turn signal INFINITI QX56 2010 Factory Owners Manual

BCS-22
< FUNCTION DIAGNOSIS >[BCM]
DIAGNOSIS SYSTEM (BCM)
HEADLAMP : CONSULT-III Function (BCM - HEAD LAMP)
INFOID:0000000005146401
WORK SUPPORT
*: Initial setting
DATA MONITOR
ACTIVE TEST
Work Item Setting item Setting
BATTERY SAVER SET ON* With the exterior lamp battery saver function
OFF Without the exterior lamp battery saver function
CUSTOM A/LIGHT SET-
TING MODE1* Normal
MODE2 More sensitive setting than normal setting (Turns ON earlier than normal operation.)
MODE3 More sensitive setting than MODE 2 (Turns ON earlier than MODE 2.)
MODE4 Less sensitive setting than normal setting (Turns ON later than normal operation.)
ILL DELAY SET MODE1* 45 sec.
Sets delay timer function timer operation time
(All doors closed)
MODE2
Without the func-
tion
MODE3 30 sec.
MODE4 60 sec.
MODE5 90 sec.
MODE6 120 sec.
MODE7 150 sec.
MODE8 180 sec.
Monitor Item [Unit] Description
IGN ON SW [ON/OFF] Ignition switch (ON) status judged from IGN signal (ignition power supply)
ACC ON SW [ON/OFF] Ignition switch (ACC) status judged from ACC signal (accessory power supply)
HI BEAM SW [ON/OFF]
Each switch status that BCM judges from the combination switch reading function
HEAD LAMP SW 1 [ON/OFF]
HEAD LAMP SW 2 [ON/OFF]
LIGHT SW 1ST [ON/OFF]
AUTO LIGHT SW [ON/OFF]
PASSING SW [ON/OFF]
FR FOG SW [ON/OFF]
TURN SIGNAL R [ON/OFF]
TURN SIGNAL L [ON/OFF]
DOOR SW-DR [ON/OFF]
The switch status input from front door switch LH
DOOR SW-AS [ON/OFF] The switch status input from front door switch RH
DOOR SW-RR [ON/OFF] The switch status input from rear door switch RH
DOOR SW-RL [ON/OFF] The switch status input from rear door switch LH
BACK DOOR SW [ON/OFF] The switch status input from back door switch
CARGO LAMP SW [ON/OFF] Cargo lamp status that BCM judges from the vehicle condition
OPTICAL SENSOR [ON/OFF] The value of exterior brightness voltage input from the optical sensor
Revision: April 20092010 QX56

BCS
DIAGNOSIS SYSTEM (BCM)BCS-23
< FUNCTION DIAGNOSIS > [BCM]
C
D
E
F
G H
I
J
K L
B A
O P
N
WIPER
WIPER : CONSULT-III Function (BCM - WIPER)INFOID:0000000005146402
WORK SUPPORT
*: Factory setting
DATA MONITOR
Test Item
Operation Description
TAIL LAMP ON
Transmits the position light request signal to IPDM E/R with CAN com-
munication to turn the tail lamp ON.
OFF Stops the tail lamp request signal transmission.
HEAD LAMP HI
Transmits the high beam request signal with CAN communication to turn
the headlamp (HI).
LO Transmits the low beam request signal with CAN communication to turn
the headlamp (LO).
OFF Stops the high & low beam request signal transmission.
FR FOG LAMP ON
Transmits the front fog lights request signal to IPDM E/R with CAN com-
munication to turn the front fog lamp ON.
OFF Stops the front fog lights request signal transmission.
CARGO LAMP ON
Transmits the cargo lamp request signal with CAN communication to
turn the lamp ON.
OFF Stops the cargo lamp request signal transmission.
CORNERING LAMP LH
Transmits the LH cornering lamp request signal with CAN communica-
tion to turn the lamp ON.
RH Transmits the RH cornering lamp request signal with CAN communica-
tion to turn the lamp ON.
OFF Stops the day time running light request signal transmission.
Work Item Setting
Item Description
WIPER SPEED
SETTING ON*
With vehicle speed
(Front wiper intermittent time linked with the vehicle speed and wiper intermittent dial position)
OFF Without vehicle speed
(Front wiper intermittent time linked with the wiper intermittent dial position)
Monitor Item
[Unit] Description
IGN ON SW [ON/OFF] Ignition switch ON status judged from ignition power supply
IGN SW CAN [ON/OFF] Ignition switch ON status received from IPDM E/R via CAN communication
FR WIPER HI [ON/OFF]
Each switch status that BCM judges from the combination switch reading function
FR WIPER LOW [ON/OFF]
FR WIPER INT [ON/OFF]
FR WASHER SW [ON/OFF]
INT VOLUME [1 - 7]
Each switch status that BCM judges from the combination switch reading function
FR WIPER STOP [ON/OFF] Front wiper motor (stop position) status received from IPDM E/R with CAN communica-
tion
VEHICLE SPEED [km/h] The value of the vehicle speed signal received from combination meter with CAN com-
munication
Revision: April 20092010 QX56

BCS-24
< FUNCTION DIAGNOSIS >[BCM]
DIAGNOSIS SYSTEM (BCM)
ACTIVE TEST
FLASHER
FLASHER : CONSULT-III Function (BCM - FLASHER)INFOID:0000000005146403
DATA MONITOR
ACTIVE TEST
AIR CONDITIONER
AIR CONDITIONER : CONSULT-III Function (BCM - AIR CONDITIONER)INFOID:0000000005146404
DATA MONITOR
RR WIPER ON [ON/OFF]
Each switch status that BCM judges from the combination switch reading function
RR WIPER INT [ON/OFF]
RR WASHER SW [ON/OFF]
RR WIPER STOP [ON/OFF] Rear wiper motor (stop position) status input from the rear wiper motor Monitor Item
[Unit] Description
Test Item Operation
Description
FR WIPER HI
Transmits the front wiper request signal (HI) to IPDM E/R with CAN communication to op-
erate the front wiper HI operation.
LO Transmits the front wiper request signal (LO) to IPDM E/R with CAN communication to
operate the front wiper LO operation.
INT Transmits the front wiper request signal (INT) to IPDM E/R with CAN communication to
operate the front wiper INT operation.
OFF Stops transmitting the front wiper request signal to stop the front wiper operation.
RISE UP WIPER
TEST ON Outputs the voltage to operate the rear wiper motor.
OFF Stops the voltage to stop.
Monitor Item [Unit] Description
IGN ON SW [ON/OFF] Ignition switch (ON) status judged from IGN signal (ignition power supply)
HAZARD SW [ON/OFF] The switch status input from the hazard switch
TURN SIGNAL R [ON/OFF] Each switch condition that BCM judges from the combination switch reading function
TURN SIGNAL L [ON/OFF]
BRAKE SW [ON/OFF] The switch status input from the brake switch
Test ItemOperation Description
FLASHER RH Outputs the voltage to turn the right side turn signal lamps ON.
LH Outputs the voltage to turn the left side turn signal lamps ON.
OFF Stops the voltage to turn the turn signal lamps OFF.
Monitor Item [Unit] Contents
IGN ON SW [ON/OFF] Display [ignition switch position (On)/(Off), ACC position (Off)] status as judged from ignition
switch signal
FAN ON SIG [ON/OFF] Display [FAN (On)/FAN (Off)] st atus as judged form blower fan motor switch signal
AIR COND SW [ON/OFF] Display [COMP (On)/COMP (Off)] status as judged form air conditioner switch signal
Revision: April 20092010 QX56

BCS
DIAGNOSIS SYSTEM (BCM)BCS-25
< FUNCTION DIAGNOSIS > [BCM]
C
D
E
F
G H
I
J
K L
B A
O P
N
INTELLIGENT KEY
INTELLIGENT KEY : CONSULT-III Fu
nction (BCM - INTELLIGENT KEY)INFOID:0000000005146405
DATA MONITOR
COMB SW
COMB SW : CONSULT-III Function (BCM - COMB SW)INFOID:0000000005146406
DATA MONITOR
Monitor Item
[Unit] Condition
I-KEY LOCK [ON/OFF] Indicates condition of lock signal from Intelligent Key
I-KEY UNLOCK [ON/OFF] Indicates [condition of unlock signal from Intelligent Key
I-KEY TRUNK [ON/OFF] Indicates condition of trunk open signal fr om Intelligent Key
I-KEY PW DWN [ON/OFF] Indicates condition of all power window signal from Intelligent Key
I-KEY PANIC [ON/OFF] Indicates condition of panic signal from Intelligent Key
PUSH SW [ON/OFF] Indicates condition of ignition knob switch
Monitor Item
[Unit] Description
TURN SIGNAL R
[OFF/ON] Displays the status of the TURN RH switch in combination switch judged by BCM with the combination switch
reading function
TURN SIGNAL L
[OFF/ON] Displays the status
of the TURN LH switch in co mbