15 of 5 INFINITI QX30 2019 Owner's Manual

7. Make sure that wiper blade1is seated
correctly.
8. Move the wiper arm back onto the rear
window.If the brakes do not operate properly, it is
recommended that you have the brakes
checked. It is recommended that you visit an
INFINITI retailer for this service.
SELF-ADJUSTING BRAKES
Your vehicle is equipped with self-adjusting
brakes. The disc-type brakes self-adjust ev-
ery time the brake pedal is applied.Blown fuses must be replaced with fuses of
the same rating, which you can recognize by
the color and fuse rating. The fuse ratings are
listed in the fuse allocation chart.
If the newly inserted fuse also blows, have
the cause traced and rectified. It is recom-
mended you visit an INFINITI retailer for this
service.
The fuses in your vehicle disconnect faulty
circuits. if a fuse blows, all the components on
the circuit and their functions will fail.
BEFORE REPLACING A FUSE
•Secure the vehicle against rolling away.
•Switch off all electrical consumers.
•Remove the key from the ignition lock.
The fuses are located in various fuse boxes:
•Fuse box in the engine compartment on
the left-hand side of the vehicle, when
viewed in the direction of travel.
•Fuse box in the front-passenger footwell.
The fuse allocation chart is on the fuse box in
the front-passenger footwell.
BRAKES FUSES
Do-it-yourself8-17

ENGINE COMPARTMENT
WARNING
Never use a fuse of higher or lower amper-
age rating than that specified on the fuse
box cover. This could damage the electrical
system or electronic control units or cause
a fire.
1. Open the hood
2. Remove any existing moisture from the
fuse box using a dry cloth
3. To open: open clamps
2.
4. Fold cover
1up in the direction of the
arrow and remove it.To close:
1. Check whether the seal is lying correctly in
cover
1.
2. Insert cover
1at the back into openings
3on the fuse box.
NDI1591NDI1592
8-18Do-it-yourself

3. Fold down cover1.
4. Hook clamps into the fuse box and close
5. Close the hood.
PASSENGER COMPARTMENT
WARNING
Never use a fuse of higher or lower amper-
age rating than that specified on the fuse
box cover. This could damage the electrical
system or electronic control units or cause
a fire.To open:
1. Open the front-passenger door.
2. Remove the floor mats.
3. Fold out perforated floor covering
1in
the direction of the arrow.
NDI1593
Do-it-yourself8-19

4. To release cover3press retaining clamp
2.
5. Fold out cover
3in the direction of the
arrow to the catch.
6. Remove cover
3forwards.
NOTE
Fuse allocation chart
4is located on the
lower right-hand side of cover
3.To close:
1. Insert cover
3on the left-hand side of
the fuse box into the retainer. Cover
3engages in the retainers.
2. Fold down cover
3until clamps2lock
audibly.
3. Fold back perforated floor covering
1.
4. Fit the floor mats.
CAUTION
Be careful not to allow children to swallow
the battery or removed parts.
NDI1594
INTELLIGENT KEY BATTERY
REPLACEMENT
8-20Do-it-yourself

CHECKING THE BATTERY
Press the(LOCK) or(UNLOCK)
button.
The battery is working properly if the battery
check light
1lights up briefly.
The battery is discharged if the battery check
light
1does not light up briefly. Replace the
battery.
NOTE
•If the key battery is checked within the
signal reception range of the vehicle,
pressing the
(LOCK) or(UN-
LOCK) button locks or unlocks the ve-
hicle.
•You can obtain a battery from an INFINITI
retailer.
REPLACING THE BATTERY
You require a CR 2025 3 V cell battery.
Replace the battery in the Intelligent Key as
follows:
1. Take the emergency key element out of
the key (see "Mechanical key")
2. Press emergency key element
2into the
opening into the key in the direction of the
arrow until the battery cover
1opens.
When doing so, do not hold cover
1shut.
3. Remove battery tray cover
1.4. Repeatedly tap the key against your palm
until battery
1falls out.
NPA1474NPA1472NPA1473
Do-it-yourself8-21

5. Insert the new battery with the positive
terminal facing upwards. Use a lint-free
cloth to do so.
6. Make sure that the surface of the battery
is free of lint, grease and other contami-
nation.
7. Insert the front tabs of battery cover
1and then press to close it.
8. Insert emergency key element into the key
(see "Mechanical key").
9. Check the function of all key buttons on
the vehicle.
If you need assistance with replacement, it is
recommended that you visit an INFINITI re-
tailer for this service.FCC Notice:
For USA:
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) This device may not
cause harmful interference, and (2) this de-
vice must accept any interference received,
including interference that may cause unde-
sired operation.
NOTE
Changes or modifications not expressly ap-
proved by the party responsible for compli-
ance could void the user’s authority to oper-
ate the equipment.
For Canada:
This device complies with Industry Canada
license-exempt RSS standard(s). Operation
is subject to the following two conditions: (1)
this device may not cause interference, and
(2) this device must accept any interference,
including interference that may cause unde-
sired operation of the device.
SPA0784Z
8-22Do-it-yourself

EXTERIOR AND INTERIOR LIGHTS
Item Wattage (W)
Front combination light
Headlight (Low or high beam: H9 type) 14 / 28
Headlight (Low or high beam: LED type, if so equipped) *1 LED
Front turn signal light (with halogen headlights) 24
Front turn signal light (LED type, if so equipped)*1 LED
Front side light *1 LED
Daytime driving light *1 LED
Front fog light *1 LED
Side turn signal light *1 LED
Puddle light *1 LED
Rear combination light
Turn signal light*1 LED
Stop/Tail light *1 LED
Reversing light *1 LED
Brake light *1 LED
High-mounted brake light *1 LED
License plate light*1 LED
Room light/Map lights (if so equipped)
Foot well light (if so equipped)5
3
Reading light (rear)
Room light — rear (if so equipped)5
5
Reading lights — rear (if so equipped) 8
Luggage compartment light 5
*1: It is recommended you visit an INFINITI retailer for replacement.It is recommended you check with the Parts
Department at an INFINITI retailer for the
latest parts information.
LIGHTS
Do-it-yourself8-23

1Side turn signal light
2Room light / Map lights (if so equipped)
3Daytime driving light and sidelights and
turn signal (if so equipped)
4Low/High beam headlight
5High beam headlight or turn signal
6Cornering light (if so equipped)
7Front fog light (if so equipped)
8Daytime driving light and sidelights
9Footwell light (if so equipped)
10Room light (if so equipped)
11High mounted stop light
12License plate light
13Rear Fog and Reversing light
14Brake light
15Turn signal light
16Tail light
Front light unit
Halogen type:
1Turn signal light
2Daytime driving light and sidelight
3High/Low beam halogen projector head-
lights
4Side marker light (if so equipped)
5Reflector (if so equipped)
6Daytime driving light and sidelights
NDI1625
NDI1613
8-24Do-it-yourself

LED type:
1Cornering light
2Additional high-beam headlight
3Daytime driving light and sidelight and
turn signal light
4High/Low beam LED projector head-
lights and Adaptive Front Lighting sys-
tem (if so equipped)
5Side marker light (if so equipped)
6Reflector (if so equipped)
7Daytime driving light and sidelights
Rear light unit
1Tail light
2Turn signal light
3Brake light
4Tail light
5Reversing light
6Rear fog light (drivers side only)
REPLACEMENT PROCEDURES
LED lights (if so equipped)
The LED headlight is a projector style which
uses a LED module without serviceable parts.
If LED fog headlight , or any other LED light
replacement is required, it is recommended
that you visit an INFINITI retailer for this
service.
Halogen headlight bulb
Fitting/removing the access cover on the
front wheel arch:
You must remove the cover of the front
wheel arch before you can change the halo-
gen headlight bulb.
To remove: switch off the lights, turn the
steering so that the wheel behind the light in
question is pointing inwards . Slide cover
1up and remove it.
To fit: inset cover
1again and slide it down
until it engages.
NDI1614NDI1615NDI1626
Do-it-yourself8-25

The headlight is a semi-sealed beam type
which uses a replaceable headlight (halogen)
bulb. A bulb can be replaced from inside the
engine compartment without removing the
headlight assembly.
If you need assistance for bulb replacement,
it is recommended that you visit an INFINITI
retailer.
Low/High beam Headlight bulb replace-
ment:
1. Open the hood. For details, see "Hood".
2. Disconnect the negative (—) battery cable.
3. Remove the corresponding access cover
from the wheel arch.
4. Turn housing cover
1counterclockwise
and remove it.
5. Turn bulb holder
2counterclockwise and
pull out
6. Take the headlight bulb out of bulb holder
2.
7. Insert the new bulb into bulb holder
2.
8. Insert bulb holder
2and turn it clockwise.9. Press on housing cover
1and turn it to
the right.
10. Replace the cover in the front wheel arch
11. Reconnect the negative (—) battery cable
and close the hood.
NOTE
Fog may temporarily form inside the lens of
the exterior lights in the rain or in a car wash.
The fog is caused by a temperature differ-
ence between the inside and the outside of
the lens. This is not a malfunction. If large
droplets can be seen, it is recommended that
you visit an INFINITI retailer.
NDI1611
8-26Do-it-yourself