check engine light INFINITI QX30 2017 Owner's Guide

RADAR MAINTENANCE
The two radar sensor unitsAfor the BSW
system are located near the rear bumper. Al-
ways keep the area near the radar sensors
clean.
The radar sensors may be blocked by temporary
ambient conditions such as splashing water,
mist or fog.
The blocked condition may also be caused by
objects such as ice, frost or dirt obstructing the
radar sensors.
Check for and remove objects obstructing the
area around the radar sensors.
Do not attach stickers (including transparent
material), install accessories or apply addi-
tional paint near the radar sensors. Do not strike or damage the area around the
radar sensors. It is recommended you consult
an INFINITI retailer if the area around the radar
sensors is damaged due to a collision.
FCC NOTICE
For USA:
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause harm-
ful interference, and (2) this device must accept
any interference received, including interfer-
ence that may cause undesired operation.
NOTE
Changes or modification not expressly approved
by the party responsible for compliance could
void the user’s authority to operate the equip-
ment.
For Canada:
This device complies with Industry Canada
license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this
device may not cause harmful interference, and
(2) this device must accept any interference re-
ceived, including interference that may cause
undesired operation of the device.
Cruise control maintains a constant road speed
for you. It brakes automatically in order to avoid
exceeding the set speed. You must select a
lower gear in good time on long and steep
downhill gradients, especially if the vehicle is
laden or towing a trailer.WARNING
For vehicles with automatic transmission, you
need to have selected manual drive program M
(see
Manual drive program earlier in this sec-
tion). By doing so, you will make use of the
braking effect of the engine. This relieves the
load on the brake system and prevents the
brakes from overheating and wearing too
quickly.
Use cruise control only if road and traffic con-
ditions are appropriate for maintaining a steady
speed for a prolonged period. You can set the
cruise control at any road speed above 20 MPH
(30 km/h).
The speed indicated in the speedometer may
differ slightly from the set speed.
NAA1640
CRUISE CONTROL
5-44Starting and driving

PROBLEMS WITH PARKING SENSOR SYSTEM
ProblemPossible causes/consequences and solutions
Only the red segments in the
Parking Sensor System displays are
lit. You also hear a warning tone for
approximately two seconds.
The Parking Sensor System is then
deactivated and the indicator light
on the Parking Sensor System
button lights up. The Parking Sensor System has malfunctioned and has been
deactivated.
If problems persist, have the Parking Sensor System checked. It is
recommended you visit an INFINITI retailer for this service.
Only the red segments in the
parking sensor displays are lit. The
Parking Sensor System is then
deactivated. The parking sensors are dirty or there is interference.
•Clean the sensors.•Switch the ignition back on.
The problem may be caused by an external source of radio or ultrasound
waves.
See if the Parking Sensor System functions in a different location.
During the first 1,200 miles (2,000 km), follow
these recommendations to obtain maximum
engine performance and ensure the future reli-
ability and economy of your new vehicle. Failure
to follow these recommendations may result in
shortened engine life and reduced engine per-
formance.
•Avoid driving for long periods at constant
speed, either fast or slow, and do not run the
engine over 4,000 RPM.
•Do not accelerate at full throttle in any gear.
•Avoid quick starts.
•Avoid hard braking as much as possible.
•Do not tow a trailer for the first 500 mi (805
km). Your engine, axle or other parts could
be damaged.
You should also observe these notes on
break-in if the engine or parts of the drive train
on your vehicle have been replaced.
CAUTION
In certain driving and driving safety systems,
the sensors adjust automatically while a cer-
tain distance is being driven after the vehicle
has been delivered or after repairs. Full system
effectiveness is not reached until the end of
this teach-in process.
BREAK-IN SCHEDULE
Starting and driving5-81

Wheels and Tiresin the9. Maintenance and
Schedules section.)
– For detailed information, see Wheels and
tires in the 8. Do-it-yourself section.
The Anti-lock Braking System (ABS) controls the
brakes so the wheels do not lock during hard
braking or when braking on slippery surfaces.
The system detects the rotation speed at each
wheel and varies the brake fluid pressure to
prevent each wheel from locking and sliding. By
preventing each wheel from locking, the system
helps the driver maintain steering control and
helps to minimize swerving and spinning on
slippery surfaces.
Using system
Depress the brake pedal and hold it down.
Depress the brake pedal with firm steady pres-
sure, but do not pump the brakes. The ABS will
operate to prevent the wheels from locking up.
Steer the vehicle to avoid obstacles.
WARNING
Do not pump the brake pedal. Doing so may
result in increased stopping distances.
Self-test feature
The ABS includes electronic sensors, electric
pumps, hydraulic solenoids and a computer.
The computer has a built-in diagnostic feature
that tests the system each time you start the
engine and move the vehicle at a low speed in
forward or reverse. When the self-test occurs,
you may hear a “clunk” noise and/or feel a
pulsation in the brake pedal. This is normal and
does not indicate a malfunction. If the computer
senses a malfunction, it switches the ABS off
and illuminates the ABS warning light on the
instrument panel. The brake system then oper-
ates normally, but without anti-lock assistance.
If the ABS warning light illuminates during the
self-test or while driving, have the vehicle
checked. It is recommended you visit an
INFINITI retailer for this service.
Normal operation
The ABS operates at speeds above 3 to 6 MPH
(5 to 10 km/h). The speed varies according to
road conditions.
When the ABS senses that one or more wheels
are close to locking up, the actuator rapidly
applies and releases hydraulic pressure. This
action is similar to pumping the brakes very
quickly. You may feel a pulsation in the brake
pedal and hear a noise from under the hood or
feel a vibration from the actuator when it is
operating. This is normal and indicates that the
ABS is operating properly. However, the pulsa-
tion may indicate that road conditions are haz-
ardous and extra care is required while driving.
Starting and driving5-89

VDC warning lightmay illuminate. This
is not a malfunction. Restart the engine af-
ter driving onto a stable surface.
•If wheels or tires other than the INFINITI
recommended ones are used, the VDC sys-
tem may not operate properly and the VDC
warning light
may illuminate.
•The VDC system is not a substitute for win-
ter tires or tire chains on a snow covered
road.
•If VDC is malfunctioning, VDC is unable to
stabilize the vehicle. In addition, other driv-
ing safety systems are switched off. This
increases the risk of skidding and an acci-
dent. Drive on carefully. Have VDC checked.
It is recommended you visit an INFINITI re-
tailer for this service.
CAUTION
•When VDC is deactivated, theVDC
OFF warning light lights up continuously.
•If both thewarning light andwarning light are lit continuously, VDC is
not available due to a malfunction.
TRACTION CONTROL SYSTEM (TCS)
The Traction Control System (TCS) is part of
VDC..
Traction control brakes the drive wheels indi-
vidually if they spin. This enables you to pull
away and accelerate on slippery surfaces, for
example if the road surface is slippery on one
side. In addition, more drive torque is trans-
ferred to the wheel or wheels with traction.
Traction control remains active if you deactivate
VDC.
CHARACTERISTICS OF VDC
If theVDC warning light goes out before
beginning the journey, VDC is automatically
active.
If VDC intervenes, the
VDC warning lamp
flashes in the combination meter.
If VDC intervenes:
•Do not deactivate VDC under any circum-
stances.
•When pulling away, only depress the accel-
erator pedal as far as is necessary.
•Adapt your driving style to suit the prevailing
road and weather conditions.
Deactivating/activating VDC
WARNING
If you deactivate VDC, VDC no longer stabilizes
the vehicle. There is an increased risk of skid-
ding and an accident.
Only deactivate VDC in the situations de-
scribed in the following section.
You can select between the following statuses
of VDC:
•VDC is activated.
•VDC is deactivated.
It may be best to deactivate VDC in the follow-
ing situations:
•When using snow chains.
•In deep snow.
•On sand or gravel.
NOTE
Activate VDC as soon as the situations described
above no longer apply. VDC will otherwise not be
Starting and driving5-91

