diagram INFINITI QX56 2004 Factory Service Manual

ALL-MODE 4WD SYSTEM
TF-13
C
E
F
G
H
I
J
K
L
MA
B
TF
Revision: August 20072004 QX56
CONTROL SYSTEM DIAGRAM
INDICATIONS OF 4WD WARNING LAMP
*: When 4WD warning lamp is ON, all the 4WD shift indicator lamps turn OFF.
CAN CommunicationEDS0017P
SYSTEM DESCRIPTION
Refer to LAN-5, "CAN COMMUNICATION" .
WDIA0075E
Condition Content 4WD warning lamp
During self-diagnosis Indicates the malfunction position by number of flickers. Flickers at malfunction mode.
Lamp check*Checks the lamp by turning ON during engine starting. After
engine starts, it turns OFF if there are no malfunctions.ON
Malfunction in 4WD system*Turns ON to indicate malfunction. When ignition switch is
turned to “OFF” or the malfunction is corrected, it turns OFF.ON
When vehicle is driven with different
diameters of front and rear tiresFlickers once every 2 seconds.
Turns OFF when ignition switch is “OFF”.Flickers once every 2 sec-
onds.
High fluid temperature in transfer unitWhen fluid temperature is high or fluid temperature sensor cir-
cuit is shorted, it flickers twice every second.
It turns OFF when fluid temperature becomes normal.Flickers twice a second.
Other than above (System is nor-
mal.)Lamp is OFF. OFF

ALL-MODE 4WD SYSTEM
TF-17
C
E
F
G
H
I
J
K
L
MA
B
TF
Revision: August 20072004 QX56
Circuit Diagram for Quick Pinpoint CheckEDS0017S
WDWA0033E

TF-18
ALL-MODE 4WD SYSTEM
Revision: August 20072004 QX56
Wiring Diagram — T/F —EDS0017T
WDWA0014E

TF-32
ON BOARD DIAGNOSTIC SYSTEM DESCRIPTION
Revision: August 20072004 QX56
6. Touch “SELF-DIAG RESULTS” on SELECT DIAG MODE
screen.
7. Self-diagnostic results are displayed.
SELF-DIAGNOSTIC ITEMS
BCIA0031E
Detected items
(Screen terms for CONSULT-II,
“SELF-DIAG RESULT” mode)Malfunction is detected when... Check items
Revolution sensor (rear)
(VHCL SPEED SEN·RR)

Signal from vehicle speed sensor 1 (installed on A/T) is
not input due to open circuit.

Improper signal is input while driving.Refer to AT- 11 2 , "
DTC P0720
VEHICLE SPEED SENSOR A/T
(REVOLUTION SENSOR)" .
4WD solenoid valve
(DUTY SOLENOID)

Proper voltage is not applied to solenoid valve due to
open or short circuit.Refer to TF-60, "
Diagnostic Proce-
dure" .
2-4WD shift solenoid valve
(2-4WD SOLENOID)Refer to TF-62, "
Diagnostic Proce-
dure" .
Tran s fe r mo to r re lay
(MOTOR RELAY)

Motor does not operate properly due to open or short cir-
cuit in transfer motor or motor relay.Refer to TF-64, "Diagnostic Proce-
dure" .
Transfer fluid temperature sensor
(FLUID TEMP SENSOR)

Signal voltage from fluid temperature sensor is abnor-
mally high (T/F fluid temperature is abnormally low)
while driving.Refer to TF-66, "Diagnostic Proce-
dure" .
Neutral-4LO switch
(N POSI SW TF)

Improper signal is input while driving.Refer to TF-69, "Diagnostic Proce-
dure" .
Clutch pressure
(CLUTCH PRESSURE)

Improper signal is input due to open or short circuit.

Malfunction occurs in clutch pressure hydraulic circuit.(*1) Refer to TF-72, "
Diagnostic
Procedure" .
Line pressure
(LINE PRESSURE)

Improper signal is input due to open or short circuit.

Malfunction occurs in line pressure hydraulic circuit.(*1) Refer to TF-74, "
Diagnostic
Procedure" .
Engine speed signal (Note 1)
(ENGINE SPEED SIG)

Engine speed is abnormally low while driving.Refer to AT- 11 5 , "DTC P0725
ENGINE SPEED SIGNAL" .
Throttle position sensor
(THRTL POSI SEN)

Signal voltage from throttle position sensor is abnormally
high.

Signal voltage from throttle position sensor is abnormally
low when closed throttle position switch is OFF.Refer to EC-351, "
DTC P0605
ECM" .
Transfer control unit (ADC)
C/U (ADC)/THRTL SEN

Power supply voltage for A/D converter system of trans-
fer control unit is malfunctioning.Refer to EC-351, "DTC P0605
ECM" .
Battery voltage (Note 1)
(BATTERY VOLTAGE)

Power supply voltage for transfer control unit is abnor-
mally low while driving.Refer to TF-18, "Wiring Diagram —
T/F —" .
4WD shift switch
(4WD MODE SW)

More than two switch inputs are simultaneously detected
due to short circuit of 4WD shift switch.Refer to TF-62, "Diagnostic Proce-
dure" .
ABS operation signal (Note 4)
(ABS OPER SIGNAL)

When a malfunction signal due to disconnection or
shorting is detected.

When a defect signal is entered from the ABS control
unit.Refer to BRC-54, "
CAN Communi-
cation System Inspection" .
Wait detection switch (Note 2)
(WAIT DETECT SWITCH)

Improper signal is input due to open or short circuit.(*2) Refer to TF-69, "Diagnostic
Procedure" .

WT-1
ROAD WHEELS & TIRES
E SUSPENSION
CONTENTS
C
D
F
G
H
I
J
K
L
M
SECTION WT
A
B
WT
Revision: August 20072004 QX56 PREPARATION ........................................................... 2
Special Service Tool ................................................. 2
Commercial Service Tools ........................................ 2
NOISE, VIBRATION, AND HARSHNESS (NVH)
TROUBLESHOOTING ................................................ 3
NVH Troubleshooting Chart ..................................... 3
WHEEL ....................................................................... 4
Inspection ................................................................. 4
WHEEL AND TIRE ASSEMBLY ................................. 5
Balancing Wheels .................................................... 5
REMOVAL ............................................................. 5
WHEEL BALANCE ADJUSTMENT ...................... 5
Rotation .................................................................... 6
LOW TIRE PRESSURE WARNING SYSTEM ............ 7
System Components ................................................ 7
System Description .................................................. 7
TRANSMITTER ..................................................... 7
REMOTE KEYLESS ENTRY RECEIVER ............. 7
BCM (BODY CONTROL MODULE) ...................... 8
LOW TIRE PRESSURE WARNING LAMP AND
BUZZER ................................................................ 8
DISPLAY UNIT ...................................................... 8
CAN COMMUNICATION ............................................ 9
System Description .................................................. 9
TROUBLE DIAGNOSES .......................................... 10
Wiring Diagram — T/WARN — .............................. 10
Terminal and Reference Value (BCM) .................... 12
ID Registration Procedure ...................................... 13
ID REGISTRATION WITH TRANSMITTER
ACTIVATION TOOL ............................................ 13
ID REGISTRATION WITHOUT TRANSMITTER
ACTIVATION TOOL ............................................ 14
Transmitter Wake Up Operation ............................. 15
............................................................................ 15
CONSULT-II Function (BCM) ................................. 16
Self-Diagnosis ........................................................ 17
DESCRIPTION .................................................... 17
FUNCTION .......................................................... 17CONSULT-II ......................................................... 17
How to Perform Trouble Diagnosis for Quick and
Accurate Repair ...................................................... 19
INTRODUCTION ................................................. 19
WORK FLOW ...................................................... 19
Preliminary Check .................................................. 20
Malfunction Code/Symptom Chart .......................... 21
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC
ITEMS ........................................................................ 23
Inspection 1: Transmitter or Control Unit (BCM) ..... 23
MALFUNCTION CODE NO. 21, 22, 23 OR 24 ... 23
Inspection 2: Transmitter - 1 ................................... 23
MALFUNCTION CODE NO. 31, 32, 33, 34, 41,
42, 43, 44, 45, 46, 47 OR 48 ............................... 23
Inspection 3: Transmitter - 2 ................................... 24
MALFUNCTION CODE NO. 35, 36, 37 OR 38 ... 24
Inspection 4: Vehicle Speed Signal ........................ 25
MALFUNCTION CODE NO. 52 ........................... 25
TROUBLE DIAGNOSIS FOR SYMPTOMS .............. 26
Inspection 1: Low Tire Pressure Warning Lamp
Does Not Come On When Ignition Switch Is Turned
On ........................................................................... 26
Inspection 2: Low Tire Pressure Warning Lamp
Stays On When Ignition Switch Is Turned On ......... 26
Inspection 3: Low Tire Pressure Warning Lamp
Flashes When Ignition Switch Is Turned On .......... 28
Inspection 4: Hazard Warning Lamp Flashes When
Ignition Switch Is Turned On .................................. 29
Inspection 5: “TIRE PRESSURE” Information In
Display Unit Does Not Exist .................................... 30
Inspection 6: ID Registration Cannot Be Completed ... 30
REMOVAL AND INSTALLATION ............................. 31
Transmitter (Pressure Sensor) ............................... 31
REMOVAL ........................................................... 31
INSTALLATION ................................................... 31
SERVICE DATA AND SPECIFICATIONS (SDS) ...... 33
Road Wheel ............................................................ 33
Tire ......................................................................... 33

