washer fluid INFINITI QX 2011 Owners Manual

1. Hood (P. 3-18)
2. Windshield wiper and washer— Switch operation (P. 2-32)
— Rain-sensing auto wiper system (P. 2-33)
— Wiper blade replacement (P. 8-19) — Window washer fluid (P. 8-14)
— Windshield wiper deicer* (P. 2-35)3. Moonroof (P. 2-63)
4. Power windows (P. 2-61)
5. Roof rack (P. 2-60)6. Front Sensor
— Around View Monitor (P. 4-19)
7. Recovery hook (P. 6-17)
8. Front view camera (P. 4-19)
9. Fog light (P. 2-42)
10. Headlight washers* (P. 2-41)
11. Headlight and turn signal (P. 2-36) — Bulb replacement (P. 8-26)
— Adaptive Front lighting System (AFS)*
(P. 2-40)
12. Tires — Wheel and tires (P. 8-29, P. 9-9)
— Flat tire (P. 6-2)
— Tire pressure monitoring system
(TPMS) (P. 2-14, P. 5-3)
13. Outside mirrors (P. 3-28) — Side view camera (P. 4-19)
— Welcome light (P. 2-65)
14. Side turn signal lights (bulb replacement) (P. 8-26)
15. Doors — Keys (P. 3-2)
— Door locks (P. 3-4)
— Intelligent Key system (P. 3-6)
— Remote keyless entry system (P. 3-15)
16. Child safety rear door locks (P. 3-6)
*: if so equipped
SSI0729
EXTERIOR FRONT
Illustrated table of contents0-3

1. Fuel-filler door (P. 3-23)— Fuel recommendation (P. 9-4)
2. Antenna (P. 4-82)
3. Rear combination light (bulb replacement) (P. 8-26) 4. Rear window defroster (P. 2-35)
5. Satellite antenna (P. 4-40)
6. Rear view camera (P. 4-19)
7. High-mounted stop light
(bulb replacement) (P. 8-26) 8. Lift gate (P. 3-19)
— Intelligent Key system (P. 3-6)
9. Rear window wiper and washer — Switch operation (P. 2-34)
— Window washer fluid (P. 8-14)
10. Spare tire (under the vehicle) (P. 6-2)
11. Rear Sensor — Around View Monitor (P. 4-19)
12. Recovery hook (P. 6-17)
13. Trailer hitch (P. 9-21)
SSI0737
EXTERIOR REAR
0-4Illustrated table of contents

VK56VD ENGINE
1. Window washer fluid reservoir (P. 8-14)
2. Fuse/fusible link holder (P. 8-21)
3. Engine oil dipstick (P. 8-9)4. Power steering fluid reservoir (P. 8-12)
5. Engine oil filler cap (P. 8-9)
6. Brake fluid reservoir (P. 8-12)
7. Fuse/fusible link holder (P. 8-21)
8. Battery (P. 8-15)9. Radiator filler cap (P. 8-7)
10. Engine coolant reservoir (P. 8-7)
11. Drive belts (P. 8-17)
12. Air cleaner (P. 8-18)
SDI2585
ENGINE COMPARTMENT
0-10Illustrated table of contents

CAUTION
●The TPMS is not a substitute for the regular
tire pressure check. Be sure to check the tire
pressure regularly.
● If the vehicle is being driven at speeds of less
than 16 MPH (25 km/h), the TPMS may not
operate correctly.
● Be sure to install the specified size of tires to
the four wheels correctly.
Master warning light
When the ignition switch is in the ON position,
the master warning light illuminates if any of
the following are displayed on the dot matrix
liquid crystal display:
● No key warning
● Low fuel warning
● Low washer fluid warning
● Parking brake release warning
● Door/lift gate open warning
● Loose fuel cap warning (if so equipped)
● Check tire pressure warning (if so equipped)
See “DOT MATRIX LIQUID CRYSTAL DISPLAY”
later in this section.
Preview Function warning
light (orange; if so equipped)
The light comes on if there is a malfunction in
the Brake Assist (with Preview Function) sys-
tem.
If the warning light comes on, park the vehicle
in a safe place. Turn the engine off, restart the
engine, then resume driving.
If it is not possible to set the system or the
indicator stays on, it may indicate that the sys-
tem is malfunctioning. Although the vehicle is
still driveable under normal conditions, have the
vehicle checked at an INFINITI retailer.
Seat belt warning light and
chime
The light and chime remind you to fasten seat
belts. The light illuminates whenever the igni-
tion switch is pushed to the ON position, and
will remain illuminated until the driver’s seat
belt is fastened. At the same time, the chime
will sound for about 6 seconds unless the
driver’s seat belt is securely fastened.
The seat belt warning light for the front passen-
ger will illuminate if the seat belt is not fastened
when the front passenger’s seat is occupied.
For approximately 5 seconds after the ignition switch is in the ON position, the system does
not activate the warning light for the front
passenger.
See “SEAT BELTS” in the “1. Safety — Seats,
seat belts and supplemental restraint system”
section for precautions on seat belt usage.
Supplemental air bag
warning light
After pushing the ignition switch to the ON
position, the supplemental air bag warning
light will illuminate. The supplemental air bag
warning light will turn off after about 7 seconds
if the front-impact air bag and side air bag,
curtain and rollover air bag systems and/or
pretensioner seat belts are operational.
If any of the following conditions occur, the
front air bag, side air bag, curtain and rollover
air bag and pretensioner systems needs servic-
ing and your vehicle must be taken to your
nearest INFINITI retailer.
●
The supplemental air bag warning light re-
mains on after approximately 7 seconds.
● The supplemental air bag warning light
flashes intermittently.
● The supplemental air bag warning light does
not come on at all.
2-16Instruments and controls

8. Parking brake release warning
This warning appears when the vehicle speed is
above 4 MPH (7 km/h) and the parking brake is
applied.
9. Low fuel warning
This warning appears when the fuel level in the
tank is getting low. Refuel as soon as it is
convenient, preferably before the fuel gauge
reaches the 0 (Empty) position.
There is a small reserve of fuel remaining in the
tank when the fuel gauge reaches the 0 (Empty)
position.
10. Low washer fluid warning
This warning appears when the washer tank
fluid is at a low level. Add washer fluid as
necessary. (See “WINDOW WASHER FLUID” in
the “8. Maintenance and do-it-yourself” sec-
tion.)
11. Door/lift gate open warning
(ignition switch is in the ON position)
This warning appears if any of the doors and/or
the lift gate are open or not closed securely. The
vehicle icon indicates which door or the lift gate
is open on the display.
12. Loose fuel cap warning (if so
equipped)
This warning appears when the fuel-filler cap is
not tightened correctly after the vehicle has
been refueled. (See “FUEL-FILLER CAP” in the
“3. Pre-driving checks and adjustments” sec-
tion.)
13. Check tire pressure warning (if so
equipped)
This warning appears when the low tire pres-
sure warning light in the meter illuminates and
low tire pressure is detected. If this warning
appears, stop the vehicle and adjust the tire
pressure to the recommended COLD tire pres-
sure shown on the Tire and Loading Information
label. (See “Low tire pressure warning light”
earlier in this section and “TIRE PRESSURE
MONITORING SYSTEM (TPMS)” in the “5. Start-
ing and driving” section.)
14. “TIMER” indicator
This indicator appears when the set “TIMER”
indicator activates. You can set the time for up
to 6 hours. (See “TRIP COMPUTER” later in this
section.)
15. Low outside temperature warning
This warning appears if the outside temperature
is below 37°F (3°C). The warning can be set not
to be displayed. (See “TRIP COMPUTER” later in
this section.)
16. Four-Wheel Drive (4WD) shift
indicator (4WD models)
This indicator shows the Four-Wheel Drive
(4WD) driving mode (AUTO, 4HI or 4LO) that is
selected by the 4WD shift switch. (See “INFINITI
ALL-MODE 4WD” in the “5. Starting and driv-
ing” section.)
17. Intelligent Cruise Control (ICC)
system MAIN switch indicator (if so
equipped)
The indicator is displayed when the Intelligent
Cruise Control (ICC) system main switch is
pushed. When the main switch is pushed again,
the indicator disappears. While the main switch
indicator is displayed, the ICC system is opera-
tional. (See “INTELLIGENT CRUISE CONTROL
(ICC) SYSTEM” in the “5. Starting and driving”
section.)
2-24Instruments and controls

