change time INFINITI QX30 2017 Owner's Guide

WARNING
•Never leave children or adults who would
normally require the support of others alone
in your vehicle. Pets should not be left alone
either. They could unknowingly activate
switches or controls and inadvertently be-
come involved in a serious accident and in-
jure themselves. On hot, sunny days, tem-
peratures in a closed vehicle could quickly
become high enough to cause severe or
possibly fatal illness to people or animals.
•Properly secure all cargo to help prevent it
from sliding or shifting. Do not place cargo
higher than the seatbacks. In a sudden stop
or collision, unsecured cargo could cause
personal injury.
•To avoid raising the center of gravity exces-
sively, do not exceed the rated capacity of
the roof rack (if so equipped) and evenly
distribute the load.
EXHAUST GAS (CARBON MONOXIDE)
WARNING
•Do not breathe exhaust gas; it contains
colorless and odorless carbon monoxide.
Carbon monoxide is dangerous. It can cause
unconsciousness or death.
•If you suspect that exhaust fumes are entering
the vehicle, drive with all windows fully open,
and have the vehicle inspected immediately.
•Do not run the engine in closed spaces such
as a garage.
•Do not park the vehicle with the engine
running for an extended period of time.
•Keep the lift gate closed while driving, other-
wise exhaust gas could be drawn into the pas-
senger compartment. If you must drive with
the lift gate open, follow these precautions:
–Open all the windows.
–Turn the air recirculation switch off and
set the fan control to the highest level to
circulate the air.
•If electrical wiring or other cable connec-
tions must pass to a trailer through the seal
ion the lift gate or body, follow the manufac-
turer’s recommendations to prevent carbon
monoxide entry into the vehicle.
•The exhaust system and body should be
inspected by a qualified mechanic when-
ever:
–You suspect that exhaust fumes are en-
tering into the passenger compartment.
–You notice a change in the sound of the
exhaust system.
–You have had an accident involving dam-
age to the exhaust system, underbody,
or rear of the vehicle.
THREE-WAY CATALYST (IF EQUIPPED)
The three-way catalyst is an emission control
device installed in the exhaust system. Exhaust
gas in the three-way catalyst is burned at high
temperatures to help reduce pollutants.
WARNING
•The exhaust gas and the exhaust system
are very hot. Keep people, animals and
flammable materials away from the exhaust
system components.
•Do not stop or park the vehicle over flam-
mable materials such as dry grass, waste-
paper or rags. They may ignite and cause a
fire.
PRECAUTIONS WHEN STARTING AND
DRIVING
5-4Starting and driving

If the vehicle was parked for longer than 20
minutes, the [Tire pressures will be displayed
after driving a few minutes] message is shown.
After a teach-in period, the tire pressure moni-
tor automatically detects new wheels or new
sensors. If a clear allocation of tire pressure to
individual wheels is not possible, the Tire pres-
sure monitor active message is shown instead
of the tire pressure display. The tire pressures
are already being monitored.
If a replacement wheel is fitted, for a few
minutes the system may continue to show the
tire pressure of the wheel that has been re-
moved. If this occurs, note that the value dis-
played for the position where the replacement
wheel is fitted is not the same as the current tire
pressure of the replacement wheel.
Tire Pressure Monitoring System
warning messages
If the tire pressure monitor detects a pressure loss
in one or more tires, a warning message is shown
in the vehicle information display and the yellow
tire pressure monitor warning lamp comes on.
•If the [Please Correct Tire Pressure] (yellow)
message appears in the vehicle information
display, the tire pressure in at least one tire
is too low and must be corrected at the next
opportunity. If the system detects that new
sensors have been fitted (IDs do not match
those stored, and the pressure is not fea-
sible, or is less than 14% under the norm
then the [Please Correct Tire Pressure] mes-
sage will be displayed in white.
•If the [Check Tires] (red) message appears in
the vehicle information display, the tire pres-
sure in one or more tires has dropped sig-
nificantly and the tires must be checked.
•If the [Warning Tire Malfunction] (red) message
appears in the vehicle information display, the
tire pressure in one or more tires has dropped
suddenly and the tires must be checked.
•If the [Tire Press. Sensor(s) Missing] mes-
sage appears in the vehicle information dis-
play, one or more sensors are missing or
cannot be detected. This could be the result
of fitting a replacement wheel/tire.Observe the instructions and safety notes in the
display messages in the vehicle information
display.
If the wheel positions on the vehicle are inter-
changed, the tire pressures may be displayed
for the wrong positions for a short time. After a
few minutes of driving, this is rectified and the
tire pressures are displayed for the correct
positions.
Restarting TPMS
To keep the TPMS functioning properly, the
restart operation must be performed in the
following cases:
•When the tire pressure is adjusted
•When a tire or a wheel is replaced
•When the tires are rotated
When you restart the tire pressure monitor, all
existing warning messages are deleted and the
warning lamps go out. The monitor uses the
currently set tire pressures as the reference
values for monitoring. In most cases, the tire
pressure monitor will automatically detect the
new reference values after you have changed
the tire pressure. However, you can also define
reference values manually as described here.
The tire pressure monitor then monitors the
new tire pressure values.
NSD633
5-8Starting and driving

•The vehicle generally moves or pulls in the
direction of the flat tire.
•Do not rapidly apply the brakes.
•Do not rapidly release the accelerator
pedal.
•Do not rapidly turn the steering wheel.
1. Remain calm and do not overreact.
2. Maintain a firm grip on the steering wheel
with both hands and try to hold a straight
course.
3. When appropriate, slowly release the accel-
erator pedal to gradually slow the vehicle.
4. Gradually steer the vehicle to a safe location
off the road and away from traffic if possible.
5. Lightly apply the brake pedal to gradually
stop the vehicle.
6. Turn on the hazard warning flashers and
contact a roadside emergency service to
change the tire. For additional information,
refer toFlat tirein the6. In case of
emergencysection.
DRINKING ALCOHOL/DRUGS AND
DRIVING
WARNING
Never drive under the influence of alcohol or
drugs. Alcohol in the bloodstream reduces co-
ordination, delays reaction time and impairs
judgement. Driving after drinking alcohol in-
creases the likelihood of being involved in an
accident injuring yourself and others. Addi-
tionally, if you are injured in an accident, alco-
hol can increase the severity of the injury.
INFINITI is committed to safe driving. However,
you must choose not to drive under the influ-
ence of alcohol. Every year thousands of people
are injured or killed in alcohol-related acci-
dents. Although the local laws vary on what is
considered to be legally intoxicated, the fact is
that alcohol affects all people differently and
most people underestimate the effects of alco-
hol.
Remember, drinking and driving don’t mix! And
that is true for drugs, too (over-the-counter,
prescription, and illegal drugs). Don’t drive if
your ability to operate your vehicle is impaired
by alcohol, drugs, or some other physical con-
dition.
DRIVING SAFETY PRECAUTIONS
Your INFINITI is designed for both normal and
off-road use. However, avoid driving in deep
water or mud as your INFINITI is mainly de-
signed for leisure use, unlike a conventional
off-road vehicle.
Remember that 2–wheel drive vehicles are less
capable than all-wheel drive (AWD) models for
rough road driving and extrication when stuck
in deep snow or mud, or the like.
Please observe the following precautions:
WARNING
•Spinning the front wheels on slippery sur-
faces may cause the AWD warning message
to display and the AWD system to automati-
cally switch from the AWD to 2WD mode.
This could reduce the traction. Be especially
careful when towing a trailer. (AWD models)
•Drive carefully when off the road and avoid
dangerous areas. Every person who drives
or rides in this vehicle should be seated
with their seat belt fastened. This will keep
you and your passengers in position when
driving over rough terrain.
Starting and driving5-11

Drive mode switch
The drive mode switch allows you to choose
between drive programs with different driving
characteristics.
Press drive mode switch
1. The selected drive
program appears in the vehicle information
display.
The automatic transmission switches to drive
program E each time the engine is started.
E (Economy): comfortable, economical driving
S (Sport): sporty driving style
M (Manual): manual gear shifting
For more details of the manual drive program
seeManual drive programlater in this section.
Steering wheel gearshift paddles
1Left steering wheel gearshift paddle
(shifts down)
2Right steering wheel gearshift paddle
(shifts up)
In drive program M, you can change gear your-
self using the steering wheel gearshift paddles.
If you pull the left or right steering wheel
gearshift paddle when in automatic drive pro-
gram E or S, the automatic transmission shifts
into drive program M for a limited time. Depend-
ing on which gearshift paddle is pulled, the
automatic transmission immediately shifts into
the next gear down or up.
Automatic drive programs
Drive program E is characterized by the follow-
ing:
•Comfort-oriented engine settings.
•Optimal fuel consumption resulting from the
automatic transmission shifting up sooner.
•The vehicle pulling away more gently in
forward and reverse gears unless the accel-
erator pedal is depressed fully.
•Increased sensitivity. This improves han-
dling on slippery road surfaces, for example.
•The automatic transmission shifting up
sooner. This results in the vehicle being
driven at lower engine speeds and the
wheels being less likely to spin.
Drive program S is characterized by the follow-
ing:
•Sporty engine settings.
•The automatic transmission shifting up
later.
•As a result of the later automatic transmis-
sion shift points, the fuel consumption pos-
sibly being higher.
NSD587NSD584
Starting and driving5-21

Manual drive program
In manual drive program M, you can change
gear yourself by using the steering wheel gear-
shift paddles. For this, the transmission must
be in position D (Drive). The gear currently
selected and engaged is shown in the vehicle
information display
Manual drive program M differs from drive
programs E and S with regard to spontaneity,
responsiveness and smoothness of gear
changes.
Using manual gears
:
3 To use the engine’s braking effect
2 To use the braking effect of the engine on
downhill gradients and for driving on steep
mountain roads, in mountainous terrain or
in arduous conditions.
1 To use the braking effect of the engine on
extremely steep downhill gradients and on
long downhill stretches.Activating the manual drive program
:
•Permanently: Press the drive mode switch
1repeatedly until M appears in the vehicle
information display. Manual drive program M
remains active until drive program E or S is
engaged.
•Temporarily: Pull the right or left steering
wheel gearshift paddle (seeSteering wheel
gearshift paddleslater in this section).
Manual drive program M is temporarily ac-
tive. Depending on which gearshift paddle is
pulled, the automatic transmission immedi-
ately shifts into the next gear down or up.When manual drive program M is activated via
the steering wheel gearshift paddles, the tem-
porarily active manual drive program M will be
deactivated automatically after a limited time, if
the driving situation permits. The automatic
transmission switches to the previously acti-
vated drive program E or S. When driving on
downhill gradients, the temporarily active
manual drive program M will only be deacti-
vated if the accelerator pedal is depressed
while the vehicle is rolling downhill.
Upshifting
:
Pull the right-hand steering wheel gearshift
paddle (seeSteering wheel gearshift paddles
earlier in this section). The automatic transmis-
sion shifts up to the next gear.
In order to prevent engine damage the auto-
matic transmission automatically shifts up if
the maximum engine speed on the currently
engaged gear is reached and you depress the
accelerator pedal.
NSD587
5-22Starting and driving

LDW SYSTEM OPERATION
1Steering wheel mounted controls
2Vehicle information display
ADisplay area
BMenu barThe LDW system operates at speeds of approxi-
mately 40 MPH (60 km/h) and above, when the
lane markings are clear.
If the system detects that the vehicle’s front
wheel has passed over the lane marking, a
warning will be provided. It will warn you by
means of intermittent vibration through the
steering wheel for up to 1.5 seconds and a
visual alert.
NOTE
The LDW system is designed not to warn when
you operate the lane change signal and change
traveling lanes in the direction of the signal.
No warning vibration occurs if you activate the
turn signals. In this event, the warnings are sup-
pressed for a certain period of time.
NSD626
5-30Starting and driving

HOW TO ENABLE/DISABLE THE LDW
SYSTEM
1. Press theorbutton on the
steering wheel
1to select the [DriveAssist]
menu on the Menu bar
B.
2. Press the
orbutton to select
[Lane Departure Warning].
3. Press thebutton on the steering wheel
1. The current selection is displayed.
4. Press theto confirm.
5. Press the
orbutton to set [Off],
[Standard] or [Adaptive].
6. Press thebutton to save the setting.
When the LDW is activated, the vehicle
information display shows the lane mark-ings as bright lines in the assistance graphic
in the display area
A
When [Standard] is selected, no warning vibra-
tion occurs if:
•You have switched on the turn signals. In
this event, the warnings are suppressed for a
certain period of time.
•A driving safety system intervenes, such as
ABS, brake assist system (BAS) or VDC.
When [Adaptive] is selected, no warning vibra-
tion occurs if:
•You have switched on the turn signals. In
this case the warnings are suppressed for a
certain period of time.
•A driving system intervenes, such as ABS,
BAS or VDC.
•You accelerate forcefully.
•You brake forcefully.
•You steer actively, for example, swerve to
avoid an obstacle or change lane quickly.
•You cut the corner on a sharp bend.
The system may detect certain conditions and
warns you accordingly.The warning vibration occurs earlier if:
•You approach the outer lane marking on a
bend.
•The road has very wide lanes, for example, a
freeway.
•The system detects solid lane markings.
The warning vibration occurs later if:
•The road has narrow lanes.
•You cut across a corner on a bend.
LDW SYSTEM LIMITATIONS
WARNING
Listed below are the system limitations for the
LDW system. Failure to operate the vehicle in
accordance with these system limitations
could result in serious injury or death.
•This system is only a warning device to
inform the driver of a potential unintended
lane departure. It will not steer the vehicle
or prevent loss of control. It is the driver’s
responsibility to stay alert, drive safely,
keep the vehicle in the traveling lane, and
be in control of the vehicle at all times.
•The system will not operate at speeds be-
low approximately 40 MPH (60 km/h) or if it
cannot detect lane markers.
NSD599Assistance graphic
Starting and driving5-31

RADAR MAINTENANCE
The two radar sensor unitsAfor the BSW
system are located near the rear bumper. Al-
ways keep the area near the radar sensors
clean.
The radar sensors may be blocked by temporary
ambient conditions such as splashing water,
mist or fog.
The blocked condition may also be caused by
objects such as ice, frost or dirt obstructing the
radar sensors.
Check for and remove objects obstructing the
area around the radar sensors.
Do not attach stickers (including transparent
material), install accessories or apply addi-
tional paint near the radar sensors.Do not strike or damage the area around the
radar sensors. It is recommended you consult
an INFINITI retailer if the area around the radar
sensors is damaged due to a collision.
FCC NOTICE
For USA:
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause harm-
ful interference, and (2) this device must accept
any interference received, including interfer-
ence that may cause undesired operation.
NOTE
Changes or modification not expressly approved
by the party responsible for compliance could
void the user’s authority to operate the equip-
ment.
For Canada:
This device complies with Industry Canada
license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this
device may not cause harmful interference, and
(2) this device must accept any interference re-
ceived, including interference that may cause
undesired operation of the device.Cruise control maintains a constant road speed
for you. It brakes automatically in order to avoid
exceeding the set speed. You must select a
lower gear in good time on long and steep
downhill gradients, especially if the vehicle is
laden or towing a trailer.WARNING
For vehicles with automatic transmission, you
need to have selected manual drive program M
(seeManual drive programearlier in this sec-
tion). By doing so, you will make use of the
braking effect of the engine. This relieves the
load on the brake system and prevents the
brakes from overheating and wearing too
quickly.
Use cruise control only if road and traffic con-
ditions are appropriate for maintaining a steady
speed for a prolonged period. You can set the
cruise control at any road speed above 20 MPH
(30 km/h).
The speed indicated in the speedometer may
differ slightly from the set speed.
NAA1640
CRUISE CONTROL
5-44Starting and driving

System operation
The driver sets the desired vehicle speed based
on the road conditions. The ICC system main-
tains the set vehicle speed, similar to standard
cruise control, as long as no vehicle is detected
in the lane ahead. The ICC system displays the
set speed for 5 seconds after the cruise control
lever is activated.
Vehicle detected ahead
:
When a vehicle is detected in the lane ahead,
the ICC system decelerates the vehicle by con-
trolling the throttle and applying the brakes to
match the speed of a slower vehicle ahead. The
system then controls the vehicle speed based
on the speed of the vehicle ahead to maintain
the driver selected distance.The brake lights of the vehicle come on when
braking is performed by the ICC system. When
the brake operates, a noise may be heard. This
is not a malfunction.
When a vehicle ahead is detected, the vehicle
ahead symbol
1appears in the vehicle infor-
mation display.
Vehicle ahead not detected
:
When a vehicle is no longer detected ahead, the
ICC system gradually accelerates your vehicle to
resume the previously set vehicle speed. The
ICC system then maintains the set speed.
When a vehicle is no longer detected, the
vehicle ahead display turns off
2.If a vehicle ahead appears during acceleration
to the set vehicle speed or any time the ICC
system is in operation, the system controls the
distance to that vehicle.
Changing lanes to pass another
vehicle:
When you changes lane to pass another ve-
hicle, ICC supports the action if:
•The vehicle speed is more than 45 MPH (70
km/h)
•The ICC is maintaining the distance to a
vehicle in front
•The respective turn signal is activated
If these conditions are met, the vehicle will be
accelerated. Acceleration will be interrupted if
changing lanes takes too long or if the distance
between your vehicle and the vehicle in front
becomes too small.
NSD615System set display with vehicle aheadNSD616System set display without vehicle ahead
Starting and driving5-51

For further information on deactivating the ICC
system, seeICC switch (cruise control lever)
earlier in this section
If the ICC system detects that the vehicle in
front is stopping, it brakes your vehicle until it
is stationary (within the braking limitations of
the system).
Once your vehicle is stationary, it remains sta-
tionary and you do not need to depress the brake.
NOTE
•After a short period, the vehicle is secured
by the electric parking brake, thus relieving
the service brake.
•Depending on the specified minimum dis-
tance, your vehicle will come to a standstill
at a sufficient distance behind the vehicle in
front. The specified minimum distance is set
using the control on the cruise control lever.
The electric parking brake secures the vehicle
automatically if the ICC system is activated
when the vehicle is stationary and:
•A system fault occurs.
•The power supply is insufficient.
If a malfunction in the electric parking brake
occurs, then the transmission may also be
shifted into position P (Park) automatically.
How to change the set distance to
the vehicle ahead
The distance to the vehicle ahead can be se-
lected at any time depending on the traffic
conditions.
To increase the distance to the vehicle ahead,
turn the knob
3toward the rear2.Tode-
crease the distance to the vehicle ahead, turn
the knob
3toward the front1.
You can see this distance in the vehicle infor-
mation display.
The distance to the vehicle ahead will change
according to the vehicle speed. The higher the
vehicle speed, the longer the distance.
Approach warning
If your vehicle comes closer to the vehicle
ahead due to rapid deceleration of that vehicle
or if another vehicle cuts in, the system warns
the driver with the chime and distance warning
light. Decelerate by depressing the brake pedal
to maintain a safe vehicle distance if:
•The chime sounds.
•The distance warning light is illuminated.
The warning chime may not sound and the
distance warning light may not illuminate in
some cases when there is a short distance
between vehicles. Some examples are:
•When the vehicles are traveling at the same
speed and the distance between vehicles is
not changing. In this case, the distance
warning light will be on.
•When the vehicle ahead is traveling faster
and the distance between vehicles is increas-
ing.
•When a vehicle cuts in near your vehicle
NSD583A
Starting and driving5-53