window INFINITI QX30 2017 Service Manual

CAUTION
•The TPMS may not function properly when
the wheels are equipped with snow chains
or the wheels are buried in snow.
•Do not place metalized film or any metal
parts (antenna, etc.) on the windows. This
may cause poor reception of the signals
from the tire pressure sensors, and the
TPMS will not function properly.
It is the driver’s responsibility to set the tire
pressure to the recommended cold tire pressure
suitable for the operating situation (see
Wheels and tiresin the8. Do-it-yourself
section). Note that the correct tire pressure for
the current operating situation must first be
taught-in to the tire pressure monitor (see
Restarting TPMSlater in this section).
If there is a substantial loss of pressure, the
warning threshold for the warning message is
aligned to the reference values taught-in. Re-
start the tire pressure monitor after adjusting to
the cold tire pressure. The current pressures are
saved as new reference values. This will ensure
that a warning message will only appear if the
tire pressure drops significantly.
The tire pressure monitor does not warn you of
an incorrectly set tire pressure.TPMS is not able to warn you of a sudden loss
of pressure, e. g. if the tire is penetrated by a
foreign object. In the event of a sudden loss of
pressure, bring the vehicle to a halt by braking
carefully. Avoid abrupt steering maneuvers.
TPMS has a yellow warning lamp in the combi-
nation meter for indicating a pressure loss or
malfunction. Depending on how the warning
lamp flashes or lights up, a tire pressure that is
too low or a malfunction in TPMS is indicated:
•If the warning lamp is lit continuously, the
tire pressure on one or more tires is signifi-
cantly too low. TPMS is not malfunctioning.
•If the warning lamp flashes for around a
minute and then remains lit constantly, the
TPMS is malfunctioning.
In addition to the warning lamp, a message
appears in the vehicle information display. Ob-
serve the information on display messages (see
Safety systemsin the2. Instruments and
controlssection
It may take up to ten minutes for a malfunction
of the tire pressure monitor to be indicated. A
malfunction will be indicated by the tire pres-
sure warning lamp flashing for approximately
one minute and then remaining lit. When the
fault has been rectified, the tire pressure warn-
ing lamp goes out after you have driven for a
few minutes.The tire pressure values indicated by the ve-
hicle information display may differ from those
measured at a filling station using a pressure
gauge. The tire pressures shown by the vehicle
information display are those measured at sea
level. At high altitudes, the tire pressure values
indicated by a pressure gauge are higher than
those shown by the vehicle information display.
In this case, do not reduce the tire pressures.
The operation of the tire pressure monitor can
be affected by interference from radio transmit-
ting equipment (e.g. radio head phones, two-
way radios) that may be being operated in or
near the vehicle.Checking the tire pressure
electronically
1. Make sure that the ignition switch is in the
ON position.
2. Press the
orbutton on the
steering wheel to select the [Serv.] menu.
3. Press the
orbutton to select
[Tire Pressure].
4. Press to confirm.
The current tire pressure for each wheel will
be displayed in the vehicle information dis-
play.
Starting and driving5-7

KEY POSITIONS
OFF (Normal parking position)
0
The ignition key can only be removed when in
this position.
The steering lock can only be locked in this
position.
ACC (Accessories)/1
The engine is turned off without locking the
steering wheel. This position activates electrical
accessories, such as the radio, when the engine
is not running.
ON (Normal operating position)2
This position turns on the ignition system and
electrical accessories.
START3
The engine starter activates and the engine will
start. As soon as the engine has started, release
the key immediately. It will return to the ON
position.NOTE
For vehicles fitted with Idle Stop/Start System:
When the engine is automatically stopped by
the Idle Stop/Start System the ignition switch
can still be operated as usual.
At the end of a journey turn the ignition OFF to
avoid a discharged battery. The Idle Stop/Start
System does not automatically turn ignition off.
•Make sure the area around the vehicle is
clear.
•Check fluid levels such as engine oil, cool-
ant, brake fluid, and windshield-washer fluid
as frequently as possible, or at least when-
ever you refuel.
•Check that all windows and lights are clean.
•Visually inspect tires for their appearance
and condition. Measure and check the tire
pressure for proper inflation.
•Check that all doors are closed.
•Position seat and adjust head restraints/
headrests.
•Adjust the inside and outside rear view
mirrors.
•Fasten your seat belt and ask all passengers
to do likewise.
•Check the operation of the warning lights
when the ignition switch is pushed to the ON
position.
BEFORE STARTING ENGINE
Starting and driving5-15

