jacking INFINITI QX 2011 Owners Manual

1. Cargo light (P. 2-68)
2. Cup holders (3rd row seat) (P. 2-56)
3. Rear ventilators (P. 4-30)
4. Coat hooks (P. 2-59)
5. Rear personal lights (P. 2-66)6. Tray (P. 2-58)
— USB memory operation* (P. 4-61)
— iPod player operation* (P. 4-70)
7. Door armrest — Power window controls (P. 2-61)
— Power door lock switch (P. 3-5) 8.
Automatic drive positioner switch (P. 3-30)
9. Sun visors (P. 3-26)
10. Moon roof switch (P. 2-63)
11. Map lights (P. 2-66)
12. Sunglasses holder (P. 2-56)
13. Inside rearview mirror (P. 3-27)
— HomeLink universal transceiver
(P. 2-68)
14. Cargo area — Power outlet (P. 2-52)
— Cargo floor box (P. 2-60)
— Luggage hooks (P. 2-59)
— Jacking tools (P. 6-4)
15. Rear console box (P. 2-58) — Cup holders (2nd row seat)* (P. 2-54)
— Pocket* (P. 2-58)
16. Cup holders (2nd row seat)* (P. 2-54)
17.
Dual head restraint DVD system* (P. 4-83)
18. Console box (P. 2-57) — Power outlet (P. 2-52)
— Auxiliary input jacks* (P. 4-84)
— Rear automatic air conditioning
system* (P. 4-37)
19. Power outlet (P. 2-52)/Front cup holders (P. 2-54)
*: if so equipped
SSI0743
PASSENGER COMPARTMENT
Illustrated table of contents0-5

Blocking wheels
Place suitable blocks1at both the front and
back of the wheel diagonally opposite the flat
tire to prevent the vehicle from moving when it
is jacked up.
WARNING
Be sure to block the wheel as the vehicle may
move and result in personal injury.
Getting the spare tire and tools
1. Open the lift gate.
2. Raise the cargo floor board
1using the
handle
A, then hang it on the edge of the
lift gate opening
2using the hookB.
WARNING
When removing jacking tools, be sure the rubber
sound suppressor
1, used to control jack stand
from rattling against metal, is not attached to the
MCE0001ASCE0872
SCE0923
6-4In case of emergency

jacking tool. If rubber sound suppressor re-
mains on jack when vehicle is being jacked up,
the vehicle will be unstable and may fall off jack
stand causing serious injury of death.
3. Remove the cargo floor cover.
4. Remove the jacking tools.5. Securely screw to connect the T-shapedend of the jack rod and two extension
bars
1as illustrated.
6. Fit the square end of the jack rod into the square hole of the wheel nut wrench to
form a handle
2. 7. Locate the oval opening above the middle
of the rear bumper.
8. Place the T-shaped end of the jack rod through the opening and direct it towards
the spare wheel winch assembly, located
directly above the spare wheel.
SCE0915
In case of emergency6-5

CAUTION
When storing the wheel, be sure to mount the
wheel horizontally. Securing the wheel that is
in a tilted position as illustrated may cause
looseness and dropping of the wheel while
driving. Lower the wheel on the ground again,
and make sure that the hanging plate is prop-
erly set. Hang the wheel again and make sure
that the wheel is held horizontally, then store
the wheel.
Jacking up the vehicle and removing
the damaged tire
WARNING
●Never get under the vehicle while it is sup-
ported only by the jack. If it is necessary to
work under the vehicle, support it with
safety stands.
● Use only the jack provided with your vehicle
to lift the vehicle. Do not use the jack pro-
vided with your vehicle on other vehicles.
The jack is designed for lifting only your ve-
hicle during a tire change.
● Use the correct jack-up points. Never use any
other part of the vehicle for jack support. ●
Never jack up the vehicle more than
necessary.
● Never use blocks on or under the jack.
● Do not start or run the engine while vehicle is
on the jack, as it may cause the vehicle to
move. This is especially true for vehicles
with limited slip differentials.
● Do not allow passengers to stay in the ve-
hicle while it is on the jack.
Carefully read the caution label attached to the
jack body and the following instructions.
SCE0917
In case of emergency6-7

3. Install the assembled jack rod into thejack as shown.
4. Carefully raise the vehicle until the clear- ance between the tire and ground is
achieved.
5. To lift the vehicle, securely hold the jack lever and rod with both hands and turn
the jack lever.
NOTE:
Before jacking up the vehicle, make sure the
ignition switch is placed in the OFF position. If
the vehicle is lifted up with the engine running,
the auto-leveling suspension will become dis-
abled after 120 seconds. To reset the auto-
leveling suspension, cycle the ignition switch
ON/OFF one time.
Installing the spare tire
1. Clean any mud or dirt from the surface
between the wheel and hub.
2. Carefully put the spare tire on and tighten the wheel nuts finger tight.
3. With the wheel nut wrench, tighten wheel nuts alternately and evenly in the se-
quence as illustrated (
1,2,3,4,5,
6) until they are tight.
4. Lower the vehicle slowly until the tire touches the ground. Then, with the wheel
nut wrench, tighten the wheel nuts se-
curely in the sequence as illustrated.
Lower the vehicle completely.
NCE130SCE0910
In case of emergency6-9