automatic transmission INFINITI QX30 2017 Owner's Guide

–The ICC system has been deactivated
with the cruise control lever, e. g. by a
vehicle occupant.
– The accelerator pedal has been de-
pressed, e.g. by a vehicle occupant.
For further information on deactivating the ICC
system, see ICC switch (cruise control lever)
earlier in this section
If the ICC system detects that the vehicle in
front is stopping, it brakes your vehicle until it
is stationary (within the braking limitations of
the system).
Once your vehicle is stationary, it remains
stationary and you do not need to depress the
brake.
NOTE
•After a short period, the vehicle is secured by
the electric parking brake, thus relieving the
service brake.
•Depending on the specified minimum dis-
tance, your vehicle will come to a standstill
at a sufficient distance behind the vehicle in
front. The specified minimum distance is set
using the control on the cruise control lever. The electric parking brake secures the vehicle
automatically if the ICC system is activated
when the vehicle is stationary and:
•A system fault occurs.
•The power supply is insufficient.
If a malfunction in the electric parking brake
occurs, then the transmission may also be
shifted into position P (Park) automatically.
How to change the set distance to
the vehicle ahead
The distance to the vehicle ahead can be se-
lected at any time depending on the traffic
conditions.
To increase the distance to the vehicle ahead,
turn the knob
3toward the rear2. To de-
crease the distance to the vehicle ahead, turn
the knob
3toward the front1.
You can see this distance in the vehicle infor-
mation display.
The distance to the vehicle ahead will change
according to the vehicle speed. The higher the
vehicle speed, the longer the distance.
NSD583A
Starting and driving5-53

•The border of the parking space must not be
too wide, as the position of the vehicle must
not exceed an angle of 45 degrees to the
starting position as it is manoeuvred into the
parking space.
•A total front and back maneuvering distance
of at least 1.0 m must be available.
IPA can only assist you with exiting a parking
space if you have parked the vehicle parallel to
the direction of travel using IPA.
WARNING
•IPA is only an aid. It is not a substitute for
your attention to the immediate surround-
ings. The responsibility for safe maneuver-
ing and parking remains with you.
•Make sure that no persons, animals or ob-
jects are in the maneuvering range.
•When the parking sensor system is deacti-
vated, IPA is also unavailable.
•While parking or pulling out of a parking
space, the vehicle swings out and can drive
onto areas of the oncoming lane. This could
cause you to collide with other road users.
There is a risk of an accident.
•Pay attention to other road users. Stop the
vehicle if necessary or cancel the IPA park-
ing procedure.
1. Start the engine.
2. Release the electric parking brake.
3. Switch on the turn signal in the direction you are pulling away.
4. Vehicles with automatic transmission: shift
the transmission to position D or R
The [Start Park Assist? Yes: OK No:]
message appears in the vehicle information
display.
5. To cancel the procedure: press the
button on the steering wheel or pull away
or
6. To exit a parking space using IPA: press the button on the steering wheel The Park
Assist [Observe surroundings] message ap-
pears in the display.
7. Release the steering wheel.
8.
Pull away, being ready to brake at all times Do
not exceed a maximum speed of approxi-
mately 5 MPH (10 km/h) when exiting a park-
ing space. Otherwise, IPA will be canceled.
WARNING
While parking or pulling out of a parking
space, the vehicle swings out and can drive
onto areas of the oncoming lane. This could
cause you to collide with other road users.
There is a risk of an accident.
9. Depending on the message or as required, shift the transmission to position D or R.
IPA immediately steers in the other direc-
tion. The [Observe surroundings] message
appears in the display.
NOTE
You will achieve the best results by waiting
for the steering procedure to complete before
pulling away.
If you back up after activation, the steering
wheel is moved to the straight-ahead posi-
tion.
10. Drive forward and back up as prompted by the parking sensor system warning dis-
plays, several times if necessary.
Once you have exited the parking space com-
pletely, the steering wheel is moved to the
straight-ahead position. You hear a tone and
the [Park Assist switched off] message appears
in the display. You will then have to steer and
5-72Starting and driving

•Shift to position D (Drive), or R (Reverse) on
vehicles with automatic transmission
•Release the electric parking brake
The parking sensor system is deactivated at
speeds above 10 MPH (16 km/h). It is reacti-
vated at lower speeds.
The parking sensor system is deactivated for
the rear area when you establish an electrical
connection between your vehicle and a trailer.
RANGE OF THE SENSORS
The parking sensor system does not take into
account obstacles located:
•Below the detection range, e.g. persons,
animals or objects.
•Above the detection range, e.g. overhanging
loads, tail sections or loading ramps of
goods vehicles.
The sensors must be free of dirt, ice and slush.
Otherwise, they may not function correctly.
Clean the sensors regularly, taking care not to
scratch or damage them.
PARKING SENSOR SYSTEM OFF
SWITCH
The parking sensor system OFF switch2on
the lower side of the instrument panel allows
the driver to turn the parking sensor system on
and off. To turn the parking sensor system on
and off, the ignition switch must be in the ON
position. The indicator light
1on the switch
will illuminate when the system is turned off.
The parking sensor system will turn on auto-
matically when the ignition switch is turned
from the OFF position to the ON position.
NIC2635
Starting and driving5-79

SWITCHING OFF THE ENGINE
WARNING
The automatic transmission switches to posi-
tion N (Neutral) when you switch off the en-
gine. The vehicle may roll away. There is a risk
of an accident.
After switching off the engine, always switch
to position P (Park). Prevent the parked vehicle
from rolling away by applying the parking
brake.
Procedure
1. Apply the electric parking brake.
2. Shift the transmission to position P (Park).
3.With the key: turn the key to the position OFF
in the ignition switch and remove it The
immobilizer is activated.
If you switch the engine off with the transmis-
sion in position R (Reverse) or D (Drive), the
automatic transmission shifts to N (Neutral)
automatically.
With the key: if you then open the driver’s door
or the front-passenger door or remove the key
from the ignition, the automatic transmission
shifts to P (Park) automatically. If you want the automatic transmission to re-
main in neutral N (Neutral), e.g. when having
the vehicle cleaned in an automatic car wash
with a towing system:
With the key
:
1. Switch the ignition on.
2. Depress the brake pedal and keep it de-
pressed.
3. Shift to N (Neutral).
4. Release the brake pedal.
5. Release the electric parking brake.
6. Switch off the ignition and leave the key in the ignition switch.
EXTENDED PARKING
If you leave the vehicle parked up for longer
than four weeks, the battery may be damaged
by exhaustive discharging.
If you leave the vehicle parked up for longer
than six weeks, it may suffer from lack of use.
Visit an INFINITI retailer and seek advice
NOTE
You can obtain information about trickle char-
gers from an INFINITI retailer. The electric power steering system is designed
to reduce the driver effort required to steer the
vehicle.
WARNING
If during operation a fault is detected the fol-
lowing message will be displayed in the ve-
hicle information display along with an audible
warning tone.
[Power Steering Malfunction See Operators
Manual]
In conjunction with this warning, steering as-
sistance will no longer be provided by the sys-
tem.
The effort required to steer the vehicle will
increase. This will be most noticeable at low
speed and when performing a tight turning
maneuver.
Check whether you are able to provide the ex-
tra effort required.
If you are able to steer safely: Carefully drive on
to an INFINITI retailer.
If you are unable to steer safely: Do NOT drive
on. It is recommended you contact the nearest
INFINITI retailer for assistance.
ELECTRIC POWER STEERING SYSTEM
5-86Starting and driving

WARNING
•Never rely solely on the Hill Start Assist
(HSA) system to prevent the vehicle from
moving backward on a hill. Always drive
carefully and attentively. Depress the brake
pedal when the vehicle is stopped on a
steep hill. Be especially careful when
stopped on a hill on frozen or muddy roads.
Failure to prevent the vehicle from rolling
backwards may result in a loss of control of
the vehicle and possible serious injury or
death.
•The Hill Start Assist system is not designed
to hold the vehicle at a standstill on a hill.
Depress the brake pedal when the vehicle is
stopped on a steep hill. Failure to do so may
cause the vehicle to roll backwards and may
result in a collision or serious personal in-
jury.
•The Hill Start Assist system may not prevent
the vehicle from rolling backwards on a hill
under all load or road conditions. Always be
prepared to depress the brake pedal to pre-
vent the vehicle from rolling backwards.
Failure to do so may result in a collision or
serious personal injury.
•After a short time, hill start assist will no
longer brake your vehicle and it could rollaway There is a risk of an accident and in-
jury. Therefore, quickly move your foot from
the brake pedal to the accelerator pedal.
Never leave the vehicle when it is held by
hill start assist.
Hill start assist helps you when pulling away
forwards or in reverse on an uphill gradient. It
holds the vehicle for a short time after you have
removed your foot from the brake pedal. This
gives you enough time to move your foot from
the brake pedal to the accelerator pedal and
depress it before the vehicle begins to roll.
Hill start assist is not active if
•You are pulling away on a level road or a
downhill gradient.
•On vehicles with automatic transmission, the
transmission is in position N.
•The electric parking brake is applied.
•VDC is malfunctioning.
FREEING A FROZEN DOOR LOCK
To prevent a door lock from freezing, apply
deicer through the key hole. If the lock becomes
frozen, heat the key before inserting it into the
key hole, or use the INFINITI Intelligent Key.
ANTIFREEZE
In the winter when it is anticipated that the
temperature will drop below 32°F (0°C), check
the antifreeze to assure proper winter protec-
tion. For additional information, see Engine
cooling system in the8. Do-it-yourself sec-
tion.
BATTERY
If the battery is not fully charged during ex-
tremely cold weather conditions, the battery
fluid may freeze and damage the battery. To
maintain maximum efficiency, the battery
should be checked regularly. For details, see
Battery in the8. Do-it-yourself section of this
manual.
DRAINING OF ENGINE COOLANT
If the vehicle is to be left outside without
antifreeze, drain the cooling system, including
the engine block. Refill before operating the
vehicle. For details, see Changing engine
HILL START ASSIST (HSA) COLD WEATHER DRIVING
Starting and driving5-93

CAUTION
•Always connect positive+to positive+and negative-to body ground (for ex-
ample, strut mounting bolt, engine lift
bracket, etc.) – not to the battery’s negative
-.
•Be sure that the jumper cables do not touch
moving parts in the engine compartment
and that the cable clamps do not contact
any other metal.
9. Start the engine of the other vehicle
Aand
let it run for a few minutes. Keep the engine
speed at about 2,000 rpm.
10. Start the engine of your vehicle
Bin the
normal way.
CAUTION
Do not keep the starter motor engaged for
more than 10 seconds. If the engine does not
start right away, place the ignition switch in
the OFF position and wait 10 seconds before
trying again.
11. After starting the engine of your vehicle, carefully disconnect the negative lead and
then the positive lead (
4→3→2→
1). 12. Remove and dispose of the cloth that was
used to cover the ventilator holes as it may
be contaminated with corrosive acid.
13. Install the ventilator caps (if equipped).
14. Close the hood.
NOTE
For models which incorporate the Idle Stop/
Start System:
•Ensure that the battery fitted is the special
battery that is enhanced with regard to the
charge-discharge capacity and life perfor-
mance. Avoid using any other battery for the
Idle Stop/Start System, as this may cause
early deterioration of the battery or a mal-
function of the Idle Stop/Start System. It is
recommended that a Genuine INFINITI bat-
tery is fitted. For more information, it is
recommended you contact an INFINITI re-
tailer.
•If the battery terminal is disconnected (for
battery replacement, etc.) and then recon-
nected, there may be some delay before the
Idle top/Start System reactivates. Do not attempt to start the engine by pushing
the vehicle.
CAUTION
•Automatic Transmission (AT) model cannot
be push-started or tow-started. Attempting
to do so may cause damage to the transmis-
sion.
•Three-way catalyst equipped models
should not be started by pushing. Attempt-
ing to do so may cause damage to the three-
way catalyst.
•Never try to start the vehicle by towing it;
when the engine starts, the forward surge
could cause the vehicle to collide with the
tow vehicle.
PUSH STARTING
6-12In case of emergency

