radio INFINITI QX30 2017 User Guide

The Intelligent Key system can operate all the
door locks using the remote control function or
touching the request switch on the vehicle
without taking the key out from a pocket or
purse. The operating environment and/or con-
ditions may affect the Intelligent Key system
operation.
Be sure to read the following before using the
Intelligent Key system.
CAUTION
•Be sure to carry the Intelligent Key with you
when operating the vehicle.
•Never leave the Intelligent Key in the ve-
hicle when you leave the vehicle.
The Intelligent Key is always communicating
with the vehicle as it receives radio waves. The
Intelligent Key system transmits weak radio
waves. Environmental conditions may interfere
with the operation of the Intelligent Key system
under the following operating conditions:
•When operating near a location where
strong radio waves are transmitted, such as
a TV tower, power station and broadcasting
station.
•When in possession of wireless equipment,
such as a cellular telephone, transceiver or a
CB radio.
•When the Intelligent Key is in contact with or
covered by metallic materials.
•When any type of radio wave remote control
is used nearby.
•When the Intelligent Key is placed near an
electric appliance such as a personal com-
puter.
•When the vehicle is parked near a parking
meter.
In such cases, correct the operating conditions
before using the Intelligent Key function or use
the mechanical key.
Although the life of the battery varies depend-
ing on the operating conditions, the battery’s
life is approximately two years. If the battery is
discharged, replace it with a new one.
When the Intelligent Key battery is low, an
indicator illuminates in the vehicle information
display. For additional information, refer to
Safety systemsin the2. Instruments and
controlssection.Since the Intelligent Key is continuously receiv-
ing radio waves, if the key is left near equip-
ment which transmits strong radio waves, such
as signals from a TV and personal computer, the
battery life may become shorter.
For additional information, refer toIntelligent
key battery replacementin the
8. Do-it-yourselfsection.
As many as four Intelligent Keys can be regis-
tered and used with one vehicle. For informa-
tion about the purchase and use of additional
Intelligent Keys, it is recommended that you
visit an INFINITI retailer.
CAUTION
Listed below are conditions or occurrences
which will damage the Intelligent Key:
•Do not allow the Intelligent Key, which con-
tains electrical components, to come into
contact with water or salt water. This could
affect the system function.
•Do not drop the Intelligent Key.
•Do not strike the Intelligent Key sharply
against another object.
•Do not change or modify the Intelligent Key.
3-8Pre-driving checks and adjustments

•Wetting may damage the Intelligent Key. If
the Intelligent Key gets wet, immediately
wipe until it is completely dry.
•Do not place the Intelligent Key for an ex-
tended period in an area where tempera-
tures exceed 140
oF (60oC).
•Do not attach the Intelligent Key with a key
holder that contains a magnet.
•Do not place the Intelligent Key near equip-
ment that produces a magnetic field, such
as a TV, audio equipment and personal
computers.
If an Intelligent Key is lost or stolen, INFINITI
recommends erasing the ID code of that Intelli-
gent Key from the vehicle. This may prevent the
unauthorized use of the Intelligent Key to oper-
ate the vehicle. For information regarding the
erasing procedure, it is recommended that you
visit an INFINITI retailer.
OPERATING RANGE
The Intelligent Key functions can only be used
when the Intelligent Key is within the specified
operating range from the request switch
1.When the Intelligent Key battery is discharged
or strong radio waves are present near the
operating location, the Intelligent Key operating
range becomes narrower, and the Intelligent
Key may not function properly.
The operating range is within 31.5 in (80 cm)
from each request switch
1.
If the Intelligent Key is too close to the door
glass, handle or rear bumper, the request
switches may not function.
When the Intelligent Key is within the operating
range, it is possible for anyone, even someone
who does not carry the Intelligent Key, to push
the request switch to lock/unlock the doors.
NPA1498
Pre-driving checks and adjustments3-9

TROUBLESHOOTING GUIDE
Verify the location of all Intelligent Keys that are programmed for the vehicle. If another Intelligent Key is in range or inside the vehicle, the vehicle
system may respond differently than expected.
Symptom Possible causeRemedy
You cannot
lock or un-
lock the ve-
hicle using
the keyThe key battery
is discharged or
nearly dis-
charged:
•Vehicles without Intelligent Key:try again to lock/unlock the vehicle using the remote control function of the key. Point the tip of
the key at the driver’s door handle from close range and press the/button.
If this does not work:
•Check the key battery (seeChecking the batteryin the8. Do-it-yourselfsection) and replace it necessary
•Unlock (seeLocking with the mechanical keylater in this section) or lock the vehicle using the emergency key element
There is inter-
ference from a
powerful source
of radio waves
•Vehicles without Intelligent Key: try again to lock/unlock the vehicle using the remote control function of the key. Point the tip of
the key at the driver’s door handle from close range and press the/button.
If this does not work:
•Unlock (seeLocking with the mechanical keylater in this section) or lock the vehicle using the emergency key element
The key is faulty
•Unlock (seeLocking with the mechanical keylater in this section) or lock the vehicle using the emergency key element
•Have the key checked. It is recommended you visit an INFINITI retailer for this service.
You can no
longer lock or
unlock the
vehicle using
Intelligent
KeyThe key battery
is discharged or
nearly dis-
charged
•Check the key battery (seeChecking the batteryin the8. Do-it-yourselfsection) and replace it necessary
If this does not work:
•Unlock (seeLocking with the mechanical keylater in this section) or lock the vehicle using the emergency key element
There is inter-
ference from a
powerful source
of radio waves
•Unlock (seeLocking with the mechanical keylater in this section) or lock the vehicle using the emergency key element
There is a fault
with the Intelli-
gent Key system
•Lock/unlock the vehicle using the remote control function of the key.•Have the vehicle and key checked. It is recommended you visist an INFINITI retailer for this service.
If the vehicle can also not be locked/unlocked using the remote control function
•Unlock (seeLocking with the mechanical keylater in this section) or lock the vehicle using the emergency key element
•Have the vehicle and key checked. It is recommended you visit an INFINITI retailer for this service.
3-12Pre-driving checks and adjustments

Audio system(if equipped)................4-53
Audio operation precautions..............4-53
Names and functions of audio control buttons . .4-64
Main audio operation..................4-65
Radio...........................4-67
Compact Disc (CD) player................4-71
USB (Universal Serial Bus) connection port.....4-73
iPod player........................4-75
Bluetooth® streaming audio.............4-78
Audio settings......................4-82
Disc/USB memory device care and cleaning. . . .4-84
USB memory device...................4-84
Gracenote® End User License Agreement......4-85
Bluetooth® Hands-Free Phone System.........4-86
Regulatory information.................4-87
Phone...........................4-88
Connecting Bluetooth® device............4-91
Hands-free text messaging assistant........4-92
Phone and text message settings..........4-94
Bluetooth® information................4-98
INFINITI InTouch Apps overview..............4-99
Using Applications...................4-100
Vehicle Apps......................4-100Vehicle Apps Manager (if equipped)........4-102
Major Apps available for use in this system . . .4-103
Examples of how Vehicle Apps is used......4-104
Mobile Apps.......................4-104
Getting user ID and password............4-104
Notes on linking smartphone App to vehicle . . .4-105
Using smartphone applications...........4-105
INFINITI Voice Recognition system............4-105
Using Voice Recognition system...........4-105
Before starting.....................4-105
Giving voice commands................4-106
Voice recognition settings...............4-116
Information menu......................4-117
SiriusXM Travel Link®...............4-118
Settings menu.....................4-122
Troubleshooting guide...................4-124
Customer assistance..................4-124
System unit.......................4-125
Audio system......................4-126
Bluetooth® Hands-Free Phone System.......4-134
Monitor system.....................4-137
Voice recognition....................4-138

•The RearView Monitor is a convenience fea-
ture but it is not a substitute for proper
backing up. Always turn and look out the
windows, and check mirrors to be sure that
it is safe to move before operating the ve-
hicle. Always back up slowly.
•The system is designed as an aid to the
driver in showing large stationary objects
directly behind the vehicle, to help avoid
damaging the vehicle.
•The distance guide line and the vehicle
width line should be used as a reference
only when the vehicle is on a level paved
surface. The distance viewed on the monitor
is for reference only and may be different
than the actual distance between the ve-
hicle and displayed objects.
CAUTION
Do not scratch the camera lens when cleaning
dirt or snow from the lens.
The RearView Monitor system automatically
shows a rear view of the vehicle when the shift
lever is placed in the R (Reverse) position.
The radio can still be heard while the RearView
Monitor is active.To display the rear view, the RearView Monitor
system uses a camera located just above the
vehicle’s rear license plate
1.
REARVIEW MONITOR SYSTEM
OPERATION
With the ignition switch in the ON position,
move the shift lever to the R (Reverse) position
to operate the RearView Monitor.
HOW TO READ THE DISPLAYED LINES
Guiding lines which indicate the vehicle width
and distances to objects with reference to the
bumper line
Aare displayed on the monitor.
Distance guide lines:
Indicate distances from the bumper.
•Red line1: approx. 1.5 ft (0.5 m)
•Yellow line2: approx. 3 ft (1 m)
•Green line3: approx. 7 ft (2 m)
•Green line4: approx. 10 ft (3 m)
Vehicle width guide lines
5:
Indicate the approximate vehicle width when
backing up.
NAA1642SAA1896Z
4-18Display screen, heater and air conditioner, and audio system

