lock INFINITI QX30 2017 Repair Manual

WARNING
•Do not adjust the steering wheel while driv-
ing. You could lose control of your vehicle
and cause an accident.
•Do not adjust the steering wheel any closer
to you than is necessary for proper steering
operation and comfort. The driver’s air bag
inflates with great force. If you are unre-
strained, leaning forward, sitting sideways
or out of position in any way, you are at
greater risk of injury or death in a crash. You
may also receive serious or fatal injuries
from the air bag if you are up against it when
it inflates. Always sit back against the seat-
back and as far away as practical from the
steering wheel. Always use the seat belts.Release the lock lever
1as illustrated and
adjust the steering wheel to the desired posi-
tion (up or down
2, forwards or backwards
3). Firmly push the lock lever back into posi-
tion to lock the steering wheel in place.
1. To block out glare from the front, swing
down the sun visor
1.
2. To block glare from the side, remove the sun
visor from the center mount and swing the
visor to the side
2.
NPA1481
SIC2872
STEERING WHEELSUN VISORS
3-16Pre-driving checks and adjustments

WARNING
•Objects viewed in the outside mirror on the
passenger side are closer than they appear.
Be careful when moving to the right. Using
only this mirror could cause an accident.
Use the inside mirror or glance over your
shoulder to properly judge distances to
other objects.
•Do not adjust the mirrors while driving. You
could lose control of your vehicle and cause
an accident.
Folding
Manual type (if equipped):
Fold the outside rear-view mirror by pushing it
towards the rear of the vehicle.
Remote control type (if equipped)
:
The exterior rear view mirror remote control
operates when the ignition switch is in the ACC
or ON position.
Briefly press button
1. Both exterior mirrors
fold in or out.
Power folding outside mirrors (if so
equipped)
CAUTION
•Do not touch the mirrors while they are
moving. Your hand may be pinched, and the
mirror may malfunction.
•Do not drive with the mirrors stored. You
will be unable to see behind the vehicle.
The exterior rear-view mirrors automatically un-
fold when the ignition is switched on or when
the vehicle doors are unlocked. Use the [Fold
Mirrors in when Locking] option under the [CON-
VENIENCE] menu of the Vehicle Information
Display to specify that the mirrors are to beautomatically folded and unfolded. The Auto
fold feature can also be switched off. See
Switching the [Fold Mirrors in when Locking]
function on/offin the2. Instruments and
controlssection.
If the [Fold Mirrors in when Locking] option has
been activated in the Vehicle information dis-
play:
•The exterior mirrors fold in automatically as
soon as you lock the vehicle from the out-
side.
•The exterior mirrors fold out again automati-
cally as soon as you unlock the vehicle and
then open the driver’s or front-passenger
door.
Automatic parking positioner (if so
equipped)
The Parking position for the exterior mirror on
the front-passenger side function is only avail-
able if the vehicle is equipped with the Memory
package.
NIC2638
3-18Pre-driving checks and adjustments

The exterior mirror on the front-passenger side
moves back to its original position:
•As soon as you exceed a speed of 15 km/h.
•About ten seconds after you have disen-
gaged reverse gear.
•If you press button1for the exterior mirror
on the driver’s side.
WARNING
•If you use the memory function on the driv-
er’s side while driving, the adjustments
could cause you to lose control of the ve-
hicle. There is a risk of an accident. Only use
the memory function on the driver’s side
while the vehicle is stationary.
Only use the memory function on the driv-
er’s side while the vehicle is stationary.
•If the memory function adjusts the seat, you
and other vehicle occupants-particularly
children-could become trapped. There is a
risk of injury.
While the memory function is making ad-
justments, make sure that no one has any
part of their body within the sweep of the
seat. If someone becomes trapped, immedi-ately release the memory function position
button The adjustment is stopped.
•If children activate the memory function,
they could become trapped, especially if
they are unattended. There is a risk of in-
jury.
When leaving the vehicle, always take the
key with you and lock the vehicle. Never
leave children unattended in the vehicle.
The memory function can be used at any time,
e.g. even when the key isn’t in the ignition lock.
STORING SETTINGS
With the memory function, you can store up to
three different settings.
•Seat and seatback position
•Driver’s side: position of the exterior mirrors
on the driver’s and front-passenger sides.
To store settings:
1. Adjust the seat (seePower seat
adjustmentin the1. Safety — seats, seat
belts and supplemental restraint system
section).
NIC2637
MEMORY FUNCTION (IF EQUIPPED)
3-20Pre-driving checks and adjustments

Clock settings
Clock settings can be changed.
1. Push

Backing up near a projecting object
The predicted course linesAdo not touch the
object in the display. However, the vehicle may
hit the object if it projects over the actual
moving course.
Backing up behind a projecting
object
The positionCis shown further than the
position
Bin the display. However, the posi-
tion
Cis actually at the same distance as theposition
A. The vehicle may hit the object
when backing up to the position
Aif the object
projects over the actual moving course.
HOW TO PARK WITH PREDICTED
COURSE LINES
WARNING
•If the tires are replaced with different sized
tires, the predicted course line may not be
displayed correctly.
•On a snow-covered or slippery road, there
may be a difference between the predicted
course line and the actual course line.
•The displayed lines will appear slightly off
to the right because the rear view camera is
not installed in the rear center of the ve-
hicle.
•If the battery is disconnected or becomes
discharged, the predicted course lines may
be displayed incorrectly. If this occurs,
please perform the following procedures:
–Turn the steering wheel from lock to lock
while the engine is running.
–Drive the vehicle on a straight road for
more than 5 minutes.
SAA1923SAA1980
4-20Display screen, heater and air conditioner, and audio system

Backing up near a projecting object
The predicted course linesAdo not touch the
object in the display. However, the vehicle may
hit the object if it projects over the actual
moving course.
Backing up behind a projecting
object
The positionCis shown farther than the
position
Bin the display. However, the posi-
tion
Cis actually at the same distance as theposition
A. The vehicle may hit the object
when backing up to the position
Aif the object
projects over the actual moving course.
HOW TO PARK WITH PREDICTED
COURSE LINES
WARNING
•If the tires are replaced with different sized
tires, the predicted course lines may not be
displayed correctly.
•On a snow-covered or slippery road, there
may be a difference between the predicted
course lines and the actual course.
•The displayed lines will appear slightly off
to the right because the rear view camera is
not installed in the rear center of the ve-
hicle.
•If the battery is disconnected or becomes
discharged, the predicted course lines may
be displayed incorrectly. If this occurs,
please perform the following procedures:
–Turn the steering wheel from lock to lock
while the engine is running.
–Drive the vehicle on a straight road for
more than 5 minutes.
SAA1923SAA1980
4-30Display screen, heater and air conditioner, and audio system

AIR CONDITIONING SYSTEM
1Sets the temperature
2De-ices/defogs the windshield
3Set the air distribution
4Activates/deactivates air-recirculation
mode
5Sets the airflow
6Activates/deactivates cooling with air
dehumidification
7Switches the rear window defroster on/
off
Operating tips
A number of tips and recommendations for
optimum use of the air-conditioning system are
listed below:
•Switch on the air-conditioning system by
turning control knob
5clockwise to the
desired position (except position0)
•Set the temperature to 70oF (22oC)
•Recommendation for avoiding misted win-
dows at low exterior temperatures or in rain:
switch on the
cooling with dehumidi-
fication function. Set air distribution to
and if possible switch offand. Deactivate air-recirculation mode.
Set airflow control
5to a setting between 3
and 6.
•Recommendation for rapid cooling or heat-
ing of the vehicle interior: briefly set airflow
control
5to a setting between 3 and 6.
•Recommendation for a constant vehicle in-
terior temperature: set airflow control
5to a
setting between 1 and 3.
NAA1644
4-44Display screen, heater and air conditioner, and audio system

•Recommendation for air distribution in win-
ter: select theandsettings.
Recommendation for air distribution in sum-
mer: select the
orandsettings.
•Only use theWindshield demistingfunc-
tion briefly until the windshield is clear again
•Only use air-recirculation mode briefly, e. g
if there are unpleasant outside odors or
when in a tunnel. The windows could other-
wise mist up as no fresh air is drawn into the
vehicle in air-recirculation mode
•If you change the settings of the climate
control system, the climate status display
appears for approximately three seconds at
the bottom of the screen in the central
display (see separate operating instruc-
tions). You will see the current settings of the
various climate control functions.
Switching air-conditioning system
on/off
Make sure the ignition switch is in the ON
position.
To switch on:turn control
5clockwise to the
desired position (except position0).
To switch off:turn control
5counter-clockwise
to position0.
Activating/deactivating the cooling
with air dehumidification function
If you deactivate theCooling with air dehumidi-
ficationfunction, the air inside the vehicle will
not be cooled. The air inside the vehicle will
also not be dehumidified. The windows can mist
up more quickly. Therefore, only deactivate the
Cooling with air dehumidificationfunction
briefly.
TheCooling with air dehumidificationfunction
is only available when the engine is running.
The air inside the vehicle is cooled and dehu-
midified according to the temperature selected.
Condensation may drip from the underside of
the vehicle when cooling mode is active. This is
normal and not a sign that there is a malfunc-
tion.
To activate
:
Press thebutton The indicator lamp in
thebutton lights up.
To deactivate
:
Press thebutton. The indicator lamp in
thebutton goes out. The cooling with air
dehumidification function has a delayed switch-
off feature.Problems with theCooling with air dehumidifi-
cationfunction
:
Problem:The indicator lamp in thebutton flashes three times or remains off. The
cooling with air dehumidification function can-
not be activated.
Cause and solution:The cooling with air dehu-
midification function has been deactivated due
to a malfunction. Have the system checked. It is
recommended you visit an INFINITI retailer for
this service.
Setting the temperature
You can set the temperature for the entire
vehicle. The set temperature is automatically
maintained at a constant level.
To increase or reduce the temperature: turn
control
1counterclockwise or clockwise. Only
change the temperature setting in small incre-
ments. Start at 70
oF (22oC).
Setting the air distribution
Directs the airflow through the demis-
ter ventilators.
Directs the airflow through the center
and side air ventilators.
Directs the airflow through the footwell
air ventilators.
Display screen, heater and air conditioner, and audio system4-45

