warning lights INFINITI QX30 2017 User Guide

•The coolant is too hot and the engine is no
longer being cooled sufficiently.
Observe the additional display messages in the
vehicle information display.
Stop the vehicle immediately, paying attention
to road and traffic conditions, and switch off the
engine.
Secure the vehicle against rolling away.
Leave the vehicle and keep a safe distance from
the vehicle until the engine has cooled down.
Check the coolant level and top up the coolant,
observing the warning notes (seeIf your ve-
hicle overheatsin the6. In case of emergency
section).
If you have to top up the coolant frequently,
have the engine cooling system checked.
Make sure that the air supply to the engine
radiator is not blocked, e. g. by frozen slush.
Do not start the engine again until the coolant
temperature is below 250
oF (120oC). The
engine may otherwise be damaged.
Low fuel warning light
This light comes on when the fuel level in the
fuel tank is getting low. Refuel as soon as it is
convenient, preferably before the fuel gauge
reaches 0 (Empty).There will be a small reserve
of fuel in the tank when the fuel gauge reaches 0
(Empty).
Vehicle Dynamic Control
(VDC) warning light
The VDC warning light blinks when the Vehicle
Dynamic Control (VDC) system is operating,
thus alerting the driver to the fact that the road
surface is slippery and the vehicle is nearing its
traction limits.
You may feel or hear the system working, this is
normal.
The light will continue to blink for a few seconds
after the VDC system stops limiting wheel spin.
Cruise control or Intelligent Cruise Control is
deactivated.
For additional information seeVehicle Dy-
namic Control (VDC) OFF indicator lightin the
2. Instruments and controlssection andVe-
hicle Dynamic Control (VDC) systemin the5.
Starting and drivingStarting and drivingsec-
tion.
INDICATOR LIGHTS
Turn signal/hazard indicator
lights
The appropriate light flashes when the turn
signal switch is activated. Both lights flash
when the hazard switch is turned on.
Low beam indicator light
This light comes on when the switch is turned to
the position:The headlights will come on
and front side, tail, number plate and instru-
ment lights remain on.
Vehicle Dynamic Control (VDC)
OFF indicator light
The light comes on when the Vehicle Dynamic
Control (VDC) has been disabled. This indicates
that the VDC system is not operating.
Disabling the VDC system causes the Forward
Emergency Braking system to become unavail-
able. SeeForward emergency braking (FEB)
system (if equipped)in the5. Starting and
drivingsection for more details.
This light also comes on briefly when the igni-
tion switch is turned to the ON position. The
light will turn off after approximately 1 second if
the VDC system is operational.
Instruments and controls2-13

When the VDC OFF indicator light and VDC
warning light (seeVehicle Dynamic Control
(VDC) warning lightlater in this section) come
on with the VDC system turned on, it alerts the
driver to the fact that the system’s fail-safe
mode is operating. This means that the system
may not be functioning properly. Have the
system checked. It is recommended you visit an
INFINITI retailer for these services.
If an abnormality occurs in the system, the VDC
system function will be canceled, but the ve-
hicle is still driveable. For additional informa-
tion, seeVehicle Dynamic Control (VDC)
systemin the5. Starting and drivingsection.
WARNING
VDC should remain on unless freeing a vehicle
from mud or snow.
While the VDC system is operating, you might
feel a slight vibration or hear the system work-
ing when starting the vehicle or accelerating,
but this is normal.
Front fog light indicator light (if
equipped)
The light comes on when the front fog lights are
switched on (seeFog light switch (If so
equipped)later in this section).
High beam assist indicator light
(if equipped)
The indicator light illuminates when the head-
lights come on while the headlight switch is in
the AUTO position with the high beam selected.
This indicates that the high beam assist system
is operational. (See 2-62.)
High beam indicator light
This blue light comes on when the headlight
high beams are on and goes out when the low
beams are selected.
The high beam indicator light also comes on
when the passing signal is activated.
Rear fog light indicator light
The light comes on when the rear fog light is
switched on (seeFog light switch (If so
equipped)later in this section).
Side light and headlight
indicator light
This light comes on when the side light or
headlight position is selected, seeHeadlight
and turn signal switcheslater in this section
for further details.
/Front passenger air
bag status light
The front passenger air bag status light ()
located on the center console above the shift
lever will illuminate when the front passenger
air bag is turned OFF. When the front passenger
air bag is turned on, the front passenger air bag
status light ON (
) will illuminate.
For more details, seeFront passenger air bag
and status lightin the1. Safety — seats, seat
belts and supplemental restraint systemsec-
tion.
AUDIBLE REMINDERS
Parking brake reminder chime
A chime will sound when driving away if the
parking brake has not been released. Stop the
vehicle and release the parking brake.
Light reminder chime
With the ignition switch placed in the OFF
position, a chime sounds when the driver’s door
is opened if the side lights are on. Turn the
headlight control switch off before leaving the
vehicle.
2-14Instruments and controls

•Lane Departure Warning (LDW)
•Blind Spot Warning (BSW)
•Rear window wiper
Deactivating/activating VDC
:
The vehicle should be driven with the Vehicle
Dynamic Control (VDC) system on for most
driving conditions.
If the vehicle is stuck in mud or snow, the VDC
system reduces the engine output to reduce
wheel spin. The engine speed will be reduced
even if the accelerator is depressed to the floor.
If maximum engine power is needed to free a
stuck vehicle, turn the VDC system off.
For further information about VDC, seeVehicle
Dynamic Control (VDC) systemin the5. Starting
and drivingsection.
1. Start the engine.
2. Press the
orbutton on the
steering wheel to select the [DriveAssist]
menu.
3. Press the
orbutton to select
[ESP].
4. Press the button.
The current selection is displayed.5. To activate/deactivate: press the but-
ton again.
VDC is deactivated if the
warning light
in the combination meter lights up continu-
ously when the engine is running.
If both the
warning light andwarning light are lit continuously, VDC is not
available due to a malfunction.
Activating/deactivating Forward Emergency
Braking
:
1. Press theorbutton on the
steering wheel to select the [DriveAssist]
menu.
2. Press the
orbutton to select
[Emergency Brake].
3. Press the button.
The current selection is displayed.
4. To activate/deactivate: press the but-
ton again.
When Forward Emergency Braking is deacti-
vated, the
symbol appears in the
vehicle information display in the assistance
graphic display.
For further information about Forward Emergency
Braking, seeForward emergency braking (FEB)
system (if equipped)in the5. Starting and
drivingsection.
Activating/deactivating Blind Spot Warning
(BSW):
1. Press theorbutton on the
steering wheel to select the [DriveAssist]
menu.
2. Press the
orbutton to select
[Blind Spot Warning].
3. Press the button.
The current selection is displayed.
4. To activate/deactivate: press the but-
ton again.
For further information about Blind Spot Warn-
ing, seeBlind Spot Warning (BSW) system (if
equipped)in the5. Starting and drivingsec-
tion.
Instruments and controls2-23

