charging INFINITI QX30 2017 Owner's Manual

MessagePossible causes/consequences and solutions
[Parking Brake Inoperative]The yellowwarning light is lit. The redindicator light flashes for about ten seconds after the electric parking brake has been
applied or released. It then goes out or remains lit.
The electric parking brake is malfunctioning, e.g. because of overvoltage or undervoltage.
1. Rectify the cause of the overvoltage or undervoltage, e.g. by charging the battery or restarting the engine.
2. Apply or release the electric parking brake.
If the electric parking brake still cannot be applied or released:
1. Switch the ignition off and turn it back on.
2. Apply or release the electric parking brake manually.
If the electric parking brake still cannot be applied or released, it is recommended you consult an INFINITI retailer.
The yellow
warning light is lit. The redindicator light flashes.
It is not possible to apply the electric parking brake manually.
1. Press the P (Park) button.
Consult an INFINITI retailer.
[Brake Immediately] A tone may also sound at regular intervals. If you attempt to lock the vehicle, the tone becomes louder.
You cannot start the engine.
1. Paying attention to the traffic situation, immediately depress the brake pedal firmly and hold until the display message disappears.
2. Secure the vehicle against rolling away. You can restart the engine.
Instruments and controls2-35

button turns off. Airflow and air distribution
are set to automatic mode.
or
•Air-conditioning system or automatic climate
control: adjust the temperature control (see
Heater and air conditionerin the4. Display
screen, heater and air conditioner, and audio
system section).
HEADLIGHT SWITCH
1Left-hand parking lights
2Right-hand parking lights
3Side lights and license plate light-
ing
4 Automatic headlight mode, con-
trolled by the light sensor
5Low beam/high beam headlights
6Rear fog light
7Front fog lights (if equipped)
8Headlight aiming control (halogen head-
lights only)
INFINITI recommends that you consult the local
regulations concerning the use of lights. If you hear a warning tone when you leave the
vehicle, the side lights may still be switched on.
Turn the light switch to
.
The exterior lighting (except the side lights/
parking lights) switches off automatically if you:
•Remove the key from the ignition switch (if
equipped).
•Open the driver’s door with the ignition
switch in the OFF position.
CAUTION
Use the headlights with the engine running to
avoid discharging the vehicle battery.
NIC2619LED headlightsNIC2697Halogen headlights
HEADLIGHT AND TURN SIGNAL SWITCHES
Instruments and controls2-63

Luggage compartment
The power outlet is used for powering electrical
accessories such as a cellular telephone.
An emergency cut-off ensures that the on-board
voltage does not drop too low. If the on board
voltage is too low, the power to the sockets is
automatically cut. This ensures that there is
sufficient power to start the engine.
CAUTION
•The outlet and plug may be hot during or
immediately after use.
•Only certain power outlets are designed for
use with a cigarette lighter unit. Do not use
any other power outlet for an accessory
lighter. It is recommended you visit an
INFINITI retailer for additional information.
•Do not use with accessories that exceed a 12
volt, 180W (15A) power draw. Do not use
double adapters or more than one electrical
accessory.
•Use this power outlet with the engine run-
ning to avoid discharging the vehicle bat-
tery.
•Avoid using when the air conditioner, head-
lights or rear window defogger is on.
•Push the plug in as far as it will go. If good
contact is not made, the plug may overheat
or the internal temperature fuse may blow.
•Before inserting or disconnecting a plug, be
sure that the electrical accessory being
used is turned OFF.
•When not in use, be sure to close the cap. Do
not allow water to contact the outlet.
WARNING
Keep the storage lids closed while driving to
help prevent injury in an accident or a sudden
stop.
NIC2684
STORAGE
Instruments and controls2-77

If you activate air-recirculation mode, the win-
dows can mist up more quickly, in particular at
low temperatures. Only use air recirculation
mode briefly to prevent the windows misting
up.
Activating air recirculation mode
:
Make sure the ignition switch is in the ON
position.
Press the
button. The indicator light in
thebutton lights up.
Air-recirculation mode is activated automati-
cally at high outside temperatures or high
levels of pollution. When air-recirculation mode
is activated automatically, the indicator light in
the
button is not lit. Outside air is added
after about 30 minutes.
Deactivating air recirculation mode
:
Press thebutton. The indicator light in
thebutton goes out.
NOTE
Air-recirculation mode is deactivated automati-
cally:
•After approximately five minutes at outside
temperatures below approximately 45oF
(7oC).
•After approximately five minutes if the Cool-
ing with air dehumidification function is
deactivated.
•After approximately 30 minutes at outside
temperatures above approximately 45oF
(7oC) if the cooling with air dehumidification
function is activated.
SERVICING AIR CONDITIONER
WARNING
The air conditioner system contains refriger-
ant under high pressure. To avoid personal in-
jury, any air conditioner service should be
done only by an experienced technician with
the proper equipment.
The air conditioner system in your vehicle is
charged with a refrigerant designed with the
environment in mind.
This refrigerant will not harm the earth’s ozone
layer.
Special charging equipment and lubricant are
required when servicing your vehicle’s air con-
ditioner. Using improper refrigerants or lubri-
cants will cause severe damage to the air
conditioner system. (See Air conditioner sys-tem refrigerant and oil recommendations
in the
9. Maintenance and Schedules section.)
An INFINITI retailer will be able to service your
environmentally friendly air conditioner system.
Air conditioner filter
The air conditioner system is equipped with an
air conditioner filter. To make sure the air
conditioner heats, defogs, and ventilates effi-
ciently, replace the filter in accordance with the
specified maintenance intervals listed in the
separate maintenance booklet. It is recom-
mended you visit an INFINITI retailer for this
service.
The filter should be replaced if the air flow
decreases significantly or if windows fog up
easily when operating the heater or air condi-
tioner.
Display screen, heater and air conditioner, and audio system4-51

IPOD PLAYER
Connecting iPod
WARNING
Do not connect, disconnect or operate the iPod
while driving. Doing so can be a distraction. If
distracted you could lose control of your ve-
hicle and cause an accident or serious injury.
CAUTION
•Do not force the iPod device into the USB
port. Inserting the iPod cable tilted or up-
side down into the port may damage the
port. Make sure that the iPod cable is con-
nected correctly to the USB port.
•Do not grab the USB port cover (if equipped)
when pulling the iPod cable out of the port.
This could damage the port and the cover.
•Do not leave the iPod cable in a place where
it can be pulled unintentionally. Pulling the
cable may damage the port.
Refer to your device manufacturer’s owner in-
formation regarding the proper use and care of
the device. Two USB (iPod) connectors are located on the
center console box.
USB (Universal Serial Bus) connection port/
iPod page 4-56
The battery of the iPod will be charged while the
device is connected to the vehicle if the iPod
supports USB connection charging.
Depending on the model and firmware version
of the iPod, the display on the iPod shows an
INFINITI or Accessory Attached screen when the
connection is completed. When the iPod is
connected to the vehicle, the iPod music library
can only be operated using the vehicle audio
controls.
Compatibility
:
Made for
•iPod touchR(5th generation)
•iPod touchR(4th generation)
•iPod touchR(3rd generation)
•iPod touchR(2nd generation)
•iPod touchR(1st generation)
•iPod touchR
•iPodRwith video
•iPod classicR
•iPod nanoR(7th generation)
•iPod nanoR(6th generation)
•iPod nanoR(5th generation)
•iPod nanoR(4th generation)
•iPod nanoR(3rd generation)
•iPod nanoR(2nd generation)
•iPod nanoR(1st generation)
•iPhoneR6 Plus
•iPhoneR6
•iPhoneR5S
•iPhoneR5
•iPhoneR4S
•iPhoneR4
•iPhoneR3GS
•iPhoneR3G
•iPhoneR
The iPod touchRmay not respond quickly with
the system in some cases.
Make sure that the iPod
Rfirmware is up-
dated.
The Lightning
TMconnector works with
iPhone
R5, iPhoneR5S, iPhoneR6,
4-74Display screen, heater and air conditioner, and audio system

•Some Bluetooth® enabled cellular phones
may not be recognized by the in-vehicle
phone module. Please visit
www.infinitiusa.com/bluetooth and search
for a recommended phone list.
•You will not be able to use a hands-free
phone under the following conditions:– Your vehicle is outside the service area for your cellular phone network.
– Your vehicle is in an area where it is difficult to receive radio waves, such as in
a tunnel, in an underground parking ga-
rage, behind a tall building or in a moun-
tainous area.
– Your cellular phone is locked in order to prevent dialing.
•When the radio wave condition is not ideal or
ambient sound is too loud, it may be difficult
to hear the other person’s voice during a call.
•This Bluetooth® system supports Wideband
speech, which enhances the sound quality of
phone calls placed over Bluetooth®. To take
advantage of this feature, the cellular device
should be used on a carrier supporting Adap-
tive Multi-Rate Wideband (AMR-WB) or HD
voice technology. The performance of
AMR-WB may vary by carrier and calling area.
Consult your cellular carrier if you experience
issues with call quality or connection.
•Immediately after the ignition switch is
turned ON, it may be impossible to receive a
call for a short period of time.
•Do not place the cellular phone in an area
surrounded by metal or far away from the
in-vehicle phone module to prevent tone
quality degradation and wireless connection
disruption.
•While a cellular phone is connected through
the Bluetooth® wireless connection, the bat-
tery of the cellular phone may discharge
quicker than usual.
•If the Bluetooth® Hands-Free Phone System
seems to be malfunctioning, please visit
www.infinitiusa.com/bluetooth for trouble-
shooting help.
•Some cellular phones or other devices may
cause interference or a buzzing noise to be
emitted from the audio system speakers.
Storing the device in a different location may
reduce or eliminate the noise.
•Refer to the owner’s manual for the cellular
phone for information regarding the tele-
phone pairing procedure specific to your
phone, battery charging, and cellular phone
antenna, etc.
•The antenna display on the monitor may not
match the antenna display of some cellular
phones.
•The battery display on the monitor may not
match the battery display of some cellular
phones.
•Keep the interior of the vehicle as quiet as
possible to hear the caller’s voice clearly as
well as to minimize echoes.
•If reception between callers is unclear, ad-
justing the incoming or outgoing call volume
may improve the clarity.
REGULATORY INFORMATION
FCC Regulatory Information
FCC ID : HYQDNNS075
NOTE: This device complies with part 15 of the
FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including in-
terference that may cause undesired operation.
FCC WARNING: Changes or modifications not
expressly approved by the party responsible for
compliance could void the user’s authority to
operate the equipment.
4-84Display screen, heater and air conditioner, and audio system

iPod player
SymptomPossible cause Possible solution
The system does not recognize an iPod. The connector cable is not correctly connected or the iPod does not correctly operate.Connect the connector cable again. If the system
does not recognize the iPod after performing the procedure above, reset the iPod.
The iPod that is to be connected is not compatible with the system. Check the iPod model and firmware versions
available for the system.
The USB extension cable is not correctly connected. Do not use a USB extension cable.
The cable is rapidly connected to or disconnected from the USB connector. Slowly connect or disconnect the USB cable.
An iPod cannot be operated. The iPod is connected to the in-vehicle audio system
while headsets, etc. are connected to the iPod. Remove all equipment from the iPod after
disconnecting the iPod from the system, and then connect it to the system again.
The iPod is not operating normally. Disconnect and re-connect the iPod to the in-vehicle
audio system.
The system plays back an album/track that includes particular album art. Disconnect the iPod from the in-vehicle audio system
and then reset the iPod. Disable the album art and then re-connect the iPod to the system.
An iPod does not respond. There are too many tracks in a category. Decrease the number of tracks in a category (less
than 3,000 tracks).
The shuffle function is turned on. Turn off the shuffle function if many tracks are stored
on the iPod.
Music cannot be played back. The connector is not connected to the iPod. Firmly connect the connector until it clicks.
Music stops playing. The sound cuts off due to vibration resulting from the
iPod being in an unstable location. Place the iPod in a stable location where it does not
roll over.
The sound is distorted. The EQ (equalizer) function of the iPod is turned on. Turn off the EQ (equalizer) function.
The iPod battery requires more time than usual to charge. Charging the iPod battery may take longer while the
iPod is playing. If the iPod requires charging, it is recommended to
stop playback
4-128Display screen, heater and air conditioner, and audio system

