key battery INFINITI QX56 2006 Factory Service Manual
[x] Cancel search | Manufacturer: INFINITI, Model Year: 2006, Model line: QX56, Model: INFINITI QX56 2006Pages: 3383, PDF Size: 51.76 MB
Page 298 of 3383
A/T SHIFT LOCK SYSTEMAT-223
DE
F
G H
I
J
K L
M A
B
AT
Revision: November 2009 2006 QX56
Shift Lock Control Unit Reference ValuesECS00ENX
SHIFT LOCK HARNESS CONNECTOR TERMINALS LAYOUT
SHIFT LOCK CONTROL UNIT INSPECTION TABLE
Data are reference values.
NOTE:
Confirm that the pointer swings only momentarily because the output time is so short. If the inspection is done with an oscillo scope, it
should be observed that the power source voltage lasts for 3.5 to 10 ms.
WCIA0550E
TER-
MINAL NO. WIRE
COLOR ITEM
CONDITION VOLTAGE
(Approx.)
1Y/RPower source Ignition switch:
“ON ” Battery voltage
Ignition switch: “OFF ” Battery voltage
2L/R Detention switch (for
key) When selector lever is not in "P" position with key inserted. Battery voltage
Except the above
0V
3GR Detention switch (for
shift) When selector lever is not in "P" position
Battery voltage
Except the above 0V
4 R/G Stop lamp switch When brake pedal is depressed
Battery voltage
When brake pedal is released 0V
5 W/R Vehicle speed signal ——
6 G/R Ignition signal Ignition switch:
“OFF ” 0V
Ignition switch: “ON ” Battery voltage
7 R/W Shift lock solenoid When brake pedal is depressed with ignition switch "ON". 0V
When brake pedal is depressed.
Battery voltage
8 B Ground Always0V
9 G/W Key lock solenoid When the selector lever is set to a position other than the “
P”
position, and the key switch is turned from “ON ” to “OFF ” Battery voltage for
approx. 0.1 sec.
(Note)
Except the above 0V
10 W/G Key unlock solenoid When ignition switch is not in "ON
” position with key inserted. Battery voltage for
approx. 0.1 sec.
(Note)
Except the above 0V
Page 299 of 3383
AT-224
A/T SHIFT LOCK SYSTEM
Revision: November 20092006 QX56
Component InspectionECS00ENY
SHIFT LOCK SOLENOID
Check operation by applying battery voltage to A/T device termi-
nal 9 and ground to terminal 10.
CAUTION:
Be sure to apply the voltage of the correct polarity to the
respective terminals. Otherwise, the part may be damaged.
DETENTION SWITCH
For key:
Check continuity between terminals of the A/T device.
DETENTION SWITCH
For shift:
Check continuity between terminals of the A/T device.
KEY LOCK SOLENOID
Key lock
Check operation by applying battery voltage to key switch and
key lock solenoid terminal 1 and ground to terminal 2.
CAUTION:
Be careful not to cause burnout of the harness.
LCIA0328E
Condition Terminal No. Continuity
When selector lever is “ P” position.
5 - 6No
When selector lever is not “P ” position. Yes
LIIA1599E
ConditionTerminal No. Continuity
When selector lever is “P ” position.
3 - 4No
When selector lever is not “P ” position. Yes
WCIA0401E
WCIA0240E
Page 300 of 3383
A/T SHIFT LOCK SYSTEMAT-225
DE
F
G H
I
J
K L
M A
B
AT
Revision: November 2009 2006 QX56
Key unlock
Check operation by applying battery voltage to key switch and
key lock solenoid terminal 2 and ground to terminal 1.
CAUTION:
Be careful not to cause burnout of the harness.
KEY SWITCH
Check continuity between terminals of the key switch and key
lock solenoid.
STOP LAMP SWITCH
Check continuity between terminals of the stop lamp switch har-
ness connector.
Check stop lamp switch after adjusting brake pedal.
WCIA0241E
Condition Terminal No. Continuity
Key inserted 3 - 4Ye s
Key withdrawn No
SCIA5662E
ConditionTerminal No. Continuity
When brake pedal is depressed 3 - 4Ye s
When brake pedal is released No
WCIA0559E
Page 768 of 3383
BCM (BODY CONTROL MODULE)BCS-7
C
DE
F
G H
I
J
L
M A
B
BCS
Revision: November 2009 2006 QX56
BCM is activated with low current consumption mode.
CAN communication is not active.
When CAN communication operation is detected, it switches to CAN communication status.
When a state of the following switches changes, it switches to CAN communication state:
–Ignition switch
–Key switch (insert)
–Hazard switch
–Main door lock/unlock switch
–Front door switch (LH, RH)
–Rear door switch (LH, RH)
–Back latch (door ajar switch)
–Glass hatch ajar switch
–Combination switch (passing, lighting switch 1st position, front fog lamp)
–Keyfob (lock/unlock signal)
–Front door lock assembly LH (key cylinder switch)
When control performed only by BCM is required by switch, it shifts to CAN communication inactive
mode.
Status of combination switch reading function is changed.
SYSTEMS CONTROLLED BY BCM DIRECTLY
Power door lock system. Refer to BL-16, "POWER DOOR LOCK SYSTEM" .
Remote keyless entry system. Refer to BL-44, "REMOTE KEYLESS ENTRY SYSTEM" .
Power window system. Refer to GW-15, "POWER WINDOW SYSTEM" . NOTE
Sunroof system. Refer to RF-10, "SUNROOF" . NOTE
Room lamp timer. Refer to LT- 1 3 4 , "INTERIOR ROOM LAMP" .
Warning chime system. Refer to DI-43, "WARNING CHIME" .
Turn signal and hazard warning lamps system. Refer to LT- 8 0 , "TURN SIGNAL AND HAZARD WARNING
LAMPS" .
Trailer turn signal and hazard warning lamps system (if equipped). Refer to LT- 1 2 6 , "TRAILER TOW" .
Rear wiper and washer system. Refer to WW-32, "REAR WIPER AND WASHER SYSTEM" .
NOTE:
Power supply only. No system control.
SYSTEMS CONTROLLED BY BCM AND IPDM E/R
Panic system. Refer to BL-44, "REMOTE KEYLESS ENTRY SYSTEM" .
Vehicle security system. Refer to BL-75, "VEHICLE SECURITY (THEFT WARNING) SYSTEM" .
IVIS (NATS) system. Refer to BL-137, "IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-NATS)" .
Headlamp, tail lamp, front fog lamp, auto light and battery saver control systems. Refer to LT- 5 , "HEAD-
LAMP (FOR USA)" , LT- 3 3 , "HEADLAMP (FOR CANADA) - DAYTIME LIGHT SYSTEM -" , LT- 111 ,
"PARKING, LICENSE PLATE AND TAIL LAMPS" , LT- 6 9 , "FRONT FOG LAMP" or LT- 4 7 , "AUTO LIGHT
SYSTEM" .
Front wiper and washer system. Refer to WW-4, "FRONT WIPER AND WASHER SYSTEM" .
Rear window defogger system. Refer to GW-74, "REAR WINDOW DEFOGGER" .
MAJOR COMPONENTS AND CONTROL SYSTEM
System InputOutput
Remote keyless entry system Remote keyless entry receiver (keyfob)
All door locking actuators
Back door opener actuator
Turn signal lamps
Power door lock system
Front power door lock/unlock switch (LH, RH)
All door switches
Key switch All door locking actuators
Page 769 of 3383
BCS-8
BCM (BODY CONTROL MODULE)
Revision: November 20092006 QX56
CAN Communication System DescriptionEKS00D7X
Refer to LAN-26, "CAN COMMUNICATION" .
Power supply [ignition (IGN)/retained
accessory power (RAP)] to power win-
dow and sunroof IGN/RAP supply
Power supply to power window and
sunroof system
Power supply (BAT) to power window
and sunroof Battery power supply Power supply to power window and
sunroof system
Panic alarm
Key switch
Remote keyless entry receiver (keyfob) IPDM E/R
Auto light system
Optical sensor
Combination switch IPDM E/R
Battery saver control
Ignition switch
Combination switch
Front door switch LH and RH IPDM E/R
Headlamp Combination switch IPDM E/R
Tail lamp Combination switch IPDM E/R
Front fog lamp Combination switch IPDM E/R
Turn signal lamp Combination switch
Turn signal lamp
Combination meter
Hazard lamp Hazard switch
Turn signal lamp
Combination meter
Room lamp timer
Key switch
Remote keyless entry receiver (keyfob)
Main power window and door lock/unlock switch
Front door lock assembly LH (key cylinder switch)
All door switches Interior room lamp
Key warning chime
Key switch
Front door switch LH Combination meter (warning
buzzer)
Light warning chime
Combination switch
Key switch
Front door switch LH Combination meter (warning
buzzer)
Vehicle-speed-sensing intermittent
wiper
Combination switch
Combination meter IPDM E/R
Rear window defogger Rear window defogger switch IPDM E/R
Air conditioner switch signal Front air control ECM
Blower fan switch signal Front air control ECM
Low tire pressure warning system Remote keyless entry receiver
Combination meter
Display control unit
Trailer tow (if equipped) Combination switch Trailer turn signal relays
Vehicle security system
Remote keyless entry receiver (keyfob)
Main power window and door lock/unlock switch
Power window and door lock/unlock switch RH
Front door lock assembly LH (key cylinder switch)
All door switches
Back door latch (door ajar switch)
IPDM E/R
Security indicator lamp
System
InputOutput
Page 773 of 3383
BCS-12
BCM (BODY CONTROL MODULE)
Revision: November 20092006 QX56
4. Select item to be diagnosed on “SELECT TEST ITEM” screen.
ITEMS OF EACH PART
NOTE:
CONSULT-II will only display systems the vehicle possesses.
LKIA0183E
System and item CONSULT-II
display Diagnostic test mode (Inspection by part)
WORK
SUPPORT SELF−
DIAG
RESULTS CAN DIAG
SUPPORT MNTR DATA
MONITOR ECU
PA R T
NUMBER ACTIVE
TEST CON-
FIGU-
RATION
BCM BCM××× × ×
Power door lock system DOOR LOCK ×× ×
Rear defogger REAR
DEFOGGER ××
Warning chime BUZZER ××
Room lamp timer INT LAMP ×× ×
Remote keyless entry
system MULTI REMOTE
ENT
××
×
Headlamp HEAD LAMP×× ×
Wiper (front/rear) WIPER ×× ×
Turn signal lamp
Hazard lamp FLASHER
××
Blower fan switch signal
Air conditioner switch
signal AIR
CONDITIONER
×
Combination switch COMB SW ×
IVIS (NATS) IMMU ××
Interior lamp battery
saver BATTERY
SAVER
××
×
Back door TRUNK ××
Theft alarm THEFT ALM×× ×
Retained accessory
power control RETAINED PWR
×× ×
Oil pressure switch SIGNAL BUFFER ××
Air pressure monitor AIR PRESSURE
MONITOR××
× ×
Panic alarm PANIC ALARM ×
Page 781 of 3383
BCS-20
BCM (BODY CONTROL MODULE)
Revision: November 20092006 QX56
BCMEKS00D82
REMOVAL AND INSTALLATION
NOTE:
If possible, before removing BCM, retrieve current BCM configuration to use for reference when configuring
brand-new BCM after installation. Refer to BCS-14, "
Configuration" .
Removal
1. Disconnect battery negative terminal.
2. Remove instrument lower panel LH. Refer to IP-13, "
INSTRUMENT LOWER COVER LH" .
3. Remove knee protector. IP-10, "
INSTRUMENT PANEL ASSEMBLY" .
4. Disconnect BCM electrical connectors.
5. Remove BCM screws and remove BCM.
Installation
Installation is in the reverse order of removal.
NOTE:
When replacing BCM, it must be configured. Refer to BCS-14, "Configuration" .
When replacing BCM, perform initialization of NATS system and registration of all NATS ignition key IDs.
Refer to BL-137, "
IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-NATS)" .
When replacing BCM, perform ID registration procedure of low tire pressure warning system. Refer to
WT-14, "
ID Registration Procedure" .
LEIA0068E
Page 783 of 3383
BL-2Revision: November 20092006 QX56
BCM Power Supply and Ground Circuit Check ...
... 59
Trouble Diagnoses ............................................... ... 60
SYMPTOM CHART ............................................. 60
Key Switch (Insert) Check ...................................... 62
Door Switch Check .............................................. ... 63
Keyfob Battery and Function Check .................... ... 65
Remote Keyless Entry Receiver System Check .. ... 66
ACC Power Check ............................................... ... 68
IPDM E/R Operation Check ................................. ... 68
Check Hazard Function ....................................... ... 70
Check Horn Function ........................................... ... 70
Check Headlamp Function .................................. ... 70
Check Map Lamp Illumination Function .............. ... 70
ID Code Entry Procedure .................................... ... 71
KEYFOB ID SET UP WITH CONSULT-II ......... ... 71
KEYFOB ID SET UP WITHOUT CONSULT-II .. ... 73
Keyfob Battery Replacement ............................... ... 74
VEHICLE SECURITY (THEFT WARNING) SYSTEM ... 75
Component Parts and Harness Connector Location ... 75
System Description .............................................. ... 76
DESCRIPTION ................................................. ... 76
POWER SUPPLY AND GROUND CIRCUIT .... ... 77
INITIAL CONDITION TO ACTIVATE THE SYS-
TEM .................................................................. ... 77
VEHICLE SECURITY SYSTEM ALARM OPER-
ATION ............................................................... ... 77
VEHICLE SECURITY SYSTEM DEACTIVATION ... 78
PANIC ALARM OPERATION ............................ ... 78
CAN Communication System Description ........... ... 78
Schematic ............................................................ ... 79
Wiring Diagram — VEHSEC — ........................... ... 80
.......................................................................... ... 80
.......................................................................... ... 81
.......................................................................... ... 82
.......................................................................... ... 83
.......................................................................... ... 84
Terminals and Reference Value for BCM ............. ... 85
Terminals and Reference Value for IPDM E/R ..... ... 86
CONSULT-II Function (BCM) ............................... ... 86
CONSULT-II INSPECTION PROCEDURE ....... ... 86
CONSULT-II APPLICATION ITEM .................... ... 88
Trouble Diagnosis ................................................ ... 89
WORK FLOW ................................................... ... 89
Preliminary Check ............................................... ... 90
Symptom Chart ....................................................... 91
Door Switch Check .............................................. ... 92
Hood Switch Check ............................................. ... 94
Combination Meter (Security Indicator Lamp)
Check .................................................................. ... 95
Front Door Lock Assembly LH (Key Cylinder Switch)
Check .................................................................. ... 96
Vehicle Security Horn Alarm Check ..................... ... 98
Vehicle Security Headlamp Alarm Check ............ ... 98
Door Lock/Unlock Switch Check ............................ 98
AUTOMATIC BACK DOOR SYSTEM .................... ... 99
Component Parts and Harness Connector Location ... 99
System Description .............................................. .100
OPERATION DESCRIPTION ........................... .100
Schematic ............................................................ .105Wiring Diagram — B/CLOS — .............................
.106
Terminals and Reference Value for Back Door Con-
trol Unit ................................................................. . 111
Terminals and Reference Value for BCM ............. .112
Trouble Diagnosis Procedure ............................... .113
Self-Diagnosis Procedures .................................. .113
INPUT SIGNAL CHECK MODE ........................ .113
OPERATING CHECK MODE ............................ .113
Diagnosis Chart ................................................... .114
Back Door Power Supply and Ground Circuit
Inspection ............................................................. .115
Power Liftgate Switch System Inspection ............ .116
GLASS HATCH AJAR SWITCH CHECK .......... .117
Back Door Close (Close) Switch System Inspection .118
Back Door Close (Cancel) Switch System Inspec-
tion ....................................................................... .119
Pinch Strip System Inspection ............................. .121
Back Door Warning Chime System Inspection .... .122
Half-Latch Switch System Inspection ................... .122
Open Switch System Inspection .......................... .123
Close Switch System Inspection .......................... .124
Back Door Handle Switch System Inspection ...... .125
Cinch Latch Motor System Inspection ................. .126
DOOR ..................................................................... .128
Fitting Adjustment ................................................ .128
FRONT DOOR .................................................. .128
REAR DOOR .................................................... .128
STRIKER ADJUSTMENT ................................. .128
Removal and Installation ...................................... .129
FRONT DOOR .................................................. .129
REAR DOOR .................................................... .129
BACK DOOR .................................................... .130
FRONT DOOR LOCK ............................................. .131
Component Structure ........................................... .131
Removal and Installation ...................................... .131
REMOVAL ......................................................... .131
INSTALLATION ................................................. .133
Disassembly and Assembly ................................. .133
DOOR KEY CYLINDER ASSEMBLY ................ .133
REAR DOOR LOCK ............................................... .134
Component Structure ........................................... .134
Removal and Installation ...................................... .134
REMOVAL ......................................................... .134
INSTALLATION ................................................. .134
BACK DOOR LOCK ............................................... .135
Power Back Door Opener .................................... .135
REMOVAL ........................................................ .135
INSTALLATION ................................................ .135
Door Lock Assembly ............................................ .136
REMOVAL ........................................................ .136
INSTALLATION ................................................ .136
IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-
NATS) ..................................................................... .137
Component Parts and Harness Connector Location .137
System Description .............................................. .138
System Composition ............................................ .138
ECM Re-communicating Function ....................... .139
Wiring Diagram — NATS — ................................. .140
Terminals and Reference Value for BCM ............. .141
Page 806 of 3383
POWER DOOR LOCK SYSTEMBL-25
C
DE
F
G H
J
K L
M A
B
BL
Revision: November 2009 2006 QX56
Terminals and Reference Value for BCMEIS005ZB
Work FlowEIS005ZC
1. Check the symptom and customer's requests.
2. Understand the outline of system. Refer to BL-17, "
System Description" .
3. According to the trouble diagnosis chart, repair or replace the cause of the malfunction. Refer to BL-29,
"Trouble Diagnoses Symptom Chart" .
4. Does power door lock system operate normally? OK: GO TO 5, NG: GO TO 3.
5. Inspection End.
Te r m i n a l Wire
Color Item
Condition Voltage (V)
(Approx.)
12 R/L Front door switch RH Door open (ON) → Door close (OFF) 0 → Battery voltage
13 GR Rear door switch RH Door open (ON) → Door close (OFF) 0 → Battery voltage
22 W/V Bus When ignition switch is ON or power
window timer operates
30 Y/BR Glass hatch switch Glass hatch switched released
→ Glass
hatch switched closed Battery voltage
→ 0
37 B/R Key switch and key lock sole-
noid (insert) Key inserted in IGN key cylinder (ON)
→
Key removed from IGN key cylinder (OFF) Battery voltage
→ 0
39 L CAN-H ——
40 P CAN-L ——
43 R/B Back door latch (door ajar
switch) Door open (ON)
→ Door close (OFF) 0 → Battery voltage
47 SB Front door switch LH Door open (ON) → Door close (OFF) 0 → Battery voltage
48 R/Y Rear door switch LH Door open (ON) → Door close (OFF) 0 → Battery voltage
53 L/W Glass hatch lock actuator Glass hatch switched released
→ Glass
hatch switch pressed 0
→ Battery voltage for 300 msec.
57 Y/R Battery power supply —Battery voltage
59 G Front door lock assembly LH
(actuator) (unlock) Driver door lock knob
(locked → unlocked) 0
→ Battery voltage
65 V All door lock actuators (lock) Driver door lock knob (neutral → lock) 0 → Battery voltage
66 G/Y Front door lock actuator RH,
rear door lock actuators LH/RH
and back door lock actuator
(unlock) Door lock and unlock switch (locked
→
unlocked) 0
→ Battery voltage
67 B Ground ——
70 W/B Battery power supply —Battery voltage
PIIA2344E
Page 814 of 3383
POWER DOOR LOCK SYSTEMBL-33
C
DE
F
G H
J
K L
M A
B
BL
Revision: November 2009 2006 QX56
4. CHECK BACK DOOR SWITCH GROUND
Check continuity between back door latch connector terminal 8 and
ground.
OK or NG
OK >> Back door switch circuit is OK.
NG >> Repair or replace harness.
Key Switch (Insert) CheckEIS005ZH
1. CHECK KEY SWITCH INPUT SIGNAL
With CONSULT-II
Check key switch "KEY ON SW" in DATA MONITOR mode with CONSULT –II. Refer to BL-27, "
DATA MONI-
TOR" .
When key is inserted to ignition key cylinder:
When key is removed from ignition key cylinder:
Without CONSULT-II
Check voltage between BCM connector M18 terminal 37 and
ground.
OK or NG
OK >> Key switch (insert) circuit is OK.
NG >> GO TO 2. 8 - Ground
: Continuity should exist.
LIIA0828E
KEY ON SW : ON
KEY ON SW : OFF
LIIA0169E
ConnectorTe r m i n a l s
ConditionVoltage (V)
(+) ( –)
M18 37 Ground Key is inserted. Battery voltage
Key is removed. 0
LIIA0567E