warning light INFINITI QX30 2018 Repair Manual

If you lock the vehicle with the key's remote
control or with the Intelligent Key, after a
short time:
•You will not be able to switch on the igni-
tion with the push-button ignition switch.
•You will not be able to start the engine
with the push-button ignition switch until
the vehicle is unlocked again.
If you lock the vehicle centrally using the but-
ton on the front door (see "Locking with in-
side door knob" in the "3. Pre-driving checks
and adjustments" section). you can continue
to start the engine with the push-button ig-
nition switch.
KEY POSITIONS WITH THE
PUSH-BUTTON IGNITION
SWITCH
1Start/Stop button
2Ignition lock
When you switch on the ignition, all of the
indicator lights in the combination meter light
up. For further information on situations
where an indicator light either fails to go out
after starting the engine or lights up while
driving see "Warning lights, indicator lights
and audible reminders" in the "2. Instruments
and controls" section.
If the push-button ignition switch
1has not
yet been pressed, this corresponds to the key
being removed from the ignition.
To switch on the power supply (accessory
mode): press the push-button ignition switch
1once without depressing the brake pedal.
The power supply is switched on. You can
now activate the windshield wipers, for ex-
ample.
The power supply is switched off again if the
driver's door is opened and you press the
push-button ignition switch
1twice when in
this position.
To switch on the ignition: press the push-
button ignition switch
1twice without de-
pressing the brake pedal. The ignition is
switched on.
The ignition is switched off if the driver's door
is opened and you press the push-button
ignition switch
1when in this position.
REMOVING THE START/STOP
BUTTON
You can remove the start/stop button from
the ignition lock and start the vehicle as nor-
mal using the key.
You can only switch between push-button
ignition switch mode and key operation when
the vehicle is stationary.
You must also engage park position P (Park).
Remove the start/stop button
1from igni-
tion lock
2.
NPA1484
Starting and driving5-17

You do not have to remove the start/stop
button from the ignition lock when you leave
the vehicle. You should, however, always
take the key with you when leaving the ve-
hicle. As long as the key is in the vehicle:
•The vehicle can be started using the push-
button ignition switch.
•The electrically powered equipment can be
operated.
EMERGENCY ENGINE SHUT OFF
To shut off the engine in an emergency situ-
ation while driving, perform the following
procedure:
•Rapidly push the push-button ignition
switch 3 consecutive times in less than 1.5
seconds, or
•Push and hold the push-button ignition
switch for more than 2 seconds.
•Make sure the area around the vehicle is
clear.
•Check fluid levels such as engine oil, cool-
ant, brake fluid, and windshield-washer
fluid as frequently as possible, or at least
whenever you refuel.
•Check that all windows and lights are
clean.
•Visually inspect tires for their appearance
and condition. Measure and check the tire
pressure for proper inflation.
•Check that all doors are closed.
•Position seat and adjust head restraints/
headrests.
•Adjust the inside and outside rear view
mirrors.
•Fasten your seat belt and ask all passen-
gers to do likewise.
•Check the operation of the warning lights
when the ignition switch is pushed to the
ON position.
STARTING PROCEDURE WITH
THE KEY
0OFF position
1ACC position
2ON position
3START position
1. Apply the parking brake.
2. Shift the transmission to position P (Park) by pressing the

button.
The transmission position indicator in the
vehicle information display shows

When the transmission is in position N
(Neutral), you can also start the engine
with the brake pedal depressed.
The starter is designed not to operate if the
shift lever is in any of the driving positions.
NPA1483
BEFORE STARTING ENGINE STARTING ENGINE
5-18Starting and driving

WARNING
•Be sure the parking brake is fully re-
leased before driving. Failure to do so
can cause brake failure and lead to an
accident.
•Do not release the parking brake from
outside the vehicle.
•Do not use the shift lever in place of the
parking brake. When parking, be sure
the parking brake is fully engaged.
•To help avoid risk of injury or death
through unintended operation of the
vehicle and/or its systems, do not leave
children, people who require the assis-
tance of others, or pets unattended in
your vehicle. Additionally, the tempera-
ture inside a closed vehicle on a warm
day can quickly become high enough to
cause a significant risk of injury or death
to people and pets. The function of the electric parking brake is
dependent on the on-board voltage. If the
on-board voltage is low or if there is a mal-
function in the system, it may not be possible
to apply the released parking brake. If this is
the case:
•Only park the vehicle on level ground and
secure it to prevent it from rolling away.
•Shift the automatic transmission to posi-
tion P (Park).
•It is recommended you contact an
INFINITI retailer.
It may not be possible to release an applied
parking brake if the on-board voltage is low
or if there is a malfunction in the system. It is
recommended you contact an INFINITI re-
tailer.
The electric parking brake carries out a func-
tion check at regular intervals when the en-
gine is switched off. Noises that occur are
normal.APPLYING/RELEASING
MANUALLY
The electric parking brake can be applied or
released by operating the parking brake
handle
1.
To apply: Push handle
1.
When the electric parking brake is applied,
the red
indicator light lights up in the
combination meter.
The electric parking brake can also be applied
when the ignition switch is in the OFF posi-
tion or the key is removed.
To release: With the ignition switch in the ON
position, pull handle
1.
NPA1485
PARKING BRAKE
Starting and driving5-27

Before driving, check that the brake warning
lightgoes out. For additional informa-
tion, see "Warning lights, indicator lights and
audible reminders" in the "2. Instruments and
controls" section.
The electric parking brake can only be re-
leased when the ignition switch is in the ON
position.
APPLYING AUTOMATICALLY
(VEHICLES WITH AUTOMATIC
TRANSMISSION)
The electric parking brake is automatically
applied when:
•Intelligent cruise control (if equipped)
brings the vehicle to a standstill.
or
•Intelligent Parking Assist (if equipped) is
keeping the vehicle stationary.
The red
indicator light lights up in the
combination meter.
The electric parking brake is not automati-
cally applied if the engine is switched off by
the Idle Stop/Start function.
RELEASING AUTOMATICALLY
The electric parking brake can only be re-
leased automatically in vehicles with auto-
matic transmission.
The electric parking brake of your vehicle is
released automatically when all of the fol-
lowing conditions are fulfilled:
•The engine is running.
•The transmission is in position D (Drive) or
R (Reverse).
•The seat belt is fastened.
•You depress the accelerator pedal.
If the transmission is in position R, the lift
gate must be closed.
If your seat belt is not fastened, the following
conditions must be fulfilled to automatically
release the electric parking brake:
•The driver's door is closed
•You have shifted out of transmission posi-
tion P (Park) or you have previously driven
faster than 2 MPH (3 km/h).
Ensure that you do not depress the accelera-
tor pedal unintentionally. Otherwise, the
parking brake will be released and the vehicle
will start to move.
EMERGENCY BRAKING
The vehicle can also be braked during an
emergency by using the electric parking
brake.
While driving, push handle
1of the electric
parking brake. The vehicle is braked as long as
you keep handle
1of the electric parking
brake pressed. The longer the electric parking
brake handle
1is depressed, the greater the
braking force.
During braking:
•A warning tone sounds.
•The [Please Release Parking Brake] mes-
sage appears.
•The redindicator light in the combi-
nation meter flashes.
When the vehicle has been braked to a stand-
still, the electric parking brake is applied.
5-28Starting and driving

The Idle Stop/Start function switches the
engine off automatically if the vehicle is
stopped under certain conditions.
When pulling away again, the engine starts
automatically. The Idle Stop/Start function
thereby helps you to reduce the fuel con-
sumption and emissions of your vehicle.
WARNING
If the engine is switched off automatically
and you exit the vehicle, the engine is re-
started automatically. The vehicle may be-
gin moving There is a risk of accident and
injury.
If you wish to exit the vehicle, always turn
off the ignition and secure the vehicle
against rolling away.If the
Idle Stop/Start symbol is shown
in green in the vehicle information display, the
Idle Stop/Start function switches the engine
off automatically once the vehicle stops mov-
ing.
The Idle Stop/Start function is automatically
activated each time you start the engine with
the ignition key.
If the Idle Stop/Start function has been
manually deactivated (see "Deactivating/
activating the Idle Stop/Start function" later
in this section) or a malfunction has caused
the system to be deactivated, the
Idle
Stop/Start symbol is not displayed.
AUTOMATIC ENGINE
SWITCH-OFF
The Idle Stop/Start function is operational
and theIdle Stop/Start symbol is dis-
played in green in the vehicle information dis-
play, if:
•The indicator light in the ECO button is lit
green.
•The outside temperature is within the
range that is suitable for the system.
•The engine is at normal operating tem-
perature.
•The set temperature for the vehicle interior
has been reached.
•The battery is sufficiently charged.
•The system detects that the windshield is
not misted up when the air-conditioning
system is switched on.
•The hood is closed.
•The driver's door is closed and the driver's
seat belt is fastened.
If the conditions for automatic engine
switch-off are not all fulfilled, the
Idle
Stop/Start symbol is shown in yellow.
NSD620
Idle Stop/Start symbol
IDLE STOP/START SYSTEM (IF
EQUIPPED)
Starting and driving5-29

If not all conditions for automatic engine
switch-off are met, theIdle Stop/
Start symbol is lit yellow in the vehicle
information display. If this is the case, the
Idle Stop/Start function is not active.
If indicator light
2on ECO button1is off,
the Idle Stop/Start function has been deacti-
vated manually or as the result of a malfunc-
tion. The engine will then not be switched off
automatically when the vehicle stops.
WARNING
Failure to follow the warnings and instruc-
tions for proper use of the LDW system
could result in serious personal injury or
death. The LDW system will not steer the
vehicle or prevent loss of control. It is the
driver’s responsibility to stay alert, drive
safely, keep the vehicle in the traveling
lane, and be in control of the vehicle at all
times.
The LDW system warns the driver with a
warning light and intermittent steering vibra-
tion that the vehicle is beginning to leave the
traveling lane. The LDW system uses a camera
1installed
behind the windshield to monitor the lane
markers of your traveling lane.
NSD644
LANE DEPARTURE WARNING (LDW)
SYSTEM (IF EQUIPPED)
Starting and driving5-31

SYSTEM MAINTENANCE
The lane camera unit1for the LDW system
is located above the inside mirror.
To ensure the proper operation of the LDW
system and prevent a system malfunction, be
sure to observe the following:
•Always keep the windshield clean.
•Do not attach a sticker (including transpar-
ent material) or install an accessory near
the camera unit.
•Do not place reflective materials, such as
white paper or a mirror, on the instrument
panel. The reflection of sunlight may ad-
versely affect the camera unit’s capability
of detecting the lane markers.
•Do not strike or damage the areas around
the camera unit. Do not touch the camera
lens or remove parts from the camera unit.
If the camera unit is damaged due to an
accident, it is recommended you contact
an INFINITI retailer.WARNING
Failure to follow the warnings and instruc-
tions for proper use of the BSW system
could result in serious injury or death.
•The Blind Spot Warning (BSW) system
is not a replacement for proper driving
procedure and is not designed to pre-
vent contact with vehicles or objects.
When changing lanes, always use the
side and rear mirrors and turn and look in
the direction you will move to ensure it is
safe to change lanes. Never rely solely
on the BSW system.
The Blind Spot Warning (BSW) system can
help alert the driver of other vehicles in adja-
cent lanes when changing lanes.
NSD644
BLIND SPOT WARNING (BSW)
SYSTEM (IF EQUIPPED)
5-36Starting and driving

Illustration 2:If the turn signal is then acti-
vated, the system chimes (twice) and the
BSW indicator light flashes. The BSW indica-
tor light continues to flash until the detected
vehicles leave the detection zone.
NOTE
•The BSW indicator lights illuminate for a
few seconds when the ignition switch is
placed in the ON position.
•The brightness of the BSW indicator lights
is adjusted automatically depending on the
brightness of the ambient light.
•If a vehicle comes into the detection zone
after the driver activates the turn signal,
then only the BSW indicator light flashes
and no chime sounds. (See "Another ve-
hicle approaching from behind" later in this
section.)
A chime sounds if the radar sensors have
already detected vehicles when the driver ac-
tivates the turn signal.
WARNING
•Do not use the BSW system when tow-
ing a trailer because the system may not
function properly.
•Excessive noise (for example audio sys-
tem volume, open vehicle window) will
interfere with the chime sound, and it
may not be heard.
•The radar sensors may not be able to
detect and activate BSW when certain
objects are present such as: – Pedestrians, bicycles, animals
– Several types of vehicles such as mo-
torcycles
– Oncoming vehicles
– Vehicles remaining in the detection
zone when you accelerate from a
stop. –
A vehicle merging into an adjacent
lane at a speed approximately the
same as your vehicle.
– A vehicle approaching rapidly from
behind.
– A vehicle which your vehicle over-
takes rapidly.
•Severe weather or road spray conditions
may reduce the ability of the radar to
detect other vehicles.
•The radar sensors detection zone is de-
signed based on a standard lane width.
When driving in a wider lane, the radar
sensors may not detect vehicles in an
adjacent lane. When driving in a narrow
lane, the radar sensors may detect ve-
hicles driving two lanes away.
•The radar sensors are designed to ignore
most stationary objects, however ob-
jects such as guardrails, walls, foliage
and parked vehicles may occasionally be
detected. This is a normal operating
condition.
SSD1031Z
Illustration 2
Starting and driving5-39

–Vehicles such as motorcycles, low
height vehicles, or high ground clear-
ance vehicles.
– Oncoming vehicles.
– Vehicles remaining in the detection
zone when you accelerate from a
stop.
– A vehicle merging into an adjacent
lane at a speed approximately the
same as your vehicle.
– A vehicle that is too close to your
vehicle.
– A vehicle approaching rapidly from
behind.
– A vehicle which your vehicle over-
takes rapidly.
•The radar sensors detection zone is de-
signed based on a standard lane width.
When driving in a wider lane, the radar
sensors may not detect vehicles in an
adjacent lane. When driving in a narrow
lane, the radar sensors may detect ve-
hicles driving two lanes away.
•The radar sensors are designed to ignore
most stationary objects, however ob-
jects such as guardrails, walls, foliage
and parked vehicles may occasionally be
detected. This is a normal operating
condition.
•The following conditions may reduce the
ability of the radar to detect other ve-
hicles: – Severe weather
– Road spray
– Ice/frost/dirt build-up on the vehicle
•Do not attach stickers (including trans-
parent material), install accessories or
apply additional paint near the radar
sensors. These conditions may reduce
the ability of the radar to detect other
vehicles.
•Do not use the BSW system when tow-
ing a trailer because the system may not
function properly.
•Excessive noise (e.g. audio system vol-
ume, open vehicle window) will interfere
with the chime sound, and it may not be
heard.
•The BSW system may not provide a
warning for vehicles that pass through
the detection zone quickly.
Another vehicle approaching from
behind
Illustration 1: The BSW indicator light illumi-
nates if a vehicle enters the detection zone
from behind in an adjacent lane.
However, if the overtaking vehicle is travel-
ling much faster than your vehicle, the indica-
tor light may not illuminate before the de-
tected vehicle is beside your vehicle. Always
use the side and rear mirrors and turn and
look in the direction your vehicle will move to
ensure it is safe to change lanes.
SSD1026Z
Illustratio n 1 – Approaching from behind
Starting and driving5-41

Illustration 2: If the driver activates the turn
signal, then the system chimes (twice) and the
BSW indicator light flashes.
NOTE
•The radar sensors may not detect vehicles
which are approaching rapidly from be-
hind.
•If the driver activates the turn signal be-
fore a vehicle enters the detection zone,
the BSW indicator light will flash but no
chime will sound when the other vehicle is
detected.
Accelerate from a stop
NOTE
Illustration 3: If you accelerate from a stop
with a vehicle in the detection zone, the
other vehicle may not be detected.
Overtaking another vehicle
When you overtake a vehicle, the warning
only occurs if the difference in speed is less
than 7 MPH (12 km/h).
Illustration 4: The side indicator light illumi-
nates if you overtake a vehicle and that ve-
hicle stays in the detection zone for approxi-
mately 3 seconds.
SSD1031Z
Illustratio n 2 – Approaching from behind
SSD1032Z
Illustration3–Acceleratefromastop
SSD1033Z
Illustration 4 – Overtaking another vehicle
5-42Starting and driving