display INFINITI Q70 2014 Owners Manual

Black plate (322,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
5-20Starting and driving
Y51D-V-E01-C0EEA0E7-8281-43A9-B50B-279933178972
SSD1024
Drive mode select switch
Four driving modes can be selected by
using the drive mode selector switch,
STANDARD, SPORT, ECO and SNOW.
NOTE:
. When the drive mode select switch
selects a mode, the mode may not
switch quickly. This is not a malfunc-
tion.
. Select the STANDARD mode for normal
driving.
STANDARD MODEY51D-V-E01-2A69D9CF-8968-4411-B1B1-678B5A8E1A41Recommended for normal driving. Turn the
drive mode select switch to the
position. “STANDARD” appears on the dot
matrix liquid crystal display for 2 seconds.
SPORT MODEY51D-V-E01-12F87C14-3739-48A8-BB8F-4BD7B2C4BCBDAdjusts the engine and transmission
points to enhance performance. If the
vehicle is equipped with the active trace
control system, the amount of brake
control provided by active trace control is
reduced. (See “Vehicle Dynamic Control
(VDC) system” (P.5-102).) Turn the drive
mode select switch to the SPORT position.
“SPORT” appears on the dot matrix liquid
crystal display for 2 seconds.
NOTE:
In the SPORT mode, fuel economy may be
reduced.
SNOW MODEY51D-V-E01-2CF0CF99-743E-4A2F-B896-63241986BC6DUsed on snowy roads or slippery areas.
When the SNOW mode is activated, engine
output is controlled to avoid wheel spin.
Turn the SNOW mode off for normal
driving. Turn the drive mode select switch
to the SNOW position. “SNOW”appears on
the dot matrix liquid crystal display for 2 seconds.
ECO MODEY51D-V-E01-83A58480-0586-4801-B32F-A1E3F28863D3Adjusts engine and transmission points to
enhance fuel economy.
NOTE:
Selecting this drive mode will not neces-
sarily improve fuel economy as many
driving factors influence its effectiveness.
OperationY51D-V-E01-9412D164-939D-4D3B-8652-D9F79E95161CTurn the drive mode select switch to the
ECO position.
“ECO”appears on the dot
matrix liquid crystal display for 2 seconds
and the ECO drive indicator light illumi-
nates on the instrument panel.
When the accelerator pedal is depressed
within the range of economy drive, the ECO
drive indicator light illuminates in green.
When the accelerator pedal is depressed
above the range of economy drive, the
color of the ECO drive indicator light
changes to orange. For ECO pedal system
equipped models see “ECO pedal system”
(P.5-21).
The ECO drive indicator light will not
illuminate in the following cases:
. When the shift lever is in the R (Reverse)
position.
INFINITI DRIVE MODE SELECTOR
Condition:

Black plate (324,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
5-22Starting and driving
SSD0939
SSD1001
Setting ECO pedal reaction force:GUID-CA441E56-2FD0-4540-A74C-DB510E9F7AE01. Push the SETTING*1button and high-
light the ECO DRIVE key on the display
using the INFINITI controller. Then push
the ENTER
*2button.
2. Highlight the ECO pedal key and push the ENTER
*2button.
SSD1025
3. To set the reaction force of the ECOpedal system, highlight “Standard”or
“Soft”.
4. To turn off the ECO pedal system,
highlight the OFF key, select ON and
push the ENTER
*2button. When the
ECO pedal system is tuned off, the
accelerator will operate normally.
Condition:

Black plate (328,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
5-26Starting and driving
SIC4335
Warning systems switch
The warning systems switch is used to turn
on and off the LDW system when it is
activated using the settings menu on the
center display. See “How to enable/disable
the LDW system using the settings menu”
(P.5-27).
When the warning systems switch is turned
off, the indicator
*1on the switch is off.
The indicator will also be off if the LDW, the
Blind Spot Warning (BSW) and the Forward
Collision Warning (FCW) systems are deac-
tivated.
For the BSW and FCW systems, see “Blind
Spot Warning (BSW) system/Blind Spot Intervention
TM(BSI) system”
(P.5-33) and
“Forward Collision Warning (FCW) system”
(P.5-83).
SSD0939
With navigation system
SSD1001
Condition:

Black plate (329,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
How to enable/disable the LDW
system using the settings menu
GUID-5D4D0FCE-7292-4390-BC0D-D7430B968B9APerform the following steps to enable or
disable the LDW system.
1. Push the SETTING
*1button and high-
light the “Driver Assistance” key on the
display using the INFINITI controller.
Then push the ENTER
*2button.
2. Highlight the “Driver Assistance Warn-
ings” key, and push the ENTER
*2
button.
JVS0080X
3. Highlight the “Lane Departure Warning”
key, select ON (enabled) or OFF (dis-
abled) and push the ENTER
*2button.
Temporary disabled status at high
temperature
Y51D-V-E01-0B0A10AE-593E-4626-BBFE-8D84CAD69C22If the vehicle is parked in direct sunlight
under high temperature conditions (over
approximately 1048F (408C) and then
started, the LDW system may be deacti-
vated automatically. The LDW light (orange)
will flash.
When the interior temperature is reduced,
the LDW system will resume operating
automatically and the LDW light (orange) will stop flashing.
LANE DEPARTURE PREVENTION
(LDP) SYSTEM
Y51D-V-E01-FB6B6FAC-AB51-42A2-8866-1B9A38526E24
Precautions on LDP systemY51D-V-E01-AA7B1886-AED0-4152-91F5-D6A9157BE770
WARNING
.
The LDP system will not steer the vehicle
or prevent loss of control. It is the
driver’s responsibility to stay alert, drive
safely, keep the vehicle in the traveling
lane, and be in control of vehicle at all
times.
. The LDP system is primarily intended for
use on well-developed freeways or high-
ways. It may not detect the lane markers
in certain roads, weather or driving
conditions.
. Using the LDP system under some
conditions of road, lane marker or
weather, or when you change lanes
without using the lane change signal
could lead to an unexpected system
operation. In such conditions, you need
to correct the vehicle’s direction with
your steering operation to avoid acci-
dents.
Starting and driving5-27
Condition:

Black plate (332,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
5-30Starting and driving
SSD0938
Dynamic driver assistance switch
The LDP system turns on when the dynamic
driver assistance switch on the steering
wheel is pushed when the “Lane Departure
Prevention” is enabled in the settings
menu on the center display. The LDW light
(green) on the instrument panel illuminates
when the LDP system is turned on.
SSD0939
With navigation system
SSD1001
How to enable/disable the LDP
system using the settings menu
GUID-FBDC2F4D-6267-44BE-AA3B-4567F2E2FBE3Perform the following steps to enable or
disable the LDP system.
1. Push the SETTING
*1button and high-
light the “Driver Assistance” key on the
display using the INFINITI controller.
Then push the ENTER
*2button.
2. Highlight the “Dynamic Assistance Set-
tings” key, and push the ENTER
*2
button.
Condition:

Black plate (337,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
on the brightness of the ambient light.
A chime sounds if the radar sensors have
already detected vehicles when the driver
activates the turn signal. If a vehicle comes
into the detection zone after the driver
activates the turn signal, then only the
BSW/BSI indicator light flashes and no
chime sounds. (See“BSW/BSI driving
situations” (P.5-40).)
SIC4335
Warning systems switch
The warning systems switch is used to turn
on and off the BSW system when it is
activated using the settings menu on the
center display. See “How to enable/disable
the BSW system using the settings menu”
(P.5-36).
When the warning systems switch is turned
off, the indicator
*1on the switch is off.
The indicator will also be off if the BSW, the
Lane Departure Warning (LDW) and the
Forward Collision Warning (FCW) systems
are deactivated.
For the LDW and FCW systems, see “Lane
Departure Warning (LDW) system/Lane Departure Prevention (LDP) system”
(P.5-
23) and “Forward Collision Warning (FCW)
system” (P.5-83).
Starting and driving5-35
Condition:

Black plate (338,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
5-36Starting and driving
SSD0939
With navigation system
SSD1001
How to enable/disable the BSW
system using the settings menu
GUID-450348FF-AE1B-4C34-945D-99612FAF06E1Perform the following steps to enable or
disable the BSW system.
1. Push the SETTING
*1button and high-
light the “Driver Assistance” key on the
display using the INFINITI controller.
Then push the ENTER
*2button.
2. Highlight the “Driver Assistance Warn-
ings” key, and push the ENTER
*2
button.
JVS0080X
3. Highlight the “Blind Spot Warning” key,
select ON (enabled) or OFF (disabled)
and push the ENTER
*2button.
Condition:

Black plate (339,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
SSD1028
BSW/BSI indicator light
SSD1029
BSI ON indicator light (green)
SSD0938
Dynamic driver assistance switch
BSI SYSTEM OPERATIONY51D-V-E01-96B4C4EA-DE72-44A7-840F-25C8167EECC1If the radar sensors detect vehicles in the
detection zone, the BSW/BSI indicator
light located by the outside mirrors illumi-
nates. If your vehicle is approaching a lane
marker, the BSW/BSI indicator light
flashes and an audible warning will sound
three times. Then the system applies the
brakes on one side of the vehicle for a
short period of time to help return the
vehicle back to the center of the lane. BSI
operates regardless of turn signal usage.NOTE:
.
Warning and system application of the
brakes will only be activated if the
BSW/BSI indicator light is already
illuminated when your vehicle ap-
proaches a lane marker. If another
vehicle comes into the detection zone
after your vehicle has crossed a lane
marker, no warning or brake applica-
tion will be activated. (See “BSW/BSI
driving situations” (P.5-40).)
. The BSI system is typically activated
earlier than the Lane Departure Pre-
vention (LDP) system when your vehi-
cle is approaching a lane marker.
The BSI system turns on when the dynamic
driver assistance switch on the steering
wheel is pushed when the “Blind Spot
Intervention” is enabled in the settings
menu on the center display. The BSI ON
indicator light (green) on the instrument
panel illuminates when the BSI system is
turned on.
The BSI system provides an audible warn-
ing and flashes the indicator light when
BSI is activated even if the BSW system is
off.
Starting and driving5-37
Condition:

Black plate (340,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
5-38Starting and driving
SSD0939
With navigation system
SSD1001
How to enable/disable the BSI
system using the settings menu
Y51D-V-E01-7FAF8BCB-7D1B-4C60-8E45-9C397B4F24BFPerform the following steps to enable or
disable the BSI system.
1. Push the SETTING
*1button and high-
light the “Driver Assistance” key on the
display using the INFINITI controller.
Then push the ENTER
*2button.
2. Highlight the “Dynamic Assistance Set-
tings” key, and push the ENTER
*2
button.
SSD1002
3. Highlight the “Blind Spot Intervention”
key, select ON (enabled) or OFF (dis-
abled) and push the ENTER
*2button.
For the LDP and DCA systems, see “Lane
Departure Prevention (LDP) system” (P.5-
27) and “Distance Control Assist (DCA)
system” (P.5-71).
WARNING
.Do not use the BSI system under the
following conditions because the system
may not function properly.
—During bad weather (for example,
Condition:

Black plate (349,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
Y51D-V-E01-23AAF2E8-96D4-4088-8FC4-E0EA618F6140
PRECAUTIONS ON CRUISE CONTROLY51D-V-E01-C80C843B-C941-4617-9A6B-8ACA08B59C74.If the cruise control system malfunc-
tions, it will cancel automatically. The
SET indicator on the dot matrix crystal
display will then blink to warn the
driver.
. If the engine coolant temperature be-
comes excessively high, the cruise
control system will be canceled auto-
matically.
. If the SET indicator blinks, turn the
cruise control main switch off and have
the system checked by your INFINITI
retailer.
. The SET indicator may sometimes blink
when the cruise control main switch is
turned ON while pushing the COAST/
SET, ACCELERATE/RESUME or CANCEL
switch. To properly set the cruise
control system, perform the steps
below in the order indicated.
WARNING
Do not use the cruise control when driving
under the following conditions:
. when it is not possible to keep the
vehicle at a set speed .
in heavy traffic or in traffic that varies in
speed
. on winding or hilly roads
. on slippery roads (rain, snow, ice, etc.)
. in very windy areas
Doing so could cause a loss of vehicle
control and result in an accident.
SSD0941
1. ACCELERATE/RESUME switch
2. COAST/SET switch
3. CANCEL switch
4. MAIN (ON·OFF) switch
CRUISE CONTROL OPERATIONSY51D-V-E01-FB0B9100-C99C-4A9C-A4E2-8F0F55B5FB3CThe cruise control allows driving at a speed
between 25 to 90 MPH (40 to 144 km/h)
without keeping your foot on the accel-
erator pedal.
To turn on the cruise control, push the
MAIN switch on. The CRUISE indicator will
come on.
To set cruising speed, accelerate your
vehicle to the desired speed, push the
Starting and driving5-47
CRUISE CONTROL
Condition: