turn signal INFINITI QX30 2017 User Guide

Active light function
The active light function is a system that moves
the headlights according to the steering move-
ments of the front wheels. In this way relevant
areas remain illuminated while you are driving.
This helps you to recognize pedestrians, cy-
clists and animals. It is active when the lights
are switched on.
Cornering light function
The cornering light function improves the illu-
mination of the road over a wide angle in the
direction you are turning, enabling better vis-
ibility in tight bends, for example. It can only be
activated when the low-beam headlights are
switched on. It is active if you are driving at
speeds below 25 MPH (40 km/h) and switch on
the turn signal or turn the steering wheel.
The cornering light function may remain lit for a
short time, but is automatically switched off
after no longer than three minutes.
Freeway mode
Freeway mode adjusts the light beam to reduce
the amount of light that shines on the opposite
lane of the freeway, and oncoming traffic.
Freeway mode is active if you are driving at a
speed above 68 MPH (110 km/h) and do not
make any large steering movements for at least
3300 ft (1000 m) or if you are driving at a speed
above 81 MPH (130 km/h).
It is not active if you are driving at speeds below
50 MPH (80 km/h) following activation.
NSD593NSD592NSD594
2-66Instruments and controls

4. Position the end of your hand-held transmit-ter
52–8 inches (5–20 cm) away from the
HomeLink® surface, keeping the
HomeLink® indicator light
1in view.
5. Press and hold button
6on the hand held
transmitter until indicator lamp
1lights up
green. When indicator lamp
1: lights up
green: programing is finished.
When indicator lamp
1flashes green: pro-
graming was successful. The next step is to
synchronize the rolling code.
6. Release button
6on the hand held trans-
mitter
5for the garage door drive system.
If indicator lamp
1lights up red: repeat the
programing procedure for the corresponding
button on the rear-view mirror. When doing
so, vary the distance between the hand held
transmitter
5and the rear-view mirror.
The required distance between the hand
held transmitter
5and the integrated ga-
rage door opener depends on the garage
door drive system. Several attempts might
be necessary. You should test every position
for at least 25 seconds before trying another
position.
Synchronizing the rolling code
If the garage door system uses a rolling code,
you will also have to synchronize the garage
door system with the integrated garage door
opener in the rear-view mirror. To do this you
will need to use the programing button on the
door drive control panel. The programing button
may be positioned at different locations de-
pending on the manufacturer. It is usually lo-
cated on the door drive unit on the garage
ceiling.
Familiarize yourself with the garage door drive
operating instructions before carrying out the
following steps.
Your vehicle must be within reach of the garage
door or gate opener drive. Make sure that
neither your vehicle nor any persons/ objects
are present within the sweep of the door or
gate.
1. Turn the ignition key to the ON position.
2. Get out of the vehicle.
3. Press the programing button on the door drive unit.
Usually, you now have 30 seconds to initiate
the next step.
4. Get into the vehicle. 5. Press previously programed button
2,3or4on the HomeLink® until the door
closes.
The rolling code synchronization is then com-
plete.
If you live in Canada
Canadian radio frequency laws require a break
(or interruption) of the transmission signals
after broadcasting for a few seconds. Therefore,
these signals may not last long enough for the
integrated garage door opener. The signal is not
recognized during programing. Comparable
with Canadian law, some U.S. garage door
openers also feature a break.
Proceed as follows:
•If you live in Canada
•If you have difficulties programing the ga-
rage door opener (regardless of where you
live) when using the programing steps.
1. Press and hold one of buttons
2to4on
the HomeLink®. After a short time, indicator
lamp
1lights up yellow.
2. Release the button. Indicator lamp
1flashes yellow.
2-88Instruments and controls

