oil change INFINITI QX30 2017 Owners Manual

REMOVING SPOTS
Remove tar and oil spots, industrial dust, in-
sects, and tree sap as quickly as possible from
the paint surface to avoid lasting damage or
staining. Special cleaning products are avail-
able at an INFINITI retailer or any automotive
accessory store.
UNDERBODY
In areas where road salt is used in the winter, it
is necessary to clean the vehicle’s underbody
regularly in order to prevent dirt and salt from
building up and causing the acceleration of
corrosion on the underbody and suspension.
Before the winter and again in the spring, the
underseal must be checked and, if necessary,
re-treated.
GLASS
Use glass cleaner to remove smoke and dust
film from the glass surfaces. It is normal for
glass to become coated with a film after the
vehicle is parked in the hot sun. Glass cleaner
and a soft cloth will easily remove this film.
CAUTION
When cleaning the inside of the windows, do
not use sharp-edged tools, abrasive cleaners
or chlorine-based disinfectant cleaners. They
could damage the electrical conductors, radio
antenna elements or rear window defroster
elements.
WHEELS
•Wash the wheels when washing the vehicle
to maintain their appearance.
•Clean the inner side of the wheels when the
wheel is changed or the underside of the
vehicle is washed.
•Do not use abrasive cleaners when washing
the wheels.
•Inspect wheel rims regularly for dents or
corrosion. This may cause loss of pressure or
damage the tire bead.
•INFINITI recommends that the road wheels
be waxed to protect against road salt in
areas where it is used during winter.
ALUMINUM ALLOY WHEELS
Wash the wheels regularly with a sponge damp-
ened in a mild soap solution, especially during
winter in areas where road salt is used. The salt
residue from road salt could discolor the wheels
if it is not washed off regularly.
CAUTION
Follow the directions below to avoid staining
or discoloring the wheels:
•Do not use a cleaner that uses strong acid or
alkali contents to clean the wheels.
•Do not apply wheel cleaners to the wheels
when they are hot. The wheel temperature
should be the same as ambient tempera-
ture.
•Rinse the wheel to completely remove the
cleaner within 15 minutes after the cleaner
is applied.
CHROME PARTS
Clean all chrome parts regularly with a nonabra-
sive chrome polish to maintain the finish.
Appearance and care7-3

CHANGING ENGINE COOLANT
An INFINITI retailer can change the engine cool-
ant.
Improper servicing can result in reduced heater
performance and engine overheating.
WARNING
•To avoid being scalded, never change the
coolant when the engine is hot.
•Never remove the radiator cap when the
engine is hot. Serious burns could be
caused by high pressure fluid escaping from
the radiator.
•Avoid direct skin contact with used coolant.
If skin contact is made, wash thoroughly
with soap or hand cleaner as soon as pos-
sible.
•Keep coolant out of reach of children and
pets.
Engine coolant must be disposed of properly.
Check your local regulations.
CHECKING ENGINE OIL LEVEL
1. Park the vehicle on a level surface and apply
the parking brake.
2. Start the engine and let it idle until it
reaches the normal operating temperature.
3. Turn off the engine. Wait more than 10
minutes for the oil to drain back into the oil
pan.
4. Remove the dipstick
1and wipe it clean.
Reinsert it all the way.
5. Remove the dipstick and check the oil level.
It should be within the range
2and3.
If the oil level is below
3, remove the oil
filler cap and pour the recommended oil into
the opening.Do not overfill
2.It is normal to add some oil between oil mainte-
nance intervals or during the break-in period,
depending on the severity of operating condi-
tions.
CAUTION
The oil level should be checked regularly. Op-
erating the engine with an insufficient amount
of oil can damage the engine, and such dam-
age is not covered by the warranty.
CHANGING ENGINE OIL
WARNING
•Prolonged and repeated contact with used
engine oil may cause skin cancer.
•Try to avoid direct skin contact with used
oil. If skin contact is made, wash thoroughly
with soap or hand cleaner and plenty of wa-
ter as soon as possible.
•Keep used engine oil out of reach of
children.
CAUTION
Be careful not to burn yourself. The engine oil
may be hot.
NDI15962.0L gasoline engine
ENGINE OIL
Do-it-yourself8-5

1. Park the vehicle on a level surface and apply
the parking brake.
2. Start the engine and let it idle until it
reaches the normal operating temperature,
then turn it off.
3. Remove the oil filler cap by turning it
counterclockwise.
4. Remove the engine undershield.
5. Place a large drain pan under the drain plug.
6. Remove the drain plug with a wrench by
turning it counterclockwise and completely
drain the oil. If the oil filter is to be changed,
remove and replace it at this time. For
additional information, refer toChanging
engine oil filterlater in this section.
•Waste oil must be disposed of properly.
•Check your local regulations.
7. Clean and reinstall the drain plug and a new
washer. Securely tighten the drain plug with
a wrench. Do not use excessive force. Drain
plug tightening torque: 22 ft-lb, 30 N•m
8. Refill engine with recommended oil through
the oil filler opening, then install the oil filler
cap securely.
For additional information on drain and refill
capacity, refer toRecommended fluids/
lubricants and capacitiesin the9. Maintenance
and Schedulessection.
The drain and refill capacity depends on the
oil temperature and drain time. Use these
specifications for reference only. Always use
the dipstick to determine when the proper
amount of oil is in the engine.
9. Start the engine. Check for leakage around
the drain plug and oil filter. Correct as
required.
10. Turn the engine off and wait more than 10
minutes. Check the oil level with the dip-
stick. Add engine oil if necessary.
CHANGING ENGINE OIL FILTER
1. Park the vehicle on a level surface and apply
the parking brake.
2. Turn the engine off.
3. Place a large drain pan under the oil filter
1.
4. Loosen the oil filter
1with an oil filter
wrench by turning it counterclockwise. Then
remove the oil filter by turning it by hand.
CAUTION
Be careful not to burn yourself. The engine oil
may be hot.
5. Wipe the engine oil filter sealing surface
with a clean rag.
NDI1622NDI16102.0L gasoline engine
8-6Do-it-yourself

9 Maintenance and Schedules
Maintenance requirements.................9-2
General maintenance...................9-2
Scheduled maintenance.................9-2
Where to go for service.................9-2
General maintenance.....................9-2
Explanation of general maintenance items......9-2
Explanation of general maintenance items........9-5
Emission control system maintenance........9-6
Chassis and body maintenance............9-6
Maintenance schedules...................9-7Additional maintenance items for severe
operating systems....................9-7
Oil change monitor....................9-7
Maintenance service messages.............9-8
Standard maintenance...................9-10
Emission control system maintenance
(For 2.0L turbo gasoline engine)...........9-10
Chassis & body maintenance.............9-12
Maintenance under severe driving conditions.....9-14
Maintenance log.......................9-15

Parking brake*:
Check the parking brake operation regularly.
Also make sure that the vehicle is held securely
on a fairly steep hill when only the parking
brake is applied. If the parking brake needs
adjustment, it is recommended you visit an
INFINITI retailer for this service.
Seats
:
Check seat position controls such as seat ad-
justers, seatback recliner, etc. to ensure they
operate smoothly and that all latches lock
securely in every position. Check that the head
restraints move up and down smoothly and that
the locks (if so equipped) hold securely in all
latched positions.
Seat belts
:
Check that all parts of the seat belt system (for
example, buckles, anchors, adjusters and re-
tractors) operate properly and smoothly, and
are installed securely. Check the belt webbing
for cuts, fraying, wear or damage.
Steering wheel
:
Check for changes in the steering condition,
such as excessive free play, hard steering or
strange noises.Warning lights and chimes
:
Make sure that all warning lights and chimes
are operating properly.
Windshield defroster
:
Check that the air comes out of the defroster
outlets properly and in good quantity when
operating the heater or air conditioner.
Windshield wiper and washer*
:
Check that the wipers and washer operate
properly and that the wipers do not streak.
Under the hood and vehicle
The maintenance items listed here should be
checked periodically (for example, each time
you check the engine oil or refuel).
Battery*
:
Except for maintenance free battery, check the
fluid level in each cell. It should be between the
“UPPER” and “LOWER” lines. Vehicles operated
in high temperatures or under severe condi-
tions require frequent checks of the battery
fluid level.NOTE
Care should be taken to avoid situations that can
lead to potential battery discharge and potential
no-start conditions such as:
1. Installation or extended use of electronic ac-
cessories that consume battery power when
the engine is not running (Phone chargers,
GPS, DVD players, etc.)
2. Vehicle is not driven regularly and/or only
driven short distances.
In these cases, the battery may need to be
charged to maintain battery health.
Brake fluid level*
:
Make sure that the brake fluid level is between
the “MAX” and “MIN” lines on the reservoir.
Coolant level*
:
Check the coolant level when the engine is cold.
Engine drive belt(s)*
:
Make sure that no belt is frayed, worn, cracked
or oily.
Engine oil level*
:
Check the level after parking the vehicle on a
level spot and turning off the engine. Wait more
than 15 minutes for the oil to drain back into the
oil pan.
9-4Maintenance and Schedules

