display INFINITI QX56 2004 Factory Service Manual

ATC-56
TROUBLE DIAGNOSIS
Revision: August 20072004 QX56
Operational Check (Front)EJS002CB
The purpose of the operational check is to confirm that the system operates properly.
CHECKING MEMORY FUNCTION
1. Set the temperature to 90°F or 32°C.
2. Press OFF switch [hold fan (down) switch down until system
shuts OFF].
3. Turn ignition switch OFF.
4. Turn ignition switch ON.
5. Press the AUTO switch.
6. Confirm that the set temperature remains at previous tempera-
ture.
7. Press OFF switch [hold fan (down) switch down until system
shuts OFF].
If NG, go to trouble diagnosis procedure for ATC-121, "
Memory
Function" .
If OK, continue with next check.
CHECKING BLOWER
1. Press fan (up) switch. Blower should operate on low speed. The
front blower speed symbol should have one bar lit (on display).
2. Press fan (up) switch again, and continue checking blower
speed and blower symbol until all speeds are checked.
3. Leave blower on maximum speed.
If NG, go to trouble diagnosis procedure for AT C - 8 5 , "
DIAGNOSTIC
PROCEDURE FOR BLOWER MOTOR" .
If OK, continue with next check.Conditions : Engine running and at normal operating temperature
WJIA0404E
WJIA0411E
WJIA0404E
WJIA0405E

TROUBLE DIAGNOSIS
ATC-57
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: August 20072004 QX56
CHECKING DISCHARGE AIR
1. Press MODE switch four times and then rotate the DEF dial
counterclockwise.
2. Each position indicator should change shape (on display).
3. Confirm that discharge air comes out according to the air distri-
bution table. Refer to AT C - 2 9 , "
Discharge Air Flow" .
Mode door position is checked in the next step.
If NG, go to trouble diagnosis procedure for ATC-63, "
Mode Door
Motor Circuit" .
If OK, continue with next check.
NOTE:
Confirm that the compressor clutch is engaged (sound or visual
inspection) and intake door position is at fresh when the DEF or D/F
is selected.
CHECKING RECIRCULATION
1. Press recirculation ( ) switch one time. Recirculation indica-
tor should illuminate.
2. Press recirculation ( ) switch one more time. Fresh ( )
indicator should illuminate.
3. Listen for intake door position change (blower sound should
change slightly).
If NG, go to trouble diagnosis procedure for AT C - 7 6 , "
Intake Door
Motor Circuit" .
If OK, continue with next check.
NOTE:
Confirm that the compressor clutch is engaged (sound or visual
inspection) and intake door position is at fresh when the DEF or D/F is selected.
CHECKING TEMPERATURE DECREASE
1. Rotate temperature dial counterclockwise (driver or passenger)
until 18°C (60°F) is displayed.
2. Check for cold air at appropriate discharge air outlets.
If NG, listen for sound of air mix door motor operation. If OK, go to
trouble diagnosis procedure for AT C - 11 0 , "
Insufficient Cooling" . If
air mix door motor appears to be malfunctioning, go to AT C - 6 9 ,
"DIAGNOSTIC PROCEDURE FOR AIR MIX DOOR MOTOR
(DRIVER)" or AT C - 7 1 , "DIAGNOSTIC PROCEDURE FOR AIR MIX
DOOR MOTOR (PASSENGER)" .
If OK, continue with next check.
WJIA0406E
WJIA0528E
WJIA0407E
WJIA0408E

ATC-58
TROUBLE DIAGNOSIS
Revision: August 20072004 QX56
CHECKING TEMPERATURE INCREASE
1. Rotate temperature dial clockwise (driver or passenger) until
32°C (90°F) is displayed.
2. Check for hot air at appropriate discharge air outlets.
If NG, listen for sound of air mix door motor operation. If OK, go to
trouble diagnosis procedure for ATC-117, "
Insufficient Heating" . If
air mix door motor appears to be malfunctioning, go to ATC-69,
"DIAGNOSTIC PROCEDURE FOR AIR MIX DOOR MOTOR
(DRIVER)" or AT C - 7 1 , "DIAGNOSTIC PROCEDURE FOR AIR MIX
DOOR MOTOR (PASSENGER)" .
If OK, continue with next check.
CHECK A/C SWITCH
1. Press A/C switch.
2. A/C switch indicator will turn ON.

Confirm that the compressor clutch engages (sound or visual
inspection).
If NG, go to trouble diagnosis procedure for ATC-104, "
Magnet
Clutch Circuit" .
If OK, continue with next check.
CHECKING AUTO MODE
1. Press AUTO switch.
2. Display should indicate AUTO.

If ambient temperature is warm, and selected temperature is
cool, confirm that the compressor clutch engages (sound or
visual inspection). (Discharge air and blower speed will
depend on ambient, in-vehicle, and set temperatures.)
If NG, go to trouble diagnosis procedure for ATC-60, "
Power Supply
and Ground Circuit for Front Air Control" , then if necessary, trouble
diagnosis procedure for ATC-104, "
Magnet Clutch Circuit" .
If all operational checks are OK (symptom cannot be duplicated), go
to malfunction Simulation Tests in AT C - 3 5 , "
How to Perform Trouble
Diagnosis for Quick and Accurate Repair" and perform tests as out-
lined to simulate driving conditions environment. If symptom appears. Refer to ATC-35, "
How to Perform Trou-
ble Diagnosis for Quick and Accurate Repair" , AT C - 3 5 , "SYMPTOM TABLE" and perform applicable trouble
diagnosis procedures.
WJIA0409E
WJIA0410E
WJIA0411E

TROUBLE DIAGNOSIS
ATC-61
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: August 20072004 QX56
COMPONENT DESCRIPTION
Front Air Control
The front air control has a built-in microcomputer which processes
information sent from various sensors needed for air conditioner
operation. The air mix door motors, mode door motor, intake door
motor, defroster door motor, blower motor and compressor are then
controlled.
The front air control is unitized with control mechanisms. When the
various switches and temperature dials are operated, data is input to
the front air control.
Self-diagnostic functions are also built into the front air control to pro-
vide quick check of malfunctions in the auto air conditioner system.
Potentio Temperature Control (PTC)
There are two PTCs (passenger and driver) built into the front air
control. They can be set at an interval of 0.5°C (1.0°F) in the 18°C
(65°F) to 30°C (85°F) temperature range by rotating the temperature
dial. The set temperature is displayed.
DIAGNOSTIC PROCEDURE FOR A/C SYSTEM
SYMPTOM: A/C system does not come on.
WJIA0759E
WJIA0413E
WJIA0414E

REFRIGERANT LINES
ATC-181
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: August 20072004 QX56
NOTE:
Keep the probe inserted for at least 10 seconds. Use caution not to contaminate the probe tip with
water or dirt that may be in the drain hose.
5. If a leak is detected, verify at least once by blowing compressed air into the area of the suspected leak,
then repeat the leak check.
6. Do not stop when one leak is found. Continue to check for additional leaks at all system components and
connections.
7. If no leaks are found, perform steps 8 - 11.
8. Start the engine.
9. Set the heater A/C controls as follows:
NOTE:
For the automatic system, turn OFF the automatic controls and set the heater A/C controls manually.
a. A/C switch to ON
b. Air flow to VENT mode
c. Intake position to RECIRCULATION mode
d. Temperature to MAX cold
e. Fan speed to HIGH
10. Run the engine at 1,500 rpm for at least 2 minutes.
11. Turn the engine OFF and perform the leak check again following
steps 4 through 6 above.
Refrigerant leaks should be checked immediately after turning
the engine OFF. Begin with the leak detector at the compressor.
The pressure on the high pressure side will gradually drop after
the refrigerant circulation stops and pressure on the low pres-
sure side will gradually rise, as shown in the graph. Some leaks
are more easily detected when the pressure is high.
12. Before connecting the recovery/recycling equipment to the vehicle, check the recovery/recycling equip-
ment gauges. No refrigerant pressure should be displayed. If pressure is displayed, recover the refriger-
ant from the equipment lines and then check the refrigerant purity.
13. Confirm refrigerant purity in supply tank using recovery/recycling equipment and refrigerant identifier
equipment (J-41810-NI).
14. Confirm the refrigerant purity in the vehicle's A/C system using recovery/recycling equipment and refriger-
ant identifier equipment (J-41810-NI).
15. Discharge the A/C system using recovery/recycling equipment. Repair the leaking fitting or component as
necessary.
16. Evacuate and recharge the A/C system and perform the leak test to confirm that there are no refrigerant
leaks.
17. Conduct the Operational Check to ensure system works properly. Refer to ATC-56, "
Operational Check
(Front)" .
SHA8 39 E

AV-1
AUDIO, VISUAL, NAVIGATION & TELEPHONE SYS-
TEM
K ELECTRICAL
CONTENTS
C
D
E
F
G
H
I
J
L
M
SECTION AV
A
B
AV
Revision: August 20072004 QX56 PRECAUTIONS .......................................................... 4
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 4
Wiring Diagrams and Trouble Diagnosis .................. 4
PREPARATION ........................................................... 5
Commercial Service Tool ......................................... 5
AUDIO ......................................................................... 6
Component Parts and Harness Connector Location ..... 6
System Description .................................................. 7
REAR AUDIO REMOTE CONTROL UNIT ........... 7
SATELLITE RADIO TUNER (PRE-WIRING) ........ 8
SPEED SENSITIVE VOLUME SYSTEM .............. 8
Schematic ................................................................ 9
Wiring Diagram -AUDIO- ........................................ 10
Terminals and Reference Value for Audio Unit ....... 19
Terminals and Reference Value for BOSE Speaker
Amp. ....................................................................... 22
Terminals and Reference Value for Rear Audio
Remote Control Unit ............................................... 24
Terminals and Reference Value for AV Switch ....... 25
AV Switch Self-Diagnosis Function ........................ 27
STARTING THE SELF-DIAGNOSIS MODE ....... 27
EXITING THE SELF-DIAGNOSIS MODE ........... 27
DIAGNOSIS FUNCTION ..................................... 27
Trouble Diagnosis .................................................. 28
MALFUNCTION WITH RADIO AND CD ............. 28
FOR RADIO ONLY .............................................. 29
FOR CD ONLY .................................................... 30
Noise Inspection ..................................................... 30
TYPE OF NOISE AND POSSIBLE CAUSE ........ 30
Power Supply Circuit Inspection ............................ 30
Steering Switch Check ........................................... 32
AV Switch Check .................................................... 33
Audio Communication Line Check ......................... 33
Sound Is Not Heard From Front Door Speaker or
Front Tweeter ......................................................... 34
Sound Is Not Heard From Rear Door Speaker or
Rear Door Tweeter ................................................. 38
Sound Is Not Heard From Center Speaker ............ 41Sound Is Not Heard From Subwoofer .................... 42
Removal and Installation for Audio Unit ................. 45
Removal and Installation for AV Switch .................. 45
Removal and Installation of Front Door Speaker .... 45
Removal and Installation of Rear Door Speaker .... 45
Removal and Installation of Front Tweeter ............. 46
Removal and Installation of Rear Door Tweeter ..... 46
Removal and Installation of Center Speaker .......... 46
Removal and Installation of Subwoofer .................. 46
Removal and Installation of BOSE Speaker Amp. ... 46
Removal and Installation of Rear Audio Remote
Control Unit ............................................................. 47
Removal and Installation of Steering Wheel Audio
Control Switches ..................................................... 47
AUDIO ANTENNA .................................................... 48
System Description ................................................. 48
Wiring Diagram — W/ANT — ................................. 49
Location of Antenna ................................................ 50
Window Antenna Repair ......................................... 50
ELEMENT CHECK .............................................. 50
ELEMENT REPAIR ............................................. 51
DVD ENTERTAINMENT SYSTEM ............................ 52
Component Parts and Harness Connector Location ... 52
System Description ................................................. 53
Schematic ............................................................... 54
Wiring Diagram — DVD — ..................................... 55
Trouble Diagnosis ................................................... 58
Power Supply Circuit Inspection ............................. 59
Removal and Installation of DVD Player ................ 59
Removal and Installation of Video Monitor ............. 60
NAVIGATION SYSTEM ............................................. 61
System Description ................................................. 61
TRAVEL DISTANCE ............................................ 61
TRAVEL DIRECTION .......................................... 61
MAP-MATCHING ................................................. 61
GPS (GLOBAL POSITIONING SYSTEM) .......... 62
COMPONENT DESCRIPTION ............................ 63
BIRDVIEW™ ....................................................... 63
MAP DISPLAY ..................................................... 64
FUNCTION OF CENTER SWITCH ..................... 65

AV-2Revision: August 20072004 QX56 “VIEW” MODE ..................................................... 70
“HEADING” MODE .............................................. 71
“NEARBY DISPLAY ICONS” MODE ................... 71
“SAVE CURRENT LOCATION” MODE ............... 71
“ADJUST CURRENT LOCATION” MODE ........... 71
“AUTO RE-ROUTE” MODE ................................. 72
“AVOID AREA SETTINGS” MODE ...................... 72
“CLEAR MEMORY” MODE ................................. 72
“EDIT ADDRESS BOOK” MODE ........................ 73
“GPS INFORMATION” MODE ............................. 73
“QUICK STOP CUSTOMER SETTING” MODE ... 73
“SET AVERAGE SPEED” MODE ........................ 73
“TRACKING” MODE ............................................ 74
GUIDANCE VOLUME ......................................... 74
DISPLAY WITH PUSHED “TRIP” BUTTON ........ 74
TRIP 1 OR TRIP 2 ............................................... 75
FUEL ECONOMY ................................................ 75
MAINTENANCE .................................................. 75
ENGINE OIL OR TIRE ROTATION ..................... 75
TIRE PRESSURE ................................................ 76
WARNING INDICATIONS ................................... 76
CAN Communication System Description .............. 76
Component Parts Location ..................................... 77
Schematic ............................................................... 78
Wiring Diagram —NAVI— ....................................... 79
Schematic ............................................................... 86
Wiring Diagram — COMM — ................................. 87
Terminals and Reference Value for NAVI Control
unit .......................................................................... 90
Terminals and Reference Value for Display Control
unit .......................................................................... 92
Terminals and Reference Value for Display unit ..... 96
Terminals and Reference Value for AV Switch ....... 98
Terminals and Reference Value for BCM ................ 99
On Board Self-Diagnosis Function .......................101
DESCRIPTION ..................................................101
DIAGNOSIS ITEM .............................................101
Self-Diagnosis Mode (DCU) .................................101
OPERATION PROCEDURE ..............................101
SELF–DIAGNOSIS RESULT .............................103
Self-Diagnosis Mode (NAVI) .................................104
OPERATION PROCEDURE ..............................104
SELF–DIAGNOSIS RESULT .............................105
Confirmation/Adjustment Mode ............................107
OPERATION PROCEDURE ..............................107
DISPLAY DIAGNOSIS .......................................108
VEHICLE SIGNALS ...........................................108
NAVIGATION .....................................................109
DISPLAY DIAGNOSIS .......................................109
VEHICLE SIGNALS ...........................................110
HISTORY OF ERRORS ....................................110
DIAGNOSIS BY HISTORY OF ERRORS ..........110
NAVIGATION .....................................................112
CAN DIAG SUPPORT MONITOR ........................114
OPERATION PROCEDURE ..............................114
AV Switch Self-Diagnosis Function .......................115
Power Supply and Ground Circuit Check for NAVI
Control Unit ...........................................................116
Power Supply and Ground Circuit Check for Display Control Unit ...........................................................117
Power Supply and Ground Circuit Check for Display
Unit ........................................................................118
Power Supply and Ground Circuit Check for AV
Switch ................................................................... 120
Vehicle Speed Signal Check for NAVI Control Unit . 121
Vehicle Speed Signal Check for Display Control Unit . 122
Illumination Signal Check for NAVI Control Unit ... 123
Illumination Signal Check for Display Control Unit . 123
Ignition Signal Check for NAVI Control Unit .......... 123
Ignition Signal Check for Display Control Unit ...... 124
Reverse Signal Check for NAVI Control Unit ........ 124
Reverse Signal Check for Display Control Unit .... 124
AV Communication Line Check (Between Display
Control Unit and NAVI Control Unit) ...................... 125
Audio Communication Line Check (Between Dis-
play Control Unit and Audio Unit) .......................... 126
Display Communication Line Check (Between Dis-
play Control Unit and Display Unit) ....................... 128
AV Communication Line Check (Between Display
Control Unit and AV Switch) .................................. 130
CAN Communication Line Check ......................... 131
If NAVI Control Unit Detects That DVD-ROM Map
is Not Inserted ....................................................... 131
If NAVI Control Unit Detects That Inserted DVD-
ROM Map Malfunctioning or If It is Impossible to
Load Data from DVD-ROM Map ........................... 131
If Connection Between NAVI Control Unit and GPS
Antenna is Malfunctioning ..................................... 132
Operating Screen for Audio and A/C is Not Dis-
played When Showing NAVI Screen ..................... 132
Color of RGB Image is Not Proper (Only NAVI
Screen Looks Bluish) ............................................ 134
Color of RGB Image is Not Proper (Only NAVI
Screen Looks Reddish) ......................................... 135
Color of RGB Image is Not Proper (Only NAVI
Screen Looks Yellowish) ....................................... 136
Color of RGB Image is Not Proper (All Screen Looks
Bluish) ................................................................... 137
Color of RGB Image is Not Proper (All Screen Looks
Reddish) ................................................................ 138
Color of RGB Image is Not Proper (All Screen Looks
Yellowish) .............................................................. 139
NAVI Screen is Rolling .......................................... 140
Guide Sound is Not Heard .................................... 142
Screen is Not Shown ............................................ 143
A/C Screen is Not Shown (NAVI Screen is Shown) . 143
FUEL ECONOMY Screen is Not Shown ............... 143
Average Fuel Economy Displayed is Not Shown (“
*** ” is Shown) ....................................................... 143
Distance to Empty Displayed is Not Shown (“ *** ”
is Shown) .............................................................. 144
Driving Distance or Average Speed Displayed is Not
Shown (“ *** ” is Shown) ....................................... 144
WARNING DOOR OPEN Screen is Not Shown ... 144
Unable to Operate All of AV Switches (Unable to
Start Self-Diagnosis) ............................................. 145
Audio Does Not Work ........................................... 145
Navigation System Does Not Activate .................. 145

AV-3
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: August 20072004 QX56 Previous NAVI Conditions are Not Stored ............ 146
Previous Vehicle Conditions are Not Stored ........ 146
Position of Current Location Mark is Not Correct . 146
Radio Wave From GPS Satellite is Not Received . 146
Driving Test .......................................................... 147
Example of Symptoms Judged Not Malfunction .. 148
BASIC OPERATION ......................................... 148
VEHICLE MARK ............................................... 148
DESTINATION, PASSING POINTS, AND MENU
ITEMS CANNOT BE SELECTED/SET ............. 149
VOICE GUIDE ................................................... 149
ROUTE SEARCH .............................................. 150
EXAMPLES OF CURRENT-LOCATION MARK
DISPLACEMENT .............................................. 151
CURRENT LOCATION MARK SHOWS A POSI-
TION WHICH IS COMPLETELY WRONG ........ 154
CURRENT-LOCATION MARK JUMPS ............. 154
CURRENT LOCATION MARK IS IN A RIVER OR
SEA ................................................................... 155
WHEN DRIVING ON SAME ROAD, SOME-TIMES CURRENT-LOCATION MARK IS IN
RIGHT PLACE AND SOMETIMES IT IS WRONG
PLACE ...............................................................155
LOCATION CORRECTION BY MAP-MATCH-
ING IS SLOW ....................................................155
ALTHOUGH GPS RECEIVING DISPLAY IS
GREEN, VEHICLE MARK DOES NOT RETURN
TO CORRECT LOCATION ................................155
NAME OF CURRENT PLACE IS NOT DIS-
PLAYED .............................................................155
CONTENTS OF DISPLAY DIFFER FOR BIRD-
VIEW™ AND THE (FLAT) MAP SCREEN ........155
Program Loading of NAVI Control Unit .................156
Removal and Installation of NAVI Control Unit .....157
Removal and Installation of GPS Antenna ...........157
Removal and Installation of Steering Wheel Switch .157
Removal and Installation of AV Switch .................158
Removal and Installation of Display Unit ..............158
Removal and Installation of Display Control Unit . 158