0OFF position
1ACC position
2ON position
3START position
WARNING
Never remove the key or turn the ignition
switch to the OFF position while driving. The
steering wheel will lock and could cause the
driver to lose control of the vehicle. This could
result in serious vehicle damage or personal
injury.
CAUTION
Use electrical accessories with the engine run-
ning to avoid discharging the vehicle battery.
If you must use accessories while the engine is
not running, do not use them for extended pe-
riods of time and do not use multiple electrical
accessories at the same time.
The switch includes an anti-theft steering lock
device.
STEERING LOCK
To lock the steering wheel
1. Turn the key to the OFF position.
2. Remove the key from the ignition switch.
3. Turn the steering wheel 1/6 of a turn clock- wise from the straight up position.
To unlock the steering wheel
1. Insert the key into the ignition switch.
2. Gently turn the key while rotating the steer- ing wheel slightly right and left.
KEY POSITIONS
OFF (Normal parking position)
0
The ignition key can only be removed when in
this position.
The steering lock can only be locked in this
position.
ACC (Accessories)/1
The engine is turned off without locking the
steering wheel. This position activates electrical
accessories, such as the radio, when the engine
is not running.
ON (Normal operating position)2
This position turns on the ignition system and
electrical accessories.
START3
The engine starter activates and the engine will
start. As soon as the engine has started, release
the key immediately. It will return to the ON
position.
NPA1483
IGNITION SWITCH
Starting and driving5-15

SWITCHING OFF THE ENGINE
WARNING
The automatic transmission switches to posi-
tion N (Neutral) when you switch off the en-
gine. The vehicle may roll away. There is a risk
of an accident.
After switching off the engine, always switch
to position P (Park). Prevent the parked vehicle
from rolling away by applying the parking
brake.
Procedure
1. Apply the electric parking brake.
2. Shift the transmission to position P (Park).
3.With the key: turn the key to the position OFF
in the ignition switch and remove it The
immobilizer is activated.
If you switch the engine off with the transmis-
sion in position R (Reverse) or D (Drive), the
automatic transmission shifts to N (Neutral)
automatically.
With the key: if you then open the driver’s door
or the front-passenger door or remove the key
from the ignition, the automatic transmission
shifts to P (Park) automatically. If you want the automatic transmission to re-
main in neutral N (Neutral), e.g. when having
the vehicle cleaned in an automatic car wash
with a towing system:
With the key
:
1. Switch the ignition on.
2. Depress the brake pedal and keep it de-
pressed.
3. Shift to N (Neutral).
4. Release the brake pedal.
5. Release the electric parking brake.
6. Switch off the ignition and leave the key in the ignition switch.
EXTENDED PARKING
If you leave the vehicle parked up for longer
than four weeks, the battery may be damaged
by exhaustive discharging.
If you leave the vehicle parked up for longer
than six weeks, it may suffer from lack of use.
Visit an INFINITI retailer and seek advice
NOTE
You can obtain information about trickle char-
gers from an INFINITI retailer. The electric power steering system is designed
to reduce the driver effort required to steer the
vehicle.
WARNING
If during operation a fault is detected the fol-
lowing message will be displayed in the ve-
hicle information display along with an audible
warning tone.
[Power Steering Malfunction See Operators
Manual]
In conjunction with this warning, steering as-
sistance will no longer be provided by the sys-
tem.
The effort required to steer the vehicle will
increase. This will be most noticeable at low
speed and when performing a tight turning
maneuver.
Check whether you are able to provide the ex-
tra effort required.
If you are able to steer safely: Carefully drive on
to an INFINITI retailer.
If you are unable to steer safely: Do NOT drive
on. It is recommended you contact the nearest
INFINITI retailer for assistance.
ELECTRIC POWER STEERING SYSTEM
5-86Starting and driving

WARNING
Always follow the instructions below. Failure
to do so could result in damage to the charging
system and cause personal injury.1. If the booster battery is in another vehicle,
position the two vehicles to bring their bat-
teries near each other.
Do not allow the two vehicles to touch. 2. Check if the parking brake is applied.
If not, after connecting the vehicle with the
booster battery (after step 8), apply the
parking brake.
The vehicle has an electric parking brake, for
more information see, Parking brakein the
3. Pre-driving checks and adjustments sec-
tion
3. Press the P (Park) button.
4. Switch off all unnecessary electrical systems (headlights, hazard lights etc,).
5. Ensure that the ignition switch of the vehicle being jump-started is in the OFF position.
6. Open the hood. For details, see Hoodin the
3. Pre-driving checks and adjustments sec-
tion.
7. Remove the vent caps (if equipped) on the battery and cover the battery with an old
cloth.
8. Connect the jump leads in the sequence (
1→2→3→4) as illustrated.NDI1595
In case of emergency6-11