ignition INFINITI QX56 2006 Factory Service Manual

DI-50
WARNING CHIME
Revision: November 20092006 QX56
Preliminary CheckEKS00BCV
INSPECTION FOR POWER SUPPLY AND GROUND CIRCUIT
1. CHECK FUSE AND FUSIBLE LINK
Check for blown BCM fuse or fusible link.
Refer to DI-46, "Wiring Diagram — CHIME —" .
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse. Refer to PG-
4, "POWER SUPPLY ROUTING CIRCUIT" .
2. CHECK POWER SUPPLY CIRCUIT
1. Disconnect BCM connectors M18 and M20.
2. Check voltage between BCM harness connector terminals and ground.
OK or NG
OK >> GO TO 3.
NG >> Check harness for open between BCM and fuse.
3. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Check continuity between BCM harness connector M20 terminal 67 and ground.
OK or NG
OK >> Inspection End.
NG >> Repair harness or connector.
Unit Power source Fuse or fusible link No.
BCM Battery
f
Ignition switch ON or START 59
TerminalsIgnition switch position
(+) (– )O FFO N
Connector Terminal
M20 70
GroundBattery volt-
age Battery volt-
age
M18 38 0VBattery volt-
age
WKIA2072E
Continuity should exist.
LIIA0915E

WARNING CHIMEDI-51
C
DE
F
G H
I
J
L
M A
B
DI
Revision: November 2009 2006 QX56
CONSULT-II Function (BCM)EKS00BCW
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
CONSULT-II BASIC OPERATION PROCEDURE
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carries out CAN communication.
1. With the ignition switch OFF, connect CONSULT-II and CON-
SULT-II CONVERTER to the data link connector, and turn igni-
tion switch ON.
2. Touch “START (NISSAN BASED VHCL) ”.
3. Touch “BCM” on “SELECT SYSTEM ” screen. If “BCM” is not
indicated, go to GI-40, "
CONSULT-II Data Link Connector (DLC)
Circuit" .
BCM
diagnostic test item Diagnostic mode
Description
Inspection by part WORK SUPPORT
Supports inspections and adjustments. Commands are transmitted to the BCM
for setting the status suitable for required operation, input/output signals are
received from the BCM and received data is displayed.
DATA MONITOR Displays BCM input/output data in real time. ACTIVE TEST Operation of electrical loads can be checked by sending drive signal to them.
SELF-DIAG RESULTS Displays BCM self-diagnosis results.
CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication can be read. ECU PART NUMBER BCM part number can be read.CONFIGURATION Performs BCM configuration read/write functions.
BBIA0369E
BCIA0029E
BCIA0030E

DI-52
WARNING CHIME
Revision: November 20092006 QX56
4. Touch “BUZZER” or “BCM”.
5. Select “DATA MONITOR ”, “ACTIVE TEST ” or “SELF-DIAG
RESULTS ”.
DATA MONITOR
Operation Procedure
1. Touch “BUZZER” on “SELECT TEST ITEM ” screen.
2. Touch “DATA MONITOR” on “SELECT DIAG MODE ” screen.
3. Touch “ALL SIGNALS ” or “SELECTION FROM MENU ” on “DATA MONITOR” screen.
4. If “SELECTION FROM MENU” is selected, touch the item you desire to monitor. If “ALL SIGNALS” is
selected, all control items are monitored.
5. Touch “START”.
6. During monitoring, touching “RECORD” can start recording the monitored item status.
Display Item List
ACTIVE TEST
Operation Procedure
1. Touch “BUZZER” on “SELECT TEST ITEM ” screen.
2. Touch “ACTIVE TEST ” on “SELECT DIAG MODE ” screen.
3. Touch the item to be tested, and check the operation.
4. During the operation check, touching “OFF” deactivates the operation.
SKIA5788E
BCIA0031E
ALL SIGNALS Monitors main items.
SELECTION FROM MENU Selects and monitors items.
Monitored item Description
IGN ON SW Indicates [ON/OFF] condition of ignition switch.
KEY ON SW Indicates [ON/OFF] condition of key switch.
DOOR SW-DR Indicates [ON/OFF] condition of front door switch (driver side).
LIGHT SW 1ST Indicates [ON/OFF] condition of lighting switch.

DI-54
WARNING CHIME
Revision: November 20092006 QX56
Key Warning Chime and Light Warning Chime Do Not Operate (Seat Belt Warn-
ing Chime Does Operate)
EKS00BCY
1. CHECK BCM INPUT SIGNAL
With CONSULT-II
1. Select "BCM" on CONSULT-II.
2. With "DATA MONITOR" of "BUZZER", confirm "DOOR SW-DR" changes with the status of front door LH.
Without CONSULT-II
Check voltage between BCM harness connector M19 terminal 47
and ground.
OK or NG
OK >> Replace the BCM. Refer to BCS-20, "BCM" .
NG >> GO TO 2.
2. CHECK FRONT DOOR SWITCH LH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector M19 and front door switch LH con- nector B8.
3. Check continuity between BCM harness connector M19 terminal 47 and front door switch LH harness connector B8 terminal 2.
4. Check continuity between BCM harness connector M19 terminal 47 and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair harness or connector. When front door LH is
opened
: DOOR SW-DR ON
When front door LH is
closed : DOOR SW-DR OFF
LKIA0335E
When front door LH is
opened: Approx. 0V
When front door LH is
closed : Approx. 5V
WKIA1515E
Continuity should exist.
Continuity should not exist.
WKIA1516E

WARNING CHIMEDI-55
C
DE
F
G H
I
J
L
M A
B
DI
Revision: November 2009 2006 QX56
3. CHECK FRONT DOOR SWITCH LH
Check continuity between front door switch LH terminal 2 and
exposed metal of switch while pressing and releasing switch.
OK or NG
OK >> Replace the BCM. Refer to BCS-20, "BCM" .
NG >> Replace the front door switch LH.
Key Warning Chime Does Not OperateEKS00BCZ
1. CHECK FUSE
Check if the key switch fuse [No. 19, located in the fuse block (J/B)] is blown. Refer to DI-46, "
Wiring Diagram
— CHIME —" .
Is the fuse blown?
YES >> Replace the fuse. Be sure to repair the cause of malfunction before installing new fuse.
NO >> GO TO 2.
2. CHECK WARNING CHIME OPERATION
With key removed from the ignition key cylinder and the front door LH open, turn the lighting switch to 1st or
2nd position.
Does warning chime sound?
YES >> GO TO 3.
NO >> Go to DI-53, "
All Warning Chimes Do Not Operate" or DI-54, "Key Warning Chime and Light
Warning Chime Do Not Operate (Seat Belt Warning Chime Does Operate)" .
When front door switch
LH is released
: Continuity should exist.
When front door switch
LH is pressed : Continuity should not
exist.
WKIA2023E

DI-56
WARNING CHIME
Revision: November 20092006 QX56
3. CHECK BCM INPUT SIGNAL
With CONSULT-II
With "DATA MONITOR" of "BUZZER", confirm "KEY ON SW"
changes when the key is inserted/removed from the ignition key cyl-
inder.
Without CONSULT-II
Check voltage between BCM harness connector M18 terminal 37
and ground.
OK or NG
OK >> Replace the BCM. Refer to BCS-20, "BCM" .
NG >> GO TO 4.
4. CHECK KEY SWITCH
1. Turn ignition switch OFF.
2. Disconnect key switch and key lock solenoid connector.
3. Check continuity between key switch and key lock solenoid ter- minals 3 and 4.
OK or NG
OK >> GO TO 5.
NG >> Replace the key switch and key lock solenoid. When key is inserted in ignition
key cylinder
: KEY ON SW ON
When key is removed from
ignition key cylinder : KEY ON SW OFF
SKIA1960E
Terminals
Condition Voltage (V)
(+)
(– )
Connector Terminal
M18 37 Ground Key is inserted Battery voltage
Key is removed
0
LKIA0255E
TerminalsConditionContinuity
34 Key is inserted
Yes
Key is removed No
WKIA1820E

DI-58
WARNING CHIME
Revision: November 20092006 QX56
Seat Belt Warning Chime Does Not OperateEKS00BD1
1. CHECK WARNING CHIME OPERATION
1. With key removed from the ignition and the front door LH open, turn the lighting switch to 1st or 2nd posi- tion.
2. Return lighting switch to OFF position, and insert key into ignition.
Does warning chime sound for both steps?
YES >> GO TO 2.
NO >> Go to DI-53, "
All Warning Chimes Do Not Operate" .
2. CHECK SEAT BELT WARNING LAMP OPERATION
Turn ignition switch ON. Buckle and unbuckle the driver seat belt while watching seat belt warning lamp.
OK or NG
OK >> Replace the BCM. Refer to BCS-20, "BCM" .
NG >> GO TO 3.
3. CHECK COMBINATION METER INPUT SIGNAL
1. Turn ignition switch ON.
2. Check voltage between combination meter harness connector M24 terminal 27 and ground.
OK or NG
OK >> Replace the combination meter. Refer to IP-13, "COMBINATION METER" .
NG >> GO TO 4.
4. CHECK SEAT BELT BUCKLE SWITCH
1. Turn ignition switch OFF.
2. Disconnect seat belt buckle pre-tensioner assembly LH (seat belt buckle switch) connector.
3. Check continuity between seat belt buckle pre-tensioner assem- bly LH (seat belt buckle switch) terminals 3 and 4.
OK or NG
OK >> GO TO 5.
NG >> Replace the seat belt buckle pre-tensioner assembly LH (seat belt buckle switch). When seat belt is fastened : Warning lamp OFF
When seat belt is unfastened : Warning lamp ON
Te r m i n a l s
ConditionVoltage (V)
(Approx.)
(+)
(– )
Connector Terminal
M24 27 Ground Seat belt is fastened Battery voltage
Seat belt is unfastened
0
WKIA1821E
TerminalsConditionContinuity
34 Seat belt is fastened
No
Seat belt is unfastened Yes
WKIA4404E

REAR SONAR SYSTEMDI-61
C
DE
F
G H
I
J
L
M A
B
DI
Revision: November 2009 2006 QX56
System DescriptionEKS00BD3
FUNCTION
With the ignition switch in the ON or START position, power is supplied

through 10A fuse [No. 12 , located in the fuse block (J/B)]

to sonar control unit terminal 8, and

through 10A fuse (No. 51, located in the IPDM E/R)

to back-up lamp relay terminals 1 and 3.
Ground is supplied

to sonar control unit terminal 6

through body grounds B7 and B19.
With the ignition switch in the ON or START position, and the transmission gear selector lever in the R posi-
tion, power is supplied

to sonar control unit terminal 5

from back-up lamp relay terminal 5.
With power and ground supplied, transmission gear selector lever in R position, and the rear sonar system
OFF switch ON, the rear sonar system will detect obstacles within 1.8 m (5.9 ft.) of the rear sonar sensors.
The vehicle operator is notified of obstacles by varied rate of tone from the sonar buzzer depending on dis-
tance of obstacle being sensed.
REAR SONAR SYSTEM OFF SWITCH
With power and ground supplied to the sonar control unit, transmission gear selector lever in R position, the
sonar system can be disabled and the sonar buzzer silenced by momentarily pressing the rear sonar system
OFF switch. The rear sonar system OFF indicator lamp will be illuminated in the rear sonar system OFF
switch.
To disable the rear sonar system, ground is supplied

to sonar control unit terminal 13

through rear sonar system OFF switch terminal 1

through rear sonar system OFF switch terminal 2

from body grounds M57, M61, and M79.
To light the rear sonar system OFF indicator, power is supplied

from sonar control unit terminal 4

to the rear sonar system OFF switch terminal 5.
Ground is supplied

to the rear sonar system OFF switch terminal 6

from body grounds M57, M61, and M79.
The rear sonar system and buzzer will be disabled and the rear sonar system OFF indicator will be illuminated
until the ignition switch is turned OFF. When the ignition switch is turned ON, the rear sonar system will be
enabled. Depressing the rear sonar system OFF switch momentarily will enable the rear sonar system also.
Enabling the rear sonar system will cause the rear sonar system OFF indicator to go out.
SONAR BUZZER
With power supplied to the sonar control unit and the transmission gear selector lever in R position, a station-
ary object that is at least 7.0 cm (2.8 in.) wide and 1.0 m (39.0 in.) tall and that is closer than 1.8 meters (5.9 ft.)
will be detected by the rear sonar sensors, causing the sonar buzzer to sound a tone. As the vehicle moves
closer to the object, the rate of the tone will increase. When the object is less than 25.0 cm (10 in.) from the
rear bumper, the tone will sound continuously.
Power is supplied

to sonar buzzer terminal 1

from sonar control unit terminal 7.
Ground is supplied

to sonar buzzer terminal 2

from sonar control unit terminal 3.

REAR SONAR SYSTEMDI-65
C
DE
F
G H
I
J
L
M A
B
DI
Revision: November 2009 2006 QX56
Terminals And Reference Value For Sonar Control UnitEKS00BD5
How to Proceed With Trouble DiagnosisEKS00BD6
1. Confirm the symptom or customer complaint.
2. Understand operation description and function description. Refer to DI-61, "
System Description" .
3. Perform pre-diagnosis inspection. Refer to DI-66, "
Pre-diagnosis Inspection" .
4. Perform self-diagnosis. Refer to DI-66, "
Self-diagnosis Function" .
5. Perform the preliminary check. Refer to DI-68, "
Preliminary Check" .
6. Check symptom and repair or replace the cause of malfunction. Refer to DI-69, "
Symptom Chart" .
7. Does the rear sonar system operate properly? If so, go to 8. If not, go to 3.
8. Clear fault codes. Refer to DI-67, "
IDLING OR CLEARING FAULT CODES MODE" .
9. Inspection End.
TERMINAL (COLOR) ITEM CONDITION
Reference value (V)
(Approx.)
IGNITION
SWITCH OPERATION
3 (R) Sonar buzzer return ON —0 - 12 (variable)
4 (BR/Y) Rear sonar system
OFF indicator output ONRear sonar system OFF
switch ON
0
OFF 12
5 (G/W) Reverse signal ONTransmission gear
selector lever
R position
12
Transmission gear
selector lever Not R position
0
6 (B) Sonar control unit
ground ——
0
7 (L) Sonar buzzer drive signal ON
— 12
8 (G/R) Sonar control unit
power
ON
— 12
9 (GR) Rear sonar sensor
signal - RH outer ON

Rear sonar system OFF switch ON

Transmission gear selector lever in R
position

No obstacles 12
10 (P) Rear sonar sensor
signal - LH outer ON

Rear sonar system OFF switch ON

Transmission gear selector lever in R
position

No obstacles 12
11 ( O ) Rear sonar sensor
signal - LH inner ON

Rear sonar system OFF switch ON

Transmission gear selector lever in R
position

Distance obstacles 12
12 (LG) Rear sonar sensor
signal - RH inner ON

Rear sonar system OFF switch ON

Transmission gear selector lever in R
position

Distance obstacles 12
13 (LG) Rear sonar system
OFF switch signal ONRear sonar system OFF
switch ON
0
OFF 12
15 (Y) Rear sonar sensor
ground ON
— 0
16 (LG/B) Rear sonar sensor
power ON Ignition switch ON
12

DI-66
REAR SONAR SYSTEM
Revision: November 20092006 QX56
Pre-diagnosis InspectionEKS00BD7
SENSOR STATUS CHECK

Check that the rear sonar sensor is properly aligned (bumper is not misaligned, no deformation in sensor
mounting area.

Check that snow, mud, or other foreign objects are not adhering to the rear sonar sensor.

Check that there is no deformation, scratches, or other damage to the rear sonar sensor.

Check that water has not accumulated in the rear sonar sensor.
CAUTION:
Use water, cotton swab, or other soft material for cleaning the sensor.
1. Check that there are no obstacles within each rear sonar sensor's detection range.
2. Check that there are no nearby ultrasound sources (such as the sounds of vehicle horns, motorcycle engines, or truck air brakes).
3. Check that the vehicle is on a level surface.
Self-diagnosis FunctionEKS00BD8
There are four modes of self-diagnosis; entering diagnostics, requesting number of fault codes, requesting
fault codes, and idling or clearing fault codes. These steps must be followed in order. Self-diagnosis can be
manually exited by turning the ignition switch OFF, or selecting reverse gear. Self-diagnosis will exit unless a
fault code request occurs before a message is repeated five times without acknowledgement.
ENTERING DIAGNOSTICS MODE
1. Turn ignition switch ON. Rear sonar system OFF switch indica- tor lamp illuminates for three seconds and then turns off.
2. Immediately push rear sonar system OFF switch ten times within five seconds.
3. The sonar buzzer will sound once and the rear sonar system OFF indicator will flash once.
REQUESTING NUMBER OF FAULT CODES MODE
1. While in diagnostic mode, push rear sonar system OFF switch
once.
2. The sonar buzzer will sound once.
3. Rear sonar system OFF indicator will flash once and sonar buzzer will sound once for each fault code detected.
4. There will be a four second pause.
5. The number of fault codes will repeat five times then pause. NOTE:
Self-diagnosis will exit unless requesting fault codes occurs
before five repeats ends.
Detection range
Rear sonar sensors Approx. 1.8 m (5.9 ft.) maximum
LKIA0389E
LKIA0388E