automatic transmission INFINITI QX30 2018 Owner's Guide

Parking tips:
•The way your vehicle is positioned in the
parking space after parking is dependent
on various factors. These include the posi-
tion and shape of the vehicles parked in
front and behind it and the conditions of
the location. It may be the case that IPA
guides you too far into a parking space, or
not far enough into it. In some cases, it
may also lead you across or onto the curb.
If necessary you should cancel the parking
procedure with IPA.
•During the parking maneuver, the system
will indicate when you should shift to R
(Reverse) or D (Drive). However, you can
freely choose to shift gear whenever you
feel you need to. Should the transmission
change take place too early, the parking
procedure will be canceled. A sensible
parking position can no longer be achieved
from this position.
EXITING A PARKING SPACE
In order that IPA can support when exiting
the parking space:
•You need to have parked using IPA.
•The border of the parking space must be
high enough at the front and the rear.
A curb stone is too small, for example.
•The border of the parking space must not
be too wide, as the position of the vehicle
must not exceed an angle of 45 degrees to
the starting position as it is manoeuvred
into the parking space.
•A total front and back maneuvering dis-
tance of at least 1.0 m must be available.
IPA can only assist you with exiting a parking
space if you have parked the vehicle parallel
to the direction of travel using IPA.
WARNING
•IPA is only an aid. It is not a substitute
for your attention to the immediate sur-
roundings. The responsibility for safe
maneuvering and parking remains with
you.
•Make sure that no persons, animals or
objects are in the maneuvering range.
•When the sonar function is deactivated,
IPA is also unavailable.
•While parking or pulling out of a parking
space, the vehicle swings out and can
drive onto areas of the oncoming lane.
This could cause you to collide with
other road users. There is a risk of an
accident.
•Pay attention to other road users. Stop
the vehicle if necessary or cancel the IPA
parking procedure.
1. Start the engine.
2. Release the electric parking brake.
3. Switch on the turn signal in the direction
you are pulling away.
4.Vehicles with automatic transmission:
shift the transmission to position D or R
The [Start Park Assist? Yes: OK No:]
message appears in the vehicle informa-
tion display.
5. To cancel the procedure: press the
button on the steering wheel or pull away
or
6. To exit a parking space using IPA: press
thebutton on the steering wheel
The Park Assist [Observe surroundings]
message appears in the display.
7. Release the steering wheel.
8. Pull away, being ready to brake at all
times Do not exceed a maximum speed of
approximately 5 MPH (10 km/h) when
exiting a parking space. Otherwise, IPA
will be canceled.
5-74Starting and driving

WARNING
While parking or pulling out of a parking
space, the vehicle swings out and can drive
onto areas of the oncoming lane. This could
cause you to collide with other road users.
There is a risk of an accident.
9. Depending on the message or as required,
shift the transmission to position D or R.
IPA immediately steers in the other direc-
tion. The [Observe surroundings] mes-
sage appears in the display.
NOTE
You will achieve the best results by wait-
ing for the steering procedure to com-
plete before pulling away.
If you back up after activation, the steer-
ing wheel is moved to the straight-ahead
position.
10. Drive forward and back up as prompted
by the IPA and sonar function warning
displays, several times if necessary.Once you have exited the parking space com-
pletely, the steering wheel is moved to the
straight-ahead position. You hear a tone and
the [Park Assist switched off] message ap-
pears in the display. You will then have to
steer and merge into traffic on your own. The
sonar function is still available. You can take
over the steering before the vehicle has ex-
ited the parking space completely. This is use-
ful, for example when you recognize that it is
already possible to pull out of the parking
space.
CANCELING IPA
Stop the movement of the steering wheel or
steer yourself. IPA will be immediately can-
celed. The [Park Assist canceled] message
appears in the vehicle information display.
or
Press the sonar function OFF switch. The
sonar function is switched off and IPA is
immediately canceled The [Park Assist can-
celed] message appears in the vehicle infor-
mation display.IPA is canceled automatically if:
•The electric parking brake is applied
•Parking using IPA is no longer possible
•You are driving faster than 5 MPH (10 km/h)
•A wheel spins and VDC intervenes or fails.
Thewarning light lights up in the
combination meter.
A warning tone sounds. The parking symbol
disappears and the vehicle information dis-
play shows the [Park Assist canceled] mes-
sage.
When IPA is canceled, you must steer again
yourself.
Starting and driving5-75

ARearView/Around View monitor display
BINFINITI controller
C

1. Firmly apply the parking brake.
2. Press the P (Park) button.
3. To help prevent the vehicle from moving
into traffic when parked on an incline, it is
a good practice to turn the wheels as
illustrated.
HEADED DOWNHILL WITH CURB
1
Turn the wheels into the curb and move
the vehicle forward until the curb side
wheel gently touches the curb. Then apply
the parking brake.
HEADED UPHILL WITH CURB
2
Turn the wheels away from the curb and
allow the vehicle to move back until the
curb side wheel gently touches the curb.
Then apply the parking brake.HEADED UPHILL OR DOWNHILL,
WITHOUT CURB
3
Turn the wheels toward the side of the
road so the vehicle will move away from
the center of the road if the vehicle moves.
Then apply the parking brake.
4.
Put the ignition switch in the OFF position.
SWITCHING OFF THE ENGINE
WARNING
The automatic transmission switches to
position N (Neutral) when you switch off
the engine. The vehicle may roll away.
There is a risk of an accident.
After switching off the engine, always
switch to position P (Park). Prevent the
parked vehicle from rolling away by apply-
ing the parking brake.
Procedure
1. Apply the electric parking brake.
2. Shift the transmission to position P (Park).
3.With the key:turn the key to the position
OFF in the ignition switch and remove it
The immobilizer is activated.
If you switch the engine off with the trans-
mission in position R (Reverse) or D (Drive),
the automatic transmission shifts to N (Neu-
tral) automatically.
With the key: if you then open the driver's
door or the front-passenger door or remove
the key from the ignition, the automatic
transmission shifts to P (Park) automatically.
If you want the automatic transmission to
remain in neutral N (Neutral), e.g. when hav-
ing the vehicle cleaned in an automatic car
wash with a towing system:
With the key:
1. Switch the ignition on.
2. Depress the brake pedal and keep it de-
pressed.
3. Shift to N (Neutral).
SSD0488Z
5-88Starting and driving

•After a short time, hill start assist will no
longer brake your vehicle and it could
roll away There is a risk of an accident
and injury. Therefore, quickly move your
foot from the brake pedal to the accel-
erator pedal. Never leave the vehicle
when it is held by hill start assist.
Hill start assist helps you when pulling away
forwards or in reverse on an uphill gradient. It
holds the vehicle for a short time after you
have removed your foot from the brake
pedal. This gives you enough time to move
your foot from the brake pedal to the accel-
erator pedal and depress it before the vehicle
begins to roll.
Hill start assist is not active if
•You are pulling away on a level road or a
downhill gradient.
•On vehicles with automatic transmission,
the transmission is in position N.
•The electric parking brake is applied.
•VDC is malfunctioning.
FREEING A FROZEN DOOR LOCK
To prevent a door lock from freezing, apply
deicer through the key hole. If the lock be-
comes frozen, heat the key before inserting it
into the key hole, or use the INFINITI Intelli-
gent Key.
ANTIFREEZE
In the winter when it is anticipated that the
temperature will drop below 32°F (0°C),
check the antifreeze to assure proper winter
protection. For additional information, see
"Engine cooling system".
BATTERY
If the battery is not fully charged during ex-
tremely cold weather conditions, the battery
fluid may freeze and damage the battery. To
maintain maximum efficiency, the battery
should be checked regularly. For details, see
"Battery" of this manual.
DRAINING OF ENGINE COOLANT
If the vehicle is to be left outside without
antifreeze, drain the cooling system, including
the engine block. Refill before operating the
vehicle. For details, see "Changing engine
coolant" of this manual.
TIRE EQUIPMENT
1. SUMMER tires have a tread designed to
provide superior performance on dry
pavement. However, the performance of
these tires will be substantially reduced in
snowy and icy conditions. If you operate
your vehicle on snowy or icy roads,
INFINITI recommends the use of MUD &
SNOW or ALL SEASON TIRES on all four
wheels. It is recommended that you visit
an INFINITI retailer for the tire type, size,
speed rating and availability information.
2. For additional traction on icy roads, stud-
ded tires may be used. However, some
U.S. states and Canadian provinces pro-
hibit their use. Check local, state and pro-
vincial laws before installing studded tires.
Skid and traction capabilities of studded
snow tires, on wet or dry surfaces, may be
poorer than that of non-studded snow tires.
COLD WEATHER DRIVING
5-96Starting and driving

•Be sure that the jumper cables do not
touch moving parts in the engine com-
partment and that the cable clamps do
not contact any other metal.
9. Start the engine of the other vehicle
Aand let it run for a few minutes. Keep the
engine speed at about 2,000 rpm.
10. Start the engine of your vehicle
Bin the
normal way.
CAUTION
Do not keep the starter motor engaged for
more than 10 seconds. If the engine does
not start right away, place the ignition
switch in the OFF position and wait 10 sec-
onds before trying again.
11. After starting the engine of your vehicle,
carefully disconnect the negative lead
and then the positive lead (
4→3→2→1).
12.
Remove and dispose of the cloth that was
used to cover the ventilator holes as it may
be contaminated with corrosive acid.
13. Install the ventilator caps (if equipped).
14. Close the hood.NOTE
For models which incorporate the Idle Stop/
Start System:
•Ensure that the battery fitted is the special
battery that is enhanced with regard to the
charge-discharge capacity and life perfor-
mance. Avoid using any other battery for
the Idle Stop/Start System, as this may
cause early deterioration of the battery or
a malfunction of the Idle Stop/Start Sys-
tem. It is recommended that a Genuine
INFINITI battery is fitted. For more infor-
mation, it is recommended you contact an
INFINITI retailer.
•If the battery terminal is disconnected (for
battery replacement, etc.) and then recon-
nected, there may be some delay before
the Idle top/Start System reactivates.Do not attempt to start the engine by pushing
the vehicle.
CAUTION
•Automatic Transmission (AT) model
cannot be push-started or tow-started.
Attempting to do so may cause damage
to the transmission.
•Three-way catalyst equipped models
should not be started by pushing. At-
tempting to do so may cause damage to
the three-way catalyst.
•Never try to start the vehicle by towing
it; when the engine starts, the forward
surge could cause the vehicle to collide
with the tow vehicle.
PUSH STARTING
6-12In case of emergency

Two-Wheel Drive (FWD) models
CAUTION
NEVER tow automatic transmission (DCT)
models with the front wheels on the
ground or with all four wheels on the
ground (forwards or backwards), as this
may cause serious and expensive damage
to the transmission. If it is necessary to tow
the vehicle with the rear wheels raised, al-
ways use towing dollies under the front
wheels.
Four-Wheel Drive (4WD) models
INFINITI recommends that towing dollies be
used under the front or rear wheels when
towing your vehicle or the vehicle be placed
on a flatbed tow truck as illustrated.
CAUTION
Never tow 4WD models with any of the
wheels on the ground. Doing so will cause
serious and expensive damage to the
drivetrain.
Vehicle recovery (freeing a stuck
vehicle)
WARNING
To avoid vehicle damage, serious personal
injury or death when recovering a stuck ve-
hicle:
•Contact a professional towing service to
recover the vehicle if you have any ques-
tions regarding the recovery procedure.
•Tow chains or cables must be attached
only to main structural members of the
vehicle.
•Do not use the vehicle tie downs to tow
or free a stuck vehicle.
•Only use devices specifically designed
for vehicle recovery and follow the
manufacturer's instructions.
•Always pull the recovery device straight
out from the front of the vehicle. Never
pull at an angle.
•Route recovery devices so they do not
touch any part of the vehicle except the
attachment point.
NCE450
4WD models
In case of emergency6-15

•On vehicles with a push button ignition
switch: you must remove the start/stop
button and use the key (see " Push-
button ignition switch (if equipped)").
Otherwise the automatic transmission
may shift to position P (Park) when the
driver's or front passenger door are
opened, which could lead to damage to
the transmission.
If your vehicle is stuck in sand, snow, mud,
etc., use a tow strap or other device designed
specifically for vehicle recovery. Always fol-
low the manufacturer’s instructions for the
recovery device.
Rocking a stuck vehicle
WARNING
•To avoid potential injury, stand clear of
a stuck vehicle.
•Do not spin your tires at high speed. This
could cause them to explode and result
in serious injury. Parts of your vehicle
could also overheat and be damaged.If your vehicle is stuck in sand, snow, mud,
etc., use the following procedure:
1. Turn off the Vehicle Dynamic Control
(VDC) system.
2. Make sure the area in front and behind the
vehicle is clear of obstructions.
3. Turn the steering wheel right and left to
clear an area around the front tires.
4. Slowly rock the vehicle forward and back-
ward.
•Shift back and forth between R (Reverse)
and D (Drive).
•Apply the accelerator as little as possible
to maintain the rocking motion.
•Release the accelerator pedal before shift-
ing between R (Reverse) and D (Drive).
•Do not spin the tires above 35 MPH
(55 km/h).
5. If the vehicle cannot be freed after a few
tries, contact a professional towing ser-
vice to remove the vehicle.
6-16In case of emergency

8 Do-it-yourself
Maintenance precautions.................8-2
Engine compartment check locations.........8-3
2.0L Gasoline engine.................8-3
Engine cooling system...................8-3
Checking engine coolant level............8-4
Changing engine coolant...............8-4
Engine oil...........................8-5
Checking engine oil level...............8-5
Changing engine oil..................8-5
Changing engine oil filter...............8-6
Automatic Transmission Fluid (ATF)..........8-7
Brake fluid..........................8-7
Window washer fluid...................8-8
Battery............................8-9
Accessing Vehicle battery...............8-9
Maintenance free battery..............8-10
Models with Idle Stop/Start System.......8-10
Battery replacement.................8-10
Reinitialisation procedure after battery
reconnection......................8-12
Jump-starting.....................8-12
Drive belt..........................8-12
Spark plugs.........................8-12
Air cleaner filter......................8-13
Wiper blades........................8-13Cleaning.........................8-13
Replacing front window wiper blades......8-14
Replacing rear window wiper blade.......8-16
Brakes............................8-17
Self-adjusting brakes.................8-17
Fuses.............................8-17
Before replacing a fuse...............8-17
Engine compartment.................8-18
Passenger compartment..............8-19
Intelligent Key battery replacement........
.8-20
Checking the battery.................8-21
Replacing the battery.................8-21
Lights............................8-23
Exterior and interior lights..............8-23
Replacement procedures..............8-25
Wheels and tires......................8-27
Tire Pressure......................8-27
Tire inflation pressure................8-30
Tire labeling......................8-30
Types of tires.....................8-32
Tire chains.......................8-33
Tire wear and damage................8-33
Tire rotation......................8-34
Replacing wheels and tires.............8-34
Wheel balance.....................8-36

5. Wipe the engine oil filter sealing surface
with a clean rag.
CAUTION
•Be sure to remove any old gasket mate-
rial remaining on the sealing surface of
the engine. Failure to do so could lead to
an oil leak and engine damage.
•The dipstick must be inserted in place to
prevent oil spillage from the dipstick
hole when filling the engine with oil.
6. Coat the gasket on the new filter with
clean engine oil.
7. Screw on the oil filter until a slight resis-
tance is felt, then tighten an additional
2/3 turn.
Engine oil filter tightening torque: 19 ft-lb,
25 N•m
8. Start the engine and check for leakage
around the oil filter. Correct as required.
9. Turn the engine off and wait more than
15 minutes. Check the oil level. Add engine
oil if necessary.It is recommended that you visit an INFINITI
retailer if checking or replacement is required.
CAUTION
•Use only Shell DCT-M1 or equivalent.
Do not mix with other fluids.
•Using automatic transmission fluid
other than Shell DCT-M1 may cause de-
terioration in driveability and automatic
transmission durability, and may dam-
age the automatic transmission. Dam-
age caused by the use of fluids other
than as recommended is not covered by
the warranty.
WARNING
•Use only new fluid. Old, inferior, or con-
taminated fluid may damage the brake
systems. The use of improper fluids can
damage the brake system and affect the
vehicle's stopping ability.
•Clean the filler cap before removing.
•Brake fluid is poisonous and should be
stored carefully in marked containers
out of the reach of children.
CAUTION
•Do not spill the fluid on painted surfaces.
This will damage the paint. If fluid is
spilled, wash with water.
NDI1599
AUTOMATIC TRANSMISSION FLUID
(ATF)BRAKE FLUID
Do-it-yourself8-7