seat adjustment INFINITI QX30 2018 Owner's Manual

Table of contents
Illustrated table of contents
Safety — seats, seat belts and supplemental restraint system
Instruments and controls
Pre-driving checks and adjustments
Display screen, heater and air conditioner, and audio system
Starting and driving
In case of emergency
Appearance and care
Do-it-yourself
Maintenance and Schedules
Technical information
Index
0
1
2
3
4
5
6
7
8
9
10
11

WARNING
•The seatback should not be reclined any
more than needed for comfort. Seat
belts are most effective when the pas-
senger sits well back and straight up in
the seat. If the seatback is reclined, the
risk of sliding under the lap belt and be-
ing injured is increased.
•For the most effective protection when
the vehicle is in motion, the seat should
be upright. Always sit well back and up-
right in the seat with both feet on the
floor and adjust the seat properly. (See
"Seat belts" later in this section.)
•After adjustment, gently rock in the seat
to make sure it is securely locked.
•To help avoid risk of injury or death
through unintended operation of the
vehicle and/or its systems, do not leave
children, people who require the assis-
tance of others, or pets unattended in
your vehicle. Additionally, the tempera-
ture inside a closed vehicle on a warm
day can quickly become high enough to
cause a significant risk of injury or death
to people and pets.
•Do not leave children unattended inside
the vehicle. They could unknowingly ac-
tivate switches or controls or make the
vehicle move. Unattended children could
become involved in serious accidents.
•Do not adjust the driver’s seat while
driving so full attention may be given to
vehicle operation. The seat may move
suddenly and could cause loss of control
of the vehicle.
CAUTION
•When moving the seats forward or
backward, or returning a reclined seat-
back to its upright position, make sure
you hold onto the seatback while oper-
ating. If the seatback is not held, the
seat or seatback may move suddenly
and could cause injury.
•When adjusting the seat positions, be
sure not to contact any moving parts to
avoid possible injuries and/or damage.
SSS0133AZ
SEATS
1-2Safety — seats, seat belts and supplemental restraint system

FRONT SEATS
Manual seat adjustment
Forward and backward:
Pull the lever
1up and hold it while sliding
the seat forward or backward to the pre-
ferred position. Release the lever to lock the
seat in position.
Seat cushion angle (if equipped):
Adjust the angles so that your thighs are
lightly supported. Turn handwheel
2for-
wards or backwards.Seat lifter (if equipped):
Repeatedly pull up or push down the adjust-
ing lever
3, to adjust the seat height to the
desired position.
Seatback angle:
Relieve the pressure on the seatback and turn
handwheel
4forwards or backwards.
The reclining feature allows the adjustment
of the seatback for occupants of different
sizes to help obtain the proper seat belt fit.
(See "Seat belts" later in this section.)
The seatback may be reclined to allow occu-
pants to rest when the vehicle is parked.Lumbar support:
The lumbar support feature provides lower
back support to the driver.
Push each side of the adjusting switch to
adjust the seat lumbar area until the desired
position is achieved.
1To raise the seatback contour
2To soften the seatback contour
3To lower the seatback contour
4To harden the seatback contour
NIC2605NIC2607
Safety — seats, seat belts and supplemental restraint system1-3

Power seat adjustment
Operating tips:
•The power seat motor has an auto-reset
overload protection circuit. If the motor
stops during the seat adjustment, wait
30 seconds, then reactivate the switch.
•If the seat motor stops during seat adjust-
ment, check for obstructions. Remove the
obstruction before continuing.
•To avoid discharge of the battery, do not
operate the power seats for a long period
of time when the engine is not running.
NOTE
You can store the seat settings using the
memory function (see " Memory function
(if equipped)").Forward and backward:
Move the adjusting switch
1forward or
backward as shown to move the seat to the
desired position.
Reclining:
Move the adjusting switch
2forward or
backward as shown to move the seatback to
the desired position.
The reclining feature allows the adjustment
of the seatback for occupants of different
sizes to help obtain the proper seat belt fit.
(See "Seat belts" later in this section.)
The seatback may be reclined to allow occu-
pants to rest when the vehicle is parked.Seat lifter (if equipped):
1. Pull up or push down the adjusting switch
3as shown to adjust the seat height until
the desired position is achieved.
2. Tilt up or down the adjusting switch
4as
shown to adjust the front angle of the
seat until the desired position is achieved.
NIC2606
1-4Safety — seats, seat belts and supplemental restraint system

ARMREST (IF EQUIPPED)
Rear
Pull the tab and draw the armrest1forward
as shown until it is horizontal.
Indicates that the seating position is
equipped with a head restraint.
Indicates that the seating position is
equipped with a non-removable head rest.
WARNING
Head restraints/headrests supplement the
other vehicle safety systems. They may
provide additional protection against in-
jury in certain rear end collisions. Adjust-
able head restraints/headrests must be
adjusted properly, as specified in this sec-
tion. Check the adjustment after someone
else uses the seat. Do not attach anything
to the head restraint/headrest stalks or
remove the head restraint/headrest. Do
not use the seat if the head restraint/
headrest has been removed. If the head
restraint/headrest was removed, reinstalland properly adjust the head restraint/
headrest before an occupant uses the seat-
ing position. Failure to follow these in-
structions can reduce the effectiveness of
the head restraints/headrests. This may
increase the risk of serious injury or death
in a collision.
•Your vehicle is equipped with head
restraints/headrests that may be inte-
grated, adjustable or non-adjustable.
•Adjustable head restraints/headrests have
multiple notches along the stalk to lock them
in a desired adjustment position.
•The non-adjustable head restraints/
headrests have a single locking notch to
secure them to the seat frame.
•Proper Adjustment:
– For the adjustable type, align the head
restraint/headrest so the center of your
ear is approximately level with the cen-
ter of the head restraint/headrest.
– If your ear position is still higher than
the recommended alignment, place the
head restraint/headrest at the highest
position.
NIC2611NPA1500
HEAD RESTRAINTS/HEADRESTS
Safety — seats, seat belts and supplemental restraint system1-7

Unfastening the seat belts
To unfasten the seat belt, push the button on
the buckle and guide the seat belt as it auto-
matically retracts.
Checking seat belt operation
Seat belt retractors are designed to lock seat
belt movement by two separate methods:
•When the belt is pulled quickly from the
retractor.
•When the vehicle slows down rapidly.
To increase your confidence in the seat belts,
check the operation as follows:
•Grasp the shoulder belt and pull forward
quickly. The retractor should lock and re-
strict further belt movement.
If the retractor does not lock during this
check, get the system checked. It is recom-
mended that you visit an INFINITI retailer for
this service, or to learn more about seat belt
operation.
Shoulder belt height adjustment
(if equipped)
The shoulder belt anchor height should be
adjusted to the position that is best for you.
(See "Fastening the seat belts " earlier in this
section).
•To adjust, push the buttonAas shown
and then move the shoulder belt anchor to
the desired position so that the belt passes
over the center of the shoulder. The belt
should be away from your face and neck,
but not falling off of your shoulder. Re-
lease the adjustment button to lock the
shoulder belt anchor into position.
SSS0326ZSSS0896Z
Safety — seats, seat belts and supplemental restraint system1-15

WARNING
•After adjustment, release the adjust-
ment button and then try to move the
shoulder belt down to make sure that it
is securely fixed in position.
•The shoulder belt anchor height should
be adjusted to the position that is best
for you. Failure to do so may reduce the
effectiveness of the entire restraint sys-
tem and increase the chance or severity
of injury in an accident.
SEAT BELT EXTENDERS
If, because of body size or driving position, it
is not possible to properly fit the lap/shoulder
belt and fasten it, an extender that is compat-
ible with the installed seat belts is available
that can be purchased. The extender adds
approximately 8 in (200 mm) of length and
may be used for either the driver or front
passenger seating position. It is recom-
mended you visit an INFINITI retailer for as-
sistance with purchasing an extender if an
extender is required.
WARNING
•Only INFINITI seat belt extenders, made
by the same company which made the
original equipment seat belts, should be
used with the INFINITI seat belts.
•Adults and children who can use the
standard seat belt should not use an ex-
tender. Such unnecessary use could re-
sult in serious personal injury in the
event of an accident.
•Never use seat belt extenders to install
child restraints. If the child restraint is
not secured properly, the child could be
seriously injured in a collision or a sud-
den stop.
SEAT BELT MAINTENANCE
•To clean the seat belt webbing,apply a
mild soap solution or any solution recom-
mended for cleaning upholstery or carpets.
Then wipe with a cloth and allow the seat
belts to dry in the shade. Do not allow the
seat belts to retract until they are com-
pletely dry.
•If dirt builds up in the shoulder belt guide
of the seat belt anchors, the seat belts may
retract slowly. Wipe the shoulder belt
guide with a clean, dry cloth.
•Periodically check to see that the seat belt
and the metal components, such as buck-
les, tongues, retractors, flexible wires and
anchors, work properly. If loose parts, de-
terioration, cuts or other damage on the
webbing is found, the entire seat belt as-
sembly should be replaced.
1-16Safety — seats, seat belts and supplemental restraint system

If the child restraint is equipped with a top
tether strap, route the top tether strap
and secure the tether strap to the tether
anchor point. For additional information,
refer to "Installing top tether strap".
Do not install child restraints that require
the use of a top tether strap in seating
positions that do not have a top tether
anchor.
3. The back of the child restraint should be
secured against the vehicle seatback.
If necessary, adjust or remove the head
restraint/headrest to obtain the correct
child restraint fit. If the head restraint/
headrest is removed, store it in a secure
place.Be sure to reinstall the head
restraint/headrest when the child re-
straint is removed.For additional infor-
mation about head restraint/headrest
adjustment, refer to "Head restraints/
Headrests". If the seating position does
not have an adjustable head restraint/
headrest and it is interfering with the
proper child restraint fit, try another seat-
ing position or a different child restraint.4. For child restraints that are equipped with
webbing-mounted attachments, remove
any additional slack from the webbing of
the anchor attachments. Press down-
ward and rearward firmly in the center of
the child restraint with your knee to com-
press the vehicle seat cushion and seat-
back while tightening the webbing of the
anchor attachments.
5. Tighten the tether strap according to the
manufacturer's instructions to remove
any slack.6. After attaching the child restraint, test it
before you place the child in it. Push it
from side to side while holding the child
restraint near the LATCH attachment
path. The child restraint should not move
more than 1 inch (25 mm), from side to
side. Try to tug it forward and check to see
if the LATCH attachment holds the re-
straint in place. If the restraint is not se-
cure, tighten the LATCH attachment as
necessary, or put the restraint in another
seat and test it again. You may need to try
a different child restraint. Not all child re-
straints fit in all types of vehicles.
7. Check to make sure the child restraint is
properly secured prior to each use. If the
child restraint is loose, repeat steps 3
through 6.
SSS0647Z
Forward-facing — step 4
SSS0638Z
Forward-facing — step 6
1-28Safety — seats, seat belts and supplemental restraint system

restraint could tip over or be loose and
cause injury to a child in a sudden stop or
collision. Also, it can change the operation
of the front passenger air bag. For addi-
tional information, refer to "Front passen-
ger air bag and status light".
For additional information, refer to all Warn-
ings and Cautions in the "Child safety" and
"Child restraints" before installing a child re-
straint.
Do not use the lower anchors if the combined
weight of the child and the child restraint
exceeds 65 lb (29.5 kg). If the combined
weight of the child and the child restraint is
greater than 65 lb (29.5 kg), use the vehicle
seat belt (not the lower anchors) to install the
child restraint. Be sure to follow the child
restraint manufacturer's instructions for in-
stallation.
Follow these steps to install a forward-
facing child restraint using the vehicle seat
belt in the rear seats or in the front passenger
seat:1.If you must install a child restraint in the
front seat, it should be placed in a
forward-facing direction only. Move the
seat to the rearmost position. Child re-
straints for infants must be used in the
rear-facing direction and, therefore,
must not be used in the front seat.2. Position the child restraint on the seat.
Always follow the child restraint manu-
facturer's instructions. The back of the
child restraint should be secured against
the vehicle seatback. If necessary, adjust
or remove the head restraint/headrest to
obtain the correct child restraint fit. If the
head restraint/headrest is removed, store
it in a secure place.Be sure to reinstall the
head restraint/headrest when the child
restraint is removed.For additional infor-
mation about head restraint/headrest
adjustment, removal and installation, re-
fer to "Head restraints/Headrests".
If the seating position does not have an
adjustable head restraint/headrest and it
is interfering with the proper child re-
straint fit, try another seating position or a
different child restraint.
WRS0699Z
Forward-facing (front passenger seat) —
step 1
1-30Safety — seats, seat belts and supplemental restraint system

3. Tighten the tether strap according to the
manufacturer's instructions to remove
any slack.
Center seating position with adjustable
head restraint/headrest:
1. Raise the head restraint/headrest. For
additional information about head
restraint/headrest adjustment, removal
and installation, refer to "Head restraints/
Headrests".
2. Position the top tether strap
1under
the head restraint/head rest and over
the seatback, between the two head
restraint/headrest stalks as shown.
3. Secure the tether strap to the tether an-
chor point
2on the seatback behind the
child restraint as shown.
4. Tighten the tether strap according to the
manufacturer's instructions to remove
any slack.
If you have any questions when installing
a top tether strap, it is recommended
that you visit an INFINITI retailer for this
service.
BOOSTER SEATS
For additional information on installing a
booster seat in your vehicle, follow the in-
structions outlined in this section.
Precautions on booster seats
WARNING
If a booster seat and seat belt are not used
properly, the risk of a child being injured or
killed in a sudden stop or collision greatly
increases:
•Make sure the shoulder portion of the
belt is away from the child's face and
neck and the lap portion of the belt does
not cross the stomach.
•Make sure the shoulder belt is not be-
hind the child or under the child’s arm.
•A booster seat must only be installed in a
seating position that has a lap/shoulder
belt.
Booster seats of various sizes are offered
by several manufacturers. When selecting
any booster seat, keep the following points in
mind:
LRS0501Z
LRS0464Z
1-34Safety — seats, seat belts and supplemental restraint system