AUDIO OPERATION PRECAUTIONS
WARNING
•The driver must not attempt to operate the
audio system while the vehicle is in motion,
so that full attention may be given to vehicle
operation.
•Park the vehicle in a safe location and apply
the parking brake before operating the au-
dio system and playing movies (if
equipped).
CAUTION
•Operate the audio system only when the
vehicle engine is running. Operating the au-
dio system for extended periods of time
with the engine turned off can discharge the
vehicle battery.
•Do not allow the system to get wet. Exces-
sive moisture such as spilled liquids may
cause the system to malfunction.
Radio
Turn the ignition switch to the ACC or ON
position before turning on the radio. If you
listen to the radio when the engine is not
running, the ignition switch should be pushed
to the ACC position.
Radio reception is affected by station signal
strength, distance from radio transmitter, build-
ings, bridges, mountains and other external
influences. Intermittent changes in reception
quality are normally caused by these external
influences.
Using a cellular phone in or near the vehicle may
influence radio reception quality.
Radio reception
Your radio system is equipped with state-of-the-
art electronic circuits to enhance radio recep-
tion. These circuits are designed to extend
reception range, and to enhance the quality of
that reception.
However there are some general characteristics
of both FM and AM radio signals that can affect
radio reception quality in a moving vehicle,
even when the best quality equipment is used.
These characteristics are completely normal in
a given reception area, and do not indicate any
malfunction in your radio system.
Reception conditions will constantly change
because of vehicle movement. Buildings, ter-
rain, signal distance and interference from
other vehicles can adversely affect ideal recep-
tion. Described below are some of the factors
that can affect radio reception.
Some cellular phones or other devices may
cause interference or a buzzing noise to come
from the audio system speakers. Storing the
device in a different location may reduce or
eliminate the noise.
AUDIO SYSTEM (IF EQUIPPED)
Display screen, heater and air conditioner, and audio system4-53

FM radio reception
MAXIMUM SIGNAL DISTANCES
•FM : 25 to 30 miles (40 to 48 km)
•AM : 60 to 130 miles (97 to 209 km)
Range: FM range is normally limited to 25 to 30
miles (40 to 48 km), with monaural (single
station) FM having slightly more range than
stereo FM. External influences may sometimes
interfere with FM station reception even if the
FM station is within 25 miles (40 km). The
strength of the FM signal is directly related to
the distance between the transmitter and re-
ceiver. FM signals follow a line-of-sight path,
exhibiting many of the same characteristics as
light. For example they will reflect off objects.
Fade and drift: As your vehicle moves away from
a station transmitter, the signals will tend to
fade and/or drift.Static and flutter: During signal interference
from buildings, large hills or due to antenna
position, usually in conjunction with an in-
creased distance from the station transmitter,
static or flutter can be heard. This can be
reduced by lowering the treble setting to reduce
the treble response.
Multipath reception: Because of the reflective
characteristics of FM signals, direct and re-
flected signals reach the receiver at the same
time. The signals may cancel each other, result-
ing in momentary flutter or loss of sound.
AM radio reception
AM signals, because of their low frequency, can
bend around objects and skip along the ground.
In addition, the signals can bounce off the
ionosphere and be bent back to earth. Because
of these characteristics, AM signals are also
subject to interference as they travel from trans-
mitter to receiver.
Fading: This occurs while the vehicle is passing
through freeway underpasses or in areas with
many tall buildings. It can also occur for several
seconds during ionospheric turbulence even in
areas where no obstacles exist.
Static: Caused by thunderstorms, electrical
power lines, electric signs and even traffic
lights.
HD RadioTMTechnology reception
(for U.S.)
HD RadioTMTechnology reception needs to be
activated to receive HD Radio broadcasts, see
Audio settingslater in this section.
This enables you to receive radio broadcasts
digitally (where available), providing a better
quality sound with clear reception. When this
feature is not activated or HD Radio broadcasts
are not available, you will receive analog radio
(AM/FM) broadcasts.
Satellite radio reception
When the satellite radio is used for the first time
or the battery has been replaced, the satellite
radio may not work properly. This is not a
malfunction. Wait more than 10 minutes with
the satellite radio ON and the vehicle outside of
any metal or large building for the satellite
radio to receive all of the necessary data.
The satellite radio requires an active SiriusXM
Satellite Radio subscription. The satellite ser-
vice is a available only to those at least 18 and
older in the 48 contiguous United States.
The satellite radio performance may be affected
if cargo carried on the roof blocks the satellite
radio signal.
SAA0306Z
4-54Display screen, heater and air conditioner, and audio system