2. Press theorbutton to select
[Convenience] submenu.
3. Press to confirm.
4. Press the
orbutton to select
the [Fold Mirrors in when Locking] function.
If the [Fold Mirrors in when Locking] function
is activated, the vehicle’s exterior mirror is
shown in orange in the vehicle information
display.
5. Press the button to save the setting.
Resetting to factory settings
1. Press theorbutton on the
steering wheel to select the [Settings] menu.
2. Press the
orbutton to select
[Factory Setting] submenu.
3. Press to confirm.
The [Reset All Settings?] message appears.
4. Press the
orbutton to select
[No] or [Yes].
5. Press the button to confirm the selec-
tion.
If you have selected [Yes], the vehicle infor-
mation display shows a confirmation mes-
sage.For safety reasons, not all functions are reset:
the [Limit Speed (Winter Tires)] function in
permanent speed limiter can only be set in the
[Vehicle] submenu.
If you want to reset the Daytime driving lights
function in the Lights submenu, you must
switch the ignition switch to the ACC position.
DISPLAY MESSAGES
Display messages appear in the vehicle infor-
mation display.
Display messages with graphic symbols are
simplified in the Owner’s Manual and may differ
from the symbols in the vehicle information
display.
Certain display messages are accompanied by
an audible warning tone or a continuous tone.
When the ignition is switched off, all display
messages are deleted apart from some high-
priority display messages. Once the causes of
the high-priority display messages have been
rectified, these display messages are deleted
as well.
When you stop and park the vehicle, please
observe the notes on parking (seeParkingin
the5. Starting and drivingsection).
Hiding display messages
Press the orbutton to hide the
display message. The display message is hid-
den.
The vehicle information display shows high-
priority display messages in red. Some high-
priority display messages cannot be hidden.
The vehicle information display shows these
messages continuously until the causes for the
messages have been remedied.
Message memory
The vehicle information display saves certain
messages in the message memory. You can call
up these display messages:
1. Press the
orbutton on the
steering wheel to select the [Service] menu.
If there are display messages, the vehicle
information display shows [2 messages], for
example.
2. Press the
orbutton to select
the entry, e.g. [2 messages].
3. Press to confirm.
4. Press the
orbutton to scroll
through the display messages.
Instruments and controls2-29

Safety systems
Message Possible causes/consequences and solutions
[Currently Unavailable See
Operator’s Manual]ABS (Anti-Lock Braking System), BAS (Brake Assist System), VDC (Vehicle Dynamic Control), and hill start assist are temporarily
unavailable.
Forward Emergency Braking (FEB) may also have failed.
In addition, the
,andwarning lights may light up in the combination meter.
Possible causes:
•Self-diagnosis is not yet complete.•The on-board voltage may be insufficient.
WARNING
The brake system continues to function normally, but without the functions listed above. The wheels could therefore lock if you brake hard,
for example.
The steering and braking characteristics may be severely affected. The braking distance may increase in an emergency braking situation.
If VDC is not operational, VDC is unable to stabilize the vehicle. There is an increased danger of skidding and risk of an accident.
Carefully drive on a suitable stretch of road, making slight steering movements, at a speed above 12 MPH (20 km/h). If the display
message disappears, the functions mentioned above are available again.
If the display message continues to be displayed, drive on carefully and have the system checked. It is recommended you visit an INFINITI
retailer for this service.
[Inoperative See Operator’s
Manual]ABS (Anti-Lock Braking System), BAS (Brake Assist System), VDC (Vehicle Dynamic Control), and hill start assist are not available due to
a malfunction.
Forward Emergency Braking (FEB) may also have failed.
In addition, the
,,andwarning lights may light up in the combination meter.
WARNING
The brake system continues to function normally, but without the functions listed above. The wheels could therefore lock if you brake hard,
for example.
The steering and braking characteristics may be severely affected. The braking distance may increase in an emergency braking situation.
If VDC is not operational, VDC is unable to stabilize the vehicle. There is an increased danger of skidding and risk of an accident.
Drive on carefully and have the system checked immediately. It is recommended you visit an INFINITI retailer for this service.
2-30Instruments and controls