WT-10
TROUBLE DIAGNOSES
Revision: August 20072004 QX56
TROUBLE DIAGNOSESPFP:00004
Wiring Diagram — T/WARN —EES00129
WEWA0044E

TROUBLE DIAGNOSES
WT-15
C
D
F
G
H
I
J
K
L
MA
B
WT
Revision: August 20072004 QX56
Transmitter Wake Up OperationEES0012C
1. With the transmitter activation tool (J-45295) pushed against the
front left transmitter, press the button for 5 seconds.

With ignition switch ON, as the low tire pressure warning lamp
flashes per the follow diagram, the respective transmitter then
must be woken up.
2. When the BCM finishes assigning each tire ID, the BCM flashes the hazard warning lamps and trailer
flasher lamps and sends flashing indicator status by CAN according to the following time chart.
3. After completing wake up of all transmitters, make sure low tire pressure warning lamp goes out.Tool number — (J-45295)
LEIA0036E
LEIA0059E

WW-1
WIPER, WASHER & HORN
K ELECTRICAL
CONTENTS
C
D
E
F
G
H
I
J
L
M
SECTION WW
A
B
WW
Revision: August 20072004 QX56 PRECAUTION ............................................................ 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 3
Wiring Diagrams and Trouble Diagnosis .................. 3
FRONT WIPER AND WASHER SYSTEM .................. 4
Components Parts and Harness Connector Loca-
tion ........................................................................... 4
System Description .................................................. 4
LOW SPEED WIPER OPERATION ...................... 5
HI SPEED WIPER OPERATION ........................... 5
INTERMITTENT OPERATION .............................. 5
AUTO STOP OPERATION .................................... 6
FRONT WASHER OPERATION ........................... 6
MIST OPERATION ................................................ 6
FAIL-SAFE FUNCTION ......................................... 6
COMBINATION SWITCH READING FUNCTION ..... 7
CAN Communication System Description ................ 7
Schematic ................................................................ 8
Wiring Diagram — WIPER — .................................. 9
Terminals and Reference Values for BCM ............. 12
Terminals and Reference Values for IPDM E/R ..... 13
Work Flow .............................................................. 13
Preliminary Inspection ............................................ 13
INSPECTION FOR POWER SUPPLY AND
GROUND CIRCUIT ............................................. 13
CONSULT-II Function (BCM) ................................. 15
CONSULT-II OPERATION .................................. 15
DATA MONITOR ................................................. 16
ACTIVE TEST ..................................................... 17
CONSULT-II Function (IPDM E/R) ......................... 17
CONSULT-II OPERATION .................................. 17
DATA MONITOR ................................................. 18
ACTIVE TEST ..................................................... 19
Trouble Diagnosis .................................................. 19
FRONT WIPER DOES NOT OPERATE ............. 19
FRONT WIPER STOP POSITION IS INCOR-
RECT .................................................................. 22
ONLY FRONT WIPER LOW DOES NOT OPER-
ATE ..................................................................... 23ONLY FRONT WIPER HI DOES NOT OPERATE ... 25
ONLY FRONT WIPER INT DOES NOT OPER-
ATE ...................................................................... 26
FRONT WIPER INTERMITTENT OPERATION
SWITCH POSITION CANNOT BE ADJUSTED ... 27
WIPERS DO NOT WIPE WHEN FRONT
WASHER OPERATES ........................................ 27
FRONT WIPERS OPERATE FOR 10 SECONDS,
STOP FOR 20 SECONDS, AND AFTER
REPEATING THIS OPERATION FIVE TIMES,
THEY BECOME INOPERATIVE ......................... 27
Removal and Installation of Front Wiper Arms,
Adjustment of Wiper Arms Stop Location ............... 29
REMOVAL ........................................................... 29
INSTALLATION ................................................... 29
Removal and Installation of Wiper Motor and Link-
age .......................................................................... 29
REMOVAL ........................................................... 29
INSTALLATION ................................................... 30
Washer Nozzle Adjustment .................................... 30
Washer Tube Layout .............................................. 31
Removal and Installation of Wiper and Washer
Switch ..................................................................... 31
REMOVAL ........................................................... 31
INSTALLATION ................................................... 31
Removal and Installation of Washer Tank .............. 31
REMOVAL ........................................................... 31
INSTALLATION ................................................... 32
Removal and Installation of Washer Motor ............. 32
REAR WIPER AND WASHER SYSTEM .................. 33
Components Parts and Harness Connector Loca-
tion .......................................................................... 33
System Description ................................................. 33
REAR WIPER OPERATION ................................ 33
INTERMITTENT OPERATION ............................ 34
AUTO STOP OPERATION .................................. 35
REAR WASHER OPERATION ............................ 35
BCM WIPER SWITCH READING FUNCTION .... 36
Wiring Diagram — WIP/R — .................................. 37
Terminals and Reference Values for BCM .............. 39

WW-2Revision: August 20072004 QX56 How to Proceed With Trouble Diagnosis ................ 41
Preliminary Inspection ............................................ 41
INSPECTION FOR POWER SUPPLY AND
GROUND CIRCUIT ............................................. 41
CONSULT-II Function (BCM) .................................. 43
CONSULT-II OPERATION ................................... 43
DATA MONITOR .................................................. 44
ACTIVE TEST ..................................................... 44
Rear Wiper Does Not Operate ............................... 45
Rear Wiper Stop Position Is Incorrect ..................... 47
Only Rear Wiper Does Not Operate ....................... 48
Only Rear Wiper Intermittent Does Not Operate .... 49
Wiper Does Not Wipe When Rear Washer Operates ... 49
Removal and Installation of Rear Wiper Arm, Adjust-
ment of Rear Wiper Arm Stop Location .................. 50
REMOVAL ........................................................... 50
INSTALLATION .................................................... 50
Removal and Installation of Rear Wiper Motor ....... 51
REMOVAL ........................................................... 51
INSTALLATION .................................................... 51Rear Washer Nozzle Adjustment ............................52
Rear Washer Tube Layout ......................................52
Removal and Installation of Rear Washer Nozzle ...52
REMOVAL ............................................................52
INSTALLATION ....................................................52
Check Valve ............................................................53
Removal and Installation of Rear Wiper and Washer
Switch .....................................................................53
Removal and Installation of Washer Tank ...............53
Removal and Installation of Washer Motor .............53
POWER SOCKET .....................................................54
Wiring Diagram — P/SCKT — ................................54
Removal and Installation of Power Sockets ............55
REMOVAL ............................................................55
INSTALLATION ....................................................55
HORN ........................................................................56
Wiring Diagram — HORN — ..................................56
Removal and Installation .........................................57
REMOVAL ............................................................57
INSTALLATION ....................................................57

PRECAUTION
WW-3
C
D
E
F
G
H
I
J
L
MA
B
WW
Revision: August 20072004 QX56
PRECAUTION PFP:00011
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
EKS007F3
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WA RN ING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Wiring Diagrams and Trouble Diagnosis EKS007F4
When you read wiring diagrams, refer to the following:

Refer to GI-15, "How to Read Wiring Diagrams" .

Refer to PG-4, "POWER SUPPLY ROUTING CIRCUIT" for power distribution circuit.
When you perform trouble diagnosis, refer to the following:

Refer to GI-11, "HOW TO FOLLOW TEST GROUPS IN TROUBLE DIAGNOSES" .

Refer to GI-27, "How to Perform Efficient Diagnosis for an Electrical Incident" .