Illustration 2:If the turn signal is then acti-
vated, the system chimes (twice) and the BSW
indicator light flashes. The BSW indicator light
continues to flash until the detected vehicles
leave the detection zone.
NOTE
•The BSW indicator lights illuminate for a few
seconds when the ignition switch is placed in
the ON position.
•The brightness of the BSW indicator lights is
adjusted automatically depending on the
brightness of the ambient light.
•If a vehicle comes into the detection zone
after the driver activates the turn signal, then
only the BSW indicator light flashes and no
chime sounds. (SeeAnother vehicle ap-
proaching from behindlater in this section.)A chime sounds if the radar sensors have
already detected vehicles when the driver acti-
vates the turn signal.
WARNING
•Do not use the BSW system when towing a
trailer because the system may not function
properly.
•Excessive noise (for example audio system
volume, open vehicle window) will interfere
with the chime sound, and it may not be
heard.
•The radar sensors may not be able to detect
and activate BSW when certain objects are
present such as:
–Pedestrians, bicycles, animals
–Several types of vehicles such as motor-
cycles
–Oncoming vehicles
–Vehicles remaining in the detection
zone when you accelerate from a stop.
–A vehicle merging into an adjacent lane
at a speed approximately the same as
your vehicle.
–A vehicle approaching rapidly from be-
hind.
–A vehicle which your vehicle overtakes
rapidly.
•Severe weather or road spray conditions
may reduce the ability of the radar to detect
other vehicles.
•The radar sensors detection zone is de-
signed based on a standard lane width.
When driving in a wider lane, the radar sen-
sors may not detect vehicles in an adjacent
lane. When driving in a narrow lane, the
radar sensors may detect vehicles driving
two lanes away.
•The radar sensors are designed to ignore
most stationary objects, however objects
such as guardrails, walls, foliage and
parked vehicles may occasionally be de-
tected. This is a normal operating condition.
SSD1031ZIllustration 2
Starting and driving5-37

–Vehicles such as motorcycles, low
height vehicles, or high ground clear-
ance vehicles.
–Oncoming vehicles.
–Vehicles remaining in the detection
zone when you accelerate from a stop.
–A vehicle merging into an adjacent lane
at a speed approximately the same as
your vehicle.
–A vehicle that is too close to your ve-
hicle.
–A vehicle approaching rapidly from be-
hind.
–A vehicle which your vehicle overtakes
rapidly.
•The radar sensors detection zone is de-
signed based on a standard lane width.
When driving in a wider lane, the radar sen-
sors may not detect vehicles in an adjacent
lane. When driving in a narrow lane, the
radar sensors may detect vehicles driving
two lanes away.
•The radar sensors are designed to ignore
most stationary objects, however objects
such as guardrails, walls, foliage and
parked vehicles may occasionally be de-
tected. This is a normal operating condition.
•The following conditions may reduce the
ability of the radar to detect other vehicles:
–Severe weather
–Road spray
–Ice build-up on the vehicle
–Frost build-up on the vehicle
–Dirt build- up on the vehicle
•Do not attach stickers (including transpar-
ent material), install accessories or apply
additional paint near the radar sensors.
These conditions may reduce the ability of
the radar to detect other vehicles.
•Do not use the BSW system when towing a
trailer because the system may not function
properly.
•Excessive noise (e.g. audio system volume,
open vehicle window) will interfere with the
chime sound, and it may not be heard.
•The BSW system may not provide a warning
for vehicles that pass through the detection
zone quickly.
Another vehicle approaching from
behind
Illustration 1: The BSW indicator light illumi-
nates if a vehicle enters the detection zone from
behind in an adjacent lane.
However, if the overtaking vehicle is travelling
much faster than your vehicle, the indicator
light may not illuminate before the detected
vehicle is beside your vehicle. Always use the
side and rear mirrors and turn and look in the
direction your vehicle will move to ensure it is
safe to change lanes.
SSD1026ZIllustration 1 – Approaching from behind
Starting and driving5-39