Message Possible causes/consequences and solutions
[Currently Unavailable See
Operator’s Manual]BAS (Brake Assist System), VDC (Vehicle Dynamic Control), and hill start assist are temporarily unavailable.
Forward Emergency Braking (FEB) may also have failed.
In addition, the
andwarning lights may light up in the combination meter.
The self-diagnosis function, for example, may not be complete.
WARNING
The brake system continues to function normally, but without the functions listed above.
The braking distance may increase in an emergency braking situation.
If VDC is not operational, VDC is unable to stabilize the vehicle. There is an increased danger of skidding and risk of an accident.
Carefully drive on a suitable stretch of road, making slight steering movements, at a speed above 12 MPH(20 km/h). If the display
message disappears, the functions mentioned above are available again.
If the display message continues to be displayed, drive on carefully and have the system checked. It is recommended you an INFINITI
retailer for this service.
[Inoperative See Operator’s
Manual]BAS (Brake Assist System), VDC (Vehicle Dynamic Control), and hill start assist are not available due to a malfunction.
Forward Emergency Braking (FEB) may also have failed.
In addition, the
andwarning lights may light up in the combination meter.
WARNING
The brake system continues to function normally, but without the functions listed above.
The braking distance may increase in an emergency braking situation.
If VDC is not operational, VDC is unable to stabilize the vehicle. There is an increased danger of skidding and risk of an accident.
Drive on carefully and have the system checked. It is recommended you visit an INFINITI retailer for this service.
Instruments and controls2-31

Message Possible causes/consequences and solutions
[Inoperative See Operator’s
Manual]EBD (electronic brake force distribution) ABS (Anti-Lock Braking System), BAS (Brake Assist System), VDC (Vehicle Dynamic Contro), and
hill start assist are not available due to a malfunction.
Forward Emergency Braking (FEB) may also have failed.
A warning tone sounds.
In addition, the
,andwarning lights may light up in the combination meter.
WARNING
The brake system continues to function normally, but without the functions listed above. The front and rear wheels could therefore lock if
you brake hard, for example.
The steering and braking characteristics may be severely affected. The braking distance may increase in an emergency braking situation.
If VDC is not operational, VDC is unable to stabilize the vehicle. There is an increased danger of skidding and risk of an accident.
Drive on carefully and have the system checked immediately. It is recommended you visit an INFINITI retailer for this service.
[Turn On The Ignition to Re-
lease the Parking Brake]The redindicator light lights up.
You attempted to release the electric parking brake while the ignition was switched off.
Key: turn the key to the ON position in the ignition switch
[Please Release Parking
Brake]The redindicator light flashes and a warning tone sounds. A condition for automatic release of the electric parking brake is not
fulfilled (seeApplying automatically (vehicles with automatic transmission)in the5. Starting and drivingsection).
You are driving with the electric parking brake applied.
Release the electric parking brake manually.
The red
indicator light flashes and a warning tone sounds.
You are making an emergency stop using the electric parking brake (seeEmergency brakingin the5. Starting and drivingsection)
[Parking Brake See Opera-
tor’s Manual]The yellowwarning light lights up.
The electric parking brake is malfunctioning.
To apply:
1. Switch the ignition off.
2. Press the electric parking brake handle for at least ten seconds.
3. Press the P (Park) button.
4. Have the system checked. It is recommended you consult an INFINITI retailer.
2-32Instruments and controls

Message Possible causes/consequences and solutions
[Check Brake Fluid Level]There is insufficient brake fluid in the brake fluid reservoir.
In addition, the redwarning light lights up in the combination meter and a warning tone sounds.
1. Pull over and stop the vehicle safely as soon as possible, paying attention to road and traffic conditions. Do not continue driving under
any circumstances.
2. Secure the vehicle against rolling away.
3. Check the brake fluid level. If brake fluid is necessary, add fluid and have the system checked. It is recommended you visit an INFINITI
retailer for this service. SeeBrake fluidin the8. Do-it-yourselfsection.
4. If the brake fluid level is correct, have the warning system checked. It is recommended you visit an INFINITI retailer for this service.
WARNING•Your brake system may not be working properly if the warning light is on. Driving could be dangerous. If you judge it to be safe, drive
carefully to the nearest service station for repairs. Otherwise, have your vehicle towed because driving it could be dangerous.
•Pressing the brake pedal with the engine stopped and/or low brake fluid level may increase your stopping distance and braking will
require greater pedal effort as well as pedal travel.
•If the brake fluid level is below the minimum or MIN mark on the brake fluid reservoir, do not drive until the brake system has been
checked. It is recommended you visit an INFINITI retailer for this service.
[Check Brake Pad Wear]The brake pads/linings have reached their wear limit.
It is recommended you visit an INFINITI retailer.
[Emergency Brake Currently
Unavailable See Operator’s
Manual]Forward Emergency Braking is temporarily inoperative.
Possible causes:
•The radar sensor system is temporarily inoperative, e.g. due to electromagnetic radiation emitted by nearby TV or radio stations or
other sources of electromagnetic radiation.
•The system is outside the operating temperature range.•The on-board voltage is too low.
Once the causes listed above no longer apply, the display message goes out.
Forward Emergency Braking is operational again.
If the display message does not disappear:
1. Pull over and stop the vehicle safely as soon as possible, paying attention to road and traffic conditions.
2. Secure the vehicle against rolling away.
3. Restart the engine.
2-36Instruments and controls

Message Possible causes/consequences and solutions
[Emergency Brake
Inoperative]Forward Emergency Braking is temporarily inoperative due to a malfunction.
Have the system checked. It is recommended you visit an INFINITI retailer for this service.
[Radar Sensor (See
Operator’s Manual):]At least one of the following driving systems or driving safety systems is temporarily restricted or inoperative:
•Forward Emergency Braking•Intelligent Cruise Control
Possible causes:
•The sensors in the radiator trim and/or in the bumpers are dirty.•The function of the driving system and/or driving safety system is impaired due to heavy rain or snow.
A warning tone also sounds.
Once the causes listed above no longer apply, the display message goes out. All driving systems/driving safety systems are operative
again.
If the display message does not disappear:
1. Pull over and stop the vehicle safely as soon as possible, paying attention to road and traffic conditions
2. Secure the vehicle against rolling away.
3. Switch off the engine.
4. Clean the sensors in the following locations:
- In the radiator trim
- In the front bumper
- In the rear bumper, particularly in the middle of the rear bumper.
5. Restart the engine. The display message disappears.
[SRS Malfunction Service
Required]The restraint system needs servicing. Thewarning light also lights up in the combination meter.
It is recommended you visit an INFINITI retailer for these services.
Unless checked and repaired, the Supplemental Restraint Systems and/or the pretensioner seat belt may not function properly.
WARNING
If this light is on, it could mean that the front air bag, side air bag, curtain air bag systems and/or pretensioner systems will not operate in
an accident. To help avoid injury to yourself or others, have your vehicle checked as soon as possible. It is recommended you visit an INFINITI
retailer for this service.
For further information about the restraint system, seeSupplemental Restraint System (SRS)in the1. Safety — seats, seat belts and
supplemental restraint systemsection.
Instruments and controls2-37

Message Possible causes/consequences and solutions
[Check Left Daytime Running
Light] or [Check Right Day-
time Running Light]The left or right-hand daytime driving light is faulty.
Have the system checked. It is recommended you visit an INFINITI retailer for this service.
[Adaptive front lighting sys-
tem Inoperative]The Adaptive Front Lighting System is faulty. The lights remain available without the Adaptive Front Lighting System.
Have the system checked. It is recommended you visit an INFINITI retailer for this service.
[Malfunction See Operator’s
Manual]The exterior lighting is faulty.
Have the system checked. It is recommended you visit an INFINITI retailer for this service.
[Auto Lamp Function inop-
erative]The light sensor is faulty.
Have the system checked. It is recommended you visit an INFINITI retailer for this service.
[Switch Off Lights]The side lights are still switched on when you leave the vehicle. A warning tone also sounds.
Turn the light switch to.
[High beam assist Currently
Unavailable See Operator’s
Manual]High beam assist is deactivated and temporarily inoperative. Possible causes:
•The windshield is dirty in the camera’s field of vision.•Visibility is impaired due to heavy rain, snow or fog.
Clean the windshield.
If the system detects that the camera is fully operational again, the [High beam assist Available Again] message is displayed.
[High beam assist Inopera-
tive]High beam assist is faulty.
Have the system checked. It is recommended you visit an INFINITI retailer for this service.
2-42Instruments and controls