service indicator INFINITI QX30 2017 User Guide

Driving systems
Message Possible causes/consequences and solutions
[Lane Departure Warning
Currently Unavailable See
Operator’s Manual]Lane Departure Warning is deactivated and temporarily inoperative.
Possible causes:
•The windshield is dirty in the camera’s field of vision.•Visibility is impaired due to heavy rain, snow or fog.•There have been no lane markings for an extended period.•The lane markings are worn, dark or covered, e.g. by dirt or snow.
Once the causes listed above no longer apply, the display message goes out.
Lane Departure Warning is operational again.
If the display message does not disappear:
1. Pull over and stop the vehicle safely as soon as possible, paying attention to road and traffic conditions, and switch off the engine.
2. Secure the vehicle against rolling away.
3. Clean the windshield
[Lane Departure Warning
Inoperative]Lane Departure Warning is faulty.
Have the system checked. It is recommended you visit an INFINITI retailer for this service.
[Blind Spot Warning Cur-
rently Unavailable See Op-
erator’s Manual]Blind Spot Warning is temporarily inoperative. Possible causes:
•The function is impaired due to heavy rain or snow.•The radar sensor system is temporarily inoperative, e.g. due to electromagnetic radiation emitted by nearby TV or radio stations or
other sources of electromagnetic radiation.
•The radar sensor system is outside the operating temperature range.
The yellow indicator lights also light up in the exterior mirrors.
Once the causes listed above no longer apply, the display message goes out.
Blind Spot Warning is operational again.
If the display message does not disappear:
1. Pull over and stop the vehicle safely as soon as possible, paying attention to road and traffic conditions, and switch off the engine.
2. Secure the vehicle against rolling away.
3. Restart the engine
2-46Instruments and controls

Message Possible causes/consequences and solutions
[Blind Spot Warning Not
Available When Towing a
Trailer See Operator’s
Manual]Blind Spot Warning is deactivated while towing a trailer.
You have established the electrical connection between the trailer and your vehicle.
Press on the steering wheel to confirm the display message.
[Blind Spot Warning
Inoperative]Blind Spot Warning (BSW) is faulty.
The BSW indicator lights also light up.
Have the system checked. It is recommended you visit an INFINITI retailer for this service.
[Park Assist Canceled] The driver’s door is open and the driver’s seat belt has not been fastened.
Repeat the parking process with the seat belt fastened and the driver’s door closed.
You inadvertently touched the steering wheel while steering intervention was active.
While steering intervention is active, make sure not to touch the steering wheel.
The vehicle has started to skid and VDC has intervened.
Use Intelligent Park Assist again later.
[Park Assist Inoperative] You have just carried out a large number of turning or parking maneuvers.
Intelligent Park Assist will become available again after approximately ten minutes.
1. Pull over and stop the vehicle safely as soon as possible, paying attention to road and traffic conditions, and switch off the engine.
2. Restart the engine.
If the display message continues to be displayed, have the system checked. It is recommended you visit an INFINITI retailer for this
service.
The parking sensor system is faulty.
Have the system checked. It is recommended you visit an INFINITI retailer for this service.
[Park Assist Finished] The vehicle is parked. A warning tone also sounds.
The display message disappears automatically.
[ICC Off]
Intelligent Cruise Control has been deactivated (seeIntelligent Cruise Control (ICC) system (Full speed range) (if equipped)in the5.
Starting and drivingsection).
If it was not deactivated by the driver, a warning tone also sounds.
Instruments and controls2-47

•When cleaning the seat, never use gaso-
line, benzine, thinner, or any similar mate-
rials.
•If any malfunctions are found or the heated
seat does not operate, turn the switch off
and have the system checked. It is recom-
mended you visit an INFINITI retailer for this
service.
The front seats are warmed by built-in heaters.
The switches are located on the center console
and can be operated independently, for the
left-hand side seat and for the right-hand side
seat.
The three red indicator lights in the button
indicate the heating level you have selected The
system automatically switches from level 3 to
level 2 after approximately eight minutes The
system automatically switches from level 2 to
level 1 after approximately ten minutes. The
system automatically switches off approxi-
mately 20 minutes after it is set to level 1
1. Turn the ignition switch to the ON position.
NOTE
The seat heater can only be activated when
the ignition switch is in the ON position.2. Start the engine.
3. Select the heat range:
•To switch on: press button1repeatedly
until the desired heating level is set.
•To switch off: press button1repeatedly
until all the indicator lights turn off.
NOTE
If the battery voltage is too low, the seat heating
may switch off.
NIC2634
2-70Instruments and controls