able to stabilize the vehicle if the vehicle starts
to skid or a wheel starts to spin.
You can activate/deactivate VDC using the ve-
hicle information display. To activate/
deactivate VDC:
1. Start the engine
2. Press the
orbutton on the
steering wheel to select the [DriveAssist]
menu in the vehicle information display.
3. Press the
orbutton to select
VDC.
4. Press the button on the steering wheel.
The current selection is displayed.
5. To activate/deactivate: press the but-
ton again.
VDC is deactivated if the
warning light
in the combination meter lights up continu-
ously when the engine is running.
Characteristics when VDC is deactivated
:
If VDC is deactivated and one or more wheels
start to spin, theVDC warning lamp
flashes in the combination meter. In such situ-
ations, VDC will not stabilize the vehicle. If you deactivate VDC:
•VDC no longer intervenes in understeer or
oversteer situations.
•Engine torque is no longer limited and the
drive wheels are able to spin.
The spinning of the wheels results in a
cutting action, so the tires cut through the
loose surface until the hit solid ground,
giving better traction.
•Traction control is still activated.
•VDC still provides support when you brake.
EBD (ELECTRONIC BRAKE FORCE
DISTRIBUTION)
EBD monitors and controls the brake pressure
on the rear wheels to help improve handling
during braking.
WARNING
If EBD is malfunctioning, the EBD [Inoperative
See Operator’s Manual] warning is displayed
in the vehicle information display. The
VDC warning lamp may also light up.
If EBD is malfunctioning as a result of a VDC
malfunction, the rear wheels can lock, e.g. un-
der full braking. This increases the risk of skid-
ding and an accident.You should therefore adapt your driving style
to the different handling characteristics. Have
the brake system checked. It is recommended
you see an INFINITI retailer.
STEER CONTROL
STEER CONTROL helps you by transmitting a
noticeable steering force to the steering wheel
in the direction required for vehicle stabilisa-
tion.
This steering support is provided in particular if:
•Both right wheels or both left wheels are on
a wet or slippery road surface when you
brake.
•The vehicle starts to skid.
WARNING
No steering support is provided from STEER
CONTROL, if:
•VDC is malfunctioning.
•The steering is faulty.
Power steering will, however, continue to
function.
5-92Starting and driving

will flash for approximately 1 minute. The
light will remain on after 1 minute. It is rec-
ommended you Contact an INFINITI retailer
as soon as possible for tire replacement
and/or system resetting.
•Replacing tires with those not originally
specified by INFINITI could affect the proper
operation of the TPMS.
•If you used Emergency Tire Sealant to repair
a minor tire puncture, the TPMS sensor
should be checked when repairing or re-
placing the tire. It is recommended you visit
an INFINITI retailer for this service.
The Tire Pressure Monitoring System (TPMS)
monitors tire pressure of all tires. When the low
tire pressure warning light is lit, and a tire
pressure-related warning (if equipped) appears
in the vehicle information display, one or more
of your tires is significantly under-inflated. If
the vehicle is being driven with low tire pres-
sure, the TPMS will activate and warn you of it
by the low tire pressure warning light (in the
meter panel). This system will activate only
when the vehicle is driven at speeds above 16
MPH (25 km/h). For more details about the TPMS, see
Tire
Pressure Monitoring System (TPMS) in the
5. Starting and driving section.
STOPPING VEHICLE
WARNING
•Be sure to apply the parking brake firmly.
•Be sure that P (Park) is engaged.
•Never change tires when the vehicle is on a
slope, ice or slippery area. This is hazard-
ous.
•Never change tires when the oncoming traf-
fic is close to your vehicle. Call for profes-
sional road assistance.
1. Safely move the vehicle off the road away from traffic.
2. Turn on the hazard indicator flasher lights.
3. Park on a level surface.
4. Apply the parking brake.
5. Press the P (Park) button.
6. Turn off the engine. 7. Open the hood and set up the triangle
reflector (if equipped):
•To warn other traffic.
•To signal professional road assistance
personnel that you need assistance.
8. Have all passengers get out of the vehicle and stand in a safe place, away from other
traffic and clear of the vehicle.
In case of emergency6-3

