brakes INFINITI QX30 2018 Owner's Manual

STORAGE NETS (IF EQUIPPED)
WARNING
Do not place sharp objects in the nets to
help prevent injury in an accident or sudden
stop.
Storage nets are fitted in the front-passenger
footwell and on the back of the driver's and
front passenger seat.
PARCEL SHELF
WARNING
•Never put anything on the parcel shelf,
no matter how small. Any object on it
could cause an injury in case of an acci-
dent or if the brakes are applied sud-
denly.
•Do not leave the parcel shelf in position
when it is disengaged from the grooves.
•Properly secure all cargo to help prevent
it from sliding or shifting. Do not place
cargo higher than the seatbacks. In a
sudden stop or collision, unsecured
cargo could cause personal injury
•Properly secure cargo and do not allow
it to contact the top tether strap when it
is attached to the top tether anchor.
Cargo that is not properly secured or
cargo that contacts the top tether strap
may damage the top tether strap during
a collision. If the cargo cover contacts
the top tether strap when it is attached
to the top tether anchor, remove the
cargo cover from the vehicle or secure it
on the cargo floor below its attachment
location. If the cargo cover is not re-
moved, it may damage the top tether
strap during a collision. Your child could
be seriously injured or killed in a collision
if the child restraint top tether strap is
damaged.
•Do not use the cargo cover if the rear
seats are folded down.
Removal
1. Open the lift gate (see "Lift gate lock").
2. Detach both of the cords (left and right)
1from the inside of the lift gate.
3. Detach the parcel shelf
2by simply pull-
ing it rearwards through the lift gate
opening.
NIC2687NIC2672
Instruments and controls2-85

drive when under the influence of alcohol or
drugs (including prescription or over the-
counter drugs which may cause drowsiness).
Always wear your seat belt as outlined in the
“Safety – Seats, seat belts and supplemental
restraint system” section of this manual, and
also instruct your passengers to do so.
Seat belts help reduce the risk of injury in
collisions and rollovers.In a rollover crash, an
unbelted or improperly belted person is sig-
nificantly more likely to be injured or killed
than a person properly wearing a seat belt.
OFF-ROAD RECOVERY
While driving, the right side or left side wheels
may unintentionally leave the road surface. If
this occurs, maintain control of the vehicle by
following the procedure below. Please note
that this procedure is only a general guide.
The vehicle must be driven as appropriate
based on the conditions of the vehicle, road
and traffic.
1. Remain calm and do not overreact.
2. Do not apply the brakes.
3. Maintain a firm grip on the steering wheel
with both hands and try to hold a straight
course.4. When appropriate, slowly release the ac-
celerator pedal to gradually slow the ve-
hicle.
5. If there is nothing in the way, steer the
vehicle to follow the road while vehicle
speed is reduced. Do not attempt to drive
the vehicle back onto the road surface
until vehicle speed is reduced.
6. When it is safe to do so, gradually turn the
steering wheel until both tires return to
the road surface. When all tires are on the
road surface, steer the vehicle to stay in
the appropriate driving lane.
If you decide that it is not safe to return
the vehicle to the road surface based on
vehicle, road or traffic conditions, gradu-
ally slow the vehicle to a stop in a safe
place off the road.
RAPID AIR PRESSURE LOSS
Rapid air pressure loss or a “blow-out” can
occur if the tire is punctured or is damaged
due to hitting a curb or pothole. Rapid air
pressure loss can also be caused by driving on
under-inflated tires.
Rapid air pressure loss can affect the han-
dling and stability of the vehicle, especially at
highway speeds.Help prevent rapid air pressure loss by main-
taining the correct air pressure and visually
inspect the tires for wear and damage. For
additional information, refer to “Wheels and
tires” in the “Maintenance and do-it-yourself”
section of this manual. If a tire rapidly loses air
pressure or “blows-out” while driving, main-
tain control of the vehicle by following the
procedure below. Please note that this pro-
cedure is only a general guide. The vehicle
must be driven as appropriate based on the
conditions of the vehicle, road and traffic.
WARNING
The following actions can increase the
chance of losing control of the vehicle if
there is a sudden loss of tire air pressure.
Losing control of the vehicle may cause a
collision and result in personal injury.
•The vehicle generally moves or pulls in
the direction of the flat tire.
•Do not rapidly apply the brakes.
•Do not rapidly release the accelerator
pedal.
•Do not rapidly turn the steering wheel.
1. Remain calm and do not overreact.
Starting and driving5-9

•Do not shift gears while driving on
downhill grades as this could cause loss
of control of the vehicle.
•Stay alert when driving to the top of a
hill. At the top there could be a drop-off
or other hazard that could cause an ac-
cident.
•If your engine stalls or you cannot make
it to the top of a steep hill, never at-
tempt to turn around. Your vehicle could
tip or roll over. Always back straight
down in R (Reverse) gear and apply
brakes to control your speed.
•Heavy braking going down a hill could
cause your brakes to overheat and fade,
resulting in loss of control and an acci-
dent. Apply brakes lightly and use a low
gear to control your speed.
•Unsecured cargo can be thrown around
when driving over rough terrain. Prop-
erly secure all cargo so it will not be
thrown forward and cause injury to you
or your passengers.
•Secure heavy loads in the cargo area as
far forward and as low as possible. Do
not equip the vehicle with tires larger
than specified in this manual. This could
cause your vehicle to roll over.
•Do not grip the inside or spokes of the
steering wheel when driving off-road.
The steering wheel could move suddenly
and injure your hands. Instead drive with
your fingers and thumbs on the outside
of the rim.
•Before operating the vehicle, ensure
that the driver and all passengers have
their seat belts fastened.
•Always drive with the floor mats in place
as the floor may become hot.
•Lower your speed when encountering
strong crosswinds. With a higher center
of gravity, your INFINITI is more af-
fected by strong side winds. Slower
speeds ensure better vehicle control.
•Do not drive beyond the performance
capability of the tires, even with AWD
engaged.
•For AWD equipped vehicles, do not at-
tempt to raise two wheels off the
ground and shift the transmission to any
drive or reverse position with the engine
running. Doing so may result in drive-
train damage or unexpected vehicle
movement which could result in serious
vehicle damage or personal injury.
•Do not attempt to test an AWD
equipped vehicle on a 2-wheel dyna-
mometer (such as the dynamometers
used by some states for emissions test-
ing), or similar equipment even if the
other two wheels are raised off the
ground. Make sure you inform test facil-
ity personnel that your vehicle is
equipped with AWD before it is placed
on a dynamometer. Using the wrong
test equipment may result in drivetrain
damage or unexpected vehicle move-
ment which could result in serious ve-
hicle damage or personal injury.
•When a wheel is off the ground due to an
unlevel surface, do not spin the wheel
excessively.
•Accelerating quickly, sharp steering ma-
neuvers or sudden braking may cause
loss of control.
•If at all possible, avoid sharp turning ma-
neuvers, particularly at high speeds.
Your INFINITI vehicle has a higher cen-
ter of gravity than a passenger car. The
vehicle is not designed for cornering at
the same speeds as passenger cars. Fail-
ure to operate this vehicle correctly
could result in loss of control and/or a
rollover accident.
Starting and driving5-11

•Always use tires of the same type, size,
brand, construction (bias, bias-belted,
or radial), and tread pattern on all four
wheels. Install tire chains on the front
wheels when driving on slippery roads
and drive carefully.
•Be sure to check the brakes immediately
after driving in mud or water. .
•Avoid parking your vehicle on steep hills.
If you get out of the vehicle and it rolls
forward, backward or sideways, you
could be injured.
•Whenever you drive off-road through
sand, mud or water as deep as the wheel
hub, more frequent maintenance may be
required. For additional information, re-
fer to "Maintenance schedules".
ALL-WHEEL DRIVE (AWD)
DRIVING SAFETY PRECAUTIONS
(IF SO EQUIPPED)
WARNING
•Replacing tires with those not originally
specified by INFINITI could affect the
proper operation of the TPMS.
•Always use tires of the same type, size,
brand, construction (bias, bias-belted or
radial), and tread pattern on all four
wheels. Install tire chains on the front
wheels when driving on slippery roads
and drive carefully.
•This vehicle is not designed for off-road
(rough road) use. Do not drive on sandy
or muddy roads that tires may get stuck
in.
•For AWD equipped vehicles, do not at-
tempt to raise two wheels off the
ground and shift the transmission to any
D (Drive) or R (Reverse) position with
the engine running. Doing so may result
in drivetrain damage or unexpected ve-
hicle movement which could result in se-
rious vehicle damage or personal injury
•Do not attempt to test an AWD
equipped vehicle on a 2-wheel dyna-
mometer, (such as the dynamometers
used by some states for emissions test-
ing), or similar equipment even if the
other two wheels are raised off the
ground. Make sure you inform test facil-
ity personnel that your vehicle is
equipped with AWD before it is placed
on a dynamometer. Using the wrong
test equipment may result in drivetrain
damage or unexpected vehicle move-
ment which could result in serious ve-
hicle damage or personal injury.
•When a wheel is off the ground due to an
unlevel surface, do not spin the wheel
excessively.
5-12Starting and driving

RADAR MAINTENANCE
The two radar sensor unitsAfor the BSW
system are located near the rear bumper.
Always keep the area near the radar sensors
clean.
The radar sensors may be blocked by tempo-
rary ambient conditions such as splashing
water, mist or fog.
The blocked condition may also be caused by
objects such as ice, frost or dirt obstructing
the radar sensors.
Check for and remove objects obstructing
the area around the radar sensors.
Do not attach stickers (including transparent
material), install accessories or apply addi-
tional paint near the radar sensors.Do not strike or damage the area around the
radar sensors. It is recommended you consult
an INFINITI retailer if the area around the
radar sensors is damaged due to a collision.
FCC NOTICE
For USA:
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) This device may not
cause harmful interference, and (2) this de-
vice must accept any interference received,
including interference that may cause unde-
sired operation.
NOTE
Changes or modification not expressly ap-
proved by the party responsible for compli-
ance could void the user’s authority to oper-
ate the equipment.
For Canada:
This device complies with Industry Canada
license-exempt RSS standard(s). Operation
is subject to the following two conditions: (1)
this device may not cause harmful interfer-
ence, and (2) this device must accept any
interference received, including interference
that may cause undesired operation of the
device.Cruise control maintains a constant road
speed for you. It brakes automatically in order
to avoid exceeding the set speed. You must
select a lower gear in good time on long and
steep downhill gradients, especially if the ve-
hicle is laden or towing a trailer.WARNING
For vehicles with automatic transmission,
you need to have selected manual drive
program M (see "Manual drive program"
earlier in this section). By doing so, you will
make use of the braking effect of the en-
gine. This relieves the load on the brake
system and prevents the brakes from over-
heating and wearing too quickly.
Use cruise control only if road and traffic
conditions are appropriate for maintaining a
steady speed for a prolonged period. You can
set the cruise control at any road speed
above 20 MPH (30 km/h).
The speed indicated in the speedometer may
differ slightly from the set speed.
NAA1640
CRUISE CONTROL
5-46Starting and driving

Storing the current speed or calling up the
last stored speed:
WARNING
If you call up a stored speed and this is
different from the current speed, the ve-
hicle accelerates or brakes. If you do not
know what the stored speed is, the vehicle
may accelerate or brake unexpectedly.
There is a risk of an accident.
Take the traffic conditions into account
before calling up the stored speed. If you do
not know what the stored speed is, store
the desired speed again.
1. Briefly pull the cruise control lever to-
wards you
2.
2. Remove your foot from the accelerator
pedal. The first time cruise control is acti-
vated, it stores the current speed or if a
speed has previously been stored, it regu-
lates the speed of the vehicle to the pre-
viously stored speed.
Setting a speed
Bear in mind that it may take a brief moment
until the vehicle has accelerated or braked to
the set speed.
1. Press the cruise control lever up
1for a
higher speed or down
3for a lower
speed.
2. Keep the cruise control lever pressed until
the desired speed is reached.
3. Release the cruise control lever, The new
speed is stored.
4. To adjust the set speed in 1 MPH (1 km/h)
increments: briefly press the cruise control
lever up
1or down3to the pressure
point. The last stored speed increases or
decreases in 1 MPH (1 km/h) increments.
5. To adjust the set speed in 10 MPH
(10 km/h) increments: briefly press the
cruise control lever up
1or down3beyond the pressure point. The last stored
speed increases or decreases in 10 MPH
(10 km/h) increments.NOTE
Cruise control is not deactivated if you de-
press the accelerator pedal. For example, if
you accelerate briefly to overtake, cruise
control adjusts the vehicle's speed to the last
speed stored after you have finished over-
taking.
Deactivating cruise control
There are several ways to deactivate cruise
control:
•Briefly press the cruise control lever for-
ward
4.
or
•Brake.
Cruise control is automatically deactivated if:
•The vehicle is secured with the electric
parking brake.
•You are driving at less than 20 MPH
(30 km/h).
•VDC intervenes or you deactivate VDC.
5-48Starting and driving

If cruise control is deactivated, you will hear a
warning tone. You will see the [Cruise Control
Off] message in the vehicle information dis-
play for approximately five seconds.
NOTE
The last speed stored is cleared when you
switch off the engine.WARNING
Failure to follow the warnings and instruc-
tions for proper use of the ICC system
could result in serious injury or death.
•ICC is not a collision avoidance or warn-
ing device. For highway and freeway
way use only and not intended for con-
gested areas or city driving. Failure to
apply the brakes could result in an acci-
dent. It is the driver’s responsibility to
stay alert, drive safely, and be in control
of the vehicle at all times.
•Always observe posted speed limits and
do not set the speed over them.
•Always drive carefully and attentively
when using the ICC. Read and under-
stand the Owner’s Manual thoroughly
before using the ICC system. To avoid
serious injury or death, do not rely on the
system to prevent accidents or to con-
trol the vehicle’s speed in emergency
situations. Do not use the ICC system
except in appropriate road and traffic
conditions.
INTELLIGENT CRUISE CONTROL
(ICC) SYSTEM (FULL SPEED RANGE)
(IF EQUIPPED)
Starting and driving5-49

OPERATING ICC
To set cruising speed, accelerate your vehicle
to the desired speed and quickly push the
cruise control lever, up
1or down4. Take
your foot off the accelerator pedal. Your ve-
hicle will maintain the set speed.
NOTE
If you do not fully release the accelerator
pedal, the [ICC Suspended] message ap-
pears in the vehicle information display. The
set distance to a slower-moving vehicle in
front will then not be maintained. You will be
driving at the speed you determine by the
position of the accelerator pedal.
You can also activate the ICC when station-
ary. The lowest speed that can be set is
20 MPH (30 km/h ).
System operation
The driver sets the desired vehicle speed
based on the road conditions. The ICC sys-
tem maintains the set vehicle speed, similar to
standard cruise control, as long as no vehicle
is detected in the lane ahead. The ICC system
displays the set speed for 5 seconds after the
cruise control lever is activated.
Vehicle detected ahead:
When a vehicle is detected in the lane ahead,
the ICC system decelerates the vehicle by
controlling the throttle and applying the
brakes to match the speed of a slower vehicle
ahead. The system then controls the vehicle
speed based on the speed of the vehicle
ahead to maintain the driver selected dis-
tance.The brake lights of the vehicle come on when
braking is performed by the ICC system.
When the brake operates, a noise may be
heard. This is not a malfunction.
When a vehicle ahead is detected, the vehicle
ahead symbol
1appears in the vehicle infor-
mation display.
Vehicle ahead not detected:
When a vehicle is no longer detected ahead,
the ICC system gradually accelerates your
vehicle to resume the previously set vehicle
speed. The ICC system then maintains the set
speed.
When a vehicle is no longer detected, the
vehicle ahead display turns off
2.
NSD582ANSD615
System set display with vehicle ahead
NSD616
System set display without vehicle ahead
Starting and driving5-53

display. The set distance to a slower-moving
vehicle in front will then not be maintained.
You will be driving at the speed you deter-
mine by the position of the accelerator pedal.
You can also activate ICC when stationary.
The lowest speed that can be set is 20 MPH
(30 km/h).
Stopping
WARNING
•To help avoid risk of injury or death
through unintended operation of the
vehicle and/or its systems, do not leave
children, people who require the assis-
tance of others, or pets unattended in
your vehicle.
•The ICC system should only be used to
keep the vehicle stationary when the
driver is actively using the system.
When parking the vehicle, make sure to
turn OFF the ICC system, use the brake,
press the PARK (P) button, and place
the ignition switch in the LOCK position
prior to exiting the vehicle. Failure to do
so could lead to serious injury or death.
The ICC system will not hold the vehiclein place after coming to a stop when any
of the following conditions occur:
–There is a malfunction in the system
or in the voltage supply.
–The ICC system has been deactivated
with the cruise control lever, e. g. by a
vehicle occupant.
–The accelerator pedal has been de-
pressed, e.g. by a vehicle occupant.
For further information on deactivating the
ICC system, see "ICC switch (cruise control
lever)" earlier in this section
If the ICC system detects that the vehicle in
front is stopping, it brakes your vehicle until it
is stationary (within the braking limitations of
the system).
Once your vehicle is stationary, it remains
stationary and you do not need to depress
the brake.
NOTE
Depending on the specified minimum dis-
tance, your vehicle will come to a standstill
at a sufficient distance behind the vehicle in
front. The specified minimum distance is set
using the control on the cruise control lever.
How to change the set distance to
the vehicle ahead
The distance to the vehicle ahead can be
selected at any time depending on the traffic
conditions.
To increase the distance to the vehicle ahead,
turn the knob
3toward the rear2.To
decrease the distance to the vehicle ahead,
turn the knob
3toward the front1.
You can see this distance in the vehicle infor-
mation display.
The distance to the vehicle ahead will change
according to the vehicle speed. The higher the
vehicle speed, the longer the distance.
NSD583A
Starting and driving5-55

•As there is a performance limit to the
distance control function, never rely
solely on the ICC system. This system
does not correct careless, inattentive or
absent-minded driving, or overcome
poor visibility in rain, fog, or other bad
weather. Decelerate the vehicle speed
by depressing the brake pedal, depend-
ing on the distance to the vehicle ahead
and the surrounding circumstances in
order to maintain a safe distance be-
tween vehicles.
•If the vehicle ahead comes to a stop, the
vehicle decelerates to a standstill within
the limitations of the system. Once the
vehicle is stationary, it remains station-
ary and you do not need to depress the
brake pedal.
•Always pay attention to the operation of
the vehicle and be ready to manually con-
trol the proper following distance. The
ICC system may not be able to maintain
the selected distance between vehicles
(following distance) or selected vehicle
speed under some circumstances.
•Normally when controlling the distance
to a vehicle ahead, this system auto-
matically accelerates or deceleratesyour vehicle according to the speed of
the vehicle ahead. If required, depress
the accelerator to properly accelerate
your vehicle when acceleration is re-
quired for a lane change. Depress the
brake pedal when deceleration is re-
quired to maintain a safe distance to the
vehicle ahead due to its sudden braking
or if a vehicle cuts in. Always stay alert
when using the ICC system.
•The system may not detect the vehicle in
front of you in certain road or weather
conditions. To avoid accidents, never
use the ICC system under the following
conditions:
–On roads where the traffic is heavy or
there are sharp curves.
–On slippery road surfaces such as on
ice or snow, etc.
–During bad weather (rain, fog, snow,
etc.).
–When rain, snow or dirt adhere to the
system sensor.
–On steep downhill roads (the vehicle
may go beyond the set vehicle speed
and frequent braking may result in
overheating the brakes).
–On repeated uphill and downhill
roads.–When traffic conditions make it diffi-
cult to keep a proper distance be-
tween vehicles because of frequent
acceleration or deceleration.
–If there is interference by other radar
sources.
•Do not use the ICC system if you are
towing a trailer. The system may not de-
tect a vehicle ahead.
•In some road or traffic conditions, a ve-
hicle or object can unexpectedly come
into the sensor detection zone and cause
automatic braking. You may need to
control the distance from other vehicles
using the accelerator pedal. Always stay
alert and avoid using the ICC system
when it is not recommended in this sec-
tion.
•The distance sensor will not detect the
following objects:
–Stationary and slow moving vehicles.
–Pedestrians or objects in the road-
way.
–Oncoming vehicles in the same lane.
–Motorcycles traveling offset in the
travel lane.
Starting and driving5-57