If possible, do not put cargo near the satellite
antenna.
The build up of ice on the satellite radio an-
tenna can affect satellite radio performance.
Remove the ice to restore satellite radio recep-
tion.
Trademarks
HD Radio Technology manufactured under li-
cense from iBiuity Digital Corporation. U.S. and
Foreign Patents. HD Radio
TMand the HD, HD
Radio, and “Arc” logos are proprietary trade-
marks of iBiquity Digita; Corp.
The Bluetooth® word mark and logos are reg-
istered trademarks owned by Bluetooth SIG,
Inc. and any use of such marks by DENSO
CORPORATION is under license. Other trade-
marks and trade names are those of their
respective owners.
SiriusXM services require a subscription after
trial period and are sold separately or as a
package. Our satellite service is available only
to those at least 18 and older in the 48 contigu-
ous USA and DC. For more information visit
www.siriusxm.com.
Required SiriusXM Satellite Radio and SiriusXM
Travel Link monthly subscriptions are sold
separately. Sirius XM Travel Link is only avail-
able in select markets. For more information,
see www.sirius.com/travellink
“Made for iPodR” and “Made for iPhoneR”
mean that an electronic accessory has been
designed to connect specifically to iPod
Ror
iPhone
R, respectively, and has been certified
by the developer to meet Apple performance
standards. Apple is not responsible for the
operation of this device or its compliance with
safety and regulatory standards. Please note
that the use of this accessory with iPod
Ror
iPhone
Rmay affect wireless performance.
Apple, the Apple logo, iPhone
R, iPodR, iPod
classic
R, iPod nanoR, and iPod touchRare trademarks of Apple Inc., registered in the
U.S. and other countries. Lightning is a trade-
mark of Apple Inc. App Store is a service mark of
Apple Inc.
Music recognition technology and related data
are provided by Gracenote®. Gracenote is the
industry standard in music recognition technol-
ogy and related content delivery. For more
information, visit www.gracenote.com.
CD and music-related data from Gracenote, Inc.,
copyright
c2000 to present Gracenote.
Gracenote Software, copyright
c2000 to pres-
ent Gracenote. One or more patents owned by
Gracenote apply to this product and service.
See the Gracenote website for a non-exhaustive
list of applicable Gracenote patents. Gracenote,
CDDB, MusicID, MediaVOCS, the Gracenote
logo and logotype, and the “Powered by
Gracenote” logo are either registered trade-
marks or trademarks of Gracenote in the United
States and/or other countries.
App Store
SM
Apple and the Apple logo are trademarks of Apple
Inc., registered in the U.S. and other countries.
App Store is a service mark of Apple Inc.
Google PlayTM
Google Play is a trademark of Google Inc.
Google
c2012 Google Inc. All rights reserved. Google
CalendarTMcalendaring application is a trade-
mark of Google Inc.
Display screen, heater and air conditioner, and audio system4-55

NAMES AND FUNCTIONS OF AUDIO
CONTROL BUTTONS
Main audio buttons
1:Functions to seek radio stations or to skip
and fast-forward/rewind through tracks.
2<>:
Push to eject a disc.
3:
Push to switch to the radio mode. The
radio band will switch between AM, FM,
and SXM (SiriusXM) each time the but-
ton is pushed.
4:
Each time the button is pushed, a differ-
ent audio source (CD, iPod, USB or
Bluetooth® Streaming Audio) will be
selected.
5Disc slot:
Insert a disc with the label side facing
up.
6:
Functions to manually tune AM/FM , to
select SXM categories and to select
MP3/WMA/AAC folders.
7Radio memory buttons:Up to six pre-
ferred stations can be registered in the
preset list for each band.
8:
Push to turn the audio system on/off.
Turn to adjust the volume.
Audio APPS information will be displayed when
music is played via INFINITI InTouch Apps.
NAA1704
4-64Display screen, heater and air conditioner, and audio system

Selecting audio source
1. Turn on the audio source menu screen by
touching [Source] on the upper left corner of
the audio screen.
2. Select an item from the audio source menu
screen.
•Pushingorcan also
change the audio source.
SeeMain audio buttonsearlier in this
section.
•If the audio system has been turned off
while one of the audio sources was playing,
turning the audio system back on will play
the audio source that was playing when the
system was turned off.
•The audio source can also be changed with
the source bar on top of the audio screen.
•Audio APPS information will be displayed
when music is played via INFINITI InTouch
Apps.
Audio source bar
The audio source can be changed with the
source bar on top of the audio screen. The
source bar display can be turned on/off.
Turning source bar on/off
:
You can select whether the source bar on top of
the audio screens is displayed or not.1. Touch [Source] on the upper left corner of
the audio screen.
2. Touch [Show Source Bar] to turn the indica-
tor on/off.
Editing source bar
:
The audio sources to be displayed on the
source bar can be changed.
1. Touch [Source] on the upper left corner of
the audio screen.
2. Touch [Edit Source Bar].
3. Touch one of the keys on the source bar and
then touch one of the audio sources from the
source list to register the audio source in the
source bar.
NAA1714NAA1715
4-66Display screen, heater and air conditioner, and audio system