brake sensor INFINITI QX30 2017 User Guide

•The on-board voltage is too low.
Once the causes listed above no longer apply,
the display message goes out. The FEB system
is operative again.
If the display message does not disappear:
•Pull over and stop the vehicle safely as soon
as possible, paying attention to road and
traffic conditions.
•Secure the vehicle against rolling away.
•Switch off the engine.
[Emergency Brake Inoperative]: The FEB system
is temporarily inoperative due to a malfunction.
The adaptive brake assist function may also
have failed.
It is recommended you visit an INFINITI retailer.
[Radar Sensors Dirty See Operator’s Manual]:
The FEB system is temporarily restricted or
inoperative. Possible causes:
•The sensor behind the INFINITI logo is dirty.
•The function of the FEB system is impaired
due to heavy rain or snow. A warning tone also sounds.
Once the causes listed above no longer apply,
the display message goes out. The FEB system
is operative again.
If the display message does not disappear:
•Pull over and stop the vehicle safely as soon
as possible, paying attention to road and
traffic conditions.
•Secure the vehicle against rolling away.
•Switch off the engine.
•Clean the area around the sensors.
•Restart the engine. The display message
disappears.
SYSTEM MAINTENANCE
The sensorAis located behind the INFINITI
logo at the front of the vehicle.
To keep the system operating properly, be sure
to observe the following:
•Always keep the sensor area of the INFINITI
logo clean.
•Do not strike or damage the areas around the
sensor.
•Do not cover or attach stickers or similar
objects on the front bumper near the sensor
area. This could cause failure or malfunction.
•Do not attach metallic objects near the sen-
sor area (brush guard, etc.). This could cause
failure or malfunction.
NSD645
5-66Starting and driving

ACTIVE SOUND ENHANCEMENT
The active sound enhancement generates
sounds according to engine speed through the
speakers
2and woofer1(if equipped) to
enhance the quality of the engine sound. IPA is an electronic parking aid with ultrasound.
It detects vehicles and open spaces on both
sides of the vehicle. A parking symbol indicates
a suitable parking space. Active steering inter-
vention can assist you during parking and when
exiting a parking space. The driver controls the
accelerator, brake and gear shift. You may also
use the parking sensor system (see
Parking
sensor system (if equipped) later in this sec-
tion).
IMPORTANT SAFETY NOTES
WARNING
•IPA is only an aid. It is not a substitute for
your attention to the immediate surround-
ings. The responsibility for safe maneuver-
ing and parking remains with you.
•Make sure that no persons, animals or ob-
jects are in the maneuvering range
•When the parking sensor system is deacti-
vated, IPA is also unavailable.
•While parking or pulling out of a parking
space, the vehicle swings out and can drive
onto areas of the oncoming lane. This could
cause you to collide with other road users.
There is a risk of an accident.
•Pay attention to other road users. Stop the
vehicle if necessary or cancel the IPA park-
ing procedure
•This system is not designed to prevent con-
tact with small or moving objects.
•If your vehicle sustains damage to the bum-
per fascia, leaving it misaligned or bent, the
sensing zone may be altered causing inac-
curate measurement of obstacles or false
alarms.
•This system is not designed to prevent con-
tact with small or moving objects.
•If your vehicle sustains damage to the bum-
per fascia, leaving it misaligned or bent, the
sensing zone may be altered causing inac-
curate measurement of obstacles or false
alarms.
CAUTION
Do not drive over obstacles such as curbs, as
you may damage the wheels or tires.
IPA may also display spaces not suitable for
parking, for example:
•Parking or stopping prohibition.
INTELLIGENT PARKING ASSIST (IPA) (IF
EQUIPPED)
5-68Starting and driving

