mirror controls INFINITI QX30 2018 Owners Manual

1. Rear armrest* (P.1-7)
2. Rear personal lights (P.2-87)
3. Overhead control panel (P.2-76)
4. Sunshade switch* (P.2-76)
5. Sun visor (P.2-18)
6. Security system buttons (P.3-59)
7. Interior rear-view mirror (P.3-18)8. Door handle (P.3-6)
9. Door armrest
— Power windows controls (P.2-73)
— Exterior rear view mirror remote control
switch (P.2-18)
10. Front cup holders (P.2-80)
11. Air conditioner controls (P.4-43) 12. Glove box/storage (P.2-79)
*: if equipped
NIC2701
PASSENGER COMPARTMENT
Illustrated table of contents0-5

2 Instruments and controls
Cockpit........................... .2-2
Instrument panel ..................... .2-3
Meters and gauges .................... .2-4
Speedometer and odometer .............2-4
Outside temperature display .............2-5
Tachometer ...................... .2-6
Engine coolant temperature gauge .........2-6
Fuel gauge ....................... .2-7
Warning lights, indicator lights and audible
reminders .......................... .2-8
Checking lights .................... .2-8
Warning lights ..................... .2-8
Indicator lights .................... .2-13
Audible reminders .................. .2-14
Vehicle information display ...............2-15
Menus and submenus ............... .2-16
Display Messages .................. .2-29
Security system ..................... .2-59
Immobiliser ...................... .2-59
Anti-theft alarm system (if equipped) .......2-59
Wiper and washer switch ................2-60
Switching the windshield wipers on/off .....2-61
Switching the rear window wiper on/off . . . .2-62
Rear window and outside mirror defroster
switch ........................... .2-63
Windshield de-icer switch (if equipped) .......2-63
Headlight and turn signal switches ..........2-64Headlight switch
.................. .2-64
Combination switch ................ .2-66
Adaptive front lighting system
(LED headlight only) (if equipped) .........2-67
High beam assist (LED headlight only) ......2-68
Headlights misted up on the inside ........2-70
Instrument brightness control ...........2-70
Fog light switch (If so equipped) ............2-70
Front fog lights ................... .2-70
Rear fog light ..................... .2-71
Horn ............................ .2-71
Seat
heating (if equipped) ............... .2-72
Windows ......................... .2-73
Power windows ................... .2-73
Fixed glass roof (if equipped) ..............2-76
Sunshade operation ................ .2-76
Clock ............................ .2-77
Adjusting time .................... .2-77
Power outlet ....................... .2-78
Storage .......................... .2-79
Glove box ....................... .2-79
Front console compartment ............2-79
Console box ..................... .2-80
Card holder ...................... .2-80
Cup holders ..................... .2-80
Coat hooks ...................... .2-81
Cargo tie-down hooks ............... .2-81

Setting the brightness of the ambient light-
ing:
1. Press the
orbutton on the
steering wheel to select the [Settings]
menu.
2. Press the
orbutton to select
[Light] submenu.
3. Press to confirm.
4. Press the
orbutton to select
the [Ambient Light Brightness] function.
You will see the selected setting.
5. Change the setting with . If you change the setting, conversion does
not take place until the next time the ve-
hicle is stationary.
6. Press the
orbutton to adjust
the brightness to a level from [Off] to
[Level 5] (bright).
7. Press the or
button to save the
setting. Activating/deactivating the surround
lighting and exterior lighting delayed
switch-off:
If you have activated the Surround lighting
function and the light switch is set to
, the following functions are acti-
vated when it is dark:
•Surround lighting: the exterior lighting re-
mains lit for 40 seconds after unlocking
with the key. If you start the engine, the
surround lighting is switched off and auto-
matic headlight mode is activated .
•Exterior lighting delayed switch-off: the
exterior lighting remains lit for 60 seconds
after the engine is switched off. If you
close all the doors and the lift gate, the
exterior lighting goes off after 15 seconds.
1. Press the
orbutton on the
steering wheel to select the [Settings]
menu.
2. Press the
orbutton to select
[Light] submenu.
3. Press to confirm.
4. Press the
orbutton to select
the [Surround Lighting] function.
5. Press the button to save the setting. When the [Surround Lighting] function is
activated, the light cone and the area around the vehicle are displayed in orange
in the vehicle information display
6. Press the button to confirm the set- ting.
Deactivating delayed switch-off of the exte-
rior lighting temporarily:
1. Before leaving the vehicle, switch the igni- tion switch to the OFF position.
2. Switch the ignition switch to the ON po- sition.
The exterior lighting delayed switch-off is
deactivated.
Delayed switch-off of the exterior lighting is
reactivated the next time you start the en-
gine.
Depending on your vehicle's equipment,
when the surround lighting and delayed
switch-off exterior lighting are on, the fol-
lowing light up:
•Side lights
•Fog lights
•Low beam headlights
•Daytime driving lights
•Surround lighting in the exterior mirrors
Instruments and controls2-27

Activating/deactivating the interior light-
ing delay:
If you activate the [Interior Lighting Delay]
function, the interior lighting remains on for
20 seconds after you remove the key from
the ignition lock.
1. Press the
orbutton on the
steering wheel to select the [Settings]
menu.
2. Press the
orbutton to select
[Light] submenu.
3. Press to confirm.
4. Press the
orbutton to select
the [Interior Lighting Delay] function. If
the [Interior lighting delayed switch-off]
function has been switched on, the vehicle
interior is displayed in orange in the ve-
hicle information display
5. Press the button to save the setting.
Vehicle
Setting permanent speed limiter:
You can set permanent speed limiter using
the [Limit Speed (Winter Tires)] function.
1. Press the
orbutton on the
steering wheel to select the [Settings]
menu. 2. Press the
orbutton to select
[Vehicle] submenu.
3. Press to confirm.
4. Press the
orbutton to select
the [Limit Speed (Winter Tires)] function.
You will see the selected setting.
5. Press to confirm.
6. Press the
orbutton to adjust
permanent speed limiter in increments of
ten ([150 mph] to [100 mph]), [240
km/h] to [160 km/h]). The [Off] setting
switches permanent speed limiter off).
7. Press the or
button to store
the entry.
Activating/deactivating the acoustic lock-
ing confirmation:
If you switch on the [Acoustic Lock Feed-
back] function, an acoustic signal sounds
when you lock the vehicle.
1. Press the
orbutton on the
steering wheel to select the [Settings]
menu.
2. Press the
orbutton to select
[Vehicle] submenu.
3. Press to confirm. 4. Press the
orbutton to select
the [Acoustic Lock Feedback] function.
If the [Acoustic Lock Feedback] function
is activated, the
symbol in the ve-
hicle information display lights up orange.
5. Press the button to save the setting.
Convenience
Switching the [Fold Mirrors in when Lock-
ing] function on/off:
This function is only available when the ve-
hicle is equipped with the electrical fold-in
function.
When you activate the [Fold Mirrors in when
Locking] function, the exterior mirrors are
folded in when the vehicle is locked. If you
unlock the vehicle and then open the driver's
or front passenger door, the exterior mirrors
fold out again.
If you have switched on the [Fold Mirrors in
when Locking] function and you fold in the
exterior mirrors using the button on the door
(see "Folding" in the "3. Pre-driving checks
and adjustments" section), they will not fold
out automatically. The exterior mirrors can
then only be folded out using the button on
the door.
2-28Instruments and controls

1. Press theorbutton on the
steering wheel to select the [Settings]
menu.
2. Press the
orbutton to select
[Convenience] submenu.
3. Press to confirm.
4.
Press theorbutton to select the
[Fold Mirrors in when Locking] function.
If the [Fold Mirrors in when Locking]
function is activated, the vehicle's exterior
mirror is shown in orange in the vehicle
information display.
5. Press the button to save the setting.
Resetting to factory settings
1.Press theorbutton on the
steering wheel to select the [Settings] menu.
2. Press theorbutton to select
[Factory Setting] submenu.
3. Press to confirm.
The [Reset All Settings?] message appears.
4. Press theorbutton to select
[No] or [Yes].
5.
ress the button to confirm the selec-
tion.
If you have selected [Yes], the vehicle in-
formation display shows a confirmation
message. For safety reasons, not all functions are reset:
the [Limit Speed (Winter Tires)] function in
permanent speed limiter can only be set in the
[Vehicle] submenu.
If you want to reset the Daytime driving lights
function in the Lights submenu, you must switch
the ignition switch to the ACC position.
DISPLAY MESSAGES
Display messages appear in the vehicle infor-
mation display.
Display messages with graphic symbols are
simplified in the Owner's Manual and may
differ from the symbols in the vehicle infor-
mation display.
Certain display messages are accompanied
by an audible warning tone or a continuous
tone.
When the ignition is switched off, all display
messages are deleted apart from some high-
priority display messages. Once the causes of
the high-priority display messages have been
rectified, these display messages are deleted as
well.
When you stop and park the vehicle, please
observe the notes on parking (see "Parking" in
the "5. Starting and driving" section).
Hiding display messages
Press the orbutton to hide the
display message. The display message is hid-
den.
The vehicle information display shows high-
priority display messages in red. Some high-
priority display messages cannot be hidden.
The vehicle information display shows these
messages continuously until the causes for
the messages have been remedied.
Message memory
The vehicle information display saves certain
messages in the message memory. You can
call up these display messages:
1. Press the
orbutton on the
steering wheel to select the [Service]
menu.
If there are display messages, the vehicle
information display shows [2 messages],
for example.
2. Press the
orbutton to select
the entry, e.g. [2 messages].
3. Press to confirm.
4. Press the
orbutton to scroll
through the display messages.
Instruments and controls2-29

Driving systems
MessagePossible causes/consequences and solutions
[Lane Departure Warning
Currently Unavailable See
Operator's Manual] Lane Departure Warning is deactivated and temporarily inoperative.
Possible causes:
•The windshield is dirty in the camera's field of vision.•Visibility is impaired due to heavy rain, snow or fog.•There have been no lane markings for an extended period.•The lane markings are worn, dark or covered, e.g. by dirt or snow.
Once the causes listed above no longer apply, the display message goes out.
Lane Departure Warning is operational again.
If the display message does not disappear:
1. Pull over and stop the vehicle safely as soon as possible, paying attention to road and traffic conditions, and switch off the engine.
2. Secure the vehicle against rolling away.
3. Clean the windshield
[Lane Departure Warning
Inoperative] Lane Departure Warning is faulty.
Have the system checked. It is recommended you visit an INFINITI retailer for this service.
[Blind Spot Warning Cur-
rently Unavailable See Op-
erator's Manual] Blind Spot Warning is temporarily inoperative. Possible causes:
•The function is impaired due to heavy rain or snow.•The radar sensor system is temporarily inoperative, e.g. due to electromagnetic radiation emitted by nearby TV or radio stations
or other sources of electromagnetic radiation.
•The radar sensor system is outside the operating temperature range.
The yellow indicator lights also light up in the exterior mirrors.
Once the causes listed above no longer apply, the display message goes out.
Blind Spot Warning is operational again.
If the display message does not disappear:
1. Pull over and stop the vehicle safely as soon as possible, paying attention to road and traffic conditions, and switch off the engine.
2. Secure the vehicle against rolling away.
3. Restart the engine
2-48Instruments and controls

The defroster switchBoperates when the
ignition switch is in the ON position for the
rear window, and (if equipped) for the outside
rear view mirrors.
The defroster is used to reduce the moisture,
fog or frost on the rear window surface and
on the outside mirror surface to improve the
rear view.
When the defroster switch
is pushed,
the indicator light illuminates and the de-
froster operates for several minutes. After
the preset time has passed, the defroster will
turn off automatically. To turn off the de-
froster manually, push the defroster switch
again, and the indicator light turns off.
CAUTION
•When cleaning the inner side of the rear
window, be careful not to scratch or
damage the rear window defroster.
•When operating the defroster continu-
ously, be sure to start the engine. Oth-
erwise, it may cause the battery to dis-
charge.
•When cleaning the inner side of the win-
dow, be careful not to scratch or dam-
age the electrical conductors on the sur-
face of the window. The windshield de-icer switch (defogger
switch)
Aoperates when the ignition switch
is in the ON position.
You can use this function to defrost the wind-
shield or to demist the inside of the wind-
shield and the side windows
NOTE
You should only select the windshield de-icer
function until the windshield is clear again.
When the switch
is pushed, the indica-
tor light in the switch illuminates. The climate
control system switches to the following
functions:
•High airflow
•High temperature
•Air distribution to the windshield and front
side windows
•Air recirculation mode off
NAA1659NAA1659
REAR WINDOW AND OUTSIDE
MIRROR DEFROSTER SWITCH WINDSHIELD DE-ICER SWITCH (IF
EQUIPPED)
Instruments and controls2-63

–When a sign or mirror-like surface is
reflecting intense light towards the
front of the vehicle.
– When the container, etc. being towed
by a leading vehicle is reflecting in-
tense light.
– When a headlight on your vehicle is
damaged or dirty.
– When the vehicle is leaning at an
angle due to a punctured tire, being
towed, etc.
•The timing of switching the low beam
and high beam may change under the
following situations. –
The brightness of the headlights of the
oncoming vehicle or leading vehicle.
–The movement and direction of the on-
coming vehicle and the leading vehicle.
– When only one light on the oncoming
vehicle or the leading vehicle is illumi-
nated.
–
When the oncoming vehicle or the lead-
ing vehicle is a two-wheeled vehicle.
– Road conditions (incline, curve, the
road surface, etc.).
– The number of passengers and the
amount of luggage.
•High beam Assist does not recognize
road users: – Who have no lights, e.g. pedestrians. –
Who have low intensity lighting, e. g.
cyclists.
– Whose lighting is blocked, e.g. by a
barrier.
•In very rare cases, High beam Assist rec-
ognizes road users too late or not at all.
In this, or in similar situations, the auto-
matic high beam headlights will not be
deactivated or activated regardless.
There is a risk of an accident.
•Always carefully observe the traffic
conditions and switch off the high beam
headlights in good time.
CAUTION
High beam Assist cannot compensate for
road and weather circumstances while
driving. The system saves the driver from
having to operate the switch. The driver
always remains responsible for choosing
the correct light setting.
Specific situations in which to operate the
headlight switch manually:
•In heavy rain, snowy conditions. (gen-
eral poor visibility and bad weather con-
ditions).
•When the vehicle sensors are dirty, cov-
ered or broken.
Switching High Beam Assist on/off
To switch on:
Turn the light switch to and press
the combination switch beyond the pressure
point in the direction of arrow
3. Theindicator light in the vehicle information dis-
play lights up when it is dark and the light
sensor switches on the low-beam headlights.
If you are driving at speeds above approxi-
mately 28 MPH (45 km/h) the headlight
range is set automatically depending on the
distance between the vehicle and other road
users.
If you are driving at speeds above approxi-
mately 34 MPH (55 km/h) and no other road
users are detected, the high beam headlights
are switched on automatically. The
NIC2618
Instruments and controls2-69

The interior lighting automatically switches
on if you:
•Unlock the vehicle
•Open a door
•Remove the key from the ignition lock.
The interior lighting is activated for a short
time when the key is removed from the igni-
tion lock. You can activate this delayed
switch-off using the vehicle information dis-
play (see "Activating/deactivating the interior
lighting delay" earlier in this section).
REAR READING LIGHTS
(IF EQUIPPED)
1Switches the left hand reading light on/
off
2Switches the right hand reading light on/
off
REAR ROOM LIGHT
(IF EQUIPPED)
The rear room light (without switches) can be
switched on and off using the front overhead
control panel.
VANITY MIRROR LIGHTS
To access the vanity mirror, pull the sun visor
down and flip open the mirror cover.
The vanity mirror light illuminates when the
vanity mirror cover is opened. When the cover
is closed, the light will turn off.
LUGGAGE COMPARTMENT LIGHT
The light illuminates while the lift gate is
opened. When the lift gate is closed, the light
will turn off.
BATTERY SAVER SYSTEM
The interior light will automatically turn off
after a period of time when the ignition
switch has been put in the OFF position. To
turn on the light again, put the ignition switch
in the ON position.
NIC2632SIC3869Z
Instruments and controls2-87

The HomeLink® Universal Transceiver, inte-
grated in the vehicle's inside rear view mirror,
provides a convenient way to consolidate the
functions of up to three individual hand-held
transmitters into one built-in device.
HomeLink® Universal Transceiver:
•Will operate most Radio Frequency (RF)
devices such as garage doors, gates, home
and office lighting, entry door locks and
security systems.
•Is powered by your vehicle’s battery. No
separate batteries are required. If the ve-
hicle’s battery is discharged or is discon-
nected, HomeLink® will retain all pro-
gramming.
When the HomeLink® Universal Transceiver
is programmed, retain the original transmit-
ter for future programming procedures (Ex-
ample: new vehicle purchases). Upon sale of
the vehicle, the programmed HomeLink®
Universal Transceiver buttons should be
erased for security purposes. For additional
information, refer to "Programming
HomeLink® " later in this section.
WARNING
•Do not use the HomeLink® Universal
Transceiver with any garage door
opener that lacks safety stop and re-
verse features as required by federal
safety standards. (These standards be-
came effective for opener models manu-
factured after April 1, 1982). A garage
door opener which cannot detect an ob-
ject in the path of a closing garage door
and then automatically stop and re-
verse, does not meet current federal
safety standards. Using a garage door
opener without these features increases
the risk of serious injury or death.
•During the programming procedure
your garage door or security gate will
open and close (if the transmitter is
within range). Make sure that people or
objects are clear of the garage door,
gate, etc. that you are programming.
•Your vehicle’s engine should be turned
off while programming the HomeLink®
Universal Transceiver. NOTE
Certain garage door drives are incompatible
with the integrated garage door opener. If
you have difficulty programing the inte-
grated garage door opener, it is recom-
mended you contact your INFINITI retailer.
PROGRAMMING HOMELINK®
If you have any questions or are having diffi-
culty programming your HomeLink® but-
tons, refer to the HomeLink® web site at:
www.homelink.com or call
1-800-355-3515.
HOMELINK® UNIVERSAL
TRANSCEIVER (IF EQUIPPED)
2-88Instruments and controls