INFINITI Q70 2014 Owners Manual

Black plate (459,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
ated by the battery is explosive. Do not
allow battery fluid to contact your skin,
eyes, fabrics, or painted surfaces. After
touching a battery or battery cap, do not
touch or rub your eyes. Thoroughly wash
your hands. If the acid contacts your
eyes, skin or clothing, immediately flush
with water for at least 15 minutes and
seek medical attention.
. Do not operate the vehicle if the fluid in
the battery is low. Low battery fluid can
cause a higher load on the battery which
can generate heat, reduce battery life,
and in some cases lead to an explosion.
. When working on or near a battery,
always wear suitable eye protection and
remove all jewelry.
. Battery posts, terminals and related
accessories contain lead and lead com-
pounds. Wash hands after handling.
. Keep the battery out of the reach of
children.
DI0137MA
Check the fluid level in each cell (Remove
the battery cover if it is necessary). It
should be between the UPPER LEVEL
*1
and LOWER LEVEL*2lines.
If it is necessary to add fluid, add only
distilled water to bring the level to the
indicator in each filler opening. Do not
overfill.
SDI1480C
1. Remove the cell plugs*A.
2. Add distilled water up to the UPPER LEVEL
*1line.
If the side of the battery is not clear,
check the distilled water level by
looking directly above the cell; the
condition
*1indicates OK and the
conditions
*2needs more to be added.
3. Tighten cell plugs
*A.
Vehicles operated in high temperatures or
under severe conditions require frequent
checks of the battery fluid level.
Maintenance and do-it-yourself8-21
Condition:

Black plate (460,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
8-22Maintenance and do-it-yourself
JUMP STARTINGY51D-V-E01-0AAB0CA9-4991-4590-8F41-F3A34B9AA084If jump starting is necessary, see“Jump
starting” (P.6-9). If the engine does not
start by jump starting, the battery may
have to be replaced. Contact an INFINITI
retailer.
Y51D-V-E01-EEE1FA47-944D-4234-8652-FA1B4A99ADFC
CAUTION
. Do not ground accessories directly to the
battery terminal. Doing so will bypass
the variable voltage control system and
the vehicle battery may not charge
completely.
. Use electrical accessories with the en-
gine running to avoid discharging the
vehicle battery.
The variable voltage control system mea-
sures the amount of electrical discharge
from the battery and controls voltage
generated by the generator.
Y51D-V-E01-6ADF95B7-2D41-4AEE-99FC-6C4F047C2DAF
SDI2545
VK56VD engine
SDI2119
VQ37VHR engine
VARIABLE VOLTAGE CONTROL SYSTEM DRIVE BELTS
Condition:

Black plate (461,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
1. Power steering fluid pump
2. Alternator
3. Crankshaft pulley
4. Air conditioner compressor
5. Drive belt auto-tensioner
WARNING
Be sure the ignition switch is in the OFF or
LOCK position before servicing drive belts.
The engine could rotate unexpectedly.
1. Visually inspect each belt for signs ofunusual wear, cuts, fraying or loosen-
ess. If the belt is in poor condition or
loose, have it replaced or adjusted by
an INFINITI retailer.
2. Have the belts checked regularly for condition and tension in accordance
with the maintenance schedule in your
“INFINITI Service and Maintenance
Guide”.
Y51D-V-E01-BAFEF7A1-AE7C-43AA-A355-1FA8A7A79074
WARNING
Be sure the engine and the ignition switch
are off and that the parking brake is
engaged securely.
CAUTION
Be sure to use the correct socket to remove
the spark plugs. An incorrect socket can
damage the spark plugs.
SDI2020
REPLACING SPARK PLUGSY51D-V-E01-5A1D3AA1-EC43-4BAE-B27E-C6EBBD832A65If replacement is required, see an INFINITI
retailer for servicing.
Iridium-tipped spark plugsY51D-V-E01-38C2D7CB-E5A3-44D4-8FFC-4A1A5D208F6CIt is not necessary to replace the iridium-
tipped spark plugs as frequently as the
conventional type spark plugs since they
will last much longer. Follow the main-
tenance schedule in “INFINITI Service and
Maintenance Guide”, but do not reuse
them by cleaning or regapping.
Maintenance and do-it-yourself8-23
SPARK PLUGS
Condition:

