lights INFINITI Q70 2014 Owner's Manual

Black plate (118,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
2-46Instruments and controls
Y51D-V-E01-42C176E4-70E1-482B-AA1F-4C9A9B43B7C4
SIC4339
The power outlet is located in the center
console.
CAUTION
.The outlet and plug may be hot during or
immediately after use.
. Do not use with accessories that exceed
a 12 volt, 120W (10A) power draw. Do
not use double adapters or more than
one electrical accessory.
. Use power outlet with the engine run-
ning to avoid discharging the vehicle
battery. .
Avoid using power outlet when the air
conditioner, headlights or rear window
defroster is on.
. This power outlet is not designed for use
with a cigarette lighter unit.
. Push the plug in as far as it will go. If
good contact is not made, the plug may
overheat or the internal temperature
fuse may blow.
. Before inserting or disconnecting a plug,
be sure the electrical accessory being
used is turned OFF.
. When not in use, be sure to close the
cap. Do not allow water or any liquid to
contact the outlet.
Y51D-V-E01-C36FC2DF-3FFF-4A46-93E3-4DCE87A48F6E
SIC4340
FRONTY51D-V-E01-C36E4DE5-D906-4CE4-8FCE-3511F799F543To open the ashtray lid, push the lid down
and release it
*1.
To empty the ashtray, pull out
*2.
The cigarette lighter operates when the
ignition switch is in the ON position.
Push the lighter in all the way
*3, then
release it. When the lighter is heated, it will
spring out. Return the lighter to its original
position after use.
POWER OUTLET CIGARETTE LIGHTER AND ASHTRAYS
Condition:

Black plate (123,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
SIC3248
COAT HOOKSY51D-V-E01-6E60A118-4C06-4622-A493-70124199F866The coat hooks are equipped beside the
rear personal lights.
CAUTION
Do not place items which are more than 2 lb
(1 kg) on the hook.
SIC4350
TRUNK HOOKSY51D-V-E01-7F2F2069-5E83-4347-9CDB-726F230769B1
WARNING
.Always make sure that the cargo is
properly secured. Use the suitable ropes
and hooks.
. Unsecured cargo can become dangerous
in an accident or sudden stop.
CAUTION
Do not apply a total load of more than 22 lb
(10 kg) to a single hook.
Instruments and controls2-51
Condition:

Black plate (130,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
2-58Instruments and controls
Y51D-V-E01-597C12A9-9379-411B-9ABA-7239511EFB84
SIC4356
MAP LIGHTSY51D-V-E01-35C4693D-F33B-4099-9E8D-4C1A607B8732Push the button as illustrated to turn the
light on or off.
SIC3250
PERSONAL LIGHTSY51D-V-E01-D9715772-F047-42B5-94C8-E2B65886B291
RearY51D-V-E01-06B0E4ED-D809-4ED0-A432-7C8280E7B38DPush the button as illustrated to turn the
light on or off.
SIC4357
INTERIOR LIGHT CONTROL SWITCHY51D-V-E01-28981B41-A540-466D-853C-8B7908116D1F
*1ON switchY51D-V-E01-F809DC40-1F48-4B4C-A4C1-79026C84F715When the ON switch*1is pushed on, the
map lights and rear personal lights will
illuminate. When the switch is turned off,
the lights will not illuminate, regardless of
the condition.
*2DOOR OFF switchY51D-V-E01-9EC535D6-4F15-4248-98CF-6E94179633A3When the DOOR OFF switch*2is not
pushed on, the map lights and rear
personal lights will illuminate under the
following conditions:
INTERIOR LIGHTS
Condition:

Black plate (131,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
.ignition switch is switched to the OFF
position
— remain on for about 15 seconds.
. doors are unlocked by pushing the
UNLOCK button on the Intelligent Key
or door handle request switch with the
ignition switch in the LOCK position
— remain on for about 15 seconds.
. any door is opened and then closed
with the ignition switch in the LOCK
position
— remain on for about 15 seconds.
. any door is opened
— remain on while the door is opened.
When the door is closed, the lights
go off.
When the DOOR OFF switch
*2is pushed
on, the map and rear personal lights will
not illuminate under the above condition.
The map and rear personal lights can be
turned on only with the ON switch
*1.
The lights will also turn off after a period
of time when the lights remain illuminated
after the ignition switch has been pushed
to the OFF or LOCK position to prevent the
battery from becoming discharged.
When the auto interior illumination is set
to the OFF position (see “Vehicle informa-tion and settings”
(P.4-10)), the lights will
illuminate under the following condition:
. any door is opened with the ignition
switch in any position
— remain on while the door is opened.
When the door is closed, the lights
go off.
CAUTION
Do not use for extended periods of time with
the engine stopped. This could result in a
discharged battery.
Y51D-V-E01-C411E7C5-750B-43CD-8458-695C07891728
SIC3869
The light on the vanity mirror will turn on
when the cover on the vanity mirror is
opened.
When the cover is closed, the light will turn
off.
The lights will also turn off after a period
of time when the lights remain illuminated
to prevent the battery from becoming
discharged.
Instruments and controls2-59
VANITY MIRROR LIGHTS
Condition:

Black plate (150,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
3-14Pre-driving checks and adjustments
Locking doors and fuel-filler doorY51D-V-E01-E9C01606-95CE-4FEE-9BEC-65E3B96B27331. Push the ignition switch to the OFFposition and make sure you carry the
Intelligent Key with you.*1
2. Close all the doors.
3. Push the LOCK
button*1on the
Intelligent Key.
4. All the doors and fuel-filler door will lock.
5. The hazard indicator flashes twice and the horn chirps once.
*1: Doors will lock with the Intelligent Key while the ignition switch is in the ACC
or ON position.
Unlocking doors and fuel-filler doorY51D-V-E01-CACAF5DB-E00C-4137-8A50-620148E048581. Push the UNLOCKbutton*2on the
Intelligent Key once.
2. The hazard indicator flashes once. The driver’s door and fuel-filler door will
unlock.
3. Push the UNLOCK
button on the
Intelligent Key again within 1 minute.
4. The hazard indicator flashes once
again. All the doors will unlock.
All doors will be locked automatically
unless one of the following operations is performed within 1 minute after pushing
the UNLOCK button on the Intelligent Key
while the doors are locked. If during this 1-
minute time period, the UNLOCK button on
the Intelligent Key is pushed, all doors will
be locked automatically after another 1
minute.
.
Opening any door
. Pushing the ignition switch
Opening windowsY51D-V-E01-C312D8D6-DA39-443A-B386-43A24CA3CA9AThe UNLOCKbutton*2operation also
allows you to open the window that is
equipped with the automatic open/close
function. (See “Power windows” (P.2-52).)
To open the window, push the door
UNLOCK
button on the Intelligent Key
for about 3 seconds after the door is
unlocked.
To stop opening, release the UNLOCK
button.
If the window open operation is stopped in
mid-operation while pushing the UNLOCK
button, release and push the UNLOCK
button again until the window opens
completely.
Window cannot be closed using the In-
telligent Key. The door window can also be operated by
turning the mechanical key in a door lock.
(See
“Doors” (P.3-4).)
Opening trunk lidY51D-V-E01-DE9E3776-94FB-4A31-AD24-12EE8E6283111. Push the TRUNKbutton*3on the
Intelligent Key for more than 1 second.
2. The trunk will unlatch.
3. Raise the trunk lid to open the trunk.
If the trunk lid does not unlock, push the
trunk open request switch and manually lift
the trunk lid if:
. there is snow on the trunk lid.
. a heavy object such as rear spoiler is
attached to the trunk lid.
. the trunk lid is frozen.
Using panic alarmY51D-V-E01-C48ED9A1-9FD0-4D97-98ED-384A5E9B57B7If you are near your vehicle and feel
threatened, you may activate the alarm to
call attention as follows:
1. Push the PANIC
button*4on the
key for more than 1 second.
2. The theft warning alarm and headlights will stay on for 25 seconds.
3. The panic alarm stops when:
.It has run for 25 seconds, or
Condition:

Black plate (161,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
Y51D-V-E01-899C7DDA-DD40-4329-80A8-CE6DFE22FD97
SPA2447
INSIDE MIRRORY51D-V-E01-10BF6E9D-94BA-434D-B556-9F6B29EFE1E4Adjust the height and the angle of the
inside mirror to the desired position.
SPA2450
Automatic anti-glare typeY51D-V-E01-544653BF-F3F0-4DF6-B343-B51FC6A721BAThe inside mirror is designed so that it
automatically changes reflection according
to the intensity of the headlights of the
following vehicle.
The anti-glare system will be automatically
turned on when the ignition switch is
pushed to the ON position.
The anti-glare system also operates for the
outside rearview mirrors.
When the anti-glare system is turned on,
the indicator light
*Awill illuminate and
excessive glare from the headlights of the
vehicle behind you will be reduced. Push the
“*”switch
*Cto make the
inside rearview mirror operate normally.
The indicator light will turn off. Push the “I”
switch
*Dto turn the system on.
Do not allow any object to cover the
sensors
*Eor apply glass cleaner on
them. Doing so will reduce the sensitivity
of the sensor, resulting in improper
operation.
For the HomeLink
®Universal Transceiver
operation, see “HomeLink®Universal
Transceiver” (P.2-60).
OUTSIDE MIRRORSY51D-V-E01-0D342898-430F-456A-9040-9578417F2830
WARNING
Objects viewed in the outside mirror on the
passenger side are closer than they appear.
Be careful when moving to the right. Using
only this mirror could cause an accident.
Use the inside mirror or glance over your
shoulder to properly judge distances to
other objects.
Pre-driving checks and adjustments3-25
MIRRORS
Condition:

Black plate (163,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
switch.
4. The outside mirror surface moves
downward.
When one of the following conditions has
occurred, the outside mirror surface will
return to its original position.
. The shift lever is moved to any position
other than R (Reverse).
. The outside mirror control switch is set
to the center position.
. The ignition switch is pushed to the OFF
position.
Automatic anti-glareGUID-91655C78-1391-4C73-AE8D-F7830B95A06EThe outside rearview mirrors are designed
so that its automatically change reflection
according to the intensity of the headlights
of the vehicle following you.
The anti-glare system will be automatically
turned on when you push the ignition
switch to the “ON”position.
SIC3869
VANITY MIRRORY51D-V-E01-9AE2DF89-3765-4965-AB82-63AC485FF71BTo use the front vanity mirror, pull down
the sun visor and pull up the cover.
Y51D-V-E01-E450D796-08F9-4562-8F47-BFC4EB16402BThe automatic drive positioner system has
four features:
.Entry/exit function
. Seat synchronization function
. Memory storage
. Setting memory function
ENTRY/EXIT FUNCTIONY51D-V-E01-34AC63B3-B54E-4551-9D60-0BA261F4A048This system is designed so that the driver’s
seat and steering column will automati-
cally move when the shift lever is in the P
(Park) position. This allows the driver to get
into and out of the driver’s seat more
easily.
The driver’s seat will slide backward and
the steering wheel will move up when the
driver’s door is opened with the ignition
switch in the LOCK position.
The driver’s seat and steering wheel will
return to the previous positions when the
ignition switch is pushed to the ACC
position.
The driver’s seat will not return to the
previous positions if the seat or steering
adjusting switch is operated when the seat
is at the exit position.
Pre-driving checks and adjustments3-27
AUTOMATIC DRIVE POSITIONER
Condition:

Black plate (164,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
3-28Pre-driving checks and adjustments
Cancel or activate entry/exit func-
tion
Y51D-V-E01-115CBE46-BE91-4686-ABD6-BC9952E15046The shift lever must be in the P (Park)
position with the ignition switch in the OFF
position.
The entry/exit function can be activated or
canceled by pressing and holding the SET
switch for more than 10 seconds.
The indicator lights on the memory
switches (1 and 2) will blink once when
the function is canceled, and the indicator
lights will blink twice when the function is
activated. Note that the indicator lights
may illuminate after 5 seconds while
holding the SET switch. This indicates
readiness for linking the Intelligent Key to
a stored memory position. Keep the SET
switch pressed for more than 10 seconds
to turn on or off the entry/exit function.
The entry/exit function can also be acti-
vated or canceled if the“Lift Steering
Wheel on Exit” key or“Slide Driver Seat
Back on Exit” key is turned to ON or OFF in
the “Comfort settings” settings. (See“Ve-
hicle information and settings” (P.4-10).)
Initialize entry/exit functionY51D-V-E01-BC9F8DD7-6ABF-4E49-BF93-F0A27D40B9E9If the battery cable is disconnected, or if
the fuse opens, the entry/exit function will
not work though this function was set on
before. In such a case, after connecting the
battery or replacing with a new fuse, open
and close the driver’s door more than two
times after the ignition switch is turned
from the ON position to the LOCK position.
The entry/exit function will be activated.
JVP0241X
SEAT SYNCHRONIZATION FUNCTIONY51D-V-E01-D911BEBD-6096-44D1-85CC-1FF7231C5236The seat synchronization function automa-
tically adjusts the positions of the steering
wheel and outside mirrors when the seat is
adjusted using the power seat switches.
However, the steering wheel and outside
mirrors will not move if the seat is adjusted
over the maximum thresholds. The system
considers that the steering wheel and
outside mirror adjustments are not neces-
sary because the seat may not be adjusted
for the driving position. Note that the
function is set to disabled as the factory
default setting.
Condition:

Black plate (189,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
To turn on the screen, set this item to the
“ON”position or push the “
”button.
Brightness/Contrast/Background Color:
GUID-CA441E56-2FD0-4540-A74C-DB510E9F7AE0To adjust the brightness, contrast and
background color of the screen, select the
appropriate “Brightness”, “Contrast”or
“Background Color” key and push the
ENTER button.
Then, you can adjust the brightness, and
the contrast using the INFINITI controller.
Switch the background color to the day-
time mode or the nighttime mode by
pushing the ENTER button.
SAA3151
Models with navigation system
JVH0182M
Models without navigation system
Comfort settingsY51D-V-E01-A36015FC-1163-41D7-A9C8-9288FFB08258Models with navigation system
The display as illustrated will appear when
pushing the SETTING button and selecting
the “Others” key, and then selecting the
“Comfort” key. This key does not appear on
the display until the ignition switch is
pushed to the ON position.
Models without navigation system
The display as illustrated will appear when
pushing the SETTING button and selecting
the “Comfort” key. This key does not
appear on the display until the ignition
switch is pushed to the ON position.
Auto Interior Illumination:
GUID-CA441E56-2FD0-4540-A74C-DB510E9F7AE0When this item is turned to ON, the interior
lights will illuminate if any door is un-
locked.
Light Sensitivity:
GUID-CA441E56-2FD0-4540-A74C-DB510E9F7AE0Adjust the sensitivity of the automatic
headlights higher (right) or lower (left).
Lift Steering Wheel on Exit (if so
equipped):
GUID-CA441E56-2FD0-4540-A74C-DB510E9F7AE0When this item is turned to ON, the
steering wheel moves upward for easy exit
if the ignition switch is in the LOCK
position and the driver’s door is opened.
Monitor, climate, audio, phone and voice recognition systems4-21
Condition:

Black plate (206,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
4-38Monitor, climate, audio, phone and voice recognition systems
—For U.S.: 60 to 908F (16 to 328C)
— For Canada: 64 to 908F (18 to 328C)
Air recirculation:
GUID-CA441E56-2FD0-4540-A74C-DB510E9F7AE0Push the air recirculation “”button to
change the air circulation mode. When the
indicator light illuminates, the flowing air
is recirculated inside the vehicle.
The air recirculation mode cannot be
activated when the air conditioner is in
the front defrosting mode “
”.
Outside air circulation:
GUID-CA441E56-2FD0-4540-A74C-DB510E9F7AE0Push the outside air circulation “”
button to change the air circulation mode.
When the indicator light illuminates, the
flowing air is drawn from outside the
vehicle.
Automatic air intake control:
GUID-CA441E56-2FD0-4540-A74C-DB510E9F7AE0To set the automatic control mode, perform
one of the following operations.
. When the outside air circulation mode
is on, push and hold the outside air
circulation “
”button for more than
2 seconds.
. When the air recirculation mode is on,
push and hold the air recirculation
“
” button for more than 2 seconds.
When setting the automatic control mode, both indicator lights will blink twice
indicating that the system is in the
automatic control mode.
Air flow control:
GUID-CA441E56-2FD0-4540-A74C-DB510E9F7AE0Pushing the
“”button selects the air
outlet to:
: Air flows from center and side ventilators.
: Air flows from center and side ventilators and foot outlets.
: Air flows mainly from foot outlets.
: Air flows from defroster and foot outlets.
SAA3002
Models with navigation system
JVH0054M
Models without navigation system
Condition: