run flat INFINITI Q60 COUPE 2017 Owner's Manual
[x] Cancel search | Manufacturer: INFINITI, Model Year: 2017, Model line: Q60 COUPE, Model: INFINITI Q60 COUPE 2017Pages: 482, PDF Size: 8.26 MB
Page 7 of 482
NOTE:
The compressor tire pressure gauge may
show a pressure reading of 87 psi (600 kPa)
for about 30 seconds while inflating the
tire. The pressure gauge is indicating the
pressure inside the sealant can. When the
sealant has been injected into the tire the
pressure gauge will drop and indicate ac-
tual tire pressure.
WARNING
●To avoid serious personal injury while
using the emergency tire puncture re-
pair kit:
– Securely tighten the compressor hose to the tire valve. Failure to do so
can cause the sealant to spray into
the air and get into your eyes or on
the skin.
● Do not stand directly beside the dam-
aged tire while it is being inflated be-
cause of the risk of the rupture. If there
are any cracks or bumps, turn the com-
pressor off immediately. If the tire pressure does not increase to
26 psi
(180 kPa) within 10 minutes, the tire may be
seriously damaged and the tire cannot be re-
paired with this tire puncture repair kit. It is
recommended you visit an INFINITI retailer for
servicing.
7. When the tire pressure is at the specified amount, turn the air compressor off. If the
pressure cannot be inflated to the specified
amount, the air compressor can be turned
off at the minimum of 26 psi (180 kPa) .
Remove the power plug from the power
outlet and quickly remove the hose from the
tire valve. Attach the protective cap and
valve cap. Properly stow the emergency tire
puncture repair kit in the trunk.
CAUTION
To avoid serious personal injury when
stowing the emergency tire puncture re-
pair kit:
●Keep the sealant bottle screwed into
the compressor. Failure to do so can
cause the sealant to spray into the air
and get into your eyes or on the skin. 8. Immediately drive the vehicle for 10 minutes
or 2 miles (3 km) at a speed of 50 MPH
(80 km/h) or less.
9. After driving, make sure that the air com- pressor switch is in the OFF (O) position,
then screw the hose securely onto the tire
valve. Check the tire pressure with the pres-
sure gauge. The temporary repair is com-
pleted if the tire pressure does not drop.
Make sure the pressure is adjusted to the
pressure that is specified on the tire and
loading information label before driving.
10. If the tire pressure drops, repeat the steps from 5 to 9. If the pressure drops again or
under 19 psi (130 kPa) , the tire cannot be
repaired with this tire puncture repair
kit. It is recommended you visit an INFINITI
retailer for this servicing.
The sealant bottle and hose cannot be re-
used to repair another punctured tire. It is
recommended you visit an INFINITI retailer
to purchase replacements.
Page 9 of 482
SIZECOLD
TIRE IN-
FLATION PRES-SURE
REAR
ORIGINAL TIRE P255/
40RF19
96V
240 kPa,
35 PSI
265/
35RF19
94W 240 kPa,
35 PSI
245/
40RF19
94W 240 kPa,
35 PSI
P245/
40RF19
94V 240 kPa,
35 PSI
SPARE
TIRE (if so equipped) T145/
70R18
107M
420 kPa,
60 PSI
CAUTION
Tire chains/cables should not be installed
on P255/40RF19 and 265/35RF19 tires.
Doing so will cause damage to the vehicle.
If you plan to use tire chains/cables, you
should install 245/40RF19 or
P245/40RF19 tires on your vehicle.
Use of tire chains may be prohibited according to
location. Check the local laws before installing
tire chains. When installing tire chains, make sure
they are the proper size for the tires on your
vehicle and are installed according to the chain
manufacturer’s suggestions. Use only SAE
class S chains. Class “S” chains are used on
vehicles with restricted tire to vehicle clearance.
Vehicles that can use Class “S” chains are de-
signed to meet the SAE standard minimum clear-
ances between the tire and the closest vehicle
suspension or body component required to ac-
commodate the use of a winter traction device
(tire chains or cables) . The minimum clearances
are determined using the factory equipped tire
size. Other types may damage your vehicle. Use
chain tensioners when recommended by the tire
chain manufacturer to ensure a tight fit. Loose
end links of the tire chain must be secured or
removed to prevent the possibility of whipping
action damage to the fenders or underbody. If
possible, avoid fully loading your vehicle when using tire chains. In addition, drive at a reduced
speed. Otherwise, your vehicle may be damaged
and/or vehicle handling and performance may be
adversely affected.
Tire chains must be installed only on the
rear wheels and not on the front wheels.
Never install tire chains on a TEMPORARY USE
ONLY spare tire (if so equipped) . Never install tire
chains on a punctured run-flat tire (if so
equipped) , as this could damage your vehicle.
Do not use tire chains on dry roads. Driving with
tire chains in such conditions can cause damage
to the various mechanisms of the vehicle due to
some overstress.
TIRE CHAINS