lights INFINITI Q60 CONVERTIBLE 2014 Quick Reference Guide

01
07
06
02
03
04
05
4
first drive features
INFINITI Intelligent Key System
The INFINITI Intelligent Key system allows you to lock or
unlock the vehicle, open the trunk and start the engine.
It is important to make sure the Intelligent Key is
with you (that is, in your pocket or purse).
The operating range of the Intelligent Key is within
31.5 in (80 cm) from each request switch.
To lock the vehicle, push either door handle request
switch
01 once or press the
button
02 on the key fob.
To unlock the vehicle, perform one of the following procedures:



•

Push either door handle request switch 01 once; the

corresponding door will unlock. Push the door handle
request switch
01 again within 1 minute; all other doors

will unlock, or



•


Press the
button
03 on the key fob to unlock the driver’s

side door. Press the
button again; all other doors will unlock.
To release the trunk lid, press the hOLD button
04 for more than

1 second. Lift the trunk lid to access the trunk.
To retract the hard top (Convertible models), push and hold the
door handle request switch
01 until the hard top is fully open.
The Intelligent Key can also be used to activate the panic alarm by pres\
sing and holding the

button
05 for more than 1 second. Once activated, the panic alarm and headlights w\
ill
stay on for a period of time.
INFINITI INTELLIGENT KE
y BATTER y DISCHARGE
If the battery in the Intelligent Key is almost
discharged, the guide light
06 of the Intelligent

Key port blinks and the Intelligent Key battery
discharge indicator
07 is displayed in the vehicle

information display.
To start the engine under these circumstances, insert
the Intelligent Key into the key port with the buttons
facing upward and the key ring end toward you until
it latches into place. Then push the ignition switch to
start the engine.
To remove the Intelligent Key from the port, push the
ignition switch to turn the engine off and then pull the
Intelligent Key out of the port.
The Intelligent Key port does not charge the Intelligent Key battery. If\
you see the low battery
indicator
07 , replace the battery in the Intelligent Key.
Do not insert the mechanical key or any other objects into the key port \
because it will

damage the key port.
For more information, refer to the “Pre-driving checks and adjustments (section 3)”, the “Starting and driving (section 5)” and the
“Maintenance and do-it yourself (section 8)” of your Owner’s Manual.
1276473_14a_Q60_Convertible_QRG_062113.indd 46/21/13 3:31 PM

8
first drive features
Headlight Control Switch
HEADLIGHT CONTROL
Turn the headlight control switch to the
position 01 to turn on the front parking, side

marker, tail, license plate and instrument panel
lights. Turn the switch to the position

02 to turn on
the headlights.
AUTOLIGHT S
y
STEM
The autolight system will automatically turn the headlights on when it i\
s dark and off when
it is light. The system will keep the headlights on for a period of time\
after you turn the
ignition off and all doors are closed.
To activate the autolight system, turn the headlight control switch to t\
he AU t O position
03
then push the ignition switch to ON. To deactivate the autolight system, turn the headlight
control switch to the OFF,
01 or
position
02 .
HIGH BEAM SELECT
Push the headlight control switch forward 04 to
select the high beam function. The blue indicator
light
illuminates in the instrument panel. Pull
the headlight switch back to the original position to
select the low beam. The blue indicator light goes off.
Pull and release the headlight control switch 05 to

flash the headlight high beams on and off.
FOG LIGHT SWITCH
The headlights must be in the auto, or the low
beams
selected for the fog lights to operate.
Turn the switch (inside collar) to the
position
06
to turn the fog lights on.
Turn the switch (inside collar) to the
OFF position to
turn the fog lights off.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
03
01
02
04
05
06
1276473_14a_Q60_Convertible_QRG_062113.indd 86/21/13 3:31 PM

13
Intelligent Cruise Control (ICC) System (if so equipped)
VEHICLE-TO-VEHICLE DISTANCE CONTROL MODE
To set Vehicle-To-Vehicle Distance Control mode,
press the ON/OFF button

01 for less than 1.5 seconds.

The C
r
UISE indicator light
02 will illuminate.
Accelerate to the desired speed.
Push down on the
COAS t /SE t switch
03 and release

it. Cruise control will be set to the desired speed.
Press the distance button 04 repeatedly to change

the set distance between long, middle, and short.
When a vehicle is not detected ahead of you in the
lane, the set distance and set vehicle speed indicator
lights will illuminate
05 in set mode.
When a vehicle is detected ahead of you in the lane,

the vehicle ahead detection, set distance, and set
vehicle speed indicator lights will illuminate
06 in

set mode.
To reset at a faster cruising speed, push up and hold the ACCEL/ r ES
switch
07 . When the vehicle attains the desired speed, release the switch.
To reset at a slower cruising speed, push down and hold the
COAS t /SE t
switch
03 . Release the switch when the vehicle slows to the desired speed.

To cancel the preset speed, push the CANCEL switch
08 or tap the brake pedal. The set
vehicle speed indicator 05 will go out.
To turn off cruise control, press the
ON/OFF button
01 . The C r UISE indicator light
02 ,
in the instrument panel will turn off.
To set conventional (fixed speed) cruise control mode:
While cruise control is off, press the ON/OFF
button
01 and hold it down for more than 1.5
seconds. The C
r
UISE indicator light will illuminate.
Accelerate to the desired speed.
Push down on the
COAS t /SE t switch and release it. The SE t indicator light will illuminate.
Cruise control should be set to the desired speed.
To switch between the two cruise control modes:
When one of the two cruise modes is in use, you must turn the system off\
, and then turn it
on again to select the other cruise control mode.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
04
0807
03
01
0205
06
1276473_14a_Q60_Convertible_QRG_062113.indd 136/21/13 3:31 PM

21
HomeLink® Universal Transceiver
The HomeLink® system can learn and consolidate the functions of up to 3 different
hand-held transmitters, operating items such as garage doors, property g\
ates, outdoor and
indoor lights or alarm systems.
To program the Homelink® Universal Transceiver:



•


Position the handheld transceiver 1-3 in (26-76 mm) away from the Home\
link® surface,
keeping the Homelink® indicator light in view.



•


Press and hold the desired Homelink® button and the handheld transmitter button
simultaneously until the Homelink® indicator light flashes slowly and then rapidly.



•


Both buttons may be released when the indicator light flashes rapidly.
To verify the programing is complete, press and hold the Homelink® and observe the
indicator light:



•


A solid continuous light indicates the programing is complete and the Ho\
melink®
button will activate your device.



•


A blinking light that turns to a solid continuous light after 2 seconds \
indicates
additional steps are required to complete the programing.
An additional person may make the remaining steps easier. To complete th\
e
programing process:



•

At the receiver of the device that you are programing to the Homelink®, press and
release the “learn” or “smart” button (the name may vary by\
manufacturer but it is
usually located near where the hanging antenna wire is attached to the u\
nit).
y ou have
approximately 30 seconds to initiate the following step.



•


Press and hold the programmed Homelink® button for 2 seconds and release.
Repeat the previous 2 steps up to 3 times to complete the programming pr\
ocess.
Homelink® should now activate your device.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual, the HomeLink® website at
www.homelink.com or call 1-800-355-3515.
HOMELINK®
1276473_14a_Q60_Convertible_QRG_062113.indd 216/21/13 3:32 PM