3. Press button6of the hand held transmitter
5for two seconds, then release it for two
seconds.
4. Press button
6again for two seconds.
5. Repeat this sequence on button
6of the
hand held transmitter
5until indicator
lamp
1lights up green.
When indicator lamp
1lights up green:
programing is finished.
When indicator lamp
1flashes green: pro-
graming was successful. The next step is to
synchronize the rolling code.
6. Release button
6of the hand held trans-
mitter
5for the garage door drive.
If indicator lamp
1lights up red: repeat the
programing process for the corresponding
button on the rear-view mirror. When doing
so, vary the distance between the hand held
transmitter
5and the rear-view mirror.
The required distance between the hand
held transmitter
5and the HomeLink®
depends on the garage door drive system.
Several attempts might be necessary. You
should test every position for at least 25
seconds before trying another position.
PROGRAMMING TROUBLE DIAGNOSIS
If the HomeLink® does not quickly learn the
hand-held transmitter information:
•Check the transmitter frequency used by
garage door drive hand-held transmitter
5and whether it is supported. The transmitter
frequency can usually be found on the back
of the garage door drive hand-held transmit-
ter. HomeLink® is compatible with devices
that have units which operate in the fre-
quency range of 280 to 433 MHz.
•Replace the hand-held transmitter5batter-
ies with new batteries.
This increases the likelihood that the hand-
held transmitter
5will transmit a strong
and precise signal to the HomeLink®.
•When programing, hold the hand-held trans-
mitter
5at varying distances and angles
from the button which you are programing.
Try various angles at a distance between 2
and 12 inches (5 to 30 cm) or at the same
angle but at varying distances.
•If another hand-held transmitter is available
for the same garage door drive, repeat the
same programing steps with this hand-held
transmitter
5. Before performing these
steps, make sure that new batteries have been installed in the hand-held transmitter
5.
•Note that some hand-held transmitters only
transmit for a limited amount of time (the
indicator lamp on the hand-held transmitter
goes out). Press button
6on remote hand-
held transmitter
5again before transmis-
sion ends.
•Align the antenna cable of the garage door
opener unit. This can improve signal
reception/ transmission.
If you have any questions or are having diffi-
culty programming your HomeLink® buttons,
refer to the HomeLink® web site at:
www.homelink.com or 1-800-355-3515.
OPERATING THE HOMELINK®
UNIVERSAL TRANSCEIVER
The HomeLink® Universal Transceiver, after it is
programmed, can be used to activate the pro-
grammed device.
1. Turn the ignition key to the ON position.
2. Press button
2,3or4which you have
programed to operate the garage door.
Garage door system with a fixed code: indi-
cator lamp
1lights up green
Instruments and controls2-89

Garage door system with a rolling code:
indicator lamp
1flashes green.
The transmitter will transmit a signal as long as
the button is pressed. The transmission is
halted after a maximum of ten seconds and
indicator lamp
1lights up yellow. Press button
2,3or4again if necessary.
For convenience, the hand-held transmitter of
the device may also be used at any time.
CLEARING THE PROGRAMMED
INFORMATION
Make sure that you clear the memory of the
integrated garage door opener before selling
the vehicle.
1. Turn the ignition key to the ON position.
2. Press and hold buttons
2and4.
The indicator lamp initially lights up yellow
and then green.
3. Release buttons
2and4.
The memory of the integrated garage door
opener in the rear-view mirror is cleared.
IF YOUR VEHICLE IS STOLEN
If your vehicle is stolen, you should change the
codes of any non-rolling code device that has
been programmed into HomeLink®. Consult the
Owner’s Manual of each device or call the
manufacturer of those devices for additional
information or contact an INFINITI retailer.
2-90Instruments and controls

When the doors are locked using one of the
following methods, the doors cannot be opened
using the inside or outside door handles. The
doors must be unlocked to open the doors.
WARNING
•Before opening any door, always look for
and avoid oncoming traffic.
•Do not leave children unattended inside the
vehicle. They could unknowingly activate
switches or controls. Unattended children
could become involved in serious accidents.
•Do not leave children or adults who would
normally require the assistance of others
alone in your vehicle. Pets should also not
be left alone. They could accidentally injure
themselves or others through inadvertent
operation of the vehicle. Also, on hot, sunny
days, temperatures in a closed vehicle
could quickly become high enough to cause
severe or possibly fatal injuries to people or
animals.
LOCKING WITH THE KEY
1Locks the vehicle.
2Unlocks the vehicle.
3Panic button.
If you do not open the vehicle within approxi-
mately 40 seconds of unlocking, the vehicle will
lock again and protection against theft is reac-
tivated.
To lock centrally, press button
1. The key
centrally locks:
•Doors
•Lift gate
•Fuel filler lid
When unlocking, the turn signals flash once
When locking, they flash three times.
Intelligent key
You can combine the Intelligent Key functions
with the functions of a conventional key. Unlock
the vehicle by using Intelligent key function, for
instance, and lock it using the
button on
the key.
The driver’s door and the door at which the
handle is used, must both be closed. The key
must be outside the vehicle. When locking or
unlocking with Intelligent key, the distance
between the key and the corresponding door
handle must not be greater than 1 m.
NPA1493
DOORS
3-4Pre-driving checks and adjustments

To unlock the vehicle:touch the inner surface of
the door handle.
To lock the vehicle: touch sensor surface
1.or
2.
Make sure that you do not touch the inner
surface of the door handle.
Convenience closing feature: touch recessed
sensor surface
1for an extended period. (See
Convenience closing feature in the
2. Instruments and controls section).To unlock the lift gate: press the lift gate switch
1.
When unlocking, the turn signals flash once
When locking, they flash three times.
NOTE
When the locator lighting is activated, it lights
up when it is dark after the vehicle is unlocked
with the intelligent key (see separate operating
instructions).
You can also set an audible signal to con firm
that the vehicle has been locked. The audible
signal can be activated or deactivated using the
on-board computer (see Activating/
deactivating the acoustic locking confirmation
in the 2. Instruments and controls section)LOCKING WITH THE MECHANICAL KEY
The driver’s door can be locked/unlocked from
outside using the mechanical key if the battery
is dead.
To lock the door, insert the mechanical key into
the driver’s door key cylinder and turn it to-
wards the front of the vehicle
1.
To unlock the door, turn the key towards the
rear of the vehicle
2.
See Mechanical key earlier in this section for
instructions on accessing the Intelligent Key
system mechanical key.
NOTE
The alarm system will be triggered when the
door is opened using the mechanical key (alarm
equipped models). To stop the alarm, turn the
NPA1489NPA1479SPA2602Z
Pre-driving checks and adjustments3-5

DOOR LOCKS/UNLOCKS PRECAUTION
•Do not touch the door handle request switch
with the Intelligent Key held in your hand as
illustrated. The close distance to the door
handle will cause the Intelligent Key system
to have difficulty recognizing that the Intelli-
gent Key is outside the vehicle.
•To prevent the Intelligent Key from being left
inside the vehicle, make sure you carry the
Intelligent Key
INFINITI INTELLIGENT KEY OPERATION
You can lock or unlock the doors without taking
the Intelligent Key out of your pocket or bag.
When you carry the Intelligent Key with you, you
can lock or unlock all doors by pushing the door
handle request switch within the range of op-
eration.
Locking doors
1. Push the P (Park) button to engage the P(Park) position, place the ignition switch in
the LOCK position and make sure you carry
the Intelligent Key with you.
2. Close all doors.
3. Touch any sensor surface
1or2.
4. All doors and the lift gate will lock. 5. The turn signals flash three times.
NOTE
•Doors do not lock by pushing the door
handle request switch while any door is
open. However, doors lock with the mechani-
cal key even if any door is open.
•The driver’s door and the door at which the
handle is used, must both be closed.
•The doors may not lock when the Intelligent
Key is in the same hand that is operating the
request switch to lock the door. Put the
Intelligent Key in a purse, pocket or your
other hand.
CAUTION
•When locking the doors using the request
switch, make sure to have the Intelligent
Key in your possession before operating the
request switch to prevent the Intelligent
Key from being left in the vehicle.
•The request switch is operational only when
the Intelligent Key has been detected by the
Intelligent Key system.
WPD0375ZNPA1489
3-10Pre-driving checks and adjustments