Two-Wheel Drive (FWD) models
CAUTION
NEVER tow automatic transmission (DCT) mod-
els with the front wheels on the ground or with
all four wheels on the ground (forwards or
backwards), as this may cause serious and ex-
pensive damage to the transmission. If it is
necessary to tow the vehicle with the rear
wheels raised, always use towing dollies un-
der the front wheels.
Four-Wheel Drive (4WD) models
INFINITI recommends that towing dollies be
used under the front or rear wheels when
towing your vehicle or the vehicle be placed on
a flatbed tow truck as illustrated.
CAUTION
Never tow 4WD models with any of the wheels
on the ground. Doing so will cause serious and
expensive damage to the drivetrain.
Vehicle recovery (freeing a stuck
vehicle)
WARNING
To avoid vehicle damage, serious personal in-
jury or death when recovering a stuck vehicle:
•Contact a professional towing service to re-
cover the vehicle if you have any questions
regarding the recovery procedure.
•Tow chains or cables must be attached only
to the vehicle recovery hooks or main struc-
tural members of the vehicle.
•Do not use the vehicle tie downs to tow or
free a stuck vehicle.
•Only use devices specifically designed for
vehicle recovery and follow the manufactur-
er’s instructions.
•Always pull the recovery device straight out
from the front of the vehicle. Never pull at an
angle.
•Route recovery devices so they do not touch
any part of the vehicle except the attach-
ment point.
If your vehicle is stuck in sand, snow, or mud,
and the vehicle is unable to free itself without
NCE4504WD models
In case of emergency6-15

8 Do-it-yourself
Maintenance precautions..................8-2
Engine compartment check locations ...........8-3
2.0L Gasoline engine .................. .8-3
Engine cooling system ................... .8-3
Checking engine coolant level .............8-4
Changing engine coolant ................8-4
Engine oil ........................... .8-5
Checking engine oil level ................8-5
Changing engine oil .................. .8-5
Changing engine oil filter ................8-6
Automatic Transmission Fluid (ATF) ............8-7
Brake fluid .......................... .8-7
Window washer fluid .................... .8-8
Battery ............................ .8-9
Accessing Vehicle battery ...............8-10
Maintenance free battery ................8-10
Models with Idle Stop/Start System .........8-10
Battery replacement .................. .8-11
Reinitialisation procedure after battery
reconnection ...................... .8-12
Jump-starting ...................... .8-12
Drive belt .......................... .8-12
Spark plugs ..........................8-13
Air cleaner filter ...................... .8-13
Wiper blades .........................8-13 Cleaning
..........................8-13
Replacing front window wiper blades ........8-14
Replacing rear window wiper blade ..........8-15
Brakes ............................ .8-17
Self-adjusting brakes ..................8-17
Fuses ............................. .8-17
Before replacing a fuse .................8-17
Engine compartment .................. .8-17
Passenger compartment ................8-18
Intelligent key battery replacement ..........
.8-20
Checking the

battery ..................8-20
Replacing the battery ..................8-20
Lights ............................ .8-22
Exterior and interior lights ...............8-22
Replacement procedures ................8-24
Wheels and tires ..................... .8-26
Tire Pressure ...................... .8-26
Tire inflation pressure .................8-28
Tire labeling ...................... .8-28
Types of tires ..................... .8-30
Tire chains ....................... .8-31
Tire wear and damage .................8-31
Tire rotation ...................... .8-32
Replacing wheels and tires ..............8-32
Wheel balance ..................... .8-34