CAUTION
In certain driving and driving safety systems,
the sensors adjust automatically while a cer-
tain distance is being driven after the vehicle
has been delivered or after repairs. Full system
effectiveness is not reached until the end of
this teach-in process.
Brake pads/linings and rotors that are either
new or have been replaced only achieve opti-
mum braking effect after several hundred
miles of driving. Compensate for the reduced
braking effect by applying greater force to the
brake pedalFollow these easy-to-use Fuel Efficient Driving
Tips to help you achieve the most fuel economy
from your vehicle.
1.Use Smooth Accelerator and Brake Pedal
Application
•Avoid rapid starts and stops.
•Use smooth, gentle accelerator and brake
application whenever possible.
•Maintain constant speed while commut-
ing and coast whenever possible.
2.Maintain Constant Speed
•Look ahead to try and anticipate and
minimize stops.
•Synchronizing your speed with traffic lights
allows you to reduce your number of stops.
•Maintaining a steady speed can minimize
red light stops and improve fuel efficiency.
3.Use Air Conditioning (A/C) at Higher Vehicle
Speeds
•Below 40 MPH (64 km/h), it is more
efficient to open windows to cool the
vehicle due to reduced engine load.
•Above 40 MPH (64 km/h), it is more
efficient to use A/C to cool the vehicle due
to increased aerodynamic drag.
•Recirculating the cool air in the cabin
when the A/C is on reduces cooling load.
4.Drive at Economical Speeds and Distances
•Observing the speed limit and not ex-
ceeding 60 MPH (97 km/h) (where legally
allowed) can improve fuel efficiency due
to reduced aerodynamic drag.
•Maintaining a safe following distance
behind other vehicles reduces unneces-
sary braking.
•Safely monitoring traffic to anticipate
changes in speed permits reduced brak-
ing and smooth acceleration changes.
•Select a gear range suitable to road
conditions.
5.Use Cruise Control
•Using cruise control during highway driv-
ing helps maintain a steady speed.
•Cruise control is particularly effective in
providing fuel savings when driving on
flat terrains.
Utilize a map or navigation system to determine
the best route to save time.
FUEL EFFICIENT DRIVING TIPS
5-82Starting and driving

6.Avoid Idling
•Shutting off your engine when safe for
stops exceeding 30 seconds saves fuel
and reduces emissions.
7.Buy an Automated Pass for Toll Roads
•Automated passes permit drivers to use
special lanes to maintain cruising speed
through the toll and avoid stopping and
starting.
8.Winter Warm Up
•Limit idling time to minimize impact to
fuel economy.
•Vehicles typically need no more than 30
seconds of idling at start-up to effectively
circulate the engine oil before driving.
•Your vehicle will reach its ideal operating
temperature more quickly while driving
versus idling.
9.Keeping your Vehicle Cool
•Park your vehicle in a covered parking
area or in the shade whenever possible.
•When entering a hot vehicle, opening the
windows will help to reduce the inside
temperature faster, resulting in reduced
demand on your A/C system.
•Keep your engine tuned up.
•Follow the recommended scheduled mainte-
nance.
•Keep the tires inflated to the correct pres-
sure. Low tire pressure increases tire wear
and lowers fuel economy.
•Keep all the wheels in correct alignment.
Improper alignment increases tire wear and
lowers fuel economy.
•Use the recommended viscosity engine oil.
For additional information, seeRecom-
mended fluids/lubricants and capacitiesin
the10. Technical informationsection
WARNING
•Do not drive beyond the performance capa-
bility of the tires, even with 4WD engaged.
Accelerating quickly, sharp steering ma-
neuvers or sudden braking may cause loss
of control.
•Always use tires of the same type, size,
brand, construction (bias, bias-belted or ra-
dial), and tread pattern on all four wheels.
•This vehicle is not designed for off-road
(rough road) use. Do not drive on sandy or
muddy roads that tires may get stuck in.
•For 4WD equipped vehicles, do not attempt to
raise two wheels off the ground and shift the
transmission to any drive or reverse position
with the engine running. Doing so may result
in drivetrain damage or unexpected vehicle
movement which could result in serious ve-
hicle damage or personal injury.
•Do not attempt to test a 4WD equipped
vehicle on a 2-wheel dynamometer (such as
the dynamometers used by some states for
emissions testing) or similar equipment
even if the other two wheels are raised off
the ground. Make sure that you inform the
test facility personnel that your vehicle is
equipped with 4WD before it is placed on a
INCREASING FUEL ECONOMY FOUR-WHEEL DRIVE (4WD) (IF EQUIPPED)
Starting and driving5-83

TIRE EQUIPMENT
1. SUMMER tires have a tread designed to
provide superior performance on dry pave-
ment. However, the performance of these
tires will be substantially reduced in snowy
and icy conditions. If you operate your ve-
hicle on snowy or icy roads, INFINITI recom-
mends the use of MUD & SNOW or ALL
SEASON TIRES on all four wheels. It is rec-
ommended that you visit an INFINITI retailer
for the tire type, size, speed rating and
availability information.
2. For additional traction on icy roads, studded
tires may be used. However, some U.S.
states and Canadian provinces prohibit their
use. Check local, state and provincial laws
before installing studded tires.
Skid and traction capabilities of studded snow
tires, on wet or dry surfaces, may be poorer than
that of non-studded snow tires.
3. Tire chains may be used if desired. Make
sure they are the proper size for the tires on
your vehicle and are installed according to
the chain manufacturer’s instructions. Use
chain tensioners when recommended by the
tire chain manufacturer to ensure a tight fit.
Loose end links of the tire chains must be
secured or removed to prevent the possibil-
ity of whipping action damage to the fendersor underbody. In addition, drive at a reduced
speed, otherwise, your vehicle may be dam-
aged and/or vehicle handling and perfor-
mance may be adversely affected.
SPECIAL WINTER EQUIPMENT
It is recommended that the following items be
carried in the vehicle during the winter:
•A scraper and stiff-bristled brush to remove
ice and snow from the windows.
•A sturdy, flat board to be placed under the
jack to give it firm support.
•A shovel to dig the vehicle out of snowdrifts.
•Extra washer fluid to refill the windshield
washer fluid reservoir.
DRIVING ON SNOW OR ICE
WARNING
•Wet ice (32°F, 0°C and freezing rain), very
cold snow or ice can be slick and very hard
to drive on. The vehicle will have much less
traction or “grip” under these conditions.
Try to avoid driving on wet ice until the road
is salted or sanded.
•Whatever the condition, drive with caution.
Accelerate and slow down with care. If ac-
celerating or downshifting too fast, the
drive wheels will lose even more traction.
•Allow more stopping distance under these
conditions. Braking should be started
sooner than on dry pavement.
•Allow greater following distances on slip-
pery roads.
•Watch for slippery spots (glare ice). These
may appear on an otherwise clear road in
shaded areas. If a patch of ice is seen ahead,
brake before reaching it. Try not to brake
while on the ice, and avoid any sudden
steering maneuvers.
•Do not use cruise control on slippery roads.
•Snow can trap dangerous exhaust gas under
your vehicle. Keep snow clear of the exhaust
pipe and from around your vehicle.
5-94Starting and driving

WARNING
•Do not continue to drive if your vehicle over-
heats. Doing so could cause engine damage
or a vehicle fire.
•To avoid the danger of being scalded, never
remove the radiator or coolant reservoir cap
while the engine is hot. When the radiator or
coolant reservoir cap is removed, pressur-
ized hot water will spurt out, possibly caus-
ing serious injury.
•Do not open the hood if steam is coming
out.
If the engine of your vehicle is overheating
(indicated by the engine coolant temperature
gauge) or if you feel a lack of engine power,
detect unusual noise, etc., proceed as follows:
1. Move and park the vehicle safely off the
road and away from traffic.
2. Turn on the hazard warning flasher lights.
3. Apply the parking brake.
4. Press the P (Park) button.
DO NOT STOP THE ENGINE.
5. Open all windows.6. Switch off the air conditioner system (if
equipped).
7. Set the heater or air conditioner tempera-
ture control to maximum “HOT” and fan
speed control to maximum speed.
8. Exit the vehicle.
9. Visually inspect and listen for steam or
coolant escaping from the radiator before
opening the hood.WARNING
If steam or water is coming from the engine,
stand clear to prevent getting burned.
10. Open the hood. For details, seeHoodin
the3. Pre-driving checks and adjustments
section.
11. Visually check if the cooling fan is running.
12. Visually check the radiator and radiator
hoses for leakage.
WARNING
Be careful not to allow your hands, hair, jew-
elry or clothing to come into contact with, or
get caught in, engine belts or the engine cool-
ing fan. The engine cooling fan can start at any
time.
13. After the engine cools down, check the
coolant level in the engine coolant reservoir
with the engine running.Do not open the
radiator cap (if equipped).
14. If the level is low, remove the engine
coolant reservoir cap and add coolant
slowly into the reservoir. After refilling the
reservoir to the MAX level, install the res-
ervoir cap.
15. Close the hood.
Have your vehicle inspected or repaired. It is
recommended you visit an INFINITI retailer.
IF YOUR VEHICLE OVERHEATS
In case of emergency6-13