NOTE
•You can also activate several of the air
distribution settings simultaneously. In order
to do this, press several of the air distribu-
tion buttons. The air is then routed through
different air ventilators.
•Regardless of the air distribution setting,
airflow is always directed through the side
air ventilators. The side air ventilators can
only be closed if the adjusters are turned
clockwise until they engage.
To set air distribution:
1. Make sure the engine is running.
2. Press one or more of the
,,orbuttons. The corresponding indicator
lamp comes on.
Setting the airflow
1. Make sure the ignition switch is in the ON
position.
2. To increase or reduce airflow: turn control
5counterclockwise or clockwise.
Defogging the windshield
You can use this function to de-ice the wind-
shield or to defog the inside of the windshield
and the side windows.NOTE
You should only select theWindshield demist-
ingfunction until the windshield is clear again.
Activating theWindshield demistingfunction
:
Make sure the ignition switch is in the ON
position.
To activate: press the
button The indica-
tor light in thebutton lights up.
The climate control system switches to the
following functions:
•High airflow
•High temperature
•Air distribution to the windshield and front
side windows
•Air-recirculation mode off
NOTE
•TheWindshield demistingfunction auto-
matically sets the blower output to the opti-
mum demisting effect. As a result, the airflow
may increase or decrease automatically after
the
button is pressed.
•You can adjust the blower output manually
while theWindshield demistingfunction is
in operation. Turn airflow control
5counter-
clockwise or clockwise.Deactivating theWindshield demistingfunc-
tion
:
Press thebutton. The indicator lamp in
thebutton goes out. The previous set-
tings are reactivated. Air-recirculation mode
remains deactivated.
or
Turn temperature control
1counterclockwise
or clockwise.
Defogging the windows
Windows misted up on the inside:
1. Activate theCooling with air dehu-
midificationfunction.
2. If the windows continue to mist up, activate
the
Windshield demistingfunction.
NOTE
You should only select this setting until the
windshield is clear again.
Windows misted up on the outside
:
1. Activate the windshield wipers.
2. Set the air distribution to
or.
NOTE
You should only select this setting until the win-
dows are clear again.
4-46Display screen, heater and air conditioner, and audio system

Setting automatic climate control to
automatic mode
Only automatic climate control features the
Control climate control automaticallyfunction.
In automatic mode, the set temperature is
maintained automatically at a constant level
The system automatically regulates the tem-
perature of the dispensed air, the airflow and
the air distribution.
The automatic mode functions optimally when
theCooling with air dehumidificationfunction
is activated. If desired, cooling with air dehu-
midification can be deactivated.
If you deactivate theCooling with air-
dehumidificationfunction, the air inside the
vehicle will not be cooled. The air inside the
vehicle will also not be dehumidified. The win-
dows can mist up more quickly. Therefore, only
deactivate theCooling with air-
dehumidificationfunction briefly.
To set climate control to automatic mode
:
Make sure the ignition switch is in the ON
position.
Set the desired temperature.
To activate: press the
button The indica-
tor lamp in thebutton lights up. Auto-
matic air distribution and airflow are activated.To switch to manual mode: press the
orbutton
or
Press the
orbutton. The indicator
lamp in thebutton goes out. Automatic
air distribution and airflow are deactivated.
Setting the temperature
Different temperatures can be set for the driv-
er’s and front-passenger sides. The set tem-
perature is automatically maintained at a con-
stant level.
Make sure the ignition switch is in the ON
position.
To increase or reduce temperature: turn control
1or9counterclockwise or clockwise. Only
change the temperature setting in small incre-
ments. Start at 70
oF (22oC).
Setting the air distribution
Directs the airflow through the demis-
ter ventilators.
Directs the airflow through the center
and side air ventilators.
Directs the airflow through the footwell
air ventilators.
Directs the airflow through the center
and side air ventilators as well as the
footwell air ventilators.
Directs the airflow through the center
and side air ventilators as well as the
demister ventilators.
Directs the airflow through the footwell
and demister ventilators.
Directs the airflow through the demis-
ter ventilators, the center and side air
ventilators as well as the footwell air
ventilators.
NOTE
Regardless of the air distribution setting, airflow
is always directed through the side air ventila-
tors. The side air ventilators can only be closed if
the adjusters are turned clockwise until they
engage.
To set the air distribution:
1. Make sure the engine is running.
2. Press the
orbutton repeatedly
until the desired symbol appears in the
display.
Setting the airflow
1. Make sure the ignition switch is in the ON
position.
2. To increase or reduce airflow: press the
orbutton.
4-50Display screen, heater and air conditioner, and audio system