•The parking space is bordered by an ob-
stacle, e.g. a tree, a post or a trailer.
1Detected parking space on the left.
2Parking symbol.
3Detected parking space on the right.
IPA is activated automatically when driving for-
wards. The system is operational at speeds of
up to approximately 19 MPH (30 km/h). While in
operation, the system independently locates
and measures parking spaces on both sides of
the vehicle
IPA will only detect parking spaces:
•Adjacent to the vehicle.
•Parallel or at right angles to the direction of
travel.
•That are parallel to the direction of travel and
are at least 5 ft (1.5 m) wide.
•That are parallel to the direction of travel and
at least 3.3 ft (1.0 m) longer than your
vehicle.
•That are at right angles to the direction of
travel and at least 3.3 ft (1.0 m) wider than
your vehicle.
NOTE
IPA cannot measure the length of a parking
space if it is at right angles to the direction of
travel. You will need to judge whether your ve-
hicle will fit in the parking space
When driving at speeds below 19 MPH (30
km/h) you will see parking symbol
2as a
status indicator in the vehicle information dis-
play. When a parking space has been detected,
an arrow towards the right
3or the left1also
appears. IPA only displays parking spaces on
the front-passenger side as standard. Parking
spaces on the driver’s side are displayed as
soon as the turn signal on the driver’s side is
activated. When parking on the driver’s side,
this must remain activated until you confirm the
use of IPA by pressing the button on the
steering wheel. The system automatically deter-
mines whether the parking space is parallel or
at right angles to the direction of travel. A parking space is displayed while you are
driving past it, and until you are approximately
50 ft (15 m) away from it.
PARKING
NOTE
When the parking sensor system detects ob-
stacles, you are responsible for braking in good
time.
1. Stop the vehicle when the parking symbol
shows the desired parking space in the
combination meter
2. Shift into position R. The [Start Park Assist? Yes: OK No:]
message appears in the vehicle information
display.
3. To cancel the procedure: press the
button on the steering wheel or pull away
or
4. To park using IPA press the button on
the steering wheel. The Park Assist [Observe
surroundings] message appears in the ve-
hicle information display.
5. Release the steering wheel.
6. Back up the vehicle, being ready to brake at all times. When backing up, drive at a speed
NSD612Upper display
5-70Starting and driving

below 5 MPH (10 km/h). Otherwise, IPA will
be canceled.
7. Stop as soon as the parking sensor system sounds the continuous warning tone, if not
before. Maneuvering may be required in
tight parking spaces.
The [Park Assist active Select D Observe
surroundings] message appears in the ve-
hicle information display.
8. Select transmission position D (Drive) while the vehicle is stationary.
IPA immediately steers in the other direc-
tion.
The [Park Assist Observe surroundings] mes-
sage appears in the vehicle information dis-
play.
NOTE
You will achieve the best results by waiting
for the steering procedure to complete before
pulling away.
9. Drive forwards and be ready to brake at all times.
Maneuvering may be required in tight park-
ing spaces. Drive forward and back up as
prompted by the parking sensor system
warning displays, several times if necessary. 10. Stop as soon as the parking sensor system
sounds the continuous warning tone, if not
before.
The [Park Assist active Select R] [Observe
surroundings] message appears in the ve-
hicle information display.
As soon as the parking procedure is com-
plete the [Park Assist switched off] mes-
sage appears and a warning tone sounds.
The vehicle is now parked.
11. Before leaving the vehicle, secure the ve- hicle against rolling away unintentionally:
•The electric parking brake must be ap-
plied.
•The transmission must be in position P
(Park) and the transmission position dis-
play must show P in the vehicle informa-
tion display.
•The key must be removed from the igni-
tion switch.
•On uphill or downhill gradients, the front
wheels must be turned towards the curb.
IPA no longer supports you with steering inter-
ventions. When IPA is finished, you must steer
again yourself. The parking sensor system is
still available. Parking tips:
•The way your vehicle is positioned in the
parking space after parking is dependent on
various factors. These include the position
and shape of the vehicles parked in front and
behind it and the conditions of the location.
It may be the case that IPA guides you too far
into a parking space, or not far enough into
it. In some cases, it may also lead you across
or onto the curb. If necessary you should
cancel the parking procedure with IPA.
•During the parking maneuver, the system will
indicate when you should shift to R (Reverse)
or D (Drive). However, you can freely choose
to shift gear whenever you feel you need to.
Should the transmission change take place
too early, the parking procedure will be
canceled. A sensible parking position can no
longer be achieved from this position.
EXITING A PARKING SPACE
In order that IPA can support when exiting the
parking space:
•You need to have parked using IPA.
•The border of the parking space must be high
enough at the front and the rear. A curb
stone is too small, for example.
Starting and driving5-71

•The border of the parking space must not be
too wide, as the position of the vehicle must
not exceed an angle of 45 degrees to the
starting position as it is manoeuvred into the
parking space.
•A total front and back maneuvering distance
of at least 1.0 m must be available.
IPA can only assist you with exiting a parking
space if you have parked the vehicle parallel to
the direction of travel using IPA.
WARNING
•IPA is only an aid. It is not a substitute for
your attention to the immediate surround-
ings. The responsibility for safe maneuver-
ing and parking remains with you.
•Make sure that no persons, animals or ob-
jects are in the maneuvering range.
•When the parking sensor system is deacti-
vated, IPA is also unavailable.
•While parking or pulling out of a parking
space, the vehicle swings out and can drive
onto areas of the oncoming lane. This could
cause you to collide with other road users.
There is a risk of an accident.
•Pay attention to other road users. Stop the
vehicle if necessary or cancel the IPA park-
ing procedure.
1. Start the engine.
2. Release the electric parking brake.
3. Switch on the turn signal in the direction you are pulling away.
4. Vehicles with automatic transmission: shift
the transmission to position D or R
The [Start Park Assist? Yes: OK No:]
message appears in the vehicle information
display.
5. To cancel the procedure: press the
button on the steering wheel or pull away
or
6. To exit a parking space using IPA: press the button on the steering wheel The Park
Assist [Observe surroundings] message ap-
pears in the display.
7. Release the steering wheel.
8.
Pull away, being ready to brake at all times Do
not exceed a maximum speed of approxi-
mately 5 MPH (10 km/h) when exiting a park-
ing space. Otherwise, IPA will be canceled.
WARNING
While parking or pulling out of a parking
space, the vehicle swings out and can drive
onto areas of the oncoming lane. This could
cause you to collide with other road users.
There is a risk of an accident.
9. Depending on the message or as required, shift the transmission to position D or R.
IPA immediately steers in the other direc-
tion. The [Observe surroundings] message
appears in the display.
NOTE
You will achieve the best results by waiting
for the steering procedure to complete before
pulling away.
If you back up after activation, the steering
wheel is moved to the straight-ahead posi-
tion.
10. Drive forward and back up as prompted by the parking sensor system warning dis-
plays, several times if necessary.
Once you have exited the parking space com-
pletely, the steering wheel is moved to the
straight-ahead position. You hear a tone and
the [Park Assist switched off] message appears
in the display. You will then have to steer and
5-72Starting and driving

merge into traffic on your own. The parking
sensor system is still available. You can take
over the steering before the vehicle has exited
the parking space completely. This is useful, for
example when you recognise that it is already
possible to pull out of the parking space.
CANCELING IPA
Stop the movement of the steering wheel or
steer yourself. IPA will be immediately can-
celed. The [Park Assist canceled] message ap-
pears in the vehicle information display.
or
Press the parking sensor system OFF switch.
The parking sensor system is switched off and
IPA is immediately canceled The [Park Assist
canceled] message appears in the vehicle infor-
mation display.IPA is canceled automatically if:
•The electric parking brake is applied
•Parking using IPA is no longer possible
•You are driving faster than 5 MPH (10 km/h)
•A wheel spins and VDC intervenes or fails.
Thewarning light lights up in the
combination meter.
A warning tone sounds. The parking symbol
disappears and the vehicle information display
shows the [Park Assist canceled] message.
When IPA is canceled, you must steer again
yourself.
WARNING
•The parking sensor system is a convenience
but it is not a substitute for proper parking.
Always look around and check that it is safe
to do so before parking. Always move
slowly.
•Read and understand the limitations of the
parking sensor system as contained in this
section. Inclement weather may affect the
function of the parking sensor system; this
may include reduced performance or a false
activation.
•This system is not designed to prevent con-
tact with small or moving objects.
•The system is designed as an aid to the
driver in detecting large stationary objects
to help avoid damaging the vehicle. The
system will not detect small objects below
the bumper, and may not detect objects that
are too close to the bumper or on the
ground.
•If your vehicle sustains damage to the bum-
per fascia, leaving it misaligned or bent, the
sensing zone may be altered causing inac-
curate measurement of obstacles or false
alarms.
PARKING SENSOR SYSTEM (IF EQUIPPED)
Starting and driving5-73

•Shift to position D (Drive), or R (Reverse) on
vehicles with automatic transmission
•Release the electric parking brake
The parking sensor system is deactivated at
speeds above 10 MPH (16 km/h). It is reacti-
vated at lower speeds.
The parking sensor system is deactivated for
the rear area when you establish an electrical
connection between your vehicle and a trailer.
RANGE OF THE SENSORS
The parking sensor system does not take into
account obstacles located:
•Below the detection range, e.g. persons,
animals or objects.
•Above the detection range, e.g. overhanging
loads, tail sections or loading ramps of
goods vehicles.
The sensors must be free of dirt, ice and slush.
Otherwise, they may not function correctly.
Clean the sensors regularly, taking care not to
scratch or damage them.
PARKING SENSOR SYSTEM OFF
SWITCH
The parking sensor system OFF switch2on
the lower side of the instrument panel allows
the driver to turn the parking sensor system on
and off. To turn the parking sensor system on
and off, the ignition switch must be in the ON
position. The indicator light
1on the switch
will illuminate when the system is turned off.
The parking sensor system will turn on auto-
matically when the ignition switch is turned
from the OFF position to the ON position.
NIC2635
Starting and driving5-79

Wheels and Tiresin the9. Maintenance and
Schedules section.)
– For detailed information, see Wheels and
tires in the 8. Do-it-yourself section.
The Anti-lock Braking System (ABS) controls the
brakes so the wheels do not lock during hard
braking or when braking on slippery surfaces.
The system detects the rotation speed at each
wheel and varies the brake fluid pressure to
prevent each wheel from locking and sliding. By
preventing each wheel from locking, the system
helps the driver maintain steering control and
helps to minimize swerving and spinning on
slippery surfaces.
Using system
Depress the brake pedal and hold it down.
Depress the brake pedal with firm steady pres-
sure, but do not pump the brakes. The ABS will
operate to prevent the wheels from locking up.
Steer the vehicle to avoid obstacles.
WARNING
Do not pump the brake pedal. Doing so may
result in increased stopping distances.
Self-test feature
The ABS includes electronic sensors, electric
pumps, hydraulic solenoids and a computer.
The computer has a built-in diagnostic feature
that tests the system each time you start the
engine and move the vehicle at a low speed in
forward or reverse. When the self-test occurs,
you may hear a “clunk” noise and/or feel a
pulsation in the brake pedal. This is normal and
does not indicate a malfunction. If the computer
senses a malfunction, it switches the ABS off
and illuminates the ABS warning light on the
instrument panel. The brake system then oper-
ates normally, but without anti-lock assistance.
If the ABS warning light illuminates during the
self-test or while driving, have the vehicle
checked. It is recommended you visit an
INFINITI retailer for this service.
Normal operation
The ABS operates at speeds above 3 to 6 MPH
(5 to 10 km/h). The speed varies according to
road conditions.
When the ABS senses that one or more wheels
are close to locking up, the actuator rapidly
applies and releases hydraulic pressure. This
action is similar to pumping the brakes very
quickly. You may feel a pulsation in the brake
pedal and hear a noise from under the hood or
feel a vibration from the actuator when it is
operating. This is normal and indicates that the
ABS is operating properly. However, the pulsa-
tion may indicate that road conditions are haz-
ardous and extra care is required while driving.
Starting and driving5-89

The Vehicle Dynamic Control (VDC) system uses
various sensors to monitor driver inputs and
vehicle motion. Under certain driving condi-
tions, the VDC system helps to perform the
following functions.
•Controls brake pressure to reduce wheel slip
on one slipping drive wheel so power is
transferred to a non slipping drive wheel on
the same axle.
•Controls brake pressure and engine output
to reduce drive wheel slip based on vehicle
speed (traction control function).
•Controls brake pressure at individual wheels
and engine output to help the driver maintain
control of the vehicle in the following condi-
tions:– understeer (vehicle tends to not follow the steered path despite increased steering
input)
– oversteer (vehicle tends to spin due to certain road or driving conditions).
The VDC system can help the driver to maintain
control of the vehicle, but it cannot prevent loss
of vehicle control in all driving situations. When the VDC system operates, the VDC warn-
ing light in the instrument panel flashes so note
the following:
•The road may be slippery or the system may
determine some action is required to help
keep the vehicle on the steered path.
•You may feel a pulsation in the brake pedal
and hear a noise or vibration from under the
hood. This is normal and indicates that the
VDC system is working properly.
•Adjust your speed and driving to the road
conditions.
See Vehicle Dynamic Control (VDC) warning
light in the 2. Instruments and controls sec-
tion.
If a malfunction occurs in the system, the VDC
warning light
illuminates in the instrument
panel. The VDC system automatically turns off.
WARNING
•The VDC system is designed to help the
driver maintain stability but does not pre-
vent accidents due to abrupt steering opera-
tion at high speeds or by careless or danger-
ous driving techniques. Reduce vehicle
speed and be especially careful when driv- ing and cornering on slippery surfaces and
always drive carefully.
•Do not modify the vehicle’s suspension. If
suspension parts such as shock absorbers,
struts, springs, stabilizer bars, bushings
and wheels are not INFINITI recommended
for your vehicle or are extremely deterio-
rated, the VDC system may not operate
properly. This could adversely affect vehicle
handling performance, and the VDC warning
light
may illuminate.
•If brake related parts such as brake pads,
rotors and calipers are not INFINITI recom-
mended or are extremely deteriorated, the
VDC system may not operate properly and
the VDC warning light
may illuminate.
•If engine control related parts are not
INFINITI recommended or are extremely de-
teriorated, the VDC warning light
may
illuminate.
•When driving on extremely inclined sur-
faces such as higher banked corners, the
VDC system may not operate properly and
the VDC warning light
may illuminate.
Do not drive on these types of roads.
•When driving on an unstable surface such
as a turntable, ferry, elevator or ramp, the
VEHICLE DYNAMIC CONTROL (VDC)
SYSTEM
5-90Starting and driving

will flash for approximately 1 minute. The
light will remain on after 1 minute. It is rec-
ommended you Contact an INFINITI retailer
as soon as possible for tire replacement
and/or system resetting.
•Replacing tires with those not originally
specified by INFINITI could affect the proper
operation of the TPMS.
•If you used Emergency Tire Sealant to repair
a minor tire puncture, the TPMS sensor
should be checked when repairing or re-
placing the tire. It is recommended you visit
an INFINITI retailer for this service.
The Tire Pressure Monitoring System (TPMS)
monitors tire pressure of all tires. When the low
tire pressure warning light is lit, and a tire
pressure-related warning (if equipped) appears
in the vehicle information display, one or more
of your tires is significantly under-inflated. If
the vehicle is being driven with low tire pres-
sure, the TPMS will activate and warn you of it
by the low tire pressure warning light (in the
meter panel). This system will activate only
when the vehicle is driven at speeds above 16
MPH (25 km/h). For more details about the TPMS, see
Tire
Pressure Monitoring System (TPMS) in the
5. Starting and driving section.
STOPPING VEHICLE
WARNING
•Be sure to apply the parking brake firmly.
•Be sure that P (Park) is engaged.
•Never change tires when the vehicle is on a
slope, ice or slippery area. This is hazard-
ous.
•Never change tires when the oncoming traf-
fic is close to your vehicle. Call for profes-
sional road assistance.
1. Safely move the vehicle off the road away from traffic.
2. Turn on the hazard indicator flasher lights.
3. Park on a level surface.
4. Apply the parking brake.
5. Press the P (Park) button.
6. Turn off the engine. 7. Open the hood and set up the triangle
reflector (if equipped):
•To warn other traffic.
•To signal professional road assistance
personnel that you need assistance.
8. Have all passengers get out of the vehicle and stand in a safe place, away from other
traffic and clear of the vehicle.
In case of emergency6-3