WARNING
•Do not continue to drive if your vehicle over-
heats. Doing so could cause engine damage
or a vehicle fire.
•To avoid the danger of being scalded, never
remove the radiator or coolant reservoir cap
while the engine is hot. When the radiator or
coolant reservoir cap is removed, pressur-
ized hot water will spurt out, possibly caus-
ing serious injury.
•Do not open the hood if steam is coming out.
If the engine of your vehicle is overheating
(indicated by the engine coolant temperature
gauge) or if you feel a lack of engine power,
detect unusual noise, etc., proceed as follows:
1. Move and park the vehicle safely off the road and away from traffic.
2. Turn on the hazard warning flasher lights.
3. Apply the parking brake.
4. Press the P (Park) button. DO NOT STOP THE ENGINE.
5. Open all windows. 6. Switch off the air conditioner system (if
equipped).
7. Set the heater or air conditioner temperature control to maximum “HOT” and fan speed
control to maximum speed.
8. Exit the vehicle.
9. Visually inspect and listen for steam or coolant escaping from the radiator before
opening the hood.WARNING
If steam or water is coming from the engine,
stand clear to prevent getting burned.
10. Open the hood. For details, see Hoodin
the 3. Pre-driving checks and adjustments
section.
11. Visually check if the cooling fan is running.
12. Visually check the radiator and radiator hoses for leakage.
WARNING
Be careful not to allow your hands, hair, jew-
elry or clothing to come into contact with, or
get caught in, engine belts or the engine cool-
ing fan. The engine cooling fan can start at any
time.
13. After the engine cools down, check the coolant level in the engine coolant reservoir
with the engine running. Do not open the
radiator cap (if equipped).
14. If the level is low, remove the engine cool- ant reservoir cap and add coolant slowly
into the reservoir. After refilling the reser-
voir to the MAX level, install the reservoir
cap.
15. Close the hood.
Have your vehicle inspected or repaired. It is
recommended you visit an INFINITI retailer.
IF YOUR VEHICLE OVERHEATS
In case of emergency6-13

8 Do-it-yourself
Maintenance precautions..................8-2
Engine compartment check locations ...........8-3
2.0L Gasoline engine .................. .8-3
Engine cooling system ................... .8-3
Checking engine coolant level .............8-4
Changing engine coolant ................8-4
Engine oil ........................... .8-5
Checking engine oil level ................8-5
Changing engine oil .................. .8-5
Changing engine oil filter ................8-6
Automatic Transmission Fluid (ATF) ............8-7
Brake fluid .......................... .8-7
Window washer fluid .................... .8-8
Battery ............................ .8-9
Accessing Vehicle battery ...............8-10
Maintenance free battery ................8-10
Models with Idle Stop/Start System .........8-10
Battery replacement .................. .8-11
Reinitialisation procedure after battery
reconnection ...................... .8-12
Jump-starting ...................... .8-12
Drive belt .......................... .8-12
Spark plugs ..........................8-13
Air cleaner filter ...................... .8-13
Wiper blades .........................8-13 Cleaning
..........................8-13
Replacing front window wiper blades ........8-14
Replacing rear window wiper blade ..........8-15
Brakes ............................ .8-17
Self-adjusting brakes ..................8-17
Fuses ............................. .8-17
Before replacing a fuse .................8-17
Engine compartment .................. .8-17
Passenger compartment ................8-18
Intelligent key battery replacement ..........
.8-20
Checking the

battery ..................8-20
Replacing the battery ..................8-20
Lights ............................ .8-22
Exterior and interior lights ...............8-22
Replacement procedures ................8-24
Wheels and tires ..................... .8-26
Tire Pressure ...................... .8-26
Tire inflation pressure .................8-28
Tire labeling ...................... .8-28
Types of tires ..................... .8-30
Tire chains ....................... .8-31
Tire wear and damage .................8-31
Tire rotation ...................... .8-32
Replacing wheels and tires ..............8-32
Wheel balance ..................... .8-34