If the light still remains on and/or the engine will
not start, see an INFINITI retailer for INFINITI Ve-
hicle Immobilizer System service as soon as
possible. Please bring all Intelligent Keys that
you have when visiting an INFINITI retailer for
service.WARNING
In freezing temperatures the washer solution
may freeze on the window and obscure your
vision which may lead to an accident. Warm the
window with the defroster before you wash the
window.
CAUTION
●Do not operate the washer continuously for
more than 30 seconds.
● Do not operate the washer if the reservoir
tank is empty.
● Do not fill the window washer reservoir tank
with washer fluid concentrates at full
strength. Some methyl alcohol based
washer fluid concentrates may permanently
stain the grille if spilled while filling the win-
dow washer reservoir tank.
● Pre-mix washer fluid concentrates with wa-
ter to the manufacturer’s recommended lev-
els before pouring the fluid into the window
washer reservoir tank. Do not use the win-
dow washer reservoir tank to mix the washer
fluid concentrate and water. If the windshield wiper operation is interrupted
by snow or ice, the wiper may stop moving to
protect its motor. If this occurs, turn the wiper
switch to the OFF position and remove the snow
or ice that is on and around the wiper arms. In
approximately 1 minute, turn the switch on again
to operate the wiper.
WINDSHIELD WIPER AND WASHER SWITCH
2-32Instruments and controls

The windshield wiper and washer operates
when the ignition switch is in the ON position.
Push the lever down to operate the wiper at the
following speed:
1AUTO — operates the rain-sensing auto
wiper system. (See “RAIN-SENSING AUTO
WIPER SYSTEM” later in this section.)
2LO — continuous low speed operation
3HI — continuous high speed operation
4MIST — one sweep operation of the wiper
WASHER OPERATION
To operate the washer, pull the lever toward the
back of the vehicle
5until the desired amount
of washer fluid is spread on the windshield. The
wiper will automatically operate several times.
The headlight washer (if so equipped) will also
operate with operation of the windshield
washer. (See “HEADLIGHT WASHER” later in this
section.)
Wiper drip wipe system:
The wiper will also operate once about 3 sec-
onds after the washer and wiper are operated.
This operation is to wipe washer fluid that has
dripped on the windshield.
RAIN-SENSING AUTO WIPER SYSTEM
The rain-sensing auto wiper system can auto-
matically turn on the wipers and adjust the
wiper speed depending on the rainfall and the
vehicle speed by using the rain sensor located
on the upper part of the windshield.
To set the rain-sensing auto wiper system, push
the lever down to the AUTO position
1. The
wiper will sweep once while the ignition switch
is in the ON position.
SIC4492SIC4258
Instruments and controls2-33

The rain sensor sensitivity level can be adjusted
by turning the knob toward the front
2(High)
or toward the rear
3(Low).
● High — High sensitive operation
● Low — Low sensitive operation
To turn the rain-sensing auto wiper system off,
push up the lever to the OFF position, or pull
down the lever to the LO or HI position.
CAUTION
Do not touch the rain sensor and around it when
the wiper switch is in the AUTO position and the
ignition switch is in the ON position. The wipers
may operate unexpectedly and cause to an in-
jury or a wiper damage.
● The rain-sensing auto wipers are intended for
use during rain. If the switch is left in the
AUTO position, the wipers may operate unex-
pectedly when dirt, fingerprints, oil film or
insects are stuck on or around the sensor.
The wipers may also operate when exhaust
gas or moisture affect the rain sensor.
● The rain-sensing auto wipers may not oper-
ate if rain does not hit the rain sensor even if
it is raining. ●
When the windshield glass is coated with
water repellent, the speed of the rain-
sensing auto wipers may be higher even
though the amount of the rainfall is small.
● Be sure to turn off the rain-sensing auto wiper
system when you use a car wash.
● Using genuine wiper blades is recommended
for proper operation of the rain-sensing auto
wiper system. (See “WINDSHIELD WIPER
BLADES” in the “8. Maintenance and do-it-
yourself” section for wiper blade replace-
ment.)
WARNING
In freezing temperatures the washer solution
may freeze on the rear window glass and ob-
scure your vision. Warm the rear window with
the defroster before you wash the rear window.
CAUTION
● Do not operate the washer continuously for
more than 30 seconds.
● Do not operate the washer if the reservoir
tank is empty.
● Do not fill the window washer reservoir tank
with washer fluid concentrates at full
strength. Some methyl alcohol based
washer fluid concentrates may permanently
stain the grille if spilled while filling the win-
dow washer reservoir tank.
● Pre-mix washer fluid concentrates with wa-
ter to the manufacturer’s recommended lev-
els before pouring the fluid into the window
washer reservoir tank. Do not use the win-
dow washer reservoir tank to mix the washer
fluid concentrate and water.
REAR WINDOW WIPER AND WASHER
SWITCH
2-34Instruments and controls

HEADLIGHT WASHER (if so equipped)
The headlight washer operates when the head-
light is on and the ignition switch is in the ON
position.
Pull the windshield washer switch toward you.
The headlight washer operates with the wind-
shield washer operation. This operation acti-
vates once each time either the ignition switch
or the headlight switch is turned off and on.
After the first operation, the headlight washer
operates once at every fifth operation of the
windshield washer.
CAUTION
●Do not operate the washer continuously for
longer than 30 seconds.
● Do not operate the headlight washer if the
window washer fluid reservoir is empty.
Instrument brightness control
The instrument brightness control switch can be
operated when the ignition switch is in the ON
position. When the switch is operated, the dot
matrix liquid crystal display switches to the
brightness adjustment mode.
Push the upper switch
Ato brighten the
instrument panel lights. The bar
1moves to
the + side. When reaching the maximum bright-
ness, “MAX” appears on the display
2.
Push the lower switch
Bto dim the instrument
panel lights. The bar
1moves to the side.
When reaching the minimum brightness, “MIN”
appears on the display
3. However, “MIN”
does not appear during the nighttime.SIC3270
SIC4378
Instruments and controls2-41

●Make sure the area around the vehicle is
clear.
● Check fluid levels such as engine oil, cool-
ant, brake fluid and window washer fluid as
frequently as possible, or at least whenever
you refuel.
● Check that all windows and lights are clean.
● Visually inspect tires for their appearance
and condition. Also check tires for proper
inflation.
● Lock all doors.
● Position seat and adjust head
restraints/headrests.
● Adjust inside and outside mirrors.
● Fasten seat belts and ask all passengers to
do likewise.
● Check the operation of warning lights when
the ignition switch is pushed to the ON
position. (See “WARNING/INDICATOR LIGHTS
AND AUDIBLE REMINDERS” in the “2. Instru-
ments and controls” section.)1. Apply the parking brake.
2. Move the selector lever to the P (Park) or
N (Neutral) position. (P is recommended.)
The starter is designed not to operate unless
the selector lever is in either of the above
positions.
3. Push the ignition switch to the ON posi-tion. Depress the brake pedal and push
the ignition switch to start the engine.
To start the engine immediately, push and
release the ignition switch while depressing
the brake pedal with the ignition switch in
any position.
● If the engine is very hard to start in
extremely cold weather or when restart-
ing, depress the accelerator pedal a little
(approximately 1/3 to the floor) and while
holding, crank the engine. Release the
accelerator pedal when the engine starts.
● If the engine is very hard to start because
it is flooded, depress the accelerator
pedal all the way to the floor and hold it.
Push the ignition switch to the ON posi-
tion to start cranking the engine. After 5
or 6 seconds, stop cranking by pushing
the ignition switch to OFF. After cranking
the engine, release the accelerator pedal.
Crank the engine with your foot off the accelerator pedal
by depressing the brake
pedal and pushing the push-button igni-
tion switch to start the engine. If the
engine starts, but fails to run, repeat the
above procedure.
CAUTION
Do not operate the starter for more than 15
seconds at a time. If the engine does not start,
push the ignition switch to OFF and wait 10
seconds before cranking again, otherwise the
starter could be damaged.
4. Warm-up
Allow the engine to idle for at least 30
seconds after starting. Do not race the en-
gine while warming it up. Drive at moderate
speed for a short distance first, especially in
cold weather. In cold weather, keep the
engine running for a minimum of 2 - 3
minutes before shutting it off. Starting and
stopping the engine over a short period of
time may make the vehicle more difficult to
start.
When racing the engine up to 4,000 rpm or
more under the no load condition, the en-
gine will enter the fuel cut mode.
BEFORE STARTING THE ENGINE STARTING THE ENGINE
Starting and driving5-13