ignition INFINITI Q60 COUPE 2019 Quick Reference Guide

8
Wiper and Washer Switch
Move the lever up or down to one of the following
positions to operate the windshield wipers:
MIST
One sw

eep operation
OFF

Wipers ar

e OFF
AUTO

Speed-sensing and r
ain-sensing



(if

so equipped) automatic wipe
LO



C

ontinuous wipe, slow
HI

C

ontinuous wipe, fast
To adjust the wiper sensitivity for the AUTO setting, twist
the control ring
.
Pull the lever
toward you to operate the
windshield washer.
WIPER BLADE REPLACEMENT PROCEDURE
The windshield wipers must be in the service position
in order to replace the wiper blades.
To move the wiper blades to the service position:
•


When the ignition swit
ch is in the ON position or
within 60 seconds of placing the ignition switch
in the OFF position, lift the windshield wiper and
washer lever upwards twice in less than 0.5 seconds.
The windshield wipers will move to the service
position automatically, and the wiper blades can
now be replaced.
To move the wiper blades back to the original position:


•
Plac
e the wiper arm in the down position and lift the wiper and washer lever up for
more than 1 second, or lower the lever down to operate at any wiper speed.
To turn the rain sensor function on and off:
1.


Pr
ess the MENU button below the lower display.
2.


T
ouch the “Settings” key and then the “Vehicle”
key
on the display.
3

.



T

ouch the “Rain Sensor” key
to toggle the
feature ON and OFF.
When the rain-sensing function is disabled, the AUTO
position on the wiper stalk will work in conventional
intermittent mode.
Please see your Owner’s Manual for important safety information, system limitations, and additional operating and feature information.

16
HomeLink® Universal Transceiver
(if so equipped)
HomeLink
To program the HomeLink® Universal Transceiver:


1 .

P

osition the handheld transceiver 1-3 in (26-76 mm)
away from the HomeLink surface, keeping the HomeLink
indicator light in view.


2 .

Pr

ess and hold the desired HomeLink button and the handheld
transmitter button simultaneously until the HomeLink indicator
light flashes slowly and then rapidly.
3

.



Bo

th buttons may now be released.


4

Pr

ess and hold the HomeLink button, and a blinking light that
turns to a solid, continuous light after 2 seconds will display.


5 .

A

t the receiver of the device press and release the program
button (this button can typically be found near the hanging
antenna wire of the device you are programing into HomeLink).
6.


Pr

ess and hold the programed HomeLink button for 2
seconds and release.
Please see your Owner’s Manual for important safety information, system limitations, and
additional operating and feature information.
REMOTE ENGINE START
(if so equipped)
The r

emote engine start system must be
enabled in the vehicle settings within the
lower display. To start your vehicle remotely:
1.


Pr
ess the lock button
to
lock the vehicle.
2.


Pr

ess and hold the remote start button
within 5 seconds of pressing the lock
button
and the engine will start.
T

o start driving, depress the brake
pedal and press the ignition switch
START/STOP button.
State laws may apply, review local
laws before using.
ROLL DOWN FEATURE
The windows can be opened remotely using your Infiniti Intelligent Key.
•


With the

vehicle unlocked, press and hold the unlock button
to
open the windows and moonroof (if so equipped) remotely.
•


I

f the unlock button
is released, the windows will stop.
To resume the roll down feature, press and hold the unlock
button
again.Please see your Owner’s Manual for important safety information, system limitations, and
additional operating and feature information.
Infiniti Intelligent Key System