change time INFINITI QX30 2019 Owner's Manual
[x] Cancel search | Manufacturer: INFINITI, Model Year: 2019, Model line: QX30, Model: INFINITI QX30 2019Pages: 436, PDF Size: 4.31 MB
Page 4 of 436
For additional information, refer to “On-
pavement and off-road driving precau-
tions”, “Avoiding collision and rollover” and
“Driving safety precautions” in the “Starting
and driving” section of this manual.
MODIFICATION OF YOUR
VEHICLE
This vehicle should not be modified. Modifi-
cation could affect its performance, safety
or durability and may even violate govern-
mental regulations. In addition, damage or
performance problems resulting from modi-
fications may not be covered under INFINITI
warranties.
WARNING
Installing an aftermarket On-Board Diag-
nostic (OBD) plug-in device that uses
the port during normal driving, for example
remote insurance company monitoring,
remote vehicle diagnostics, telematics or
engine reprogramming, may cause inter-
ference or damage to vehicle systems. We
do not recommend or endorse the use of
any aftermarket OBD plug-in devices, un-
less specifically approved by INFINITI. The
vehicle warranty may not cover damage
caused by any aftermarket plug-in device.
WHEN READING THE MANUAL
This manual includes information for all fea-
tures and equipment available on this model.
Features and equipment in your vehicle may
vary depending on model, trim level, options
selected, order, date of production, region or
availability. Therefore, you may find informa-
tion about features or equipment that are not
included or installed on your vehicle.
All information, specifications and illustra-
tions in this manual are those in effect at the
time of printing. INFINITI reserves the right
to change performance, design or compo-
nent suppliers without notice and without
obligation.
From time to time, INFINITI may update or
revise this manual to provide Owners with
the most accurate information currently
available. Please carefully read and retain
with this manual all revision updates sent to
you by INFINITI to ensure you have access
to accurate and up-to-date information
regarding your vehicle. Current versions
of vehicle Owner’s Manuals and any up-
dates can also be found in the Owner sec-
tion of the INFINITI website at https://
owners.infinitiusa.com/owners/navigation/
manualsandGuides. If you have questions
concerning any information in your Owner’s
Manual, contact INFINITI Consumer Affairs.See the INFINITI CUSTOMER CARE PRO-
GRAM page in this Owner’s Manual for con-
tact information.
IMPORTANT INFORMATION
ABOUT THIS MANUAL
You will see various symbols in this manual.
They are used in the following ways:
WARNING
This is used to indicate the presence of a
hazard that could cause death or serious
personal injury. To avoid or reduce the risk,
the procedures must be followed precisely.
CAUTION
This is used to indicate the presence of a
hazard that could cause minor or moderate
personal injury or damage to your vehicle.
To avoid or reduce the risk, the procedures
must be followed carefully.
NOTE
Indicates additional helpful information.
Page 69 of 436
•Right after inflation, several side air bag
and curtain air bag system components
will be hot. Do not touch them; you may
severely burn yourself.
•No unauthorized changes should be
made to any components or wiring of
the side air bag and curtain air bag sys-
tems. This is to prevent damage to or
accidental inflation of the side air bag
and curtain air bag systems.
•Do not make unauthorized changes to
your vehicle’s electrical system, suspen-
sion system or side panel. This could af-
fect proper operation of the curtain air
bag systems.
•Tampering with the side air bag system
may result in serious personal injury. For
example, do not change the front seats
by placing material near the seatbacks
or by installing additional trim material,
such as seat covers, around the side air
bag.
•It is recommended that you visit an
INFINITI retailer for work on and around
the front air bag. It is also recommended
that you visit an INFINITI retailer for
installation of electrical equipment. The
SRS wiring harnesses* should not be
modified or disconnected. Unauthorizedelectrical test equipment and probing
devices should not be used on the side air
bag or curtain air bag systems.
Driver and passenger supplemental
knee air bags
The driver's knee air bag deploys under the
steering column, while the passenger's knee
air bag deploys under the glove box. All of the
information, cautions and warnings in this
manual apply and must be followed. The driv-
er's and passenger's knee air bags are trig-
gered together with the front air bag. The
knee air bags are designed to inflate in higher
severity frontal collisions, although they may
inflate if the forces in another type of collision
are similar to those of a higher severity fron-
tal impact. They may not inflate in certain
collisions.
Vehicle damage (or lack of it) is not always an
indication of proper knee air bag operation.
When a knee air bag inflates, a fairly loud
noise may be heard, followed by release of
smoke. This smoke is not harmful and does
not indicate a fire. Care should be taken not
to inhale it, as it may cause irritation and
choking. Those with a history of a breathing
condition should get fresh air promptlyThe knee air bags help to cushion the impact
force on the knees of the driver and front
passenger. They can help reduce serious inju-
ries. However, an inflating knee air bag may
cause abrasions or other injuries. The knee air
bag provides restraint to the lower body.
The knee air bag inflates quickly in order to
help protect the occupants. Because of this,
the force of the knee air bag inflating can
increase the risk of injury if the occupant is
too close to, or is against, this air bag module
during inflation. The knee air bag will deflate
quickly after the collision is over OR the knee
air bag will remain inflated for a short time.
The knee air bags operate only when the ig-
nition switch is placed in the ON position.
After placing the ignition switch in the ON
position, the supplemental air bag warning
light illuminates. The supplemental air bag
warning light will turn off a few seconds af-
ter the engine starts if the system is opera-
tional.
WARNING
•Do not place any objects between the
knee bolster and the driver’s seat. Such
objects may become dangerous projec-
tiles and cause injury if a knee air bag
inflates.
Safety — seats, seat belts and supplemental restraint system1-51
Page 100 of 436
When you switch the [Adaptive front lighting
system] function on, you activate the follow-
ing functions:
•Freeway mode
•Active light function
•Cornering light function
If you set the low beam headlights for driving
on the right/left, the vehicle information dis-
play shows the [Adaptive front lighting
system: System Inoperative Inactive For
Left-side Traffic] or [Adaptive front lighting
system: System Inoperative Inactive for
Right-side Traffic] display message instead
of the [Adaptive front lighting] function in the
[Light] submenu.
For further information about the Adaptive
Front Lighting system, see " Adaptive front
lighting system (LED headlight only) (if
equipped)" later in this section
Setting the low beam headlights for driving
on the left/right:
This function is only available on vehicles with
the Adaptive Front Lighting System (see "
Adaptive front lighting system (LED head-
light only) (if equipped)" later in this section).1. Press the
orbutton on the
steering wheel to select the [Settings]
menu.
2. Press the
orbutton to select
[Light] submenu.
3. Press
4. Press the
orbutton to select
the [Low-b. Headl. Setting For:] function.
You will see the selected setting: [Right-
side Traffic] or [Left-side Traffic].
5. Press the
If you change the setting, conversion does
not take place until the next time the ve-
hicle is stationary.
If you set the low beam headlights for driving
on the right/left, then freeway mode is un-
available. This is only deactivated if the set-
ting for driving on the left/right is set oppo-
site to your vehicle's country version.
An INFINITI retailer can set the low beam
headlights for driving on the left/right.
Setting the brightness of the ambient light-
ing:
1. Press the
orbutton on the
steering wheel to select the [Settings]
menu.2. Press the
orbutton to select
[Light] submenu.
3. Press
4. Press the
orbutton to select
the [Ambient Light Brightness] function.
You will see the selected setting.
5. Change the setting with
If you change the setting, conversion does
not take place until the next time the ve-
hicle is stationary.
6. Press the
orbutton to adjust
the brightness to a level from [Off] to
[Level 5] (bright).
7. Press the
button to save the
setting.
Activating/deactivating the surround
lighting and exterior lighting delayed
switch-off:
If you have activated the Surround lighting
function and the light switch is set to
vated when it is dark:
•Surround lighting: the exterior lighting re-
mains lit for 40 seconds after unlocking
with the key. If you start the engine, the
surround lighting is switched off and auto-
matic headlight mode is activated .
2-26Instruments and controls
Page 141 of 436
COMBINATION SWITCH
1Turn signal, right
2Turn signal, left
3High beam headlights
4Headlight flasher
Turn signal
Move the lever up or down to signal the
turning direction. When the turn is com-
pleted, the turn signal cancels automatically.
Lane change signal
Move the lever up or down until the turn
signal begins to flash, but the lever does not
latch, to signal a lane change. Hold the lever
until the lane change is completed. Move the
lever up or down until the turn signal begins
to flash, but the lever does not latch, and
release the lever. The turn signal will auto-matically flash three times. Choose the ap-
propriate method to signal a lane change
based on road and traffic conditions.
High beam headlights
To switch on the high beam headlights:
•Turn the ignition switch to the ON position
or start the engine.
•Turn the light switch toor
•Press the combination switch beyond the
pressure point in the direction of arrow
3.
In the
headlights are only switched on when it is
dark and the engine is running.
The blue
indicator light in the com-
bination meter lights up when the high
beam headlights are switched on.
To switch off the high beam headlights:
•Move the combination switch back to its
normal position. The blueindicator
light in the combination meter goes out.
NOTE
Vehicles with High beam Assist: when High
beam Assist is active, it controls activation
and deactivation of the high beam head-
lights (see " High beam assist (LED headlight
only)" later in this section)
ADAPTIVE FRONT LIGHTING
SYSTEM (LED HEADLIGHT
ONLY) (IF EQUIPPED)
The Adaptive Front Lighting System is a sys-
tem that adjusts the headlights automatically
to suit the prevailing driving and weather
conditions. It offers advanced functions for
improved illumination of the road surface,
e.g. depending on the vehicle speed or
weather conditions. The system includes the
active light function, cornering light function
and freeway mode. The system is only active
when it is dark.
You can activate or deactivate the “Adaptive
Front Lighting System” function using the
vehicle information display (see "Switching
the Adaptive Front Lighting System on/off"
earlier in this section)
NIC2618
Instruments and controls2-67
Page 143 of 436
HIGH BEAM ASSIST (LED
HEADLIGHT ONLY)
You can use this function to set the head-
lights to change between low beam and high
beam automatically. The system recognizes
vehicles with their lights on, either approach-
ing from the opposite direction or traveling in
front of your vehicle, and consequently
switches the headlights from high beam to
low beam.
The system automatically adapts the low
beam headlight range depending on the dis-
tance to the other vehicle. Once the system
no longer detects any other vehicles, it
switches on the high beam headlights again.
The system's optical sensor is located behind
the windshield near the overhead control
panel.
WARNING
•The high beam assist system is a conve-
nience but is not a substitute for safe
driving operation. The driver should re-
main alert at all times, ensure safe driv-
ing practices and switch the high beams
and low beam manually when necessary.
•The high beam or low beam may not
switch automatically under the follow-
ing conditions. Switch the high beam
and low beam manually.
–During bad weather (rain, fog, snow,
wind, etc.).
–When a light source similar to a head-
light or tail light is in the vicinity of
the vehicle.
–When the headlights of the oncoming
vehicle or the leading vehicle are
turned off, when the color of the light
is affected due to foreign materials
on the lights, or when the light beam
is out of position.
–When there is a sudden, continuous
change in brightness.
–When driving on a road that passes
over rolling hills, or a road that has
level differences.
–When driving on a road with many
curves.–When a sign or mirror-like surface is
reflecting intense light towards the
front of the vehicle.
–When the container, etc. being towed
by a leading vehicle is reflecting in-
tense light.
–When a headlight on your vehicle is
damaged or dirty.
–When the vehicle is leaning at an
angle due to a punctured tire, being
towed, etc.
•The timing of switching the low beam
and high beam may change under the
following situations.
–The brightness of the headlights of
the oncoming vehicle or leading ve-
hicle.
–The movement and direction of the
oncoming vehicle and the leading ve-
hicle.
–When only one light on the oncoming
vehicle or the leading vehicle is illumi-
nated.
–When the oncoming vehicle or the
leading vehicle is a two-wheeled ve-
hicle.
–Road conditions (incline, curve, the
road surface, etc.).
–The number of passengers and the
amount of luggage.
NDS595
Instruments and controls2-69
Page 179 of 436
4. All doors and the lift gate will lock.
5. The turn signals flash three times.
NOTE
•Doors do not lock by pushing the door
handle request switch while any door is
open. However, doors lock with the me-
chanical key even if any door is open.
•The driver's door and the door at which
the handle is used, must both be closed.
•The doors may not lock when the Intelli-
gent Key is in the same hand that is oper-
ating the request switch to lock the door.
Put the Intelligent Key in a purse, pocket
or your other hand.
CAUTION
•When locking the doors using the re-
quest switch, make sure to have the In-
telligent Key in your possession before
operating the request switch to prevent
the Intelligent Key from being left in the
vehicle.
•The request switch is operational only
when the Intelligent Key has been de-
tected by the Intelligent Key system.
Unlocking doors
1. Carry the Intelligent Key.
2. Touch the inner surface of the door
handle.
3. All doors and the lift gate will unlock.
4. The turn signals flash once.
Deactivating and activating
If you do not intend to use the vehicle for an
extended period of time, you can deactivate
the Intelligent Key. The key will then use very
little power, thereby conserving battery
power. For the purposes of activation/
deactivation, the vehicle does not have to be
nearby.
To deactivate:press the
button on the
key twice in rapid succession The battery
check lamp of the key lights up twice briefly
and Intelligent Key is deactivated.
To activate:press any button on the key or
insert the key into the ignition lock. The Intel-
ligent Key and all of its associated features
are available again.
CHANGING THE SETTINGS OF
THE LOCKING SYSTEM
You can change the settings of the locking
system. This means that only the driver's door
and the fuel-filler lid are unlocked when the
vehicle is unlocked. This is useful if you fre-
quently travel alone.To change the setting:simultaneously
press theandbuttons for approxi-
mately 6 seconds.
NOTE
If the setting of the locking system is
changed within the signal range of the ve-
hicle, pressing the
andbutton will
lock or unlock the vehicle.
The key now functions as follows:
To unlock the driver's door:press the
button once.
To unlock centrally:press the
button
twice.
To lock centrally:press the
button.
The Intelligent Key function is changed as
follows:
To unlock the driver's door:touch the inner
surface of the door handle on the driver's
door.
To unlock centrally:touch the inner surface
of the door handle on the front passenger
door or the rear door.
To lock centrally:touch the outer sensor sur-
face on one of the door handles
To restore the factory settings:
simultane-
ouslypress theandbutton for ap-
proximately 6 seconds.
Pre-driving checks and adjustments3-11
Page 221 of 436
•Recommendation for air distribution in
winter: select theandsettings.
Recommendation for air distribution in
summer: select the
orandsettings.
•Only use the "Windshield demisting" func-
tion briefly until the windshield is clear again
•Only use air-recirculation mode briefly, for
example if there are unpleasant outside
odors or when in a tunnel. The windows
could otherwise mist up as no fresh air is
drawn into the vehicle in air-recirculation
mode
•If you change the settings of the climate
control system, the climate status display
appears for approximately three seconds
at the bottom of the screen in the central
display (see separate operating instruc-
tions). You will see the current settings of
the various climate control functions.
Switching air-conditioning system
on/off
Make sure the ignition switch is in the ON
position.
To switch on:turn control
5clockwise to the
desired position (except position0).
To switch off:turn control
5counter-
clockwise to position0.
Activating/deactivating the cooling
with air dehumidification function
If you deactivate the "Cooling with air dehu-
midification" function, the air inside the ve-
hicle will not be cooled. The air inside the
vehicle will also not be dehumidified. The
windows can mist up more quickly. There-
fore, only deactivate the "Cooling with air
dehumidification" function briefly.
The "Cooling with air dehumidification" func-
tion is only available when the engine is run-
ning. The air inside the vehicle is cooled and
dehumidified according to the temperature
selected.
Condensation may drip from the underside of
the vehicle when cooling mode is active. This
is normal and not a sign that there is a mal-
function.
To activate:
Press the
button The indicator light in
thebutton lights up.
To deactivate:
Press the
button. The indicator light in
thebutton goes out. The cooling with
air dehumidification function has a delayed
switch-off feature.Problems with the "Cooling with air dehu-
midification" function:
Problem:The indicator light in the
but-
ton flashes three times or remains off. The
cooling with air dehumidification function
cannot be activated.
Cause and solution:The cooling with air de-
humidification function has been deactivated
due to a malfunction. Have the system
checked. It is recommended you visit an
INFINITI retailer for this service.
Setting the temperature
You can set the temperature for the entire
vehicle. The set temperature is automatically
maintained at a constant level.
To increase or reduce the temperature: turn
control
1counterclockwise or clockwise.
Only change the temperature setting in small
increments. Start at 70° F (22° C).
Setting the air distribution
Directs the airflow through the demis-
ter ventilators.
Directs the airflow through the center
and side air ventilators.
Directs the airflow through the foot-
well air ventilators.
Display screen, heater and air conditioner, and audio system4-31
Page 225 of 436
•If you change the settings of the climate
control system, the climate status display
appears for approximately three seconds
at the bottom of the screen in the center
display (see separate operating instruc-
tions). You will see the current settings of
the various climate control functions.
Idle Stop/Start function
During automatic engine switch-off, the Cli-
mate control only operates at a reduced ca-
pacity. If you require the full climate control
output, you can switch off the Idle Stop/
Start function by pressing the Idle Stop/Start
button (see " Idle Stop/Start System (if
equipped)").
Switching automatic climate
control on/off
When the climate control is switched off, the
air supply and air circulation are also
switched off. The windows could mist up.
Therefore, only switch off climate control
briefly.
Make sure the ignition switch is in the ON
position.
To activate:
Press the
button The indicator light in
thebutton lights up. Airflow and air
distribution are set to automatic mode.or
Press thebutton. The indicator light in
thebutton goes out. The previous settings
are reactivated.
To deactivate:
Press the
button. The indicator light in
thebutton lights up.
NOTE
Automatic climate control: switch on climate
control primarily using the
button.
Activating/deactivating the cooling
with air dehumidification function
If you deactivate the "Cooling with air dehu-
midification" function, the air inside the ve-
hicle will not be cooled. The air inside the
vehicle will also not be dehumidified. The
windows can mist up more quickly. There-
fore, only deactivate the "Cooling with air
dehumidification" function briefly.
The "Cooling with air dehumidification" func-
tion is only available when the engine is run-
ning. The air inside the vehicle is cooled and
dehumidified according to the temperature
selected.
Condensation may drip from the underside of
the vehicle when cooling mode is active. This
is normal and not a sign that there is a mal-
function.To activate:
Press the
button The indicator light in
thebutton lights up.
To deactivate:
Press the
button. The indicator light in
thebutton goes out. The cooling with
air dehumidification function has a delayed
switch-off feature.
Problems with the "Cooling with air dehu-
midification" function:
Problem:The indicator light in the
but-
ton flashes three times or remains off. The
cooling with air dehumidification function
cannot be activated.
Cause and solution:The cooling with air de-
humidification function has been deactivated
due to a malfunction. Have the system
checked. It is recommended you visit an
INFINITI retailer for this service.
Setting automatic climate control
to automatic mode
Only automatic climate control features the
"Control climate control automatically" func-
tion.
In automatic mode, the set temperature is
maintained automatically at a constant level
Display screen, heater and air conditioner, and audio system4-35
Page 234 of 436
WARNING
•Never leave children or adults who
would normally require the support of
others alone in your vehicle. Pets should
not be left alone either. They could un-
knowingly activate switches or controls
and inadvertently become involved in a
serious accident and injure themselves.
On hot, sunny days, temperatures in a
closed vehicle could quickly become high
enough to cause severe or possibly fatal
illness to people or animals.
•Properly secure all cargo to help prevent
it from sliding or shifting. Do not place
cargo higher than the seatbacks. In a
sudden stop or collision, unsecured
cargo could cause personal injury.
•To avoid raising the center of gravity
excessively, do not exceed the rated ca-
pacity of the roof rack (if so equipped)
and evenly distribute the load.
EXHAUST GAS (CARBON
MONOXIDE)
WARNING
•Do not breathe exhaust gas; it contains
colorless and odorless carbon monoxide.
Carbon monoxide is dangerous. It can
cause unconsciousness or death.
•If you suspect that exhaust fumes are
entering the vehicle, drive with all win-
dows fully open, and have the vehicle
inspected immediately.
•Do not run the engine in closed spaces
such as a garage.
•Do not park the vehicle with the engine
running for an extended period of time.
•Keep the lift gate closed while driving,
otherwise exhaust gas could be drawn
into the passenger compartment. If you
must drive with the lift gate open, fol-
low these precautions:
–Open all the windows.
–Turn the air recirculation switch off
and set the fan control to the highest
level to circulate the air.
•If electrical wiring or other cable con-
nections must pass to a trailer through
the seal ion the lift gate or body, follow
the manufacturer's recommendations
to prevent carbon monoxide entry into
the vehicle.
•The exhaust system and body should be
inspected by a qualified mechanic when-
ever:
–You suspect that exhaust fumes are
entering into the passenger compart-
ment.
–You notice a change in the sound of
the exhaust system.
–You have had an accident involving
damage to the exhaust system, un-
derbody, or rear of the vehicle.
THREE-WAY CATALYST
(IF EQUIPPED)
The three-way catalyst is an emission control
device installed in the exhaust system. Ex-
haust gas in the three-way catalyst is burned
at high temperatures to help reduce pollut-
ants.
PRECAUTIONS WHEN STARTING
AND DRIVING
5-2Starting and driving
Page 239 of 436
Tire Pressure Monitoring System
warning messages
If the tire pressure monitor detects a pressure
loss in one or more tires, a warning message
is shown in the vehicle information display
and the yellow tire pressure monitor warning
light comes on.
•If the [Please Correct Tire Pressure] (yel-
low) message appears in the vehicle infor-
mation display, the tire pressure in at least
one tire is too low and must be corrected
at the next opportunity. If the system de-
tects that new sensors have been fitted
(IDs do not match those stored, and the
pressure is not feasible, or is less than 14%
under the norm then the [Please Correct
Tire Pressure] message will be displayed in
white.
•If the [Check Tires] (red) message appears
in the vehicle information display, the tire
pressure in one or more tires has dropped
significantly and the tires must be checked.
•If the [Warning Tire Malfunction] (red)
message appears in the vehicle informa-
tion display, the tire pressure in one or
more tires has dropped suddenly and the
tires must be checked.
•If the [Tire Press. Sensor(s) Missing] mes-
sage appears in the vehicle information
display, one or more sensors are missing or
cannot be detected. This could be the re-
sult of fitting a replacement wheel/tire.
Observe the instructions and safety notes in
the display messages in the vehicle informa-
tion display.
If the wheel positions on the vehicle are inter-
changed, the tire pressures may be displayed
for the wrong positions for a short time. After
a few minutes of driving, this is rectified and
the tire pressures are displayed for the cor-
rect positions.
Restarting TPMS
To keep the TPMS functioning properly, the
restart operation must be performed in the
following cases:
•When the tire pressure is adjusted
•When a tire or a wheel is replaced
•When the tires are rotated
When you restart the tire pressure monitor,
all existing warning messages are deleted
and the warning lights go out. The monitor
uses the currently set tire pressures as the
reference values for monitoring. In mostcases, the tire pressure monitor will auto-
matically detect the new reference values af-
ter you have changed the tire pressure. How-
ever, you can also define reference values
manually as described here. The tire pressure
monitor then monitors the new tire pressure
values.
Perform the following procedures to restart
the TPMS.
NOTE
Before restarting, make sure that the tire
pressures are set properly on all four tires for
the respective operating conditions. The
recommended tire pressures can be found in
the tire pressure placard on the driver' door
pillar.
1. Make sure that the ignition switch is in the
ON position.
2. Press the
orbutton on the
steering wheel to select the [Serv.] menu.
3. Press the
orbutton to select
[Tire Pressure].
4. Press
The vehicle information display shows the
current tire pressure for each tire or the
[Tire pressures will be displayed after
driving a few minutes] message.
Starting and driving5-7