71
Component Parts and Harness Connector Location ... 71
System Description ................................................. 71
CAN Communication System Description .............. 73
CAN Communication Unit ....................................... 73
Schematic ............................................................... 74
Wiring Diagram — DEF — ..................................... 75
Terminal and Reference Value for BCM ................. 80
Terminal and Reference Value for IPDM E/R ......... 80
CONSULT-II Function (BCM) .................................. 81
CONSULT-II START PROCEDURE .................... 81
DATA MONITOR .................................................. 81
ACTIVE TEST ..................................................... 81
CONSULT-II Function (IPDM E/R) .......................... 81
CONSULT-II START PROCEDURE .................... 81
DATA MONITOR .................................................. 81ACTIVE TEST ...................................................... 81
Work Flow ............................................................... 82
Trouble Diagnoses Symptom Chart ........................ 82
Check BCM Power Supply and Ground Circuit ...... 83
Check Rear Window Defogger Switch Circuit ......... 84
Check Rear Window Defogger Power Supply Cir-
cuit .......................................................................... 84
Check Rear Window Defogger Circuit .................... 86
Check Door Mirror Defogger Power Supply Circuit ... 87
Check Driver Side Door Mirror Defogger Circuit ..... 89
Check Passenger Side Door Mirror Defogger Circuit
... 90
Check Filament ....................................................... 92
Filament Repair ....................................................... 92
REPAIR EQUIPMENT ......................................... 92
REPAIRING PROCEDURE ................................. 93
REVERSE INTERLOCK DOOR MIRROR SYSTEM ... 94
Component Parts and Harness Connector Location ... 94
System Description ................................................. 94
OPERATION CONDITIONS ................................ 94
MIRROR UNGLE MEMORY FUNCTION ............ 94
REVERSE INTERLOCK DOOR MIRROR SYS-
TEM OPERATION ............................................... 95
CAN Communication System Description .............. 95
CAN Communication Unit ....................................... 95
Schematic ............................................................... 96
Wiring Diagram — MIRROR — .............................. 97
Terminals and Reference Values for Automatic
Drive Positioner Control Unit .................................103
Terminals and Reference Values for Driver Seat
Control Unit ...........................................................104
CONSULT-II Function (AUTO DRIVE POS.) ........105
CONSULT-II START PROCEDURE ...................105
DATA MONITOR ................................................105
ACTIVE TEST ....................................................105
Work Flow .............................................................106
Symptom Chart .....................................................106
Check Changeover Switch Circuit ........................107
Check Mirror Switch Circuit ...................................109
Check Mirror Motor Circuit .................................... 111
Check Mirror Sensor Circuit ..................................114
Check A/T Control Device R Position Circuit ........117
DOOR MIRROR .......................................................118
Automatic Drive Positioner Interlocking Door Mirror .118
Removal and Installation .......................................118
REMOVAL ..........................................................118
INSTALLATION ..................................................118
Disassembly and Assembly ..................................119
DISASSEMBLY ..................................................119
ASSEMBLY ........................................................120

GW-94
REVERSE INTERLOCK DOOR MIRROR SYSTEM
Revision: 2007 April2007 M35/M45
REVERSE INTERLOCK DOOR MIRROR SYSTEMPFP:28548
Component Parts and Harness Connector LocationNIS00230
System DescriptionNIS00231
Select one of the door mirror faces by change over switch, and then set the selected mirror face downward/
inward.
This operation is synchronized with the R position operation of A/T control device.
OPERATION CONDITIONS

Ignition switch : ON

Changeover switch : Select either left or right

A/T control device : R position
During the reverse interlock door mirror system, if all of the above conditions are not satisfied, mirror face
returns to original angle.
MIRROR UNGLE MEMORY FUNCTION

During the reverse interlock door mirror operation, the mirror angle can be changed. After adjustment, the
mirror face positions can be memorized (2 positions). For memory setting, Refer to SE-12, "
MEMORY
OPERATION"

Initial setting is downward 7°, inward 1° (both of left and right)
Power supplied at all times

through 50A fusible link (letter F, located in the fuse block and fusible link)

to automatic drive positioner control unit terminal 39 and

to driver seat control unit terminal 33.
PIIB6099E
1. Fuse block (J/B) 2. Fusible link 3.Door mirror remote control switch
M95
4. TCM (A/T assembly) F42 5.Automatic drive positioner control
unit M6, M7 (view with the instra-
ment lower panel LH removed)6. Driver seat control unit B204, B205

REVERSE INTERLOCK DOOR MIRROR SYSTEM
GW-105
C
D
E
F
G
H
J
K
L
MA
B
GW
Revision: 2007 April2007 M35/M45
CONSULT-II Function (AUTO DRIVE POS.)NIS00238
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
*1: For setting automatic drive positioner functions only.
*2: During vehicle driving, do not perform active test.
CONSULT-II START PROCEDURE
Refer to GI-38, "CONSULT-II Start Procedure"
DATA MONITOR
Selection from Menu
ACTIVE TEST
CAUTION:
During vehicle driving, do not perform active test.
NOTE:
If active test is performed, reset seat memory and key fob interlock drive positioner after performing work.
CONSULT-II
diagnosis
itemsInspection item, self-diagnosis mode Content Refer to page
AUTO DRIVE
POSITIONERWORK SUPPORT*
1Changes the setting for each function.SE-39
SELF–DIG RESULTS Check the self-diagnosis results.SE-37
DATA MONITOR Selection from menuDisplays the input data to driver seat control
unit and automatic driving positioned control
unit on real-time basis.SE-38
CAN DIAGNOSTIC SUPPORT MONITORThe results of transmit / receive diagnosis of
CAN communication can be readLAN-13
ACTIVE TEST*2Gives a drive signal to a load to check the
operation.SE-39
DRIVER SEAT CONTROL UNIT PART NUMBER Displays driver seat control unit part No. —
Monitor item [OPERATION or UNIT] Contents
MIR CON SW–UP “ON/OFF”ON/OFF status judged from the door mirror remote control switch (UP) signal is
displayed.
MIR CON SW–DN “ON/OFF”ON/OFF status judged from the door mirror remote control switch (DOWN) signal
is displayed.
MIR CON SW–RH “ON/OFF”ON/OFF status judged from the door mirror remote control switch (RIGHT) signal
is displayed.
MIR CON SW–LH “ON/OFF”ON/OFF status judged from the door mirror remote control switch (LEFT) signal s
displayed.
MIR CHNG SW–R “ON/OFF”ON/OFF status judged from the door mirror remote control switch (switching to
RIGHT) signal is displayed.
MIR CHNG SW–L “ON/OFF”ON/OFF status judged from the door mirror remote control switch (switching to
LEFT) signal is displayed.
SET SW “ON/OFF” ON/OFF status judged from the setting switch signal is displayed.
MEMORY SW1 “ON/OFF” ON/OFF status judged from the seat memory switch 1 signal is displayed.
MEMORY SW2 “ON/OFF” ON/OFF status judged from the seat memory switch 2 signal is displayed.
MIR/SE RH R–L “V” Voltage output from RH door mirror sensor (LH/RH) is displayed.
MIR/SE RH U–D “V” Voltage output from RH door mirror sensor (UP/DOWN) is displayed.
MIR/SE LH R–L “V” Voltage output from LH door mirror sensor (LH/RH) is displayed.
MIR/SE LH U–D “V” Voltage output from LH door mirror sensor (UP/DOWN) is displayed.

SE-1
SEAT
I BODY
CONTENTS
C
D
E
F
G
H
J
K
L
M
SECTION SE
A
B
SE
Revision: 2007 April2007 M35/M45
SEAT
PRECAUTIONS .......................................................... 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 3
Service Notice .......................................................... 3
Precautions for Work ................................................ 3
PREPARATION ........................................................... 4
Special Service Tools ............................................... 4
Commercial Service Tools ........................................ 4
SQUEAK AND RATTLE TROUBLE DIAGNOSES ..... 5
Work Flow ................................................................ 5
CUSTOMER INTERVIEW ..................................... 5
DUPLICATE THE NOISE AND TEST DRIVE ....... 6
CHECK RELATED SERVICE BULLETINS ........... 6
LOCATE THE NOISE AND IDENTIFY THE
ROOT CAUSE ...................................................... 6
REPAIR THE CAUSE ........................................... 6
CONFIRM THE REPAIR ....................................... 7
Generic Squeak and Rattle Troubleshooting ........... 7
INSTRUMENT PANEL .......................................... 7
CENTER CONSOLE ............................................. 7
DOORS ................................................................. 7
TRUNK .................................................................. 8
SUNROOF/HEADLINING ..................................... 8
SEATS ................................................................... 8
UNDERHOOD ....................................................... 8
Diagnostic Worksheet .............................................. 9
AUTOMATIC DRIVE POSITIONER ...........................11
Component Parts And Harness Connector Location
.... 11
System Description ................................................ 12
MANUAL OPERATION ....................................... 12
MEMORY OPERATION ...................................... 12
EXITING OPERATION ........................................ 14
ENTRY OPERATION .......................................... 14
INTELLIGENT KEY INTERLOCK OPERATION ... 15
FAIL-SAFE MODE .............................................. 15
INITIALIZATION PROCEDURE .......................... 16
SETTING CHANGE FUNCTION ......................... 16
CAN Communication System Description .............. 16CAN Communication Unit ....................................... 16
Schematic ............................................................... 17
Wiring Diagram — AUT/DP — ............................... 19
Terminals and Reference Values for BCM .............. 31
Terminals and Reference Value for Intelligent Key
Unit ......................................................................... 31
Terminals and Reference Values for Driver Seat
Control Unit ............................................................. 32
Terminals and Reference Values for Automatic
Drive Positioner Control Unit .................................. 34
CONSULT-II Function (AUTO DRIVE POS.) .......... 37
CONSULT-II START PROCEDURE .................... 37
SELF-DIAGNOSIS RESULTS ............................. 37
DATA MONITOR ................................................. 38
ACTIVE TEST ..................................................... 39
WORK SUPPORT ............................................... 39
Work Flow ............................................................... 40
Symptom Chart ....................................................... 40
CAN Communication Inspection Using CONSULT-
II (Self-Diagnosis) ................................................... 42
Check BCM Power Supply and Ground Circuit ...... 42
Check Driver Seat Control Unit Power Supply and
Ground Circuit ........................................................ 43
Check Automatic Drive Positioner Control Unit
Power Supply and Ground Circuit .......................... 44
Check Sliding Motor Circuit .................................... 45
Check Reclining Motor Circuit ................................ 46
Check Front Lifting Motor Circuit ............................ 47
Check Rear Lifting Motor Circuit ............................. 49
Check Telescopic Motor Circuit .............................. 50
Check Tilt Motor Circuit .......................................... 51
Check Sliding Sensor Circuit .................................. 53
Check Reclining Sensor Circuit .............................. 55
Check Front Lifting Sensor Circuit .......................... 57
Check Rear Lifting Sensor Circuit .......................... 59
Check Telescopic Sensor Circuit ............................ 61
Check Tilt Sensor Circuit ........................................ 63
Check Door Mirror Sensor LH Circuit ..................... 64
Check Door Mirror Sensor RH Circuit .................... 67
Check Sliding Switch Circuit ................................... 69

SE-2Revision: 2007 April2007 M35/M45 Check Reclining Switch Circuit ............................... 71
Check Lifting Switch (Front) Circuit ........................ 73
Check Lifting Switch (Rear) Circuit ......................... 75
Check Power Seat Switch Ground Circuit .............. 76
Check Telescopic Switch Circuit ............................. 77
Check Tilt Switch Circuit ......................................... 79
Check Seat Memory and Set Switch Circuit ........... 81
Check Seat Memory Indicator Lamp Circuit ........... 82
Check Door Mirror Sensor Power Supply and
Ground Circuit ........................................................ 84
Check A/T Device (Detention Switch) Circuit ......... 86
Check Front Door Switch (Driver Side) Circuit ....... 87
Check UART Communication Line Circuit .............. 88
Check Lumbar Support Circuit ............................... 90
POWER SEAT(PASSENGER SIDE) ......................... 92
Schematic ............................................................... 92
Wiring Diagram — SEAT — .................................... 93
POWER SEAT(REAR) .............................................. 96
Component Parts and Harness Connector Location ... 96
System Description ................................................. 96
REAR POWER SEAT LH AND RH OPERATION ... 96
REAR SEAT RETREAT FUNCTION ................... 97
Schematic ............................................................... 98
Wiring Diagram — R/SEAT — ................................ 99
Terminals and Reference Values for Rear Seat Con-
trol Unit .................................................................103
Work Flow .............................................................104
Trouble Diagnoses Symptom Chart ......................104
Check Rear Power Seat Power Supply Circuit .....104
Check Rear Seat Control Unit Power Supply and
Ground Circuit ......................................................105
Check Rear Seat Sliding Motor Circuit .................106
Check Rear Power Seat Switch Circuit ................107
Check Automatic Return Cancel Switch Circuit ....109
Check Automatic Return Cancel Switch ...............110
Check Rear Door Switch Circuit ............................111
Check Rear Seat Sliding Sensor Circuit ...............112
CLIMATE CONTROLLED SEAT .............................114
Component Parts and Harness Connector Location .114
System Description ...............................................114
Schematic .............................................................118
Wiring Diagram — C/SEAT — ..............................119
Terminal and Reference Value for Climate Con-
trolled Seat Control Unit .......................................124
Work Flow .............................................................125
Trouble Diagnoses Symptom Chart ......................126
Preliminary Check ................................................126
Check Climate Controlled Seat Control Unit Power
Supply Circuit .......................................................127
Check Climate Controlled Seat Control Unit Power
Supply and Ground Circuit ...................................128
Check Climate Controlled Seat Switch Power Sup-ply Circuit ..............................................................131
Check Climate Controlled Seat Switch Circuit ......132
Check Climate Controlled Seat Switch Indicator Cir-
cuit ........................................................................134
Check Seat Cushion Thermal Electric Device Cir-
cuit ........................................................................136
Check Seatback Thermal Electric Device Circuit ..137
Check Seat Cushion Thermal Electric Device Sen-
sor Circuit ..............................................................138
Check Seatback Thermal Electric Device Sensor
Circuit ....................................................................140
Check Climate Controlled Seat Blower Motor Circuit .141
Check Climate Controlled Seat Control Unit .........143
HEATED SEAT ........................................................144
Component Parts and Harness Connector Location .144
System Description ...............................................144
Schematic .............................................................146
Wiring Diagram — HSEAT — ...............................147
Terminals and Reference Values for Rear Seat Con-
trol Unit ..................................................................152
Work Flow .............................................................152
Trouble Diagnoses Symptom Chart ......................152
Check Rear Heated Seat Power Supply and Ground
Circuit ....................................................................153
Check Rear Seat Control Unit Power Supply and
Ground Circuit .......................................................154
Check Rear Heated Seat Switch Circuit ...............156
Check Rear Heated Seat Indicator Power Supply
Circuit ....................................................................158
Check Rear Heated Seat Indicator Circuit ............159
Check Rear Heated Seat Circuit ...........................161
Check Rear Seatback Heater Circuit ....................162
FRONT SEAT ..........................................................164
Driver's Seat Components ....................................164
Passenger's Seat Components .............................166
Removal and Installation .......................................168
REMOVAL ..........................................................168
INSTALLATION ..................................................168
Disassembly and Assembly ..................................169
SEATBACK ........................................................169
SEAT CUSHION ................................................170
CLIMATE CONTROLLED SEAT ........................172
REAR SEAT .............................................................173
Bench Seat Components ......................................173
Power Seat (Split Type) Components ...................175
Removal and Installation .......................................177
BENCH SEAT ....................................................177
POWER SEAT ...................................................177
Disassembly and Assembly ..................................178
BENCH SEAT ....................................................178
POWER SEAT ...................................................180

AUTOMATIC DRIVE POSITIONER
SE-11
C
D
E
F
G
H
J
K
L
MA
B
SE
Revision: 2007 April2007 M35/M45
AUTOMATIC DRIVE POSITIONERPFP:28491
Component Parts And Harness Connector LocationNIS0025Q
PIIB6292E
1. Fuse block (J/B) 2. Fuse and fusible link box 3. BCM M1, M2, M3
(View with the glove box assembly
removed)
4. A. Automatic drive positioner control
unit M6, M7
B. Telescopic motor M45
C. Telescopic sensor M44
D. Tilt sensor M37
E. Tilt motor M36
(View with the driver lower panel
removed)5. A. Front lifting motor B209
B. Rear lifting motor B210
C. Driver seat control unit
B204,B205
D. Sliding motor B2076. Seat memory switch D9
7. A. Lumbar support switch B212
B. Reclining switch B213
C. Sliding/Lifting switch B2138. A. ADP steering switch M46
B. Key slot M14
C. Door mirror control switch M959. Reclining motor B208