Unlocking doors
1. Carry the Intelligent Key.
2. Touch the inner surface of the door handle.
3. All doors and the lift gate will unlock.
4. The turn signals flash once.
CHANGING THE SETTINGS OF THE
LOCKING SYSTEM
You can change the settings of the locking
system. This means that only the driver’s door
and the fuel-filler lid are unlocked when the
vehicle is unlocked. This is useful if you fre-
quently travel alone.
To change the setting:simultaneously press the
andbuttons for approximately 6
seconds.
NOTE
If the setting of the locking system is changed
within the signal range of the vehicle, pressing
the
andbutton will lock or unlock
the vehicle. The key now functions as follows:
To unlock the driver’s door:
press the
button once.
To unlock centrally:press the
button
twice.
To lock centrally: press the
button.
The Intelligent key function is changed as fol-
lows:
To unlock the driver’s door: touch the inner
surface of the door handle on the driver’s door.
To unlock centrally: touch the inner surface of
the door handle on the front passenger door or
the rear door.
To lock centrally: touch the outer sensor surface
on one of the door handles
To restore the factory settings: simultaneously
press the
andbutton for approxi-
mately 6 seconds.
Pre-driving checks and adjustments3-11

AUDIO OPERATION PRECAUTIONS
WARNING
•The driver must not attempt to operate the
audio system while the vehicle is in motion,
so that full attention may be given to vehicle
operation.
•Park the vehicle in a safe location and apply
the parking brake before operating the au-
dio system and playing movies (if
equipped).
CAUTION
•Operate the audio system only when the
vehicle engine is running. Operating the au-
dio system for extended periods of time
with the engine turned off can discharge the
vehicle battery.
•Do not allow the system to get wet. Exces-
sive moisture such as spilled liquids may
cause the system to malfunction.
Radio
Turn the ignition switch to the ACC or ON
position before turning on the radio. If you
listen to the radio when the engine is not
running, the ignition switch should be pushed
to the ACC position.
Radio reception is affected by station signal
strength, distance from radio transmitter, build-
ings, bridges, mountains and other external
influences. Intermittent changes in reception
quality are normally caused by these external
influences.
Using a cellular phone in or near the vehicle may
influence radio reception quality.
Radio reception
Your radio system is equipped with state-of-the-
art electronic circuits to enhance radio recep-
tion. These circuits are designed to extend
reception range, and to enhance the quality of
that reception.
However there are some general characteristics
of both FM and AM radio signals that can affect
radio reception quality in a moving vehicle,
even when the best quality equipment is used.
These characteristics are completely normal in
a given reception area, and do not indicate any
malfunction in your radio system.Reception conditions will constantly change
because of vehicle movement. Buildings, ter-
rain, signal distance and interference from
other vehicles can adversely affect ideal recep-
tion. Described below are some of the factors
that can affect radio reception.
Some cellular phones or other devices may
cause interference or a buzzing noise to come
from the audio system speakers. Storing the
device in a different location may reduce or
eliminate the noise.
AUDIO SYSTEM (IF EQUIPPED)
4-52Display screen, heater and air conditioner, and audio system

2[Source]: Touch to switch to the source
select screen. SeeSelecting audio
source later in this section
3[Control]: Touch to display the control
screen. See Radio Controls later in this
section
4HD Radio reception status indicator (for
AM and FM):
The icon is displayed when HD Radio digital
signal is received. The icon flashes when
the radio is acquiring the digital signal but
the sound output is not yet in the HD mode.
5Radio band indicator: The currently se-
lected radio band (AM, FM or SXM) is dis-
played.
6Reception information display: Reception
information available at the time such as
frequency, station/channel name, etc.. are
displayed.
On the SXM screen, touch this area to
display the category list.
736 stations/channels can be registered in
the preset list.
See Presetting later in this section. NOTE
HD Radio reception needs to be activated to re-
ceive HD Radio broadcasts. This enables you to
receive radio broadcasts digitally (where avail-
able), providing a better quality sound with clear
reception. When this feature is not activated or
HD Radio broadcasts are not available, you will
receive analog radio (AM/FM broadcasts).
Radio source control
There are 2 elements used in the preset list area
that are associated with radio source:
1Highlight for INFINITI controller operation.
2(With triangle) Indicator of current se-
lected preset station.
Radio operation
Radio activation and band selection:
Push
or select the preferred radio band
(AM, FM or SXM) from the audio source list to
turn on the radio. Each time is pushed,
the radio band will change.
For details, see Selecting audio source later in
this section.
NAA1717
Display screen, heater and air conditioner, and audio system4-67