Steering gear and linkage, axle and suspension
parts, drive shaft boots:
Check for damage, looseness, and leakage of
oil or grease. Under severe driving conditions,
inspect more frequently
Tire rotation:
Tires should be rotated every 6,000 miles
(10,000 km) for 2WD, every 3000 miles (5000
km) for 4WD/AWD according to the instructions
underTire rotation*earlier in this section“Ge-
neral maintenance” in this section. When rotat-
ing tires, check for damage and uneven wear.
Replace if necessary.
Transmission fluid/oil, differential oil, transfer
case oil:
Visually inspect for signs of leakage at specified
intervals.To ensure smooth, trouble-free, safe and eco-
nomical driving, INFINITI provides two mainte-
nance schedules that may be used, depending
upon the conditions in which you usually drive.
These schedules contain both distance and
time intervals, up to 120,000 miles (192,000
km)/144 months. For most people, the odom-
eter reading will indicate when service is
needed. However, if you drive very little, your
vehicle should be serviced at the regular time
intervals shown in the schedule.
After 120,000 miles (192,000 km)/144 months,
continue maintenance at the same mileage/time
intervals.
ADDITIONAL MAINTENANCE ITEMS
FOR SEVERE OPERATING SYSTEMS
Additional maintenance items for severe oper-
ating conditions; should be performed on ve-
hicles that are driven under especially demand-
ing conditions. Additional maintenance items
should be performed if you primarily operate
your vehicle under the following conditions:
•Repeated short trips of less than 5 miles in
normal temperatures or less than 10 miles in
freezing temperatures.
•Stop-and-go traffic in hot weather or low
speed driving for long distances.
•Driving in dusty conditions or on rough,
muddy or salt-spread roads.
•Towing a trailer, or using a camper or car-top
carrier.
OIL CHANGE MONITOR
This vehicle is equipped with oil change moni-
tor. It calculates engine oil and filter change
interval base on driving conditions. Driving in
severe conditions will shorten the engine oil
and filter change interval. When the Engine Oil
– Service Due Now warning appears in the
vehicle information display, the engine oil and
filter need to be replaced.
NOTE
For vehicles operated in Canada, both standard
and severe maintenance items should be per-
formed at every interval.
MAINTENANCE SCHEDULES
Maintenance and Schedules9-7

•For frequent operation in mountainous ter-
rain or on poor road surfaces
•If the engine is often left idling for long
periods
In these or similar operating conditions, have,
for example, the air filter, engine oil and oil
filter changed more frequently. The tires must
be checked more frequently if the vehicle is
operated under increased loads. Further infor-
mation can be obtained at an INFINITI retailer.
Maintenance and Schedules9-9

The following are approximate capacities. The actual refill quantities may be slightly different. When refilling, follow the procedures instructedinthe
“8. Maintenance and do-it-yourself” section to determine the proper refill capacity.
Fluid types Capacity (Approximate) Recommended Fluids and Lubricants
US measure Imp Measure Liter
Fuel tank 13.2 gal
(4WD: 14.8 gal11 gal
(4WD: 12.3 gal)50 L
(4WD: 56 L)
–SeeFuel recommendationlater in this section.
Engine oil (*) The approximate capacities listed are for refilling during an engine oil change. *: For
additional information, seeChanging engine oilin the8. Do-it-yourselfsection.
2.0L gasoline engine:
–Genuine INFINITI engine oil, Viscosity SAE 0W-30
For additional information, seeEngine oil and oil filter recommendationslater in this
section. Drain and refill
With oil filter change 6 qt 5 qt 5.6 L
Cooling system
with Reservoir8.1 qt 6.7 qt 7.6
–Genuine INFINITI Engine Coolant or equivalent in its quality
BASF Glysantin® G40®
–Use Genuine INFINITI Engine Coolant, or equivalent in its quality, in order to avoid
possible aluminum corrosion within the engine cooling system caused by the use
of non-genuine engine coolant.Note that any repairs for incidents with the engine
cooling system while using non-genuine engine coolant may not be covered by the
warranty even if such incidents occurred during the warranty period.
Automatic Transmission Fluid
(ATF)6.6 qt 5.5 qt 6.21 L Shell DCT-M1
Brake fluid Refill to the proper fluid level according to the
instructions in the “8. Maintenance and do-it-
yourself” section.
–Genuine INFINITI brake fluid. DOT 4+ or equivalent.–Never mix different types of fluids.
Differential gear oil 0.8 qt 0.65 qt 0.74 L
–Castrol BOT 355 75W-85
Multi-purpose grease — — —
–NLGI No. 2 (Lithium soap base)
Air conditioner system refrigerant———–HFC-134a
Air conditioner system lubricant———–INFINITI A/C System Oil Type S or equivalent
RECOMMENDED FLUIDS/LUBRICANTS AND
CAPACITIES
10-2Technical information

level roads, it is recommended you have an
INFINITI retailer correct the condition. Failure to
correct the condition is misuse of the vehicle, for
which INFINITI is not responsible.
Incorrect ignition timing will result in knocking,
after-run and/or overheating. This in turn may
cause excessive fuel consumption or damage to
the engine. If any of the above symptoms are
encountered, have your vehicle checked. It is
recommended you visit an INFINITI retailer.
However, now and then you may notice light
spark knock for a short time while accelerating
or driving up hills. This is no cause for concern,
because you get the greatest fuel benefit when
there is light spark knock for a short time under
heavy engine load.
1API certification mark
2API service symbol
ENGINE OIL AND OIL FILTER
RECOMMENDATIONS
Selecting the correct oil
It is essential to choose the correct grade,
quality, and viscosity engine oil to ensure sat-
isfactory engine life and performance. For addi-
tional information, refer toRecommended
fluids/lubricants and capacitiesearlier in this
section. INFINITI recommends the use of an
energy conserving oil in order to improve fuel
economy.
Select only engine oils that meet the American
Petroleum Institute (API) certification or Interna-
tional Lubricant Standardization and ApprovalCommittee (ILSAC) certification and SAE viscos-
ity standard. These oils have the API certifica-
tion mark on the front of the container. Oils
which do not have the specified quality label
should not be used as they could cause engine
damage.
Oil additives
INFINITI does not recommend the use of oil
additives. The use of an oil additive is not
necessary when the proper oil type is used and
maintenance intervals are followed.
Oil which may contain foreign matter or has
been previously used should not be used.
Oil viscosity
The engine oil viscosity or thickness changes
with temperature. Because of this, it is impor-
tant that the engine oil viscosity be selected
based on the temperatures at which the vehicle
will be operated before the next oil change.
Choosing an oil viscosity other than that recom-
mended could cause serious engine damage.
Selecting the correct oil filter
Your new vehicle is equipped with a high—
quality genuine INFINITI oil filter. When replac-
ing, it is recommended you use the genuine oil
filter or its equivalent for the reason described
in “Change intervals”.
NTI326
Technical information10-5

Change intervals
The oil and oil filter change intervals for your
engine are based on the use of the specified
quality oils and filters. Using engine oil and
filters that are not of the specified quality, or
exceeding recommended oil and filter change
intervals could reduce engine life. Damage to
engines caused by improper maintenance or
use of incorrect oil and filter quality and/or
viscosity is not covered by the new INFINITI New
Vehicle Limited Warranty.
Your engine was filled with a high quality
engine oil when it was built. You do not have to
change the oil before the first recommended
change interval. Oil and filter change intervals
depend upon how you use your vehicle.
Operation under the following conditions may
require more frequent oil and filter changes:
•Repeated short distance driving at cold
outside temperatures
•Driving in dusty conditions
•Extensive idling
•Stop and go “rush hour” traffic
Refer to the “INFINITI Service and Maintenance
Guide” for the maintenance schedule.
AIR CONDITIONER SYSTEM
REFRIGERANT AND OIL
RECOMMENDATIONS
The air conditioner system of your vehicle must
be charged with the refrigerant HFC-134a and
the lubricant INFINITI A/C System Oil Type S or
the exact equivalents.
CAUTION
The use of any other refrigerant or oil may
cause severe damage to the air conditioning
system and will require the replacement of all
air conditioner system components.
The refrigerant HFC-134a in your vehicle will not
harm the Earth’s ozone layer. However, it may
contribute in a small part to the global warming
effect.
Certain government regulations require the re-
covery and recycling of any refrigerant during
automotive air conditioner system service. An
INFINITI retailer has the trained technicians and
equipment needed to recover and recycle your
air conditioner system refrigerant.
It is recommended that you visit an INFINITI
retailer when servicing your air conditioner sys-
tem.
10-6Technical information