5. Wipe the engine oil filter sealing surface witha clean rag.
CAUTION
•Be sure to remove any old gasket material
remaining on the sealing surface of the en-
gine. Failure to do so could lead to an oil
leak and engine damage.
•The dipstick must be inserted in place to
prevent oil spillage from the dipstick hole
when filling the engine with oil.
6. Coat the gasket on the new filter with clean engine oil.
7. Screw on the oil filter until a slight resis- tance is felt, then tighten an additional
2/3 turn. Engine oil filter tightening torque:
19 ft-lb, 25 N•m
8. Start the engine and check for leakage around the oil filter. Correct as required.
9. Turn the engine off and wait more than 10 minutes. Check the oil level. Add engine oil
if necessary. It is recommended that you visit an INFINITI
retailer if checking or replacement is required.
CAUTION
•Use only Shell DCT-M1 or equivalent. Do not
mix with other fluids.
•Using automatic transmission fluid other
than Shell DCT-M1 may cause deterioration
in driveability and automatic transmission
durability, and may damage the automatic
transmission. Damage caused by the use of
fluids other than as recommended is not
covered by the warranty.
WARNING
•Use only new fluid. Old, inferior, or contami-
nated fluid may damage the brake systems.
The use of improper fluids can damage the
brake system and affect the vehicle’s stop-
ping ability.
•Clean the filler cap before removing.
•Brake fluid is poisonous and should be
stored carefully in marked containers out of
the reach of children.
CAUTION
•Do not spill the fluid on painted surfaces.
This will damage the paint. If fluid is spilled,
wash with water.
NDI1599
AUTOMATIC TRANSMISSION FLUID (ATF) BRAKE FLUID
Do-it-yourself8-7

Check the fluid level in the reservoir. If the
brake fluid is below the MIN line
2, the brake
warning light will illuminate. Add brake fluid up
to the MAX line
1. For additional information
on the recommended type of brake fluid, refer
Recommended fluids/lubricants and
capacities in the9. Maintenance and Sched-
ules section.
If the brake fluid must be added frequently, the
brake system should be thoroughly checked. It
is recommended that you visit an INFINITI re-
tailer for this service. Fill the windshield-washer fluid reservoir peri-
odically. Add fluid when the low washer fluid
warning appears on the vehicle information
display.
To fill the windshield-washer fluid reservoir, lift
the cap off the reservoir and pour the
windshield-washer fluid into the reservoir open-
ing.
Add a washer solvent to the washer for better
cleaning. In the winter season, add a
windshield-washer antifreeze. Follow the manu-
facturer’s instructions for the mixture ratio.
Refill the reservoir more frequently when driv-
ing conditions require an increased amount of
windshield-washer fluid.
Recommended fluid is Genuine INFINITI Wind-
shield Washer Concentrate Cleaner & Antifreeze
or equivalent.
CAUTION
•Do not substitute engine antifreeze coolant
for window washer solution. This may result
in damage to the paint.
•Do not fill the window washer reservoir tank
with washer fluid concentrates at full
strength. Some methyl alcohol based
washer fluid concentrates may permanently
stain the grille if spilled while filling the
window washer reservoir tank.
•Pre-mix washer fluid concentrates with wa-
ter to the manufacturer’s recommended lev-
els before pouring the fluid into the window
washer reservoir tank. Do not use the win-
dow washer reservoir tank to mix the
washer fluid concentrate and water.
NDI1601
WINDOW WASHER FLUID
8-8Do-it-yourself