When performing any inspection or mainte-
nance work on your vehicle, always take care to
prevent serious accidental injury to yourself or
damage to the vehicle. The following are gen-
eral precautions which should be closely ob-
served.
WARNING
•Park the vehicle on a level surface, apply the
parking brake securely and block the
wheels to prevent the vehicle from moving.
Press the P (Park) button.
•Be sure the ignition switch is in the OFF
position when performing any parts re-
placement or repairs.
•Do not work under the hood while the en-
gine is hot. Always turn off the engine and
wait until it cools down.
•If you must work with the engine running,
keep your hands, clothing, hair and tools
away from moving fans, belts and any other
moving parts.
•It is advisable to secure or remove any loose
clothing and any jewelry, such as rings,
watches, etc. before working on your ve-
hicle.
•If you must run the engine in an enclosed
space such as a garage, be sure there is
proper ventilation for exhaust gases to es-
cape.
•Never get under the vehicle while it is sup-
ported by a jack.
•Keep smoking materials, flame and sparks
away from fuel and the battery.
•Never connect or disconnect either the bat-
tery or any transistorized component con-
nector while the ignition switch is in the ON
position.
•On gasoline engine models with the Multi-
port Fuel Injection system, the fuel filter and
fuel lines should be serviced by an INFINITI
retailer or qualified workshop because the
fuel lines are under high pressure even
when the engine is turned off.
•Your vehicle is equipped with an automatic
engine cooling fan. It may come on at any
time without warning, even if the ignition
switch is in the OFF position and the engine
is not running. To avoid injury, always dis-
connect the negative battery cable before
working near the fan.
•Always wear eye protection whenever you
work on your vehicle.
•Never leave the engine or the transmission
related component harness connector dis-
connected while the ignition switch is in the
ON position.
•Avoid direct contact with used engine oil
and coolant. Improperly disposed engine
oil, engine coolant, and/or other vehicle flu-
ids can hurt the environment. Always con-
form to local regulations for disposal of ve-
hicle fluids.
This “ 8. Do-it-yourself” section provides in-
structions regarding only those items which are
relatively easy for an owner to perform.
You should be aware that incomplete or im-
proper servicing may result in operating diffi-
culties or excessive emissions, and could affect
your warranty coverage. If in doubt about any
servicing, it is recommended you have it done by
an INFINITI retailer.
MAINTENANCE PRECAUTIONS
8-2Do-it-yourself

5. Wipe the engine oil filter sealing surface witha clean rag.
CAUTION
•Be sure to remove any old gasket material
remaining on the sealing surface of the en-
gine. Failure to do so could lead to an oil
leak and engine damage.
•The dipstick must be inserted in place to
prevent oil spillage from the dipstick hole
when filling the engine with oil.
6. Coat the gasket on the new filter with clean engine oil.
7. Screw on the oil filter until a slight resis- tance is felt, then tighten an additional
2/3 turn. Engine oil filter tightening torque:
19 ft-lb, 25 N•m
8. Start the engine and check for leakage around the oil filter. Correct as required.
9. Turn the engine off and wait more than 10 minutes. Check the oil level. Add engine oil
if necessary. It is recommended that you visit an INFINITI
retailer if checking or replacement is required.
CAUTION
•Use only Shell DCT-M1 or equivalent. Do not
mix with other fluids.
•Using automatic transmission fluid other
than Shell DCT-M1 may cause deterioration
in driveability and automatic transmission
durability, and may damage the automatic
transmission. Damage caused by the use of
fluids other than as recommended is not
covered by the warranty.
WARNING
•Use only new fluid. Old, inferior, or contami-
nated fluid may damage the brake systems.
The use of improper fluids can damage the
brake system and affect the vehicle’s stop-
ping ability.
•Clean the filler cap before removing.
•Brake fluid is poisonous and should be
stored carefully in marked containers out of
the reach of children.
CAUTION
•Do not spill the fluid on painted surfaces.
This will damage the paint. If fluid is spilled,
wash with water.
NDI1599
AUTOMATIC TRANSMISSION FLUID (ATF) BRAKE FLUID
Do-it-yourself8-7