•Recommendation for air distribution in win-
ter: select theandsettings.
Recommendation for air distribution in sum-
mer: select the
orandsettings.
•Only use theWindshield demistingfunc-
tion briefly until the windshield is clear again
•Only use air-recirculation mode briefly, e. g
if there are unpleasant outside odors or
when in a tunnel. The windows could other-
wise mist up as no fresh air is drawn into the
vehicle in air-recirculation mode
•If you change the settings of the climate
control system, the climate status display
appears for approximately three seconds at
the bottom of the screen in the central
display (see separate operating instruc-
tions). You will see the current settings of the
various climate control functions.
Switching air-conditioning system
on/off
Make sure the ignition switch is in the ON
position.
To switch on:turn control
5clockwise to the
desired position (except position0).
To switch off:turn control
5counter-clockwise
to position0.
Activating/deactivating the cooling
with air dehumidification function
If you deactivate theCooling with air dehumidi-
ficationfunction, the air inside the vehicle will
not be cooled. The air inside the vehicle will
also not be dehumidified. The windows can mist
up more quickly. Therefore, only deactivate the
Cooling with air dehumidificationfunction
briefly.
TheCooling with air dehumidificationfunction
is only available when the engine is running.
The air inside the vehicle is cooled and dehu-
midified according to the temperature selected.
Condensation may drip from the underside of
the vehicle when cooling mode is active. This is
normal and not a sign that there is a malfunc-
tion.
To activate
:
Press thebutton The indicator lamp in
thebutton lights up.
To deactivate
:
Press thebutton. The indicator lamp in
thebutton goes out. The cooling with air
dehumidification function has a delayed switch-
off feature.Problems with theCooling with air dehumidifi-
cationfunction
:
Problem:The indicator lamp in thebutton flashes three times or remains off. The
cooling with air dehumidification function can-
not be activated.
Cause and solution:The cooling with air dehu-
midification function has been deactivated due
to a malfunction. Have the system checked. It is
recommended you visit an INFINITI retailer for
this service.
Setting the temperature
You can set the temperature for the entire
vehicle. The set temperature is automatically
maintained at a constant level.
To increase or reduce the temperature: turn
control
1counterclockwise or clockwise. Only
change the temperature setting in small incre-
ments. Start at 70
oF (22oC).
Setting the air distribution
Directs the airflow through the demis-
ter ventilators.
Directs the airflow through the center
and side air ventilators.
Directs the airflow through the footwell
air ventilators.
Display screen, heater and air conditioner, and audio system4-45

•Use thefunction to adopt the tem-
perature settings on the driver’s side for the
front-passenger side as well. The indicator
lamp in the
button goes out.
•If you change the settings of the climate
control system, the climate status display
appears for approximately three seconds at
the bottom of the screen in the center display
(see separate operating instructions). You
will see the current settings of the various
climate control functions.
Idle Stop/Start function
During automatic engine switch-off, the Climate
control only operates at a reduced capacity. If
you require the full climate control output, you
can switch off the Idle Stop/Start function by
pressing the ECO button (seeIdle Stop/Start
System (if equipped)in the5. Starting and
drivingsection).
Switching automatic climate control
on/off
When the climate control is switched off, the air
supply and air circulation are also switched off.
The windows could mist up. Therefore, only
switch off climate control briefly.
Make sure the ignition switch is in the ON
position.To activate
:
Press thebutton The indicator lamp in
thebutton lights up. Airflow and air
distribution are set to automatic mode.
or
Press the
button. The indicator lamp in
thebutton goes out. The previous set-
tings are reactivated.
To deactivate
:
Press thebutton. The indicator lamp in
thebutton lights up.
NOTE
Automatic climate control: switch on climate
control primarily using the
button.
Activating/deactivating the cooling
with air dehumidification function
If you deactivate theCooling with air dehumidifi-
cationfunction, the air inside the vehicle will not
be cooled. The air inside the vehicle will also not
be dehumidified. The windows can mist up more
quickly. Therefore, only deactivate theCooling
with air dehumidificationfunction briefly.
TheCooling with air dehumidificationfunction
is only available when the engine is running.
The air inside the vehicle is cooled and dehu-
midified according to the temperature selected.Condensation may drip from the underside of
the vehicle when cooling mode is active. This is
normal and not a sign that there is a malfunc-
tion.
To activate
:
Press thebutton The indicator lamp in
thebutton lights up.
To deactivate
:
Press thebutton. The indicator lamp in
thebutton goes out. The cooling with air
dehumidification function has a delayed switch-
off feature.
Problems with theCooling with air dehumidifi-
cationfunction
:
Problem:The indicator lamp in thebutton flashes three times or remains off. The
cooling with air dehumidification function can-
not be activated.
Cause and solution:The cooling with air dehu-
midification function has been deactivated due
to a malfunction. Have the system checked. It is
recommended you visit an INFINITI retailer for
this service.
Display screen, heater and air conditioner, and audio system4-49

Activating air recirculation mode:
Make sure the ignition switch is in the ON
position.
Press the
button. The indicator light in
thebutton lights up.
Air-recirculation mode is activated automati-
cally at high outside temperatures or high
levels of pollution. When air-recirculation mode
is activated automatically, the indicator light in
the
button is not lit. Outside air is added
after about 30 minutes.
Deactivating air recirculation mode
:
Press thebutton. The indicator light in
thebutton goes out.
NOTE
Air-recirculation mode is deactivated automati-
cally:
•After approximately five minutes at outside
temperatures below approximately 45oF(7oC).
•After approximately five minutes if theCool-
ing with air dehumidificationfunction is
deactivated.
•After approximately 30 minutes at outside
temperatures above approximately 45oF(7oC) if the cooling with air dehumidification
function is activated.
SERVICING AIR CONDITIONER
WARNING
The air conditioner system contains refriger-
ant under high pressure. To avoid personal in-
jury, any air conditioner service should be
done only by an experienced technician with
the proper equipment.
The air conditioner system in your vehicle is
charged with a refrigerant designed with the
environment in mind.
This refrigerant will not harm the earth’s ozone
layer.
Special charging equipment and lubricant are
required when servicing your vehicle’s air con-
ditioner. Using improper refrigerants or lubri-
cants will cause severe damage to the air
conditioner system. (SeeAir conditioner sys-
tem refrigerant and oil recommendationsin the
9. Maintenance and Schedulessection.)
An INFINITI retailer will be able to service your
environmentally friendly air conditioner system.
Air conditioner filter
The air conditioner system is equipped with an
air conditioner filter. To make sure the air
conditioner heats, defogs, and ventilates effi-
ciently, replace the filter in accordance with the
specified maintenance intervals listed in the
separate maintenance booklet. It is recom-
mended you visit an INFINITI retailer for this
service.
The filter should be replaced if the air flow
decreases significantly or if windows fog up
easily when operating the heater or air condi-
tioner.
4-52Display screen, heater and air conditioner, and audio system

CAUTION
•Do not use leaded gasoline. (SeeRecom-
mended fluids/lubricants and capacitiesin
the9. Maintenance and Schedulessec-
tion.) Deposits from leaded gasoline seri-
ously reduce the ability of the three-way
catalyst to help reduce exhaust pollutants
and/or damage the three-way catalyst.
•Keep your engine tuned up. Malfunctions in
the ignition, fuel injection, or electrical sys-
tems may cause overrich fuel to flow into
the three-way catalyst, causing it to over-
heat. Do not keep driving if the engine mis-
fires, or if noticeable loss of performance or
other unusual operating conditions are de-
tected. Have the vehicle inspected
promptly. It is recommended you visit an
INFINITI retailer for this service.
•Avoid driving with an extremely low fuel
level. Running out of fuel could cause the
engine to misfire, damaging the three-way
catalyst.
•Do not race the engine while warming it up.
•Do not push or tow your vehicle to start the
engine.
TIRE PRESSURE MONITORING SYSTEM
(TPMS)
Each tire, including the spare (if present),
should be checked monthly when cold and
inflated to the inflation pressure recommended
by the vehicle manufacturer on the vehicle
placard or tire inflation pressure label. (If your
vehicle has tires of a different size than the size
indicated on the vehicle placard or tire inflation
pressure label, you should determine the
proper tire inflation pressure for those tires.)
As an added safety feature, your vehicle has
been equipped with a tire pressure monitoring
system (TPMS) that illuminates a low tire pres-
sure telltale when one or more of your tires is
significantly under-inflated. Accordingly, when
the low tire pressure telltale illuminates, you
should stop and check your tires as soon as
possible, and inflate them to the proper pres-
sure. Driving on a significantly under-inflated
tire causes the tire to overheat and can lead to
tire failure. Under-inflation also reduces fuel
efficiency and tire tread life, and may affect the
vehicle’s handling and stopping ability.
Please note that the TPMS is not a substitute for
proper tire maintenance, and it is the driver’s
responsibility to maintain correct tire pressure,
even if under-inflation has not reached the level
to trigger illumination of the TPMS low tire
pressure telltale.
Your vehicle has also been equipped with a TPMS
malfunction indicator to indicate when the sys-
tem is not operating properly. The TPMS malfunc-
tion indicator is combined with the low tire
pressure telltale. When the system detects a
malfunction, the telltale will flash for approxi-
mately one minute and then remain continuously
illuminated. This sequence will continue upon
subsequent vehicle start-ups as long as the mal-
function exists. When the malfunction indicator is
illuminated, the system may not be able to detect
or signal low tire pressure as intended. TPMS
malfunctions may occur for a variety of reasons,
including the installation of replacement or alter-
nate tires or wheels on the vehicle that prevent
the TPMS from working properly. Always check
the TPMS telltale after replacing one or more tires
or wheels on your vehicle to ensure that the
replacement or alternate tires and wheels allow
the TPMS to continue to function properly.
The vehicle’s wheels have sensors fitted that
monitor the tire pressures in all four tires The
tire pressure monitor warns you if the pressure
drops in one or more of the tires The tire
pressure monitor only functions if the corre-
sponding sensors are fitted to all wheels.
Information on tire pressures is shown in the
vehicle information display. After a few minutes
of driving, the current tire pressure of each tire
is shown in the [Serv.] menu of the vehicle
information display.
Starting and driving5-5

PROBLEMS WITH PARKING SENSOR SYSTEM
Problem Possible causes/consequences and solutions
Only the red segments in the
Parking Sensor System displays are
lit. You also hear a warning tone for
approximately two seconds.
The Parking Sensor System is then
deactivated and the indicator light
on the Parking Sensor System
button lights up.The Parking Sensor System has malfunctioned and has been
deactivated.
If problems persist, have the Parking Sensor System checked. It is
recommended you visit an INFINITI retailer for this service.
Only the red segments in the
parking sensor displays are lit. The
Parking Sensor System is then
deactivated.The parking sensors are dirty or there is interference.
•Clean the sensors.•Switch the ignition back on.
The problem may be caused by an external source of radio or ultrasound
waves.
See if the Parking Sensor System functions in a different location.
During the first 1,200 miles (2,000 km), follow
these recommendations to obtain maximum
engine performance and ensure the future reli-
ability and economy of your new vehicle. Failure
to follow these recommendations may result in
shortened engine life and reduced engine per-
formance.
•Avoid driving for long periods at constant
speed, either fast or slow, and do not run the
engine over 4,000 RPM.
•Do not accelerate at full throttle in any gear.
•Avoid quick starts.
•Avoid hard braking as much as possible.
•Do not tow a trailer for the first 500 mi (805
km). Your engine, axle or other parts could
be damaged.
You should also observe these notes on
break-in if the engine or parts of the drive train
on your vehicle have been replaced.
BREAK-IN SCHEDULE
Starting and driving5-81

•When a replacement tire is mounted or a
wheel is replaced, the TPMS will not func-
tion and the low tire pressure warning light
will flash for approximately 1 minute. The
light will remain on after 1 minute. It is rec-
ommended you Contact an INFINITI retailer
as soon as possible for tire replacement
and/or system resetting.
•Replacing tires with those not originally
specified by INFINITI could affect the proper
operation of the TPMS.
•If you used Emergency Tire Sealant to repair
a minor tire puncture, the TPMS sensor
should be checked when repairing or re-
placing the tire. It is recommended you visit
an INFINITI retailer for this service.
The Tire Pressure Monitoring System (TPMS)
monitors tire pressure of all tires. When the low
tire pressure warning light is lit, and a tire
pressure-related warning (if equipped) appears
in the vehicle information display, one or more
of your tires is significantly under-inflated. If
the vehicle is being driven with low tire pres-
sure, the TPMS will activate and warn you of it
by the low tire pressure warning light (in the
meter panel). This system will activate only
when the vehicle is driven at speeds above 16MPH (25 km/h).
For more details about the TPMS, seeTire
Pressure Monitoring System (TPMS)in the5.
Starting and drivingStarting and drivingsec-
tion.
STOPPING VEHICLE
WARNING
•Be sure to apply the parking brake firmly.
•Be sure that P (Park) is engaged.
•Never change tires when the vehicle is on a
slope, ice or slippery area. This is hazard-
ous.
•Never change tires when the oncoming traf-
fic is close to your vehicle. Call for profes-
sional road assistance.
1. Safely move the vehicle off the road away
from traffic.
2. Turn on the hazard indicator flasher lights.
3. Park on a level surface.
4. Apply the parking brake.
5. Press the P (Park) button.6. Turn off the engine.
7. Open the hood and set up the triangle
reflector (if equipped):
•To warn other traffic.
•To signal professional road assistance
personnel that you need assistance.
8. Have all passengers get out of the vehicle
and stand in a safe place, away from other
traffic and clear of the vehicle.
In case of emergency6-3

•Tires degrade with age and use. Have tires,
including the spare, over 6 years old
checked by a qualified technician because
some tire damage may not be obvious. Re-
place the tires as necessary to prevent tire
failure and possible personal injury.
•Improper service of the spare tire may re-
sult in serious personal injury. If it is neces-
sary to repair the spare tire, it is recom-
mended that you visit an INFINITI retailer for
this service.
•For additional information regarding tires,
refer to “Important Tire Safety Information”
(US) or “Tire Safety Information” (Canada)
in the Warranty Information Booklet.
Tires should be periodically inspected for wear,
cracking, bulging or objects caught in the tread. If
excessive wear, cracks, bulging or deep cuts are
found, the tire should be replaced immediately.
The original tires have a built-in tread wear
indicator. When the wear indicator is visible,
the tire should be replaced.
Improper servicing of a tire may result in seri-
ous personal injury. If it is necessary to repair a
tire, it is recommended you contact an INFINITI
retailer.
TIRE ROTATION
INFINITI recommends rotating the tires every
5,000 miles (8,000 km).
For additional information on tire replacing
procedures, refer toFlat tirein the6. In case
of emergencysection.As soon as possible,
tighten the wheel nuts to the specified torque
with a torque wrench.
Wheel nut tightening torque: 96 ft-lb (130 N·m)
The wheel nuts must be kept tightened to speci-
fications at all times. It is recommended that
wheel nuts be tightened to specification at each
tire rotation interval.
WARNING
•After rotating the tires, check and adjust
the tire pressure.
•Do not include the spare tire in the tire
rotation.
•For additional information regarding tires,
refer toImportant Tire Safety Information
(US) orTire Safety Informationin the War-
ranty Information Booklet.
REPLACING WHEELS AND TIRES
WARNING
Do not install a deformed wheel or tire even if it
has been repaired. Such wheels or tires could
have structural damage and could fail without
warning.
When replacing a tire, use the same size, speed
rating and load carrying capacity as originally
equipped. (SeeWheels and Tiresin the9.
Maintenance and SchedulesMaintenance and
Schedulessection for recommended types and
sizes of tires and wheels.)
If the wheels are changed for any reason,
always replace with wheels which have the
same offset dimension. Wheels of a different
offset could cause early tire wear, possibly
degraded vehicle handling characteristics
and/or interference with the brake discs/
drums. Such interference can lead to decreased
braking efficiency and/or early brake pad/shoe
wear.
8-34Do-it-yourself