trip computer INFINITI QX30 2017 Owner's Manual

MENUS AND SUBMENUS
To call up the menu bar4and select a menu,
press theorbutton on the steering
wheel. Menu bar
4disappears after a few
seconds.
Depending on the equipment fitted in the ve-
hicle, you can call up the following menus:
•[Trip] menu
•[Navi] menu (navigation instructions)
•[Audio] menu
•[DriveAssist] menu
•[Serv.] menu
•[Settings] menu
The [Audio] and [Navi] menus differ slightly in
vehicles with an audio system and in vehicles
with a navigation system. The examples given
in this Owner’s Manual apply to vehicles
equipped with navigation.
[Trip] menu
Standard display:
Press and hold thebutton on the steering
wheel until the [Trip] menu with trip meter
1and total distance recorder2is shown. Trip computer [From start] or [From reset]
:
1Distance
2Driving time
3Average speed
4Average fuel consumption
Press the
orbutton on the steering
wheel to select the [Trip] menu.
Press the
orbutton to select [From
start] or [From reset].
The values in the [From start] submenu are
calculated from the start of a journey whilst the
values in the [From reset] submenu are calcu-
lated from the last time the submenu was reset.
NIC2753NIC2711
2-16Instruments and controls

The [From start] trip computer is automatically
reset when:
•The ignition has been switched off for more
than four hours.
•999 hours have been exceeded.
•9999 kilometers have been exceeded.
The [From reset] trip computer is automatically
reset if the value exceeds 9999 hours or 99999
kilometers. Displaying the range and current fuel consump-
tion
:
Press theorbutton on the steering
wheel to select the [Trip] menu.
Press the
orbutton to select
approximate range
1and current fuel con-
sumption
2.
Approximate range
1that can be covered is
calculated according to your current driving
style and the amount of fuel in the tank. If there
is only a small amount of fuel left in the fuel
tank, the display shows a vehicle being refu-
elled instead of approximate range
1. Digital speedometer
:
Press theorbutton on the steering
wheel to select the [Trip] menu.
Press the
orbutton to select digital
speedometer
2.
A gearshift recommendation
1can also be
displayed.
Observe the information on gearshift recom-
mendation
1for automatic transmission (shift-
ing manually) (see Driving with Automatic
Transmission in the5. Starting and driving
section).
NIC2713NIC2714
Instruments and controls2-17

Resetting values:
Press theorbutton on the steering
wheel to select the [Trip] menu.
Press the
orbutton to select the
function that you wish to reset.
Press the button.
Select
[Yes] and press to confirm.
You can reset the values of the following func-
tions:
•Trip meter
•[From start] trip computer
•[From reset] trip computer
Navigation menu ([Navi])
Displaying navigation instructions:
In the [Navi] menu, the vehicle information
display shows navigation instructions.
You can find further information on navigation
in the audio system or navigation system oper-
ating instructions.
Switch on the audio system or navigation sys-
tem.
Press the
orbutton on the steering
wheel to select the [Navi] menu. Route guidance not active:
1Direction of travel
2Current road
NIC2718NIC2719
2-18Instruments and controls

1. Press theorbutton on the
steering wheel to select the [Settings] menu.
2. Press the
orbutton to select
[Instrument Cluster] submenu.
3. Press to confirm.
4. Press the
orbutton to select
the [Display Unit Speed-/Odometer] func-
tion.
You will see the selected setting: [miles] or
[km].
5. Press the button to change the setting.
The selected unit of measurement for distance
applies to:
•Digital speedometer in the [Trip] menu.
•Total distance recorder and the trip meter.
•Trip computer.
•Current fuel consumption and approximate
range.
•Navigation instructions in the [Navi] menu.
•Cruise control.
•Speed limiter.
•Intelligent cruise control (ICC).
•Maintenance service interval display. Switching the additional speedometer on/off.
The [Speedometer (mph)] or [Speedometer (km/
h)] function allows you to choose whether the
vehicle information display in the status area
shows the speed in MPH or in km/h instead of
the outside temperature.
1. Press the
orbutton on the
steering wheel to select the [Settings] menu.
2. Press the
orbutton to select
[Instrument Cluster] submenu.
3. Press to confirm.
4. Press the
orbutton to select
the [Speedometer (mph)] or [Speedometer
(km/h)] function.
You will see the selected setting: [On] or
[off].
5. Press the button to change the setting.
Selecting the permanent display function.
You can determine whether the vehicle informa-
tion display permanently shows the outside
temperature or the speed in MPH.
1. Press the
orbutton on the
steering wheel to select the [Settings] menu.
2. Press the
orbutton to select
[Instrument Cluster] submenu. 3. Press to confirm.
4. Press the
orbutton to select
the [Outside Temperature] function.
You will see the selected setting: [outside
temperature] or [Speedometer (mph)].
5. Press the button to save the setting.
Lights
Switching the Adaptive Front Lighting System
on/off:
1. Press theorbutton on the
steering wheel to select the [Settings] menu.
2. Press the
orbutton to select
[Light] submenu.
3. Press to confirm.
4. Press the
orbutton to select
the [Adaptive front lighting system] function.
If the [Adaptive front lighting system] func-
tion has been switched on, the cone of light
and the
symbol in the vehicle infor-
mation display are shown in orange.
5. Press the button to save the setting.
Instruments and controls2-25