Black plate (462,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
8-24Maintenance and do-it-yourself
Always replace spark plugs with recom-
mended or equivalent ones.
Y51D-V-E01-EBDFA462-1DEC-47BB-9E1B-9849EB2EE182
SDI2549
VK56VD engine
SDI2546
VQ37VHR engine
Remove the retainers
*1as illustrated and
pull out the filter element
*2.
The filter element should not be cleaned
and reused. Replace it according to the
maintenance intervals. See “INFINITI Ser-
vice and Maintenance Guide” for mainte-
AIR CLEANER
Condition:

Black plate (463,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
nance intervals. When replacing the filter,
wipe the inside of the air cleaner housing
and the cover with a damp cloth.
WARNING
.Operating the engine with the air
cleaner removed can cause you or others
to be burned. The air cleaner not only
cleans the air, it stops flame if the
engine backfires. If it isn’t there, and the
engine backfires, you could be burned.
Do not drive with the air cleaner
removed, and be careful when working
on the engine with the air cleaner
removed.
. Never pour fuel into the throttle body or
attempt to start the engine with the air
cleaner removed. Doing so could result
in serious injury.
Y51D-V-E01-3AAC18CC-496A-4CFC-A885-D20A2F6859E1
CLEANINGY51D-V-E01-7847FFC1-7DCA-4EE2-B775-CA92E386F50AIf your windshield is not clear after using
the windshield washer or if a wiper blade
chatters when running, wax or other
material may be on the blade or wind-
shield.
Clean the outside of the windshield with a
washer solution or a mild detergent. Your
windshield is clean if beads do not form
when rinsing with clear water.
Clean each blade by wiping it with a cloth
soaked in a washer solution or a mild
detergent. Then rinse the blade with clear
water. If your windshield is still not clear
after cleaning the blades and using the
wiper, replace the blades.
Worn windshield wiper blades can damage
the windshield and impair driver vision.
Maintenance and do-it-yourself8-25
WINDSHIELD WIPER BLADES
Condition:

Black plate (464,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
8-26Maintenance and do-it-yourself
SDI2048
REPLACINGY51D-V-E01-2BEC5F4C-D760-4B69-84E3-337BD465F889Replace the wiper blades if they are worn.
Before replacing the wiper blades, the
wiper should be in the fully up position
to avoid scratching the engine hood or
damaging the wiper arm. To pull up the
wiper arm, see“Windshield wiper and
washer switch” (P.2-32).
1. Pull the wiper arm.
2. Push the release tab
*A, and then
move the wiper blade down the wiper
arm
*1while pushing the release tab
to remove. 3. Insert the new wiper blade onto the
wiper arm until a click sounds.
4. Rotate the wiper blade so the dimple is in the groove.
CAUTION
. After wiper blade replacement, return
the wiper arm to its original position;
otherwise it may be damaged when the
hood is opened.
. Make sure the wiper blades contact the
glass; otherwise the arm may be da- maged from wind pressure.
Condition:

Black plate (465,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
SDI2362
Be careful not to clog the washer nozzle
*A. This may cause improper windshield
washer operation. If the nozzle is clogged,
remove any objects with a needle or small
pin
*B. Be careful not to damage the
nozzle.
Y51D-V-E01-4F238978-A678-4BC5-A547-90FB4F14D1F8If the brakes do not operate properly, have
the brakes checked by an INFINITI retailer.
SELF-ADJUSTING BRAKESY51D-V-E01-22E38629-DCD8-4E65-AEEF-BF5D3567BF7BYour vehicle is equipped with self-adjust-
ing brakes.
The disc-type brakes self-adjust every time
the brake pedal is applied.
WARNING
See an INFINITI retailer for a brake system
check if the brake pedal height does not
return to normal.
BRAKE PAD WEAR WARNINGY51D-V-E01-D89227A8-C2EA-43BF-8410-9B39CA613024The disc brake pads have audible wear
warnings. When a brake pad requires
replacement, it will make a high pitched
scraping sound when the vehicle is in
motion. This scraping sound will first occur
only when the brake pedal is depressed.
After more wear of the brake pad, the
sound will always be heard even if the
brake pedal is not depressed. Have the
brakes checked as soon as possible if the
wear warning sound is heard.
Under some driving or climate conditions, occasional brake squeak, squeal or other
noise may be heard. Occasional brake
noise during light to moderate stops is
normal and does not affect the function or
performance of the brake system.
Proper brake inspection intervals should
be followed.
For additional information,
see the maintenance log section of your
“INFINITI Service and Maintenance Guide”
for maintenance intervals.
Maintenance and do-it-yourself8-27
BRAKES
Condition:

Black plate (466,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
8-28Maintenance and do-it-yourself
Y51D-V-E01-29097B28-1FE0-4182-A485-A2047D0C5A2D
SDI2584
SDI2566
ENGINE COMPARTMENTY51D-V-E01-AFE79579-EF18-4DDE-B356-BDC18538EFB0
CAUTION
Never use a fuse of a higher or lower
amperage rating than that specified on the
fuse box cover. This could damage the
electrical system or cause a fire.
If any electrical equipment does not
operate, check for an open fuse.
1. Be sure the ignition switch is pushed tothe OFF or LOCK position and the
headlight switch is turned to OFF.
2. Open the engine hood and remove the cover on the battery and the fuse/
fusible link holder.
3. Remove the fuse/fusible link holder
cover.
4. Remove the fuse with the fuse puller.
SDI1754
5. If the fuse is open*A, replace it with a
new fuse
*B. Spare fuses are stored in
the passenger compartment fuse box.
6. If a new fuse also opens, have the electrical system checked and repaired
by an INFINITI retailer.
The holder
*1also contains the fuses. For
checking and/or replacing, see an INFINITI
retailer.
Fusible linksY51D-V-E01-3E721E86-CD62-4D57-8D17-0637DAF969EFIf any electrical equipment does not
operate and fuses are in good condition,
check the fusible links. If any of these
fusible links are melted, replace only with
FUSES
Condition:

Black plate (467,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
genuine INFINITI parts.
SDI2034
PASSENGER COMPARTMENTY51D-V-E01-D27C130D-9311-435F-AE5F-9BAD54FDFC82
CAUTION
Never use a fuse of a higher or lower
amperage rating than that specified on the
fuse box cover. This could damage the
electrical system or cause a fire.
If any electrical equipment does not
operate, check for an open fuse.
1. Be sure the ignition switch is pushed tothe OFF or LOCK position and the
headlight switch is turned to OFF. 2. Open the fuse box lid.
3. Remove the fuse with the fuse puller
*A.
4. If the fuse is open, replace it with a new fuse.
5. If a new fuse also opens, have the electrical system checked and repaired
by an INFINITI retailer. Spare fuses are
stored in the fuse box.
Maintenance and do-it-yourself8-29
Condition:

Black plate (468,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
8-30Maintenance and do-it-yourself
SDI2704
Extended storage fuse switch (if so
equipped)
GUID-9D25C740-4001-4543-BF7B-2B71EA47B8A7To reduce battery drain, the extended
storage fuse switch comes from the factory
switched off. Prior to delivery of your
vehicle, the switch is pushed in (switched
on) and should always remain on.
If any electrical equipment does not
operate, remove the extended storage fuse
switch and check for an open fuse.NOTE:
If the extended storage fuse switch mal-
functions or if the fuse is open, it is not
necessary to replace the switch. In this
case, remove the extended storage fuse
switch and replace it with a new fuse of
the same rating.
How to remove the extended storage fuse
switch:
GUID-CA441E56-2FD0-4540-A74C-DB510E9F7AE01. To remove the extended storage fuse
switch, be sure the ignition switch is in
the OFF or LOCK position.
2. Be sure the headlight switch is in the OFF position.
3. Remove the fuse box cover.
4. Pinch the locking tabs
*1found on
each side of the storage fuse switch.
5. Pull the storage fuse switch straight out from the fuse box
*2.
Y51D-V-E01-0F281EEB-8605-4AC8-B4C1-14A643CAD5F2
CAUTION
Be careful not to allow children to swallow
the battery and removed parts.
INTELLIGENT KEY BATTERY REPLACEMENT
Condition: