check engine light INFINITI Q70 2014 Owner's Guide

Black plate (402,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
5-100Starting and driving
all times.
. As there is a performance limit to the
Preview Function, never rely solely on
this system. This system does not
correct careless inattentive or absent-
minded driving, or overcome poor visi-
bility in rain, fog, or other bad weather.
Reduce vehicle speed by depressing the
brake pedal, in order to maintain a safe
distance between vehicles.
. The system may not detect the vehicle in
front of you in certain road or weather
conditions. The Preview Function may
not operate properly under the following
conditions. The vehicle is still driveable
under normal conditions and the Brake
Assist will operate.
—When rain, snow or dirt adhere to
the system sensor
—When strong light (for example, atsunrise or sunset) is directly shining
on the front of the vehicle
—Winding or hilly roads may causethe sensor to temporarily not detect
a vehicle in the same lane or may
detect objects or vehicles in other
lanes.
—Vehicle position in the lane maycause the sensor to temporarily not
detect a vehicle in the same lane or
may detect objects or vehicles in
other lanes.
SSD0471
Warning light and displayY51D-V-E01-DB5ED500-4C68-479F-9197-379EA1E778CDWhen the Preview Function is not operating
properly, a chime sounds and the system
warning light (orange) will come on.
Action to take:
GUID-CA441E56-2FD0-4540-A74C-DB510E9F7AE0If the warning light comes on, park the
vehicle in a safe place. Turn the engine off,
restart the engine and resume driving.
If the indicator stays on, it may indicate
that the Preview Function is malfunction-
ing (the brake is operative). Although the
Vehicle is still driveable under normal
conditions, have the vehicle checked at
an INFINITI retailer.
Condition:

Black plate (404,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
5-102Starting and driving
WARNING
Do not pump the brake pedal. Doing so may
result in increased stopping distances.
Self-test featureY51D-V-E01-9FAB00BB-F2BE-4168-BD75-236754B398C1The ABS includes electronic sensors, elec-
tric pumps, hydraulic solenoids and a
computer. The computer has a built-in
diagnostic feature that tests the system
each time you start the engine and move
the vehicle at a low speed in forward or
reverse. When the self-test occurs, you may
hear a“clunk” noise and/or feel a pulsa-
tion in the brake pedal. This is normal and
does not indicate a malfunction. If the
computer senses a malfunction, it switches
the ABS off and illuminates the ABS
warning light on the instrument panel.
The brake system then operates normally,
but without anti-lock assistance.
If the ABS warning light illuminates during
the self-test or while driving, have the
vehicle checked by an INFINITI retailer.
Normal operationY51D-V-E01-97EC20E5-32E3-4D14-80B0-197E7EAA54F0The ABS operates at speeds above 3 to 6
MPH (5 to 10 km/h).
When the ABS senses that one or more
wheels are close to locking up, the actuator
rapidly applies and releases hydraulic
pressure. This action is similar to pumping
the brakes very quickly. You may feel a
pulsation in the brake pedal and hear a
noise from under the hood or feel a
vibration from the actuator when it is
operating. This is normal and indicates
that the ABS is operating properly. How-
ever, the pulsation may indicate that road
conditions are hazardous and extra care is
required while driving.
Y51D-V-E01-4A9596A2-6386-4C22-A04D-18A64B158580The Vehicle Dynamic Control (VDC) system
uses various sensors to monitor driver
inputs and vehicle motion. Under certain
driving conditions, the VDC system helps
to perform the following functions.
. Controls brake pressure to reduce
wheel slip on one slipping drive wheel
so power is transferred to a non
slipping drive wheel on the same axle.
. Controls brake pressure and engine
output to reduce drive wheel slip based
on vehicle speed (traction control func-
tion).
. Controls brake pressure at individual
wheels and engine output to help the
driver maintain control of the vehicle in
the following conditions:
— understeer (vehicle tends to not
follow the steered path despite
increased steering input)
— oversteer (vehicle tends to spin due
to certain road or driving condi-
tions).
The VDC system can help the driver to
maintain control of the vehicle, but it
cannot prevent loss of vehicle control in
all driving situations.
When the VDC system operates, the VDC
warning light
in the instrument panel
VEHICLE DYNAMIC CONTROL (VDC) SYSTEM
Condition:

Black plate (413,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
Y51D-V-E01-63E297C5-4018-4F40-92EF-3B211665C34BTo shut off the engine in an emergency
situation while driving, perform the follow-
ing procedure:
.Rapidly push the push-button ignition
switch 3 consecutive times in less than
1.5 seconds, or
. Push and hold the push-button ignition
switch for more than 2 seconds.Y51D-V-E01-6C3D919A-CD26-4BC0-9CF9-2EC5F910E687
TIRE PRESSURE MONITORING SYS-
TEM (TPMS)
Y51D-V-E01-BFEA3614-E51F-4536-91BF-65C5324E7C3EThis vehicle is equipped with the Tire
Pressure Monitoring System (TPMS). It
monitors tire pressure of all tires except
the spare. When the low tire pressure
warning light is lit and the CHECK TIRE
PRESSURE warning appears in the dot
matrix liquid crystal display, one or more
of your tires is significantly under-inflated.
If the vehicle is being driven with low tire
pressure, the TPMS will activate and warn
you of it by the low tire pressure warning
light. This system will activate only when
the vehicle is driven at speeds above 16
MPH (25 km/h). For more details, see
“Warning/indicator lights and audible re-
minders” (P.2-10) and “Tire Pressure Mon-
itoring System (TPMS)” (P.5-4).
WARNING
.If the low tire pressure warning light
illuminates or LOW PRESSURE informa-
tion is displayed on the monitor screen
while driving, avoid sudden steering
maneuvers or abrupt braking, reduce
vehicle speed, pull off the road to a safe
location and stop the vehicle as soon as possible. Driving with under-inflated
tires may permanently damage the tires
and increase the likelihood of tire fail-
ure. Serious vehicle damage could occur
and may lead to an accident and could
result in serious personal injury. Check
the tire pressure for all four tires. Adjust
the tire pressure to the recommended
COLD tire pressure shown on the Tire
and Loading Information label to turn
the low tire pressure warning light OFF. If
the light still illuminates while driving
after adjusting the tire pressure, a tire
may be flat. If you have a flat tire,
replace it with a spare tire as soon as
possible.
. When a spare tire is mounted or a wheel
is replaced, the TPMS will not function
and the low tire pressure warning light
will flash for approximately 1 minute.
The light will remain on after 1 minute.
Contact your INFINITI retailer as soon as
possible for tire replacement and/or
system resetting.
. Replacing tires with those not originally
specified by INFINITI could affect the
proper operation of the TPMS.
. Do not inject any tire liquid or aerosol
tire sealant into the tires, as this may
In case of emergency6-3
EMERGENCY ENGINE SHUT OFF FLAT TIRE
Condition:

Black plate (439,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
8 Maintenance and do-it-yourself
Maintenance requirement...
.................................... 8-2
Scheduled maintenance ...
.................................. 8-2
General maintenance ...
....................................... 8-2
Where to go for service ...
................................... 8-2
General maintenance ...
........................................... 8-2
Explanation of maintenance items ...
................... 8-2
Maintenance precautions ...
..................................... 8-5
Engine compartment check locations ...
................... 8-7
VK56VD engine ...
............................................... 8-7
VQ37VHR engine ...
............................................. 8-9
Engine cooling system ...
....................................... 8-12
Checking engine coolant level ...
....................... 8-13
Changing engine coolant ...
............................... 8-14
Engine oil ...
.......................................................... 8-14
Checking engine oil level ...
............................... 8-15
Changing engine oil and filter ...
....................... 8-15
Automatic transmission fluid ...
............................. 8-18
Power steering fluid ...
........................................... 8-18
Brake fluid ...
......................................................... 8-19
Brake fluid ...
.................................................... 8-19
Window washer fluid ...
......................................... 8-19
Battery ...
.............................................................. 8-20
Jump starting ...
................................................ 8-22
Variable voltage control system ...
......................... 8-22 Drive belts
...
........................................................ 8-22
Spark plugs ...
...................................................... 8-23
Replacing spark plugs ...
................................. 8-23
Air cleaner ...
........................................................ 8-24
Windshield wiper blades ...
................................... 8-25
Cleaning ...
...................................................... 8-25
Replacing ...
..................................................... 8-26
Brakes ...
.............................................................. 8-27
Self-adjusting brakes ...
................................... 8-27
Brake pad wear warning ...
.............................. 8-27
Fuses ...
................................................................ 8-28
Engine compartment ...
.................................... 8-28
Passenger compartment ...
............................... 8-29
Intelligent Key battery replacement ...
................... 8-30
Lights ...
................................................................ 8-33
Headlights ...
................................................... 8-33
Exterior and interior lights ...
........................... 8-34
Wheels and tires ...
............................................... 8-36
Tire pressure ...
............................................... 8-36
Tire labeling ...
................................................ 8-40
Types of tires ...
............................................... 8-42
Tire chains ...
................................................... 8-43
Changing wheels and tires ...
........................... 8-43
Condition:

Black plate (442,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
8-4Maintenance and do-it-yourself
securely. Check the belt webbing for cuts,
fraying, wear or damage.
Seats:Check seat position controls such as
seat adjusters, seatback recliner, etc. to
ensure they operate smoothly and that all
latches lock securely in every position.
Check that the head restraints move up
and down smoothly and that the locks (if
so equipped) hold securely in all latched
positions.
Steering wheel: Check for changes in the
steering conditions, such as excessive free
play, hard steering or strange noises.
Warning lights and chimes: Make sure that
all warning lights and chimes are operating
properly.
Windshield defroster: Check that the air
comes out of the defroster outlets properly
and in sufficient quantity when operating
the heater or air conditioner.
Windshield wiper and washer*: Check that
the wipers and washer operate properly
and that the wipers do not streak.
Under the hood and vehicleY51D-V-E01-B3361551-A047-4A72-ACCF-65F901F88160The maintenance items listed here should
be checked periodically (for example, each
time you check the engine oil or refuel). Battery*:
Check the fluid level in each cell.
It should be between the MAX and MIN
lines. Vehicles operated in high tempera-
tures or under severe condition require
frequent checks of the battery fluid level.
NOTE:
Care should be taken to avoid situations
that can lead to potential battery dis-
charge and potential no-start conditions
such as:
1. Installation or extended use of electro-
nic accessories that consume battery
power when the engine is not running
(Phone chargers, GPS, DVD players,
etc.)
2. Vehicle is not driven regularly and/or
only driven short distances.
In these cases, the battery may need to be
charged to maintain battery health.
Brake fluid level*: Make sure that the
brake fluid level is between the MAX and
MIN lines on the reservoir.
Engine coolant level*: Check the coolant
level when the engine is cold.
Engine drive belts*: Make sure that no belt
is frayed, worn, cracked or oily.
Engine oil level*: Check the level after parking the vehicle on a level spot and
turning off the engine. Wait more than 15
minutes for the oil to drain back into the oil
pan.
Exhaust system:
Make sure there are no
loose supports, cracks or holes. If the
sound of the exhaust seems unusual or
there is a smell of exhaust fumes, im-
mediately have the exhaust system in-
spected by an INFINITI retailer. (See
“Precautions when starting and driving”
(P.5-3) for exhaust gas (Carbon monoxide).)
Fluid leaks: Check under the vehicle for
fuel, oil, water or other fluid leaks after the
vehicle has been parked for a while. Water
dripping from the air conditioner after use
is normal. If you should notice any leaks or
if gasoline fumes are evident, check for the
cause and have it corrected immediately.
Power steering fluid level* and lines:
Check the level when the fluid is cold,
with the engine off. Check the lines for
proper attachment, leaks, cracks, etc.
Radiator and hoses: Check the front of the
radiator and clean off any dirt, insects,
leaves, etc., that may have accumulated.
Make sure the hoses have no cracks,
deformation, rot or loose connections.
Condition:

Black plate (455,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
engine. Failure to do so could lead to engine
damage.
6. Coat the gasket on the new filter withclean engine oil.
7. Screw in the oil filter clockwise until a slight resistance is felt, then tighten
additionally more than 2/3 turn.
Oil filter tightening torque:11 to 15 ft-lb
(14.7 to 20.5 N·m)
8. Clean and re-install the drain plug with a new washer. Securely tighten the
drain plug with a wrench.
Drain plug tightening torque:22 to 29 ft-lb
(29 to 39 N·m)
Do not use excessive force.
9. Refill engine with recommended oil and install the oil filler cap securely.
CAUTION
The dipstick must be inserted in place to
prevent oil spillage from the dipstick hole
while filling the engine with oil.
See “Capacities and recommended fuel/lubricants”
(P.9-2) for drain and
refill capacity. The drain and refill
capacity depends on the oil tempera-
ture and drain time. Use these specifi-
cations for reference only. Always use
the dipstick to determine the proper
amount of oil in the engine.
10. Start the engine and check for leakage around the drain plug and the oil filter.
Correct as required.
11. Turn the engine off and wait more than 15 minutes. Check the oil level with the
dipstick. Add engine oil if necessary.
After the operationY51D-V-E01-790CC92C-2688-443C-80B6-74DD163C016F1.Install the engine undercover into
position as the following steps.
a. Pull the center of the small plastic
clip out.
b. Hold the engine undercover into position.
c. Insert the clip through the under- cover into the hole in the frame, then
push the center of the clip in to lock
the clip in place.
d. Install the other bolts that hold the undercover in place. Be careful not
to strip the bolts or over-tighten them.
2. Lower the vehicle carefully to the
ground.
3. Dispose of waste oil and filter properly.
WARNING
. Prolonged and repeated contact with
used engine oil may cause skin cancer.
. Try to avoid direct skin contact with used
oil. If skin contact is made, wash
thoroughly with soap or hand cleaner
as soon as possible.
. Keep used engine oil out of reach of
children.
Maintenance and do-it-yourself8-17
Condition:

Black plate (466,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
8-28Maintenance and do-it-yourself
Y51D-V-E01-29097B28-1FE0-4182-A485-A2047D0C5A2D
SDI2584
SDI2566
ENGINE COMPARTMENTY51D-V-E01-AFE79579-EF18-4DDE-B356-BDC18538EFB0
CAUTION
Never use a fuse of a higher or lower
amperage rating than that specified on the
fuse box cover. This could damage the
electrical system or cause a fire.
If any electrical equipment does not
operate, check for an open fuse.
1. Be sure the ignition switch is pushed tothe OFF or LOCK position and the
headlight switch is turned to OFF.
2. Open the engine hood and remove the cover on the battery and the fuse/
fusible link holder.
3. Remove the fuse/fusible link holder
cover.
4. Remove the fuse with the fuse puller.
SDI1754
5. If the fuse is open*A, replace it with a
new fuse
*B. Spare fuses are stored in
the passenger compartment fuse box.
6. If a new fuse also opens, have the electrical system checked and repaired
by an INFINITI retailer.
The holder
*1also contains the fuses. For
checking and/or replacing, see an INFINITI
retailer.
Fusible linksY51D-V-E01-3E721E86-CD62-4D57-8D17-0637DAF969EFIf any electrical equipment does not
operate and fuses are in good condition,
check the fusible links. If any of these
fusible links are melted, replace only with
FUSES
Condition:

Black plate (492,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
9-6Technical and consumer information
above symptoms are encountered, have
your vehicle checked at an INFINITI retailer
or other competent service facility.
However, now and then you may notice
light spark knock for a short time while
accelerating or driving up hills. This is no
cause for concern, because you get the
greatest fuel benefit when there is light
spark knock for a short time under heavy
engine load.
JVT0159X
1.API certification mark
2.API service symbol
ENGINE OIL AND OIL FILTER RE-
COMMENDATION
Y51D-V-E01-D3E5E26B-FC22-4D68-908C-7DA80DA562C9
Selecting the correct oilY51D-V-E01-7FE27830-3B20-44C8-B50F-C4B29604F170It is essential to choose the correct grade,
quality, and viscosity engine oil to ensure
satisfactory engine life and performance,
see“Capacities and recommended fuel/
lubricants” (P.9-2). INFINITI recommends
the use of an energy conserving oil in
order to improve fuel economy.
Select only engine oils that meet the American Petroleum Institute (API) certifi-
cation or International Lubricant Standar-
dization and Approval Committee (ILSAC)
certification and SAE viscosity standard.
These oils have the API certification mark
on the front of the container. Oils which do
not have the specified quality label should
not be used as they could cause engine
damage.
Oil additivesY51D-V-E01-66B343FB-CACE-4D63-BB72-E04A44C2B684INFINITI does not recommend the use of oil
additives. The use of an oil additive is not
necessary when the proper oil type is used
and maintenance intervals are followed.
Condition:

Black plate (508,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
9-22Technical and consumer information
online at:
https://wwwapps.tc.gc.ca/Saf-Sec-
Sur/7/PCDB-BDPP/Index.aspx.
Additional information concerning
motor vehicle safety may be obtained
from Transport Canada’s Road Safety
Information Centre at 1-800- 333-
0371 or online at www.tc.gc.ca/
roadsafety (English speakers) or
www.tc.gc.ca/securiteroutiere
(French speakers).
To notify INFINITI of any safety con-
cerns please contact our Consumer
Information Centre toll free at 1-800-
361-4792.
Y51D-V-E01-1566689B-E555-4824-98F9-8466E02C8EE3A vehicle equipped with Intelligent All-
Wheel Drive (AWD) should never be tested
using a two wheel dynamometer (such as
the dynamometers used by some states for
emissions testing), or similar equipment.
Make sure you inform test facility person-
nel that your vehicle is equipped with AWD
before it is placed on a dynamometer.
Using the wrong test equipment may result
in transmission damage or unexpected
vehicle movement which could result in
serious vehicle damage or personal injury.
Due to legal requirements in some states/
areas, your vehicle may be required to be
in what is called the“ready condition”for
an Inspection/Maintenance (I/M) test of
the emission control system.
The vehicle is set to the “ready condition”
when it is driven through certain driving
patterns. Usually, the “ready condition”
can be obtained by ordinary usage of the
vehicle.
If a powertrain system component is
repaired or the battery is disconnected,
the vehicle may be reset to a “not ready
condition”. Before taking the I/M test,
check the vehicle’s inspection/mainte-
nance test readiness condition. Place the
ignition switch in the ON position without starting the engine. If the Malfunction
Indicator Light (MIL) comes on steady for
20 seconds and then blinks for 10
seconds, the I/M test condition is
“not
ready”. If the MIL does not blink after 20
seconds, the I/M test condition is “ready”.
Contact an INFINITI retailer to set the
“ready condition” or to prepare the vehicle
for testing.
READINESS FOR INSPECTION/
MAINTENANCE (I/M) TEST (US only)
Condition:

Black plate (511,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
10 Index
A
ABS (Anti-lock Braking System)...
....................... 5-101
Active noise control ...
........................................ 5-107
Air bag system Front-seat mounted side-impact
supplemental air bag system ...
....................... 1-48
Roof-mounted curtain side-impact
supplemental air bag system ...
....................... 1-48
Air bag warning labels ...
...................................... 1-51
Air bag warning light ...
............................... 1-51, 2-15
Air cleaner housing filter ...
................................... 8-24
Air conditioner Air conditioner specification label ...
................ 9-13
Air conditioning system refrigerant and
lubricant recommendations ...
............................ 9-7
Automatic climate control ...
............................ 4-34
In-cabin microfilter ...
....................................... 4-48
Air filter In-cabin microfilter ...
....................................... 4-48
Alarm
How to stop alarm (see vehicle
security system) ...
........................................... 2-30
Alcohol, drugs and driving ...
.................................. 5-8
Antenna ...
............................................................ 4-83
Anti-lock Braking System (ABS) ...
....................... 5-101
Appearance care Exterior appearance care ...
................................ 7-2
Interior appearance care ...
................................ 7-4
Armrest ...
............................................................... 1-4
Ashtrays (See cigarette lighter and ashtrays) ...
.... 2-46 Audible reminders
...
............................................ 2-19
Audio operation precautions ...
............................. 4-49
Audio system ...
.................................................... 4-49
Steering wheel audio controls ...
...................... 4-82
Auto closure ...
..................................................... 3-19
Autolight system ...
............................................... 2-35
Automatic Automatic climate control ...
.................. 4-37, 4-41
Automatic transmission fluid (ATF) ...
............... 8-18
Climate control ...
............................................ 4-34
Driving with automatic transmission ...
............ 5-14
Automatic door locks ...
.......................................... 3-5
Automatic drive positioner ...
................................ 3-27
Automatic seat positioner ...
................................. 3-27
Average fuel consumption and speed ...
................ 2-27
Avoiding collision and rollover ...
............................ 5-7
B
Battery ...
.............................................................. 8-20
Battery replacement, Intelligent Key ...
............... 3-2
Battery saver system ...
................................... 2-37
Intelligent Key ...
.............................................. 8-30
Variable voltage control system ...
................... 8-22
Before starting the engine ...
................................ 5-13
Belts (See drive belts) ...
....................................... 8-22
Blind Spot Intervention (BSI) ON
indicator light ...
................................................... 2-16
Bluetooth
®hands-free phone system
(models with navigation system) ...
....................... 4-85 Bluetooth
®hands-free phone system
(models without navigation system) ...
.................. 4-95
Bluetooth
®streaming audio ...
............................. 4-74
Brake Anti-lock Braking System (ABS) ...
.................. 5-101
Brake fluid ...
................................................... 8-19
Brake force distribution ...
............................. 5-103
Brake system ...
............................................... 5-98
Parking brake operation ...
............................... 5-19
Brake warning light ...
........................................... 2-11
Break-in schedule ...
............................................. 5-91
Brightness control Display ON/OFF button ...
................................ 4-10
Bulb check/instrument panel ...
............................ 2-10
Bulb replacement ...
.............................................. 8-33
C
Cabin air filter ...
................................................... 4-48
Capacities and recommended fuel/lubricants ...
...... 9-2
Car phone or CB radio ...
...................................... 4-84
Card holder ...
....................................................... 2-50
Catalytic converter
Three way catalyst ...
......................................... 5-4
CD/CF/USB memory care and cleaning ...
............. 4-81
Center multi-function control panel ...
..................... 4-4
Check tire pressure warning ...
.............................. 2-23
Child restraints ...
................................................. 1-20
LATCH system ...
.............................................. 1-21
Precautions on child restraints ...
..................... 1-20
Condition: