lock INFINITI QX56 2006 Factory Workshop Manual

AT-222
A/T SHIFT LOCK SYSTEM
Revision: November 20092006 QX56
Wiring Diagram — A/T — SHIFTECS00ENW
BCWA0502E

A/T SHIFT LOCK SYSTEMAT-223
DE
F
G H
I
J
K L
M A
B
AT
Revision: November 2009 2006 QX56
Shift Lock Control Unit Reference ValuesECS00ENX
SHIFT LOCK HARNESS CONNECTOR TERMINALS LAYOUT
SHIFT LOCK CONTROL UNIT INSPECTION TABLE
Data are reference values.
NOTE:
Confirm that the pointer swings only momentarily because the output time is so short. If the inspection is done with an oscillo scope, it
should be observed that the power source voltage lasts for 3.5 to 10 ms.
WCIA0550E
TER-
MINAL NO. WIRE
COLOR ITEM
CONDITION VOLTAGE
(Approx.)
1Y/RPower source Ignition switch:
“ON ” Battery voltage
Ignition switch: “OFF ” Battery voltage
2L/R Detention switch (for
key) When selector lever is not in "P" position with key inserted. Battery voltage
Except the above
0V
3GR Detention switch (for
shift) When selector lever is not in "P" position
Battery voltage
Except the above 0V
4 R/G Stop lamp switch When brake pedal is depressed
Battery voltage
When brake pedal is released 0V
5 W/R Vehicle speed signal ——
6 G/R Ignition signal Ignition switch:
“OFF ” 0V
Ignition switch: “ON ” Battery voltage
7 R/W Shift lock solenoid When brake pedal is depressed with ignition switch "ON". 0V
When brake pedal is depressed.
Battery voltage
8 B Ground Always0V
9 G/W Key lock solenoid When the selector lever is set to a position other than the “
P”
position, and the key switch is turned from “ON ” to “OFF ” Battery voltage for
approx. 0.1 sec.
(Note)
Except the above 0V
10 W/G Key unlock solenoid When ignition switch is not in "ON
” position with key inserted. Battery voltage for
approx. 0.1 sec.
(Note)
Except the above 0V

AT-224
A/T SHIFT LOCK SYSTEM
Revision: November 20092006 QX56
Component InspectionECS00ENY
SHIFT LOCK SOLENOID

Check operation by applying battery voltage to A/T device termi-
nal 9 and ground to terminal 10.
CAUTION:
Be sure to apply the voltage of the correct polarity to the
respective terminals. Otherwise, the part may be damaged.
DETENTION SWITCH
For key:

Check continuity between terminals of the A/T device.
DETENTION SWITCH
For shift:

Check continuity between terminals of the A/T device.
KEY LOCK SOLENOID
Key lock

Check operation by applying battery voltage to key switch and
key lock solenoid terminal 1 and ground to terminal 2.
CAUTION:
Be careful not to cause burnout of the harness.
LCIA0328E
Condition Terminal No. Continuity
When selector lever is “ P” position.
5 - 6No
When selector lever is not “P ” position. Yes
LIIA1599E
ConditionTerminal No. Continuity
When selector lever is “P ” position.
3 - 4No
When selector lever is not “P ” position. Yes
WCIA0401E
WCIA0240E

A/T SHIFT LOCK SYSTEMAT-225
DE
F
G H
I
J
K L
M A
B
AT
Revision: November 2009 2006 QX56
Key unlock

Check operation by applying battery voltage to key switch and
key lock solenoid terminal 2 and ground to terminal 1.
CAUTION:
Be careful not to cause burnout of the harness.
KEY SWITCH

Check continuity between terminals of the key switch and key
lock solenoid.
STOP LAMP SWITCH

Check continuity between terminals of the stop lamp switch har-
ness connector.
Check stop lamp switch after adjusting brake pedal.
WCIA0241E
Condition Terminal No. Continuity
Key inserted 3 - 4Ye s
Key withdrawn No
SCIA5662E
ConditionTerminal No. Continuity
When brake pedal is depressed 3 - 4Ye s
When brake pedal is released No
WCIA0559E

AT-226
SHIFT CONTROL SYSTEM
Revision: November 20092006 QX56
SHIFT CONTROL SYSTEMPFP:34901
Control Device Removal and InstallationECS00ENZ
1. Select lever knob2. A/T console finisher3. Control device assembly
4. Position lamp 5. A/T selector control cable6. Lock plate
LCIA0348E

SHIFT CONTROL SYSTEMAT-227
DE
F
G H
I
J
K L
M A
B
AT
Revision: November 2009 2006 QX56
REMOVAL
1. Remove negative battery terminal. Refer to SC-4, "BATTERY" .
2. Remove A/T finisher. Refer to IP-13, "
A/T FINISHER" .
3. Disconnect selector control cable.
4. Disconnect A/T device harness connector.
5. Remove control device assembly.
INSTALLATION
Installation is in reverse order of removal. Be careful of the following:

After installation is completed, adjust and check A/T position.
Adjustment of A/T PositionECS00EO0
1. Loosen nut of control cable.
2. Place PNP switch and selector lever in “P” position.
3. After pushing the control cable in the direction shown with a force of 9.8 N ·m (1kg-m, 2.2 lb-ft), release it. This is in the natu-
ral state, tighten control cable nut to specifications.
Checking of A/T PositionECS00EO1
1. Place selector lever in “P” position, and turn ignition switch ON
(engine stop).
2. Make sure selector lever can be shifted to other than “P” posi-
tion when brake pedal is depressed. Also make sure selector
lever can be shifted from “P” position only when brake pedal is
depressed.
3. Move the selector lever and check for excessive effort, sticking, noise or rattle.
4. Confirm the selector lever stops at each position with the feel of engagement when it is moved through all the positions. Check
whether or not the actual position the selector lever is in
matches the position shown by the shift position indicator and
the transmission body.
5. The method of operating the lever to individual positions correctly should be as shown.
6. Confirm the back-up lamps illuminate only when lever is placed in the “R” position. Confirm the back-up
lamps does not illuminate when selector lever is pushed against “R” position in the “P” or “N” position.
7. Confirm the engine can only be started with the selector lever in the “P” and “N” positions.
8. Make sure transmission is locked completely in “P” position.
Control cable nut : 14.5 N·m (1.5 kg-m, 11 ft-lb)
LCIA0345E
LCIA0325E

AIR BREATHER HOSEAT-241
DE
F
G H
I
J
K L
M A
B
AT
Revision: November 2009 2006 QX56
AIR BREATHER HOSEPFP:31098
Removal and InstallationECS00EO5
2WD
CAUTION:

When installing an air breather hose, do not crush or block by folding or bending the hose.

When inserting a hose to the transmission tube, be sure to insert it fully until its end reaches the
tube bend portion.
LCIA0331E

AT-242
AIR BREATHER HOSE
Revision: November 20092006 QX56
4WD
CAUTION:

When installing an air breather hose, do not crush or block by folding or bending the hose.

When inserting a hose to the transmission tube, be sure to insert it fully until its end reaches the
tube bend portion.
LCIA0332E

AT-244
TRANSMISSION ASSEMBLY
Revision: November 20092006 QX56
8. Remove crankshaft position sensor (POS) from A/T assembly.
CAUTION:

Do not subject it to impact by dropping or hitting it.

Do not disassemble.

Do not allow metal filings or foreign material to get on the
sensor front edge magnetic area.

Do not place in an area affected by magnetism.
9. Remove fluid cooler tube.
10. Remove dust cover from converter housing.
11. Turn crankshaft to access and remove the four bolts for drive plate and torque converter.
CAUTION:
When turning crankshaft, turn it clockwise as viewed from
the front of the engine.
12. Support A/T assembly with a transmission jack. CAUTION:
When setting the transmission jack, be careful not to allow
it to collide against the drain plug.
13. Remove cross member using power tool.
14. Remove air breather hose. Refer to AT- 2 4 1 , "
Removal and
Installation" .
15. Disconnect A/T assembly connector.
16. Remove A/T fluid indicator pipe from A/T assembly.
17. Plug any openings such as the A/T fluid indicator pipe hole.
18. Remove the A/T assembly to engine bolts using power tool.
19. Remove A/T assembly from vehicle using transmission jack. CAUTION:

Secure torque converter to prevent it from dropping.

Secure A/T assembly to a transmission jack.
INSPECTION
Installation and Inspection of Torque Converter

After inserting a torque converter to a transmission, be sure to
check dimension A to ensure it is within specifications.
LCIA0334E
LCIA0335E
SCIA0499E
Dimension A : 24.0 mm (0.94 in) or more
SAT017B

TRANSMISSION ASSEMBLYAT-245
DE
F
G H
I
J
K L
M A
B
AT
Revision: November 2009 2006 QX56
INSTALLATION
Installation of the remaining components is in the reverse order of the removal, while paying attention to the
following:

When installing transmission to the engine, attach the bolts as shown.
NOTE:
*: No.2 bolt also secures air breather vent.
CAUTION:

When replacing an engine or transmission you must
make sure the dowels are installed correctly during re-
assembly.

Improper alignment caused by missing dowels may
cause vibration, oil leaks or breakage of drivetrain com-
ponents.

Align the positions of bolts for drive plate with those of the torque
converter, and temporarily tighten the bolts. Then tighten the
bolts with the specified torque.
CAUTION:

When turning crankshaft, turn it clockwise as viewed from
the front of the engine.

After converter is installed to drive plate, rotate crankshaft
several turns and check to be sure that transmission
rotates freely without binding.

Install crankshaft position sensor (POS).

After completing installation check fluid leakage, fluid level and
the positions of A/T. Refer to AT- 1 2 , "
Checking Automatic Transmission Fluid (ATF)" , AT- 2 2 7 , "Checking
of A/T Position" and AT- 2 2 7 , "Adjustment of A/T Position" .
Transmission to engine bolts : 113 N·m (12 kg-m,
83 ft-lb)
LCIA0371E
LCIA0335E