maintenance reset INFINITI QX30 2018 Owner's Manual

REINITIALISATION PROCEDURE
AFTER BATTERY
RECONNECTION
If the battery has been reconnected, check
the following items:
•Clock setting (if so equipped). For details,
see "Clock", or the separately provided
INFINITI InTouch Owner’s Manual.
•Reset the desired radio stations to the pre-
set station buttons. For details, see the
audio device descriptions in the separately
provided INFINITI InTouch Owner’s
Manual.
JUMP-STARTING
If jump-starting is necessary, see "Jump
starting". If the engine does not start by jump
starting, the battery may have to be replaced.
It is recommended that you visit an INFINITI
retailer for this service.
WARNING
Be sure the ignition switch is in the OFF
position before servicing drive belt. The en-
gine could rotate unexpectedly.
1. Visually inspect each belt for signs of un-
usual wear, cuts, fraying or looseness. If
the belt is in poor condition or loose, have
it replaced or adjusted. It is recommended
that you visit an INFINITI retailer for this
service.
2. Have the belts checked regularly for con-
dition and tension in accordance with the
maintenance schedule as shown in a
separately provided Warranty Informa-
tion and Maintenance booklet.Replace the spark plugs according to the
maintenance schedule shown in a separate
maintenance booklet.
If replacement is required, it is recommended
that you visit an INFINITI retailer.
Always replace spark plugs with recom-
mended or equivalent ones.
WARNING
Be sure the engine and ignition switch are
off and that the parking brake is engaged
securely.
CAUTION
•Be sure to use the correct socket to re-
move the spark plugs. An incorrect
socket can cause damage to the spark
plugs.
DRIVE BELT SPARK PLUGS
8-12Do-it-yourself

Information about service
Resetting the maintenance service interval
display:
CAUTION
If the maintenance service interval display
has been inadvertently reset, this setting
can be corrected at an INFINITI retailer.
Have service work carried out as described
in the Maintenance Schedule. This may
otherwise lead to increased wear and dam-
age to the major assemblies or the vehicle.
An INFINITI retailer will reset the mainte-
nance service interval display after the service
work has been carried out. You can also ob-
tain further information on maintenance
work, for example.Special service requirements:
The prescribed service interval is based on
normal operation of the vehicle. Service work
will need to be performed more often if the
vehicle is operated under arduous conditions
or increased loads, for example:
•Regular city driving with frequent interme-
diate stops
•If the vehicle is primarily used to travel
short distance
•For frequent operation in mountainous
terrain or on poor road surfaces
•If the engine is often left idling for long
periods
In these or similar operating conditions, have,
for example, the air filter, engine oil and oil
filter changed more frequently. The tires must
be checked more frequently if the vehicle is
operated under increased loads. Further in-
formation can be obtained at an INFINITI
retailer.
9-8Maintenance and Schedules

For Canada:
If you believe that your vehicle has a defect
which could cause a crash or could cause
injury or death, you should immediately in-
form Transport Canada in addition to notify-
ing INFINITI.
If Transport Canada receives complaints, it
may open an investigation, and if it finds that
a safety defect exists in a group of vehicles, it
may request that INFINITI conduct a recall
campaign. However, Transport Canada can-
not become involved in individual problems
between you, your retailer, or INFINITI.
You may contact Transport Canada’s Defect
Investigations and Recalls Division toll free
at 1-800-333- 0510. You may also report
safety defects online at:
https://wwwapps.tc.gc.ca/Saf-Sec- Sur/7/
PCDB-BDPP/Index.aspx.
Additional information concerning motor
vehicle safety may be obtained from Trans-
port Canada’s Road Safety Information
Center at 1-800-333- 0371 or online at
www.tc.gc.ca/roadsafety (English speakers)
or www.tc.gc.ca/securiteroutiere (French
speakers).
To notify INFINITI of any safety concerns
please contact our Consumer Information
Center toll free at 1-800- 361-4792.WARNING
A vehicle equipped with All-Wheel Drive
(AWD) should never be tested using a two
wheel dynamometer (such as the dyna-
mometers used by some states for emis-
sions testing), or similar equipment. Make
sure you inform test facility personnel that
your vehicle is equipped with AWD before
it is placed on a dynamometer. Using the
wrong test equipment may result in trans-
mission damage or unexpected vehicle
movement which could result in serious ve-
hicle damage or personal injury.
Due to legal requirements in some states and
Canadian Provinces, your vehicle may be re-
quired to be in what is called the “ready con-
dition” for an Inspection/Maintenance (I/M)
test of the emission control system.
The vehicle is set to the “ready condition”
when it is driven through certain driving pat-
terns. Usually, the “ready condition” can be
obtained by ordinary usage of the vehicle.
If a powertrain system component is repaired
or the battery is disconnected, the vehicle
may be reset to a “not ready condition”. Be-
fore taking the I/M test, check the vehicle’s
inspection/maintenance test readiness con-
dition. Place the ignition switch in the ON
position without starting the engine. If theMalfunction Indicator Light (MIL) comes on
steady for 20 seconds and then blinks for
10 seconds, the I/M test condition is “not
ready”. If the MIL does not blink after 20 sec-
onds, the I/M test condition is “ready”.
It is recommended you contact an INFINITI
retailer to set the “ready condition” or to pre-
pare the vehicle for testing.
READINESS FOR INSPECTION/
MAINTENANCE (I/M) TEST
10-18Technical information