display INFINITI QX30 2019 Owner's Manual

Tire Pressure Monitoring System
warning messages
If the tire pressure monitor detects a pressure
loss in one or more tires, a warning message
is shown in the vehicle information display
and the yellow tire pressure monitor warning
light comes on.
•If the [Please Correct Tire Pressure] (yel-
low) message appears in the vehicle infor-
mation display, the tire pressure in at least
one tire is too low and must be corrected
at the next opportunity. If the system de-
tects that new sensors have been fitted
(IDs do not match those stored, and the
pressure is not feasible, or is less than 14%
under the norm then the [Please Correct
Tire Pressure] message will be displayed in
white.
•If the [Check Tires] (red) message appears
in the vehicle information display, the tire
pressure in one or more tires has dropped
significantly and the tires must be checked.
•If the [Warning Tire Malfunction] (red)
message appears in the vehicle informa-
tion display, the tire pressure in one or
more tires has dropped suddenly and the
tires must be checked.
•If the [Tire Press. Sensor(s) Missing] mes-
sage appears in the vehicle information
display, one or more sensors are missing or
cannot be detected. This could be the re-
sult of fitting a replacement wheel/tire.
Observe the instructions and safety notes in
the display messages in the vehicle informa-
tion display.
If the wheel positions on the vehicle are inter-
changed, the tire pressures may be displayed
for the wrong positions for a short time. After
a few minutes of driving, this is rectified and
the tire pressures are displayed for the cor-
rect positions.
Restarting TPMS
To keep the TPMS functioning properly, the
restart operation must be performed in the
following cases:
•When the tire pressure is adjusted
•When a tire or a wheel is replaced
•When the tires are rotated
When you restart the tire pressure monitor,
all existing warning messages are deleted
and the warning lights go out. The monitor
uses the currently set tire pressures as the
reference values for monitoring. In mostcases, the tire pressure monitor will auto-
matically detect the new reference values af-
ter you have changed the tire pressure. How-
ever, you can also define reference values
manually as described here. The tire pressure
monitor then monitors the new tire pressure
values.
Perform the following procedures to restart
the TPMS.
NOTE
Before restarting, make sure that the tire
pressures are set properly on all four tires for
the respective operating conditions. The
recommended tire pressures can be found in
the tire pressure placard on the driver' door
pillar.
1. Make sure that the ignition switch is in the
ON position.
2. Press the
orbutton on the
steering wheel to select the [Serv.] menu.
3. Press the
orbutton to select
[Tire Pressure].
4. Press to confirm.
The vehicle information display shows the
current tire pressure for each tire or the
[Tire pressures will be displayed after
driving a few minutes] message.
Starting and driving5-7

If you wish to confirm the restart:
5. Press to confirm.
The [Tire Press. Monitor Restarted] mes-
sage appears in the vehicle information
display.
After you have driven for a few minutes,
the system checks whether the current
tire pressures are within the specified
range The new tire pressures are then
accepted as reference values and moni-
tored
If you wish to cancel the restart:
6. Press the
button.
The tire pressure values stored at the last
restart will continue to be monitored
FCC Notice:
For USA:
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) This device may not
cause harmful interference, and (2) this de-
vice must accept any interference received,
including interference that may cause unde-
sired operation.NOTE
Changes or modifications not expressly ap-
proved by the party responsible for compli-
ance could void the user’s authority to oper-
ate the equipment.
For Canada:
This device complies with Industry Canada
license-exempt RSS standard(s). Operation
is subject to the following two conditions: (1)
this device may not cause interference, and
(2) this device must accept any interference,
including interference that may cause unde-
sired operation of the device.ON PAVEMENT AND OFF-ROAD
DRIVING PRECAUTIONS
Utility vehicles have a significantly higher
rollover rate than other types of vehicles.
They have higher ground clearance than pas-
senger cars to make them capable of per-
forming in a variety of on-pavement and off-
road applications. This gives them a higher
center of gravity than ordinary vehicles. An
advantage of higher ground clearance is a
better view of the road, allowing you to an-
ticipate problems. However, they are not de-
signed for cornering at the same speeds as
conventional 2-wheel drive vehicles any more
than low-slung sports cars are designed to
perform satisfactorily under off-road condi-tions. If at all possible, avoid sharp turns at
high speeds. As with other vehicles of this
type, failure to operate this vehicle correctly
may result in loss of control or vehicle roll-
over. In a rollover crash, an unbelted person is
significantly more likely to die than a person
wearing a seat belt.
For additional information, refer to "Driving
safety precautions" later in this section.
AVOIDING COLLISION AND
ROLLOVER
WARNING
Failure to operate this vehicle in a safe and
prudent manner may result in loss of con-
trol or an accident.
Be alert and drive defensively at all times.
Obey all traffic regulations. Avoid excessive
speed, high speed cornering, or sudden steer-
ing maneuvers, because these driving prac-
tices could cause you to lose control of your
vehicle.
As with any vehicle, loss of control could re-
sult in a collision with other vehicles or ob-
jects or cause the vehicle to roll over, par-
ticularly if the loss of control causes the
vehicle to slide sideways.Be attentive at all
times, and avoid driving when tired. Never
5-8Starting and driving

2. Maintain a firm grip on the steering wheel
with both hands and try to hold a straight
course.
3. When appropriate, slowly release the ac-
celerator pedal to gradually slow the ve-
hicle.
4. Gradually steer the vehicle to a safe loca-
tion off the road and away from traffic if
possible.
5. Lightly apply the brake pedal to gradually
stop the vehicle.
6. Turn on the hazard warning flashers and
contact a roadside emergency service to
change the tire. For additional informa-
tion, refer to "Flat tire".
DRINKING ALCOHOL/DRUGS
AND DRIVING
WARNING
Never drive under the influence of alcohol
or drugs. Alcohol in the bloodstream re-
duces coordination, delays reaction time
and impairs judgement. Driving after
drinking alcohol increases the likelihood of
being involved in an accident injuring your-
self and others. Additionally, if you are in-
jured in an accident, alcohol can increase
the severity of the injury.INFINITI is committed to safe driving. How-
ever, you must choose not to drive under the
influence of alcohol. Every year thousands of
people are injured or killed in alcohol-related
accidents. Although the local laws vary on
what is considered to be legally intoxicated,
the fact is that alcohol affects all people dif-
ferently and most people underestimate the
effects of alcohol.
Remember, drinking and driving don’t mix!
And that is true for drugs, too (over-the-
counter, prescription, and illegal drugs). Don’t
drive if your ability to operate your vehicle is
impaired by alcohol, drugs, or some other
physical condition.
DRIVING SAFETY PRECAUTIONS
Your INFINITI is designed for both normal
and off-road use. However, avoid driving in
deep water or mud as your INFINITI is mainly
designed for leisure use, unlike a conventional
off-road vehicle.
Remember that 2–wheel drive vehicles are
less capable than all-wheel drive (AWD)
models for rough road driving and extrication
when stuck in deep snow or mud, or the like.Please observe the following precautions:
WARNING
•Spinning the front wheels on slippery
surfaces may cause the AWD warning
message to display and the AWD system
to automatically switch from the AWD
to 2WD mode. This could reduce the
traction. Be especially careful when
towing a trailer. (AWD models)
•Drive carefully when off the road and
avoid dangerous areas. Every person
who drives or rides in this vehicle should
be seated with their seat belt fastened.
This will keep you and your passengers
in position when driving over rough ter-
rain.
•Do not drive across steep slopes. Instead
drive either straight up or straight down
the slopes. Off-road vehicles can tip
over sideways much more easily than
they can forward or backward.
•Many hills are too steep for any vehicle.
If you drive up them, you may stall. If you
drive down them, you may not be able to
control your speed. If you drive across
them, you may roll over.
5-10Starting and driving

You do not have to remove the start/stop
button from the ignition lock when you leave
the vehicle. You should, however, always
take the key with you when leaving the ve-
hicle. As long as the key is in the vehicle:
•The vehicle can be started using the push-
button ignition switch.
•The electrically powered equipment can be
operated.
EMERGENCY ENGINE SHUT OFF
To shut off the engine in an emergency situ-
ation while driving, perform the following
procedure:
•Rapidly push the push-button ignition
switch 3 consecutive times in less than
1.5 seconds, or
•Push and hold the push-button ignition
switch for more than 2 seconds.
•Make sure the area around the vehicle is
clear.
•Check fluid levels such as engine oil, cool-
ant, brake fluid, and windshield-washer
fluid as frequently as possible, or at least
whenever you refuel.
•Check that all windows and lights are
clean.
•Visually inspect tires for their appearance
and condition. Measure and check the tire
pressure for proper inflation.
•Check that all doors are closed.
•Position seat and adjust head restraints/
headrests.
•Adjust the inside and outside rear view
mirrors.
•Fasten your seat belt and ask all passen-
gers to do likewise.
•Check the operation of the warning lights
when the ignition switch is pushed to the
ON position.
STARTING PROCEDURE WITH
THE KEY
0OFF position
1ACC position
2ON position
3START position
1. Apply the parking brake.
2. Shift the transmission to position P (Park)
by pressing the

button.
The transmission position indicator in the
vehicle information display shows

When the transmission is in position N
(Neutral), you can also start the engine
with the brake pedal depressed.
The starter is designed not to operate if the
shift lever is in any of the driving positions.
NPA1483
BEFORE STARTING ENGINE STARTING ENGINE
5-16Starting and driving

Shifting
P Park position with parking lock
R Reverse
N Neutral
D DriveTransmission position display:
NOTE
If the transmission position display in the ve-
hicle information display is not working, you
should pull away carefully to check whether
the desired transmission position IS en-
gaged. Ideally, you should select transmis-
sion position D and automatic drive program
EorS.
The shift lever indicator
1located in the
lower part of the vehicle information display
shows the current position of the transmis-
sion.
It shows the P,R,N,D modes when the trans-
mission is in auto mode or the shift position
when the transmission is in manual mode.
WARNING
Apply the parking brake if the shift lever is
in any position while the engine is not run-
ning. Failure to do so could cause the ve-
hicle to move unexpectedly or roll away
and result in serious personal injury or
property damage.
CAUTION
Use the P (Park) or R (Reverse) position only
when the vehicle is completely stopped.NSD585NSD649
Starting and driving5-19

Holding the vehicle stationary on
uphill gradients
WARNING
If the transmission overheats, the elec-
tronic management system is automati-
cally deactivated. This interrupts the
power transmission from the engine to the
wheels. The vehicle may, for example, roll
backwards on gradients. There is a risk of
an accident. Never hold the vehicle station-
ary on uphill gradients by depressing the
accelerator.
The transmission may overheat if you hold
the vehicle stationary on uphill gradients by
depressing the accelerator pedal. If the trans-
mission overheats, a warning tone sounds
and the [Stop Vehicle Shift to P Leave Engine
Running] display message appears in the ve-
hicle information display. You will only be able
to continue your journey once the transmis-
sion has cooled down and the display mes-
sage in the vehicle information display has
disappeared.Never hold the vehicle stationary on uphill
gradients by depressing the accelerator. In-
stead, only ever hold the vehicle stationary on
uphill gradients by:•Depressing the brake pedal.
•Engaging the electric parking brake.
Kickdown
Use kickdown for maximum acceleration:
•Depress the accelerator pedal beyond the
pressure point.
The transmission shifts to a lower gear
depending on the engine speed.
•Ease off the accelerator pedal once the
desired speed is reached.
The automatic transmission shifts back up.
Starting and driving5-21

Drive mode switch
The drive mode switch allows you to choose
between drive programs with different driv-
ing characteristics.
Press drive mode switch
1. A popup2will
be displayed in the vehicle information dis-
play showing the current selection. After
around 2 seconds, the selected drive program
appears in the lower frame of the vehicle
information display
3and the popup will
disappear.The automatic transmission switches to drive
program E each time the engine is started.
E (Economy): comfortable, economical driv-
ing
S (Sport): sporty driving style
M (Manual): manual gear shifting
For more details of the manual drive program
see "Manual drive program" later in this sec-
tion.
NSD587NSD726
NSD725
5-22Starting and driving

Steering wheel gearshift paddles
1Left steering wheel gearshift paddle
(shifts down)
2Right steering wheel gearshift paddle
(shifts up)
In drive program M, you can change gear
yourself using the steering wheel gearshift
paddles.
If you pull the left or right steering wheel
gearshift paddle when in automatic drive
program E or S, the automatic transmission
shifts into drive program M for a limited time.
Depending on which gearshift paddle is
pulled, the automatic transmission immedi-
ately shifts into the next gear down or up.
Automatic drive programs
Drive program E is characterized by the fol-
lowing:
•Comfort-oriented engine settings.
•Optimal fuel consumption resulting from
the automatic transmission shifting up
sooner.
•The vehicle pulling away more gently in
forward and reverse gears unless the ac-
celerator pedal is depressed fully.
•Increased sensitivity. This improves handling
on slippery road surfaces, for example.
•The automatic transmission shifting up
sooner. This results in the vehicle being
driven at lower engine speeds and the
wheels being less likely to spin.
Drive program S is characterized by the fol-
lowing:
•Sporty engine settings.
•The automatic transmission shifting up later.
•As a result of the later automatic transmis-
sion shift points, the fuel consumption
possibly being higher.
Manual drive program
In manual drive program M, you can change
gear yourself by using the steering wheel
gearshift paddles. For this, the transmission
must be in position D (Drive). The gear cur-
rently selected and engaged is shown in the
vehicle information display
Manual drive program M differs from drive
programs E and S with regard to spontaneity,
responsiveness and smoothness of gear
changes.
Using manual gears:
3 To use the engine's braking effect
2 To use the braking effect of the engine on
downhill gradients and for driving on steep
mountain roads, in mountainous terrain or
in arduous conditions.
1 To use the braking effect of the engine on
extremely steep downhill gradients and on
long downhill stretches.
NSD584
Starting and driving5-23

Activating the manual drive program:
•Permanently: Press the drive mode switch
1repeatedly until M appears in the ve-
hicle information display. Manual drive
program M remains active until drive pro-
gram E or S is engaged.
•Temporarily: Pull the right or left steering
wheel gearshift paddle (see "Steering
wheel gearshift paddles" later in this sec-
tion). Manual drive program M is tempo-
rarily active. Depending on which gearshift
paddle is pulled, the automatic transmis-
sion immediately shifts into the next gear
down or up.
When manual drive program M is activated
via the steering wheel gearshift paddles, the
temporarily active manual drive program M
will be deactivated automatically after a lim-ited time, if the driving situation permits. The
automatic transmission switches to the pre-
viously activated drive program E or S. When
driving on downhill gradients, the temporarily
active manual drive program M will only be
deactivated if the accelerator pedal is de-
pressed while the vehicle is rolling downhill.
Upshifting:
Pull the right-hand steering wheel gearshift
paddle (see "Steering wheel gearshift
paddles" earlier in this section). The auto-
matic transmission shifts up to the next gear.
In order to prevent engine damage the auto-
matic transmission automatically shifts up if
the maximum engine speed on the currently
engaged gear is reached and you depress the
accelerator pedal.Gearshift recommendation:
The gearshift recommendations assist you in
adopting an economical driving style. The
recommended gear is shown in the vehicle
information display.
Shift to recommended gear1according to
gearshift recommendation
2when shown in
the vehicle information display.
Downshifiting:
Pull the left-hand steering wheel gearshift
paddle (see "Steering wheel gearshift
paddles" earlier in this section). The auto-
matic transmission shifts down to the next
gear.
If you slow down or stop without shifting
down, the automatic transmission automati-
cally shifts down.
NSD587NSD589
5-24Starting and driving

The Idle Stop/Start function switches the
engine off automatically if the vehicle is
stopped under certain conditions.
When pulling away again, the engine starts
automatically. The Idle Stop/Start function
thereby helps you to reduce the fuel con-
sumption and emissions of your vehicle.
WARNING
If the engine is switched off automatically
and you exit the vehicle, the engine is re-
started automatically. The vehicle may be-
gin moving There is a risk of accident and
injury.
If you wish to exit the vehicle, always turn
off the ignition and secure the vehicle
against rolling away.If the
Idle Stop/Start symbol is shown
in green in the vehicle information display,
the Idle Stop/Start function switches the
engine off automatically once the vehicle
stops moving.
The Idle Stop/Start function is automatically
activated each time you start the engine with
the ignition switch.
If the Idle Stop/Start function has been manu-
ally deactivated (see"Deactivating/activating
the Idle Stop/Start function" later in this sec-
tion) or a malfunction has caused the system
to be deactivated, the
Idle Stop/Start
symbol is not displayed.
AUTOMATIC ENGINE
SWITCH-OFF
The Idle Stop/Start function is operational
and theIdle Stop/Start symbol is dis-
played in green in the vehicle information dis-
play, if:
•The indicator light in the Idle Stop/Start
button is lit green.
•The outside temperature is within the
range that is suitable for the system.
•The engine is at normal operating tem-
perature.
•The set temperature for the vehicle interior
has been reached.
•The battery is sufficiently charged.
•The system detects that the windshield is
not misted up when the air-conditioning
system is switched on.
•The hood is closed.
•The driver's door is closed and the driver's
seat belt is fastened.
If the conditions for automatic engine
switch-off are not all fulfilled, the
Idle
Stop/Start symbol is shown in yellow.
NSD620
Idle Stop/Start symbol
IDLE STOP/START SYSTEM (IF
EQUIPPED)
Starting and driving5-29