start stop button INFINITI QX30 2017 User Guide

The engine can be switched off automatically a
maximum of four times (initial stop, then three
subsequent stops) in succession. The
Idle Stop/Start symbol is shown in yellow in the
vehicle information display after the engine has
been started automatically for the fourth time.
When the
Idle Stop/Start symbol is
shown in green in the vehicle information dis-
play, automatic engine switch-off is again pos-
sible.
NOTE
If the hood is opened while the engine is running
and the Idle Stop/Start function is operational,
the engine will switch off automatically.
If the vehicle is brought to a standstill in D or N,
the Idle Stop/Start function switches off the
engine automatically.
AUTOMATIC ENGINE START
The engine is started automatically if:
•You switch off the Idle Stop/Start function
by pressing the ECO button.
•You engage Reverse R or Drive D.
•You unfasten your seat belt or open the
driver’s door.
•The vehicle starts to roll.
•The brake system requires this.
•The temperature in the vehicle interior devi-
ates from the set range.
•The system detects moisture on the wind-
shield when the air-conditioning system is
switched on.
•The battery’s charge status is too low.
The engine is started automatically if you:
•Release the brake pedal in transmission
position D (Drive) or N (Neutral).
•Depress the accelerator pedal.
•Move the transmission out of position P
(Park).
Shifting the transmission to position P (Park)
does not start the engine.
If you shift the transmission from R (Reverse) to
D (Drive), the Idle Stop/Start function is avail-
able again once the
Idle Stop/Start
symbol reappears in green in the vehicle infor-
mation display.
DEACTIVATING/ACTIVATING THE IDLE
STOP/START FUNCTION
•To deactivate:press ECO button1. Indica-
tor lamp
2and theIdle Stop/Start
symbol in the vehicle information display
turn off.
•To activate:press ECO button1. Indicator
lamp
2lights up. If all conditions for auto-
matic engine switch-off (seeAutomatic engine
switch-offearlier in this section) are fulfilled,
the
Idle Stop/Start symbol is shown in
green in the vehicle information display.
If not all conditions for automatic engine
switch-off are met, theIdle Stop/Start
symbol is lit yellow in the vehicle information
display. If this is the case, the Idle Stop/Start
function is not active.
NIC2633
5-28Starting and driving

If indicator lamp2on ECO button1is off, the
Idle Stop/Start function has been deactivated
manually or as the result of a malfunction. The
engine will then not be switched off automati-
cally when the vehicle stops.WARNING
Failure to follow the warnings and instructions
for proper use of the LDW system could result
in serious personal injury or death. The LDW
system will not steer the vehicle or prevent
loss of control. It is the driver’s responsibility
to stay alert, drive safely, keep the vehicle in
the traveling lane, and be in control of the
vehicle at all times.
The LDW system warns the driver with a warn-
ing light and intermittent steering vibration that
the vehicle is beginning to leave the traveling
lane.The LDW system uses a camera
1installed
behind the windshield to monitor the lane
markers of your traveling lane.
NSD644
LANE DEPARTURE WARNING (LDW)
SYSTEM (IF EQUIPPED)
Starting and driving5-29

1Steering wheel mounted controls
2Vehicle information display
ADisplay area
BMenu bar
LDW SYSTEM TEMPORARILY
UNAVAILABLE
Under the following conditions, the LDW system
will be canceled automatically, and the mes-
sage [Lane Departure Warning Currently Un-
available See Operator’s Manual] is displayed
in the vehicle information display
2. The LDW
system is temporarily unavailable.
•The windshield is dirty in the camera’s field
of vision.
•Visibility is impaired due to heavy rain, snow
or fog.
•There have been no lane markings for an
extended period.
•The lane markings are worn, dark, or cov-
ered by dirt or snow, etc..
Action to take:When the above conditions no
longer exist, the message goes out and the LDW
system is operational again. If the message
continues to appear, stop the vehicle in a safe
location, press the P (Park) button , and clean
the windshield.
NSD626
Starting and driving5-33

How to change the set vehicle speed
To cancel the preset speed, use any of these
methods:
•Tap the brake pedal when the vehicle is
moving.
•Quickly push the cruise control lever in the
direction of arrow
5.
The message [ICC OFF] appears in the vehicle
information display for 5 seconds.
To reset at a higher cruising speed, use one of
the following methods:
•Depress the accelerator pedal. When the
vehicle attains the desired speed, quickly
pull the cruise control lever towards you
3.
•Pull the cruise control lever up1beyond
the pressure point. The set vehicle speed will
increase by approximately 10 MPH (10 km/h).
•Pull the cruise control lever up (1) at the
pressure point. The set vehicle speed will
increase by approximately 1 MPH (1 km/h).
To reset at a lower cruising speed, use one of
the following methods:
•Lightly tap the brake pedal. When the ve-
hicle attains the desired speed, quickly pull
the cruise control lever towards you
3.
•Pull the cruise control lever down4beyond
the pressure point. The set vehicle speed will
decrease by approximately 10 MPH (10 km/h).
•Pull the cruise control lever down4to the
pressure point. The set vehicle speed will
decrease by approximately 1 MPH (1 km/h).
To resume the preset speed, quickly pull the
cruise control lever towards you
4. The vehicle
will resume the last set cruising speed when the
vehicle speed is over 20 MPH (30 km/h).
NOTE
If you do not fully release the accelerator pedal,
the [ICC Deactivated Automatically] message
appears in the vehicle information display. The
set distance to a slower-moving vehicle in front
will then not be maintained. You will be driving
at the speed you determine by the position of the
accelerator pedal.
You can also activate ICC when stationary. The
lowest speed that can be set is 20 MPH (30 km/h).
Stopping
WARNING
•To help avoid risk of injury or death through
unintended operation of the vehicle and/or
its systems, do not leave children, people
who require the assistance of others, or
pets unattended in your vehicle.
•The ICC system should only be used to keep
the vehicle stationary when the driver is
actively using the system. When parking
the vehicle, make sure to turn OFF the ICC
system, use the brake, press the PARK (P)
button, and place the ignition switch in the
LOCK position prior to exiting the vehicle.
Failure to do so could lead to serious injury
or death. The ICC system will not hold the
vehicle in place after coming to a stop when
any of the following conditions occur:
–There is a malfunction in the system or
in the voltage supply.
–The ICC system has been deactivated
with the cruise control lever, e. g. by a
vehicle occupant.
–The accelerator pedal has been de-
pressed, e.g. by a vehicle occupant.NSD582A
5-52Starting and driving

1Detected parking space on the left.
2Parking symbol.
3Detected parking space on the right.
IPA is activated automatically when driving for-
wards. The system is operational at speeds of
up to approximately 19 MPH (30 km/h). While in
operation, the system independently locates
and measures parking spaces on both sides of
the vehicle
IPA will only detect parking spaces:
•Adjacent to the vehicle.
•Parallel or at right angles to the direction of
travel.
•That are parallel to the direction of travel
and are at least 5 ft (1.5 m) wide.
•That are parallel to the direction of travel
and at least 3.3 ft (1.0 m) longer than your
vehicle.
•That are at right angles to the direction of
travel and at least 3.3 ft (1.0 m) wider than
your vehicle.
NOTE
IPA cannot measure the length of a parking
space if it is at right angles to the direction of
travel. You will need to judge whether your ve-
hicle will fit in the parking space
When driving at speeds below 19 MPH (30
km/h) you will see parking symbol
2as a
status indicator in the vehicle information dis-
play. When a parking space has been detected,
an arrow towards the right
3or the left1also
appears. IPA only displays parking spaces on
the front-passenger side as standard. Parking
spaces on the driver’s side are displayed as
soon as the turn signal on the driver’s side is
activated. When parking on the driver’s side,
this must remain activated until you confirm the
use of IPA by pressing thebutton on the
steering wheel. The system automatically deter-
mines whether the parking space is parallel or
at right angles to the direction of travel.
A parking space is displayed while you are
driving past it, and until you are approximately
50 ft (15 m) away from it.
PARKING
NOTE
When the parking sensor system detects ob-
stacles, you are responsible for braking in good
time.
1. Stop the vehicle when the parking symbol
shows the desired parking space in the
combination meter
2. Shift into position R.
The [Start Park Assist? Yes: OK No:]
message appears in the vehicle information
display.
3. To cancel the procedure: press the
button on the steering wheel or pull away
or
4. To park using IPA press thebutton on
the steering wheel. The Park Assist [Observe
surroundings] message appears in the ve-
hicle information display.
5. Release the steering wheel.
6. Back up the vehicle, being ready to brake at
all times. When backing up, drive at a speed
below 5 MPH (10 km/h). Otherwise, IPA will
be canceled.
NSD612Upper display
5-70Starting and driving

EXITING A PARKING SPACE
In order that IPA can support when exiting the
parking space:
•You need to have parked using IPA.
•The border of the parking space must be
high enough at the front and the rear. A curb
stone is too small, for example.
•The border of the parking space must not be
too wide, as the position of the vehicle must
not exceed an angle of 45 degrees to the
starting position as it is manoeuvred into the
parking space.
•A total front and back maneuvering distance
of at least 1.0 m must be available.
IPA can only assist you with exiting a parking
space if you have parked the vehicle parallel to
the direction of travel using IPA.
WARNING
•IPA is only an aid. It is not a substitute for
your attention to the immediate surround-
ings. The responsibility for safe maneuver-
ing and parking remains with you.
•Make sure that no persons, animals or ob-
jects are in the maneuvering range.
•When the parking sensor system is deacti-
vated, IPA is also unavailable.
•While parking or pulling out of a parking
space, the vehicle swings out and can drive
onto areas of the oncoming lane. This could
cause you to collide with other road users.
There is a risk of an accident.
•Pay attention to other road users. Stop the
vehicle if necessary or cancel the IPA park-
ing procedure.
1. Start the engine.
2. Release the electric parking brake.
3. Switch on the turn signal in the direction
you are pulling away.
4.Vehicles with automatic transmission:shift
the transmission to position D or R
The [Start Park Assist? Yes: OK No:]
message appears in the vehicle information
display.
5. To cancel the procedure: press the
button on the steering wheel or pull away
or
6. To exit a parking space using IPA: press the
button on the steering wheel The ParkAssist [Observe surroundings] message ap-
pears in the display.
7. Release the steering wheel.
8.
Pull away, being ready to brake at all times
Do not exceed a maximum speed of approxi-
mately 5 MPH (10 km/h) when exiting a park-
ing space. Otherwise, IPA will be canceled.
WARNING
While parking or pulling out of a parking
space, the vehicle swings out and can drive
onto areas of the oncoming lane. This could
cause you to collide with other road users.
There is a risk of an accident.
9. Depending on the message or as required,
shift the transmission to position D or R.
IPA immediately steers in the other direc-
tion. The [Observe surroundings] message
appears in the display.
NOTE
You will achieve the best results by waiting
for the steering procedure to complete before
pulling away.
If you back up after activation, the steering
wheel is moved to the straight-ahead posi-
tion.
5-72Starting and driving

•When a replacement tire is mounted or a
wheel is replaced, the TPMS will not func-
tion and the low tire pressure warning light
will flash for approximately 1 minute. The
light will remain on after 1 minute. It is rec-
ommended you Contact an INFINITI retailer
as soon as possible for tire replacement
and/or system resetting.
•Replacing tires with those not originally
specified by INFINITI could affect the proper
operation of the TPMS.
•If you used Emergency Tire Sealant to repair
a minor tire puncture, the TPMS sensor
should be checked when repairing or re-
placing the tire. It is recommended you visit
an INFINITI retailer for this service.
The Tire Pressure Monitoring System (TPMS)
monitors tire pressure of all tires. When the low
tire pressure warning light is lit, and a tire
pressure-related warning (if equipped) appears
in the vehicle information display, one or more
of your tires is significantly under-inflated. If
the vehicle is being driven with low tire pres-
sure, the TPMS will activate and warn you of it
by the low tire pressure warning light (in the
meter panel). This system will activate only
when the vehicle is driven at speeds above 16MPH (25 km/h).
For more details about the TPMS, seeTire
Pressure Monitoring System (TPMS)in the5.
Starting and drivingStarting and drivingsec-
tion.
STOPPING VEHICLE
WARNING
•Be sure to apply the parking brake firmly.
•Be sure that P (Park) is engaged.
•Never change tires when the vehicle is on a
slope, ice or slippery area. This is hazard-
ous.
•Never change tires when the oncoming traf-
fic is close to your vehicle. Call for profes-
sional road assistance.
1. Safely move the vehicle off the road away
from traffic.
2. Turn on the hazard indicator flasher lights.
3. Park on a level surface.
4. Apply the parking brake.
5. Press the P (Park) button.6. Turn off the engine.
7. Open the hood and set up the triangle
reflector (if equipped):
•To warn other traffic.
•To signal professional road assistance
personnel that you need assistance.
8. Have all passengers get out of the vehicle
and stand in a safe place, away from other
traffic and clear of the vehicle.
In case of emergency6-3

WARNING
•Do not continue to drive if your vehicle over-
heats. Doing so could cause engine damage
or a vehicle fire.
•To avoid the danger of being scalded, never
remove the radiator or coolant reservoir cap
while the engine is hot. When the radiator or
coolant reservoir cap is removed, pressur-
ized hot water will spurt out, possibly caus-
ing serious injury.
•Do not open the hood if steam is coming
out.
If the engine of your vehicle is overheating
(indicated by the engine coolant temperature
gauge) or if you feel a lack of engine power,
detect unusual noise, etc., proceed as follows:
1. Move and park the vehicle safely off the
road and away from traffic.
2. Turn on the hazard warning flasher lights.
3. Apply the parking brake.
4. Press the P (Park) button.
DO NOT STOP THE ENGINE.
5. Open all windows.6. Switch off the air conditioner system (if
equipped).
7. Set the heater or air conditioner tempera-
ture control to maximum “HOT” and fan
speed control to maximum speed.
8. Exit the vehicle.
9. Visually inspect and listen for steam or
coolant escaping from the radiator before
opening the hood.WARNING
If steam or water is coming from the engine,
stand clear to prevent getting burned.
10. Open the hood. For details, seeHoodin
the3. Pre-driving checks and adjustments
section.
11. Visually check if the cooling fan is running.
12. Visually check the radiator and radiator
hoses for leakage.
WARNING
Be careful not to allow your hands, hair, jew-
elry or clothing to come into contact with, or
get caught in, engine belts or the engine cool-
ing fan. The engine cooling fan can start at any
time.
13. After the engine cools down, check the
coolant level in the engine coolant reservoir
with the engine running.Do not open the
radiator cap (if equipped).
14. If the level is low, remove the engine
coolant reservoir cap and add coolant
slowly into the reservoir. After refilling the
reservoir to the MAX level, install the res-
ervoir cap.
15. Close the hood.
Have your vehicle inspected or repaired. It is
recommended you visit an INFINITI retailer.
IF YOUR VEHICLE OVERHEATS
In case of emergency6-13