display INFINITI QX30 2018 Owners Manual

5. Lightly apply the brake pedal to graduallystop the vehicle.
6. Turn on the hazard warning flashers and contact a roadside emergency service to
change the tire. For additional informa-
tion, refer to "Flat tire" in the "6. In case of
emergency" section.
DRINKING ALCOHOL/DRUGS
AND DRIVING
WARNING
Never drive under the influence of alcohol
or drugs. Alcohol in the bloodstream re-
duces coordination, delays reaction time
and impairs judgement. Driving after
drinking alcohol increases the likelihood of
being involved in an accident injuring your-
self and others. Additionally, if you are in-
jured in an accident, alcohol can increase
the severity of the injury.
INFINITI is committed to safe driving. How-
ever, you must choose not to drive under the
influence of alcohol. Every year thousands of
people are injured or killed in alcohol-related
accidents. Although the local laws vary on
what is considered to be legally intoxicated,
the fact is that alcohol affects all people dif-
ferently and most people underestimate the
effects of alcohol. Remember, drinking and driving don’t mix!
And that is true for drugs, too (over-the-
counter, prescription, and illegal drugs). Don’t
drive if your ability to operate your vehicle is
impaired by alcohol, drugs, or some other
physical condition.
DRIVING SAFETY PRECAUTIONS
Your INFINITI is designed for both normal
and off-road use. However, avoid driving in
deep water or mud as your INFINITI is mainly
designed for leisure use, unlike a conventional
off-road vehicle.
Remember that 2–wheel drive vehicles are
less capable than all-wheel drive (AWD)
models for rough road driving and extrication
when stuck in deep snow or mud, or the like.
Please observe the following precautions:
WARNING
•Spinning the front wheels on slippery
surfaces may cause the AWD warning
message to display and the AWD system
to automatically switch from the AWD
to 2WD mode. This could reduce the
traction. Be especially careful when
towing a trailer. (AWD models)
•Drive carefully when off the road and
avoid dangerous areas. Every person who drives or rides in this vehicle should
be seated with their seat belt fastened.
This will keep you and your passengers
in position when driving over rough ter-
rain.
•Do not drive across steep slopes. Instead
drive either straight up or straight down
the slopes. Off-road vehicles can tip
over sideways much more easily than
they can forward or backward.
•Many hills are too steep for any vehicle.
If you drive up them, you may stall. If you
drive down them, you may not be able to
control your speed. If you drive across
them, you may roll over.
•Do not shift gears while driving on
downhill grades as this could cause loss
of control of the vehicle.
•Stay alert when driving to the top of a
hill. At the top there could be a drop-off
or other hazard that could cause an ac-
cident.
•If your engine stalls or you cannot make
it to the top of a steep hill, never at-
tempt to turn around. Your vehicle could
tip or roll over. Always back straight
down in R (Reverse) gear and apply
brakes to control your speed.
5-12Starting and driving

You do not have to remove the start/stop
button from the ignition lock when you leave
the vehicle. You should, however, always
take the key with you when leaving the ve-
hicle. As long as the key is in the vehicle:
•The vehicle can be started using the push-
button ignition switch.
•The electrically powered equipment can be
operated.
EMERGENCY ENGINE SHUT OFF
To shut off the engine in an emergency situ-
ation while driving, perform the following
procedure:
•Rapidly push the push-button ignition
switch 3 consecutive times in less than 1.5
seconds, or
•Push and hold the push-button ignition
switch for more than 2 seconds.
•Make sure the area around the vehicle is
clear.
•Check fluid levels such as engine oil, cool-
ant, brake fluid, and windshield-washer
fluid as frequently as possible, or at least
whenever you refuel.
•Check that all windows and lights are
clean.
•Visually inspect tires for their appearance
and condition. Measure and check the tire
pressure for proper inflation.
•Check that all doors are closed.
•Position seat and adjust head restraints/
headrests.
•Adjust the inside and outside rear view
mirrors.
•Fasten your seat belt and ask all passen-
gers to do likewise.
•Check the operation of the warning lights
when the ignition switch is pushed to the
ON position.
STARTING PROCEDURE WITH
THE KEY
0OFF position
1ACC position
2ON position
3START position
1. Apply the parking brake.
2. Shift the transmission to position P (Park) by pressing the

button.
The transmission position indicator in the
vehicle information display shows

When the transmission is in position N
(Neutral), you can also start the engine
with the brake pedal depressed.
The starter is designed not to operate if the
shift lever is in any of the driving positions.
NPA1483
BEFORE STARTING ENGINE STARTING ENGINE
5-18Starting and driving

Shifting
P Park position with parking lock
R Reverse
N Neutral
D DriveTransmission position display:
NOTE
If the transmission position display in the ve-
hicle information display is not working, you
should pull away carefully to check whether
the desired transmission position IS en-
gaged. Ideally, you should select transmis-
sion position D and automatic drive program
EorS.
The shift lever indicator
1located in the
lower part of the vehicle information display
shows the current position of the transmis-
sion.
It shows the P,R,N,D modes when the trans-
mission is in auto mode or the shift position
when the transmission is in manual mode.
WARNING
Apply the parking brake if the shift lever is
in any position while the engine is not run-
ning. Failure to do so could cause the ve-
hicle to move unexpectedly or roll away
and result in serious personal injury or
property damage.
CAUTION
Use the P (Park) or R (Reverse) position
only when the vehicle is completely
stopped.NSD585NSD649
Starting and driving5-21

Holding the vehicle stationary on
uphill gradients
WARNING
If the transmission overheats, the elec-
tronic management system is automati-
cally deactivated. This interrupts the
power transmission from the engine to the
wheels. The vehicle may, for example, roll
backwards on gradients. There is a risk of
an accident. Never hold the vehicle station-
ary on uphill gradients by depressing the
accelerator.
The transmission may overheat if you hold
the vehicle stationary on uphill gradients by
depressing the accelerator pedal. If the trans-
mission overheats, a warning tone sounds
and the [Stop Vehicle Shift to P Leave Engine
Running] display message appears in the ve-
hicle information display. You will only be able
to continue your journey once the transmis-
sion has cooled down and the display mes-
sage in the vehicle information display has
disappeared. Never hold the vehicle stationary on uphill
gradients by depressing the accelerator. In-
stead, only ever hold the vehicle stationary on
uphill gradients by:•Depressing the brake pedal.
•Engaging the electric parking brake.
Kickdown
Use kickdown for maximum acceleration:
•Depress the accelerator pedal beyond the
pressure point.
The transmission shifts to a lower gear
depending on the engine speed.
•Ease off the accelerator pedal once the
desired speed is reached.
The automatic transmission shifts back up.
Drive mode switch
The drive mode switch allows you to choose
between drive programs with different driv-
ing characteristics.
Press drive mode switch
1. The selected
drive program appears in the vehicle informa-
tion display.
The automatic transmission switches to drive
program E each time the engine is started.
E (Economy): comfortable, economical driv- ing
S (Sport): sporty driving style
M (Manual): manual gear shifting
For more details of the manual drive program
see "Manual drive program" later in this sec-
tion.
NSD587
Starting and driving5-23

Steering wheel gearshift paddles
1Left steering wheel gearshift paddle
(shifts down)
2Right steering wheel gearshift paddle
(shifts up)
In drive program M, you can change gear
yourself using the steering wheel gearshift
paddles.
If you pull the left or right steering wheel
gearshift paddle when in automatic drive
program E or S, the automatic transmission
shifts into drive program M for a limited time.
Depending on which gearshift paddle is
pulled, the automatic transmission immedi-
ately shifts into the next gear down or up.
Automatic drive programs
Drive program E is characterized by the fol-
lowing:
•Comfort-oriented engine settings.
•Optimal fuel consumption resulting from
the automatic transmission shifting up
sooner.
•The vehicle pulling away more gently in
forward and reverse gears unless the ac-
celerator pedal is depressed fully.
•Increased sensitivity. This improves han-
dling on slippery road surfaces, for ex-
ample.
•The automatic transmission shifting up
sooner. This results in the vehicle being
driven at lower engine speeds and the
wheels being less likely to spin.
Drive program S is characterized by the fol-
lowing:
•Sporty engine settings.
•The automatic transmission shifting up
later.
•As a result of the later automatic transmis-
sion shift points, the fuel consumption
possibly being higher.
Manual drive program
In manual drive program M, you can change
gear yourself by using the steering wheel
gearshift paddles. For this, the transmission
must be in position D (Drive). The gear cur-
rently selected and engaged is shown in the
vehicle information display
Manual drive program M differs from drive
programs E and S with regard to spontaneity,
responsiveness and smoothness of gear
changes.
Using manual gears:
3 To use the engine's braking effect
2 To use the braking effect of the engine on downhill gradients and for driving on steep
mountain roads, in mountainous terrain or
in arduous conditions.
1 To use the braking effect of the engine on extremely steep downhill gradients and on
long downhill stretches.
NSD584
5-24Starting and driving

Activating the manual drive program:
•Permanently: Press the drive mode switch
1repeatedly until M appears in the ve-
hicle information display. Manual drive
program M remains active until drive pro-
gram E or S is engaged.
•Temporarily: Pull the right or left steering
wheel gearshift paddle (see "Steering
wheel gearshift paddles" later in this sec-
tion). Manual drive program M is tempo-
rarily active. Depending on which gearshift
paddle is pulled, the automatic transmis-
sion immediately shifts into the next gear
down or up. When manual drive program M is activated
via the steering wheel gearshift paddles, the
temporarily active manual drive program M
will be deactivated automatically after a lim-
ited time, if the driving situation permits. The
automatic transmission switches to the pre-
viously activated drive program E or S. When
driving on downhill gradients, the temporarily
active manual drive program M will only be
deactivated if the accelerator pedal is de-
pressed while the vehicle is rolling downhill.
Upshifting:
Pull the right-hand steering wheel gearshift
paddle (see "Steering wheel gearshift
paddles" earlier in this section). The auto-
matic transmission shifts up to the next gear.
In order to prevent engine damage the auto-
matic transmission automatically shifts up if
the maximum engine speed on the currently
engaged gear is reached and you depress the
accelerator pedal.
Gearshift recommendation:
The gearshift recommendations assist you in
adopting an economical driving style. The
recommended gear is shown in the vehicle
information display.
Shift to recommended gear1according to
gearshift recommendation
2when shown in
the vehicle information display.
Downshifiting:
Pull the left-hand steering wheel gearshift
paddle (see "Steering wheel gearshift
paddles" earlier in this section). The auto-
matic transmission shifts down to the next
gear.
If you slow down or stop without shifting
down, the automatic transmission automati-
cally shifts down.
NSD587NSD589
Starting and driving5-25

The Idle Stop/Start function switches the
engine off automatically if the vehicle is
stopped under certain conditions.
When pulling away again, the engine starts
automatically. The Idle Stop/Start function
thereby helps you to reduce the fuel con-
sumption and emissions of your vehicle.
WARNING
If the engine is switched off automatically
and you exit the vehicle, the engine is re-
started automatically. The vehicle may be-
gin moving There is a risk of accident and
injury.
If you wish to exit the vehicle, always turn
off the ignition and secure the vehicle
against rolling away.If the
Idle Stop/Start symbol is shown
in green in the vehicle information display, the
Idle Stop/Start function switches the engine
off automatically once the vehicle stops mov-
ing.
The Idle Stop/Start function is automatically
activated each time you start the engine with
the ignition key.
If the Idle Stop/Start function has been
manually deactivated (see "Deactivating/
activating the Idle Stop/Start function" later
in this section) or a malfunction has caused
the system to be deactivated, the
Idle
Stop/Start symbol is not displayed.
AUTOMATIC ENGINE
SWITCH-OFF
The Idle Stop/Start function is operational
and theIdle Stop/Start symbol is dis-
played in green in the vehicle information dis-
play, if:
•The indicator light in the ECO button is lit
green.
•The outside temperature is within the
range that is suitable for the system.
•The engine is at normal operating tem-
perature.
•The set temperature for the vehicle interior
has been reached.
•The battery is sufficiently charged.
•The system detects that the windshield is
not misted up when the air-conditioning
system is switched on.
•The hood is closed.
•The driver's door is closed and the driver's
seat belt is fastened.
If the conditions for automatic engine
switch-off are not all fulfilled, the
Idle
Stop/Start symbol is shown in yellow.
NSD620
Idle Stop/Start symbol
IDLE STOP/START SYSTEM (IF
EQUIPPED)
Starting and driving5-29

All of the vehicle's systems remain active
when the engine is switched off automati-
cally.
The engine can be switched off automatically
a maximum of four times (initial stop, then
three subsequent stops) in succession. The
Idle Stop/Start symbol is shown in yel-
low in the vehicle information display after
the engine has been started automatically for
the fourth time. When the
Idle Stop/
Start symbol is shown in green in the vehicle
information display, automatic engine
switch-off is again possible.
NOTE
If the hood is opened while the engine is run-
ning and the Idle Stop/Start function is op-
erational, the engine will switch off auto-
matically.
If the vehicle is brought to a standstill in D or
N, the Idle Stop/Start function switches off
the engine automatically.
AUTOMATIC ENGINE START
The engine is started automatically if:
•You switch off the Idle Stop/Start func-
tion by pressing the ECO button.
•You engage Reverse R or Drive D.
•You unfasten your seat belt or open the
driver's door.
•The vehicle starts to roll.
•The brake system requires this.
•The temperature in the vehicle interior de-
viates from the set range.
•The system detects moisture on the wind-
shield when the air-conditioning system is
switched on.
•The battery's charge status is too low.
The engine is started automatically if you:
•Release the brake pedal in transmission
position D (Drive) or N (Neutral).
•Depress the accelerator pedal.
•Move the transmission out of position P
(Park).
Shifting the transmission to position P (Park)
does not start the engine.
If you shift the transmission from R (Reverse)
to D (Drive), the Idle Stop/Start function is
available again once the
Idle Stop/
Start symbol reappears in green in the vehicle
information display.
DEACTIVATING/ACTIVATING
THE IDLE STOP/START
FUNCTION
•To deactivate: press ECO button1. Indi-
cator light
2and theIdle Stop/
Start symbol in the vehicle information dis-
play turn off.
•To activate: press ECO button1. Indica-
tor light
2lights up. If all conditions for
automatic engine switch-off (see "Auto-
matic engine switch-off" earlier in this sec-
tion) are fulfilled, the
Idle Stop/Start
symbol is shown in green in the vehicle
information display.
NIC2633
5-30Starting and driving

If not all conditions for automatic engine
switch-off are met, theIdle Stop/
Start symbol is lit yellow in the vehicle
information display. If this is the case, the
Idle Stop/Start function is not active.
If indicator light
2on ECO button1is off,
the Idle Stop/Start function has been deacti-
vated manually or as the result of a malfunc-
tion. The engine will then not be switched off
automatically when the vehicle stops.
WARNING
Failure to follow the warnings and instruc-
tions for proper use of the LDW system
could result in serious personal injury or
death. The LDW system will not steer the
vehicle or prevent loss of control. It is the
driver’s responsibility to stay alert, drive
safely, keep the vehicle in the traveling
lane, and be in control of the vehicle at all
times.
The LDW system warns the driver with a
warning light and intermittent steering vibra-
tion that the vehicle is beginning to leave the
traveling lane. The LDW system uses a camera
1installed
behind the windshield to monitor the lane
markers of your traveling lane.
NSD644
LANE DEPARTURE WARNING (LDW)
SYSTEM (IF EQUIPPED)
Starting and driving5-31

LDW SYSTEM OPERATION
1Steering wheel mounted controls
2Vehicle information display
ADisplay area
BMenu barThe LDW system operates at speeds of ap-
proximately 40 MPH (60 km/h) and above,
when the lane markings are clear.
If the system detects that the vehicle's front
wheel has passed over the lane marking, a
warning will be provided. It will warn you by
means of intermittent vibration through the
steering wheel for up to 1.5 seconds and a
visual alert.
NOTE
The LDW system is designed not to warn
when you operate the lane change signal and
change traveling lanes in the direction of the
signal.
No warning vibration occurs if you activate
the turn signals. In this event, the warnings
are suppressed for a certain period of time.
NSD626
5-32Starting and driving