turn signal INFINITI QX56 2008 Factory User Guide

ADP-50
< COMPONENT DIAGNOSIS >
LIFTING SWITCH (FRONT)
LIFTING SWITCH (FRONT)
DescriptionINFOID:0000000001735475
Lifting switch (front) is equipped to the power seat switch LH on the seat cushion side surface. The operation
signal is input to the driver seat control unit when the lifting switch (front) is operated.
Component Function CheckINFOID:0000000001735476
1. CHECK FUNCTION
1. Select “LIFT FR SW-UP”, “LIFT FR SW-DN” in “DATA MONITOR” mode with CONSULT-III.
2. Check lifting switch (front) signal under the following conditions.
Is the indication normal?
YES >> INSPECTION END
NO >> Perform diagnosis procedure. Refer to ADP-50, "
DiagnosisProcedure".
Diagnosis ProcedureINFOID:0000000001735477
1. CHECK LIFTING SWITCH SIGNAL
1. Turn ignition switch ON.
2. Check voltage between driver seat control unit harness connec- tor and ground.
Is the inspection result normal?
YES >> GO TO 5
NO >> GO TO 2
2. CHECK LIFTING SW ITCH (FRONT) CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect driver seat control unit and power seat switch LH.
3. Check continuity between driver seat control unit harness con- nector and power seat switch LH harness connector.
Monitor item ConditionStatus
LIFT FR SW-UP Lifting switch front (up) Operate
ON
Release OFF
LIFT FR SW-DN Lifting switch front (down) Operate
ON
Release OFF
Driver seat
control unit
connector Te r m i n a l s
ConditionVoltage (V)
(Approx.)
(+) (–)
B202 13
Ground Lifting
switch (front) Operate
(down) 0V
Release Battery
voltage
28 Operate (up) 0V
Release Battery
voltage
PIIA4583E
Driver seat control unit connector Te r m i n a lPower seat switch
LH connector Terminal Continuity
B202 13
B208 5
Ye s
28 6
LIIA1129E
Revision: March 2010 2008 QX56

ADP-52
< COMPONENT DIAGNOSIS >
LIFTING SWITCH (REAR)
LIFTING SWITCH (REAR)
DescriptionINFOID:0000000001735479
Lifting switch (rear) is equipped to the power seat switch LH on the seat cushion side surface. The operation
signal is inputted to the driver seat control unit when the lifting switch (rear) is operated.
Component Function CheckINFOID:0000000001735480
1. CHECK FUNCTION
1. Select “LIFT RR SW-UP”, “LIFT RR SW-DN” in “Data monitor” mode with CONSULT-III.
2. Check lifting switch (rear) signal under the following conditions.
Is the indication normal?
YES >> INSPECTION END
NO >> Perform diagnosis procedure. Refer to ADP-52, "
DiagnosisProcedure".
Diagnosis ProcedureINFOID:0000000001735481
1. CHECK LIFTING SWITCH (REAR) SIGNAL
1. Turn ignition switch ON.
2. Check voltage between driver seat control unit harness connec- tor and ground.
Is the inspection result normal?
YES >> GO TO 5
NO >> GO TO 2
2. CHECK LIFTING SW ITCH (REAR) CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect driver seat control unit and power seat switch LH.
3. Check continuity between driver seat control unit harness con- nector and power seat switch LH harness connector.
4. Check continuity between driver seat control unit harness con- nector and ground.
Monitor item ConditionStatus
LIFT RR SW-UP Lifting switch rear (up) Operate
ON
Release OFF
LIFT RR SW-DN Lifting switch rear (down) Operate
ON
Release OFF
Driver seat
control unit
connector Te r m i n a l s
ConditionVoltage (V)
(Approx.)
(+) (–)
B202 14
Ground Lifting
switch (rear) Operate (down) 0
Release Battery voltage
29 Operate (up) 0
Release Battery voltage
PIIA4586E
Driver seat control unit connector Te r m i n a lPower sear switch
LH connector Terminal Continuity
B202 14
B208 8
Ye s
29 2
LIIA1131E
Revision: March 2010 2008 QX56

ADP-54
< COMPONENT DIAGNOSIS >
TILT SWITCH
TILT SWITCH
DescriptionINFOID:0000000001754039
ADP steering switch is equipped to the steering column. The operation signal is input to the automatic drive
positioner control unit when the ADP steering switch is operated.
Component Function CheckINFOID:0000000001754040
1.CHECK FUNCTION
1. Select “TILT SW-UP”, “TILT SW-DN” in “Data monitor” mode with CONSULT-III.
2. Check tilt switch signal under the following conditions.
Is the indication normal?
YES >> INSPECTION END
NO >> Perform diagnosis procedure. Refer to ADP-54, "
DiagnosisProcedure".
Diagnosis ProcedureINFOID:0000000001754041
1. CHECK ADP STEERING SWITCH SIGNAL
1. Turn ignition switch OFF.
2. Check voltage between automatic drive positioner control unit connector and ground.
Is the inspection result normal?
YES >> GO TO 4
NO >> GO TO 2
2. CHECK ADP STEERING SWITCH HARNESS CONTINUITY
1. Disconnect automatic drive positioner control unit connector and ADP steering switch.
2. Check continuity between automat ic drive positioner control unit
connector M33 terminals 1, 17 and ADP steering switch connec-
tor M16 terminals 2, 3.
3. Check continuity between automatic drive positioner control unit connector M33 terminals 1, 17 and ground.
Monitor item ConditionStatus
TILT SW-UP Tilt switch (up) Operate
ON
Release OFF
TILT SW-DN Tilt switch (down) Operate
ON
Release OFF
ConnectorTe r m i n a l s
ConditionVoltage (V)
(Approx.)
(+) (-)
M33 1
Ground ADP steering switch ON (UP
operation)
0
Other than above 5
17 ADP steering switch ON
(DOWN operation)
0
Other than above 5
LIIA0491E
1 - 2: Continuity should exist.
17 - 3 : Continuity should exist.
LIIA1434E
Revision: March 2010 2008 QX56

ADP-56
< COMPONENT DIAGNOSIS >
PEDAL ADJUSTING SWITCH
PEDAL ADJUSTING SWITCH
DescriptionINFOID:0000000001735483
Pedal adjusting switch is on the instrument panel. The operation signal is input to the driver seat control unit
when the pedal adjusting switch is operated. The pedal adjus ting switch signal is sent to the automatic drive
positioner control unit via UART communication.
Component Function CheckINFOID:0000000001735484
1. CHECK FUNCTION
1. Select “PEDAL SW-FR”, “PEDAL SW-RR” in “Data monitor” mode with CONSULT-III.
2. Check pedal adjusting switch signal under the following conditions.
Is the indication normal?
YES >> INSPECTION END
NO >> Perform diagnosis procedure. Refer to ADP-56, "
DiagnosisProcedure".
Diagnosis ProcedureINFOID:0000000001735485
1. CHECK PEDAL ADJUSTING SWITCH SIGNAL
1. Turn ignition switch ON.
2. Check voltage between driver seat control unit harness connec- tor and ground.
Is the inspection result normal?
YES >> GO TO 5
NO >> GO TO 2
2. CHECK PEDAL ADJUSTING SWITCH CIRCUIT
Monitor item ConditionStatus
PEDAL SW-FR Pedal adjusting switch (forward) Operate
ON
Release OFF
PEDAL SW-RR Pedal adjusting switch (backward) Operate
ON
Release OFF
Driver seat
control unit connector Te r m i n a l s
ConditionVoltage (V)
(Approx.)
(+) (–)
B202 15
Ground Pedal ad-
justing switch Operate
(backward) 0
Release Battery
voltage
30 Operate
(forward) 0
Release Battery
voltage
PIIA4591E
Revision: March 2010 2008 QX56

SEAT MEMORY SWITCHADP-59
< COMPONENT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
SEAT MEMORY SWITCH
DescriptionINFOID:0000000001735487
Memory switch is equipped on the seat memory switch installed to the front door LH trim. The operation signal
is input to the automatic drive positioner control unit when the memory switch is operated.
Component Function CheckINFOID:0000000001735488
1. CHECK FUNCTION
1. Select “MEMORY SW 1”, “MEMORY SW 2”, "SET SW" in “Data monitor” mode with CONSULT-III.
2. Check seat memory switch signal under the following conditions.
Is the indication normal?
YES >> INSPECTION END
NO >> Perform diagnosis procedure. Refer to ADP-59, "
DiagnosisProcedure".
Diagnosis ProcedureINFOID:0000000001735489
1. CHECK MEMORY SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect automatic drive positioner control unit and seat memory switch.
3. Check continuity between automat ic drive positioner control unit
harness connector and seat memo ry switch harness connector.
4. Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES >> GO TO 2
NO >> Repair or replace harness.
2. CHECK MEMORY SWITCH GROUND CIRCUIT
Monitor item ConditionStatus
MEMORY SW1 Memory switch 1 Push
ON
Release OFF
MEMORY SW2 Memory switch 2 Push
ON
Release OFF
SET SW Set switch Push
ON
Release OFF
Automatic drive
positioner control unit connector Te r m i n a l
Seat memory
switch connector Terminal Continuity
M33 9
D5 1
Ye s
24 3
25 2
Automatic drive positioner control unit connector Te r m i n a l
GroundContinuity
M33 9
No
24
25
PIIA4576E
Revision: March 2010 2008 QX56

DOOR MIRROR REMOTE CONTROL SWITCHADP-61
< COMPONENT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
DOOR MIRROR REMOTE CONTROL SWITCH
CHANGEOVER SWITCH
CHANGEOVER SWITCH : DescriptionINFOID:0000000001735491
Changeover switch is integrated into door mirror remote control switch.
Changeover switch has three positions (L, N and R).
It changes door mirror motor operation by transmitting control signal to automatic drive positioner control unit.
CHANGEOVER SWITCH : Comp onent Function CheckINFOID:0000000001735492
1. CHECK CHANGEOVER SWITCH FUNCTION
Check the operation on “MIR CHNG SW-R” or “MIR CHNG SW-L” in “DATA MONITOR” mode with CON-
SULT-III.
Refer to ADP-26, "
CONSULT-III Function".
Is the inspection result normal?
YES >> Changeover switch function is OK.
NO >> Refer to ADP-61, "
CHANGEOVER SWITCH : Diagnosis Procedure".
CHANGEOVER SWITCH : Diagnosis ProcedureINFOID:0000000001735493
1. CHECK CHANGEOVER SWITCH SIGNAL
1. Turn ignition switch ON.
2. Check voltage between automatic drive positioner control unit
connector and ground.
Is the inspection result normal?
YES >> GO TO 6
NO >> GO TO 2
2. CHECK HARNESS CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect automatic drive positioner control unit and door mir- ror remote control switch.
3. Check continuity between automat ic drive positioner control unit
connector and door mirror remote control switch connector.
4. Check continuity between automatic driv e positioner control unit connector and ground.
Te r m i n a l s
Change over switch condition Voltage (V)
(Approx.)
(+)
(-)
Automatic drive
positioner control unit connector Terminal
M33 2
Ground RIGHT
0
Other than above 5
18 LEFT
0
Other than above 5
PIIA4767E
Automatic drive
positioner control unit connector Te r m i n a lDoor mirror re-
mote control
switch connector Terminal Continuity
M33 (A) 2
D10 (B) 11
Ye s
18 10
ALJIA0201ZZ
Revision: March 2010 2008 QX56

ADP-62
< COMPONENT DIAGNOSIS >
DOOR MIRROR REMOTE CONTROL SWITCH
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3. CHECK DOOR MIRROR REMOTE CONTROL SWITCH GROUND CIRCUIT
Check continuity between door mirro r remote control switch connec-
tor and ground.
Is the inspection result normal?
YES >> GO TO 4
NO >> Repair or replace harness.
4. CHECK AUTOMATIC DRIVE POSITIONER CONTROL UNIT OUTPUT SIGNAL
1. Connect automatic drive positioner control unit.
2. Turn ignition switch ON.
3. Check voltage between automatic drive positioner control unit connector and ground.
Is the inspection result normal?
YES >> GO TO 5.
NO >> Replace automatic drive positioner control unit.
5. CHECK CHANGEOVER SWITCH
Check changeover switch.
Refer to ADP-62, "
CHANGEOVER SWITCH : Component Inspection".
Is the inspection result normal?
YES >> Refer to GI-38, "Intermittent Incident".
NO >> Replace door mirror remote control switch.
6. CHECK INTERMITTENT INCIDENT
Check intermittent incident.
Refer to GI-38, "
Intermittent Incident".
Is the inspection result normal?
YES >> Replace automatic drive positioner control unit.
NO >> Repair or replace the malfunctioning parts.
CHANGEOVER SWITCH : Component InspectionINFOID:0000000001735494
1. CHECK CHANGEOVER SWITCH
Automatic drive positioner control
unit connector Te r m i n a l
GroundContinuity
M33 (A) 2
No
18
Door mirror remote control switch
connector Terminal
GroundContinuity
D10 7 Yes
ALJIA0189ZZ
Te r m i n a l s
Voltage (V)(Approx.)
(+)
(-)
Automatic drive positioner
control unit connector Te r m i n a l
M33 2
Ground 5
18
PIIA4767E
Revision: March 2010 2008 QX56

ADP-64
< COMPONENT DIAGNOSIS >
DOOR MIRROR REMOTE CONTROL SWITCH
1. Turn ignition switch OFF.
2. Disconnect automatic drive posit ioner control unit and door mir-
ror remote control switch.
3. Check continuity between automat ic drive positioner control unit
connector and door mirror remote control switch connector.
4. Check continuity between automatic driv e positioner control unit connector and ground.
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3. CHECK DOOR MIRROR REMOTE CONTROL SWITCH GROUND CIRCUIT
Check continuity between door mirro r remote control switch connec-
tor and ground.
Is the inspection result normal?
YES >> GO TO 4
NO >> Repair or replace harness.
4. CHECK AUTOMATIC DRIVE POSITIONER CONTROL UNIT OUTPUT SIGNAL
1. Connect automatic drive positioner control unit.
2. Turn ignition switch ON.
3. Check voltage between automatic drive positioner control unit and ground.
Is the inspection result normal?
Automatic drive
positioner control unit connector Te r m i n a lDoor mirror remote
control switch con- nector Terminal Continuity
M33 (A) 3
D10 (B) 15
Ye s
41
3
19 12
20 4
Automatic drive positioner control unit connector Te r m i n a l
GroundContinuity
M33 (A) 3
No
4
19
20
ALJIA0191ZZ
Door mirror remote control switch connector Te r m i n a l
Ground Continuity
D10 7 Yes
ALJIA0189ZZ
Te r m i n a l s
Voltage (V)(Approx.)
(+)
(-)
Automatic drive positioner
control unit connector Te r m i n a l
M33 3
Ground 5
4
19
20
PIIA4771E
Revision: March 2010 2008 QX56

DETENTION SWITCHADP-67
< COMPONENT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
DETENTION SWITCH
DescriptionINFOID:0000000001735500
Park position switch is installed on A/T shift selector. It is turned OFF when the A/T selector lever is in P posi-
tion. The driver seat control unit judges that the A/T selector lever is in P position if cont\
inuity does not exist in
this circuit.
Component Function CheckINFOID:0000000001735501
1. CHECK FUNCTION
1. Select “DETENT SW” signal in “Data monitor” mode with CONSULT-III.
2. Check park position switch signal under the following conditions.
Is the indication normal?
YES >> INSPECTION END
NO >> Perform diagnosis procedure. Refer to ADP-67, "
DiagnosisProcedure".
Diagnosis ProcedureINFOID:0000000001735502
1. CHECK DTC WITH “BCM”
Check “Self Diagnostic Result” for BCM with CONSULT-lll.
Is any other DTC detected?
YES >> Check the DTC.
NO >> GO TO 2
2. CHECK PARK POSITION SWITCH INPUT SIGNAL
1. Turn ignition switch ON.
2. Mechanical key must be removed from the key switch.
3. Check voltage between driver seat control unit harness connec- tor and ground.
Is the inspection result normal?
YES >> GO TO 4
NO >> GO TO 3
3. CHECK PARK POSITION SWITCH CIRCUIT
Monitor item ConditionStatus
DETENT SW A/T selector lever P position
OFF
Other than
above ON
Driver seat
control unit connector Te r m i n a l
ConditionVoltage (V)
(Approx.)
(+) (-)
B202 21 Ground A/T selec-
tor leverP position
Battery volt-
age
Other than
above 0V
ALJIA0193ZZ
Revision: March 2010
2008 QX56

SLIDING SENSORADP-71
< COMPONENT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
SLIDING SENSOR
DescriptionINFOID:0000000001735507
• The sliding sensor is installed to the seat slide cushion frame.
• The pulse signal is input to the driver seat control unit when sliding is performed.
• The driver seat control unit counts the pulse and calculates the sliding amount of the seat.
Component Function CheckINFOID:0000000001735508
1. CHECK FUNCTION
1. Select “SLIDE PULSE” in “Data monitor” mode with CONSULT-III.
2. Check sliding sensor signal under the following conditions.
Is the indication normal?
YES >> INSPECTION END
NO >> Perform diagnosis procedure. Refer to ADP-71, "
DiagnosisProcedure".
Diagnosis ProcedureINFOID:0000000001735509
1. CHECK SLIDING SENSOR SIGNAL
1. Turn ignition switch ON.
2. Read voltage signal between driver seat control unit harness connector and ground with osiloscope.
Is the inspection result normal?
YES >> GO TO 4
NO >> GO TO 2
2. CHECK SLIDING SENSOR CIRCUITS
Monitor item Condition Valve
SLIDE PULSE Seat slidingOperate (forward)
Change (increase)
Operate (backward) Change (decrease)
Release No change
Te r m i n a l s
ConditionVoltage signal
(+)
(–)
Driver’s
seat
control unit Te r m i -
nal
B202 24 Ground Seat
slidingOperate
Other
than
above
0 or 5
PIIA4556E
PIIA3277E
Revision: March 2010
2008 QX56