INFINITI QX30 2018 Owner's Manual

4. When the rear of the vehicle enters the
parking space
C, maneuver the steering
wheel to make the vehicle width guide
lines
Dparallel to the parking spaceC.
5. When the vehicle is parked in the space
completely, press the P (Park) button and
apply the parking brake.
HOW TO SWITCH THE DISPLAY
The view on the Around View® Monitor
screen can be switched by pressing the
button or by changing the shift
lever position.
Press thebutton:
When thebutton is pushed while
a screen other than a camera screen is dis-
played, the Around View® Monitor operates
and the front view and bird's-eye view are
displayed. Push thebutton to
switch the display to the front view and
front-side view screen.
ADJUSTING THE SCREEN
1. Push the

A[Settings] key
B

•The cameras are installed on the front
grille, the outside mirrors and above the
rear license plate. Do not put anything
on the cameras.
•When washing the vehicle with high-
pressure water, be sure not to spray it
around the cameras. Otherwise, water
may enter the camera unit causing wa-
ter condensation on the lens, a malfunc-
tion, fire or an electric shock.
•Do not strike the cameras. They are pre-
cision instruments. Doing so could cause
a malfunction or cause damage resulting
in a fire or an electric shock.
The following are operating limitations and
do not represent a system malfunction:
•There may be a delay when switching be-
tween views.
•When the temperature is extremely high or
low, the screen may not display objects
clearly.
•When strong light is directly shines on the
camera, objects may not be displayed
clearly.
•The screen may flicker under fluorescent
light.
•The colors of objects on the Around
View® Monitor may differ somewhat
from the actual color of objects.
•Objects on the monitor may not be clear
and the color of the object may differ in a
dark environment.
•There may be differences in sharpness be-
tween each camera view of the bird’s-eye
view.
•Do not use wax on the camera lens. Wipe
off any wax with a clean cloth that has
been dampened with a diluted mild clean-
ing agent, then wipe with a dry cloth.
There are some areas where the system will not
show objects and the system does not warn of
moving objects. When in the front or the rear
view display, an object below the bumper or on
the ground may not be viewed
1. When in the
bird's-eye view, a tall object near the seam
3of the camera viewing areas will not appear
in the monitor
2.
NAA1639
Display screen, heater and air conditioner, and audio system4-21

System temporarily unavailable
When the [!] icon is displayed on the screen,
there are abnormal conditions in the Around
View® Monitor. This will not hinder normal
driving operation but the system should be
inspected. It is recommended you visit an
INFINITI retailer for this service.When the [X] icon is displayed on the screen,
the camera image may be receiving tempo-
rary electronic disturbances from surround-
ing devices. This will not hinder normal driving
operation but the system should be in-
spected. It is recommended you visit an
INFINITI retailer for this service.
SYSTEM MAINTENANCE
CAUTION
•Do not use alcohol, benzine or thinner to
clean the camera. This will cause discol-
oration. To clean the camera, wipe with
a cloth dampened with diluted mild
cleaning agent and then wipe with a dry
cloth.
•Do not damage the camera as the moni-
tor screen may be adversely affected.
If dirt, rain or snow accumulates on any of the
cameras, the Around View® Monitor may
not display objects clearly. Clean the cameras
by wiping with a cloth dampened with a di-
luted mild cleaning agent and then wiping
with a dry cloth.
NAA1779NAA1780NAA1638
4-22Display screen, heater and air conditioner, and audio system

A[Settings] key
B

AAround View Monitor display
BINFINITI controller
C

MOD SYSTEM OPERATION
The MOD system will activate automatically
under the following conditions:
•When the shift lever is in the R (Reverse)
position. When the shift lever is moved to
the R (Reverse) position to activate the
Around View Monitor and MOD, the icons
and the messages may not be displayed
immediately.
•When thebutton is pressed
to switch from a different screen to the
camera view on the display.
•When vehicle speed decreases below ap-
proximately 5 MPH (8 km/h).
•When the ignition switch is placed in the
OFF position and then back to the ON
position.
NOTE
•The MOD system does not detect moving
objects in the front-side view. The MOD
icon is not displayed on the screen when in
this view.
•While the parking sensor warning tone is
sounding, the MOD system does not chime.
The MOD system operates in the following
conditions when the camera view is dis-
played:
When the shift lever is in the R (Reverse)
position and the vehicle speed is approxi-
mately 5 MPH (8 km/h ) or less, the MOD
system detects moving objects in the camera
view. The MOD system will not operate if the
lift gate is open.
When the MOD system detects moving ob-
jects near the vehicle, a chime will be heard
and a yellow frame
1will be displayed on
the monitor.
While the MOD system continues to detect
moving objects, the yellow frame continues
to be displayed.
The yellow frame
1is displayed on each
view in the rear view modes.
A blueicon is displayed in the view
where the MOD system is operative. A gray
MOD icon is displayed in the view where the
MOD system is not operative.
NAA1781
Bird's-eye view
NAA1782
Front view / rear view
Display screen, heater and air conditioner, and audio system4-25

A[Settings] key
B

–When strong light such as another
vehicle’s headlight or sunlight is pres-
ent.
–When camera orientation is not in its
usual position, such as when mirror is
folded.
–When there is dirt, water drops or
snow on the camera lens.
–When the position of the moving ob-
jects in the display is not changed.
•The MOD system might detect some-
thing like flowing water droplets on the
camera lens, white smoke from the muf-
fler, moving shadows, etc.
•The MOD system may not function
properly depending on the speed, direc-
tion, distance or shape of the moving
objects.
•If your vehicle sustains damage to the
parts where the camera is installed,
leaving it misaligned or bent, the sensing
zone may be altered and the MOD sys-
tem may not detect objects properly.
•When the temperature is extremely high
or low, the screen may not display ob-
jects clearly. This is not a malfunction.
MOD MALFUNCTION
The blue MOD icon will change to orange if
one of the following has occurred
•When the system is malfunctioning.
•When the component temperature
reaches a high level (icon will blink).
If the icon light continues to illuminate or-
ange, have the MOD system checked. It is
recommended you visit an INFINITI retailer
for this service.
SYSTEM MAINTENANCE
CAUTION
•Do not use alcohol, benzine or thinner to
clean the cameras. This will cause discol-
oration. To clean the cameras, wipe with
a cloth dampened with diluted mild
cleaning agent and then wipe with a dry
cloth.
•Do not damage the cameras as the moni-
tor screen may be adversely affected.
If dirt, rain or snow accumulates on any of the
cameras
1, the MOD system may not oper-
ate properly. Clean the cameras by wiping
with a cloth dampened with a diluted mild
cleaning agent and then wiping with a dry
cloth.
NAA1689
Display screen, heater and air conditioner, and audio system4-27

CENTER VENTILATORS
Open/close the ventilators by turning the
control wheel.
Adjust the air flow direction of the ventilators
by moving the center knob (up/down, left/
right) until the desired position is achieved.
SIDE VENTILATORS
Open/close the ventilators by turning the
control wheel.
Adjust the air flow direction of the ventilators
by moving the center knob (up/down, left/
right) until the desired position is achieved.
REAR VENTILATORS
(IF EQUIPPED)
Open/close the ventilators by turning the
control wheel.
Adjust the air flow direction of the ventilators
by moving the center knob (up/down, left/
right) until the desired position is achieved.
NAA1636
Center
NAA1637
Side
NAA1635
Rear
VENTILATORS
4-28Display screen, heater and air conditioner, and audio system