AUDIO
AV-7
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: August 20072004 QX56
System DescriptionEKS007KA
Refer to Owner's Manual for audio system operating instructions.
Power is supplied at all times

through 15A fuse [No. 17, located in the fuse block (J/B)]

to subwoofer terminal 6

through 20A fuse [No. 31, located in the fuse and fusible link box]

to audio unit terminal 6

to BOSE speaker amp. terminal 1

to AV switch terminal 1 and

to display control unit terminal 1.
With the ignition switch in the ACC or ON position, power is supplied

through 10A fuse [No. 4, located in the fuse block (J/B)]

to audio unit terminal 10 and

to AV switch terminal 2 and

to display control unit terminal 10.
With the ignition switch in the ON or START position, power is supplied

through 10A fuse [No. 12, located in the fuse block (J/B)]

to display control unit terminal 12.
Ground is supplied through the case of the audio unit.
Ground is also supplied

to subwoofer terminal 5

through body grounds B7 and B19 and

to BOSE speaker amp. terminal 17

to AV switch terminal 5 and

to display unit terminal 1 and

to display control unit terminal 3

through body grounds M57, M61 and M79.
Then audio signals are supplied

through audio unit terminals 1, 2, 3, 4, 13, 14, 15 and 16

to BOSE speaker amp. terminals 23, 24, 25, 26, 27, 28, 29 and 30.
Audio signals are amplified by the BOSE speaker amp.
The amplified audio signals are supplied

through BOSE speaker amp. terminals 2, 3, 9,10,11,12, 13, 14, 15, 16, 18 and 19

to terminals + and - of front door speaker LH and RH and

to terminals + and - of front tweeter LH and RH and

to terminals + and - of center speaker and

to terminals + and - of rear door speaker LH and RH and

to terminals + and - of rear door tweeter LH and RH and

to terminals 1 and 2 of subwoofer.
When one of steering wheel audio control switches is pushed, the resistance in steering switch circuit changes
depending on which button is pushed.
REAR AUDIO REMOTE CONTROL UNIT
Power is supplied

from audio unit terminal 32

to rear audio remote control unit terminal 13.
Ground is supplied

to rear audio remote control unit terminal 15

through body grounds B117 and B132.
Audio signals are supplied

AUDIO
AV-21
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: August 20072004 QX56
44 (W) 43 (B)Audio right
channel
sound sig-
nal from sat-
ellite radio
tunerInput ONReceive audio
signalNo sound from satel-
lite radio tuner right
channel.
45 –Shield
ground
(audio sig-
nal)–– – 0V –
46 –Shield
ground
(data)–– – 0V –
48 (L) GroundSatellite
radio tuner
request to
audio unitInput ONTurn audio unit
ON 5VSatellite radio tuner
does not operate
properly.
49 (O/L) Ground Audio RX Input ONOperate audio
volume Satellite radio tuner
audio information
does not display
properly.
50 (W/L) Ground Audio TX Output ONOperate audio
volume Satellite radio tuner
audio information
does not display
properly.
65 (O/L) Ground Audio RX Input ONOperate audio
volume Audio does not oper-
ate properly.
66 (W/L) Ground Audio TX Output ONOperate audio
volume Audio does not oper-
ate properly.
67 – Shield – ON – 0VInterference and dis-
tortion heard from
speakers.
70 – Shield – – – 0VInterference and dis-
tortion heard from
speakers. Te r m i n a l
(Wire color)
ItemSignal
input/
outputCondition
Reference value
(Approx.)Example of symptom
+–Ignition
switchOperation
SKIA0177E
SKIA4403E
SKIA4402E
SKIA4403E
SKIA4402E