REMOVING SPOTS
Remove tar and oil spots, industrial dust, in-
sects, and tree sap as quickly as possible from
the paint surface to avoid lasting damage or
staining. Special cleaning products are avail-
able at an INFINITI retailer or any automotive
accessory store.
UNDERBODY
In areas where road salt is used in the winter, it
is necessary to clean the vehicle’s underbody
regularly in order to prevent dirt and salt from
building up and causing the acceleration of
corrosion on the underbody and suspension.
Before the winter and again in the spring, the
underseal must be checked and, if necessary,
re-treated.
GLASS
Use glass cleaner to remove smoke and dust
film from the glass surfaces. It is normal for
glass to become coated with a film after the
vehicle is parked in the hot sun. Glass cleaner
and a soft cloth will easily remove this film.
CAUTION
When cleaning the inside of the windows, do
not use sharp-edged tools, abrasive cleaners
or chlorine-based disinfectant cleaners. They
could damage the electrical conductors, radio
antenna elements or rear window defroster
elements.
WHEELS
•Wash the wheels when washing the vehicle
to maintain their appearance.
•Clean the inner side of the wheels when the
wheel is changed or the underside of the
vehicle is washed.
•Do not use abrasive cleaners when washing
the wheels.
•Inspect wheel rims regularly for dents or
corrosion. This may cause loss of pressure or
damage the tire bead.
•INFINITI recommends that the road wheels
be waxed to protect against road salt in
areas where it is used during winter.
ALUMINUM ALLOY WHEELS
Wash the wheels regularly with a sponge damp-
ened in a mild soap solution, especially during
winter in areas where road salt is used. The salt
residue from road salt could discolor the wheels
if it is not washed off regularly.
CAUTION
Follow the directions below to avoid staining
or discoloring the wheels:
•Do not use a cleaner that uses strong acid or
alkali contents to clean the wheels.
•Do not apply wheel cleaners to the wheels
when they are hot. The wheel temperature
should be the same as ambient tempera-
ture.
•Rinse the wheel to completely remove the
cleaner within 15 minutes after the cleaner
is applied.
CHROME PARTS
Clean all chrome parts regularly with a nonabra-
sive chrome polish to maintain the finish.
Appearance and care7-3

8 Do-it-yourself
Maintenance precautions..................8-2
Engine compartment check locations...........8-3
2.0L Gasoline engine...................8-3
Engine cooling system....................8-3
Checking engine coolant level.............8-4
Changing engine coolant................8-5
Engine oil............................8-5
Checking engine oil level................8-5
Changing engine oil...................8-5
Changing engine oil filter................8-6
Automatic Transmission Fluid (ATF)............8-7
Brake fluid...........................8-7
Window washer fluid.....................8-8
Battery.............................8-9
Accessing Vehicle battery...............8-10
Maintenance free battery................8-10
Models with Idle Stop/Start System.........8-11
Battery replacement...................8-11
Reinitialisation procedure after battery
reconnection.......................8-12
Jump-starting.......................8-12
Drive belt...........................8-12
Spark plugs..........................8-13
Air cleaner filter.......................8-13
Wiper blades.........................8-13Cleaning..........................8-13
Replacing front window wiper blades........8-14
Replacing rear window wiper blade..........8-15
Brakes.............................8-17
Self-adjusting brakes..................8-17
Fuses..............................8-17
Before replacing a fuse.................8-17
Engine compartment...................8-17
Passenger compartment................8-18
Intelligent key battery replacement..........
.8-20
Checking the battery..................8-20
Replacing the battery..................8-20
Lights.............................8-22
Exterior and interior lights...............8-22
Replacement procedures................8-24
Wheels and tires.......................8-27
Tire Pressure.......................8-27
Tire inflation pressure.................8-29
Tire labeling.......................8-30
Types of tires.......................8-31
Tire chains........................8-33
Tire wear and damage.................8-33
Tire rotation.......................8-34
Replacing wheels and tires..............8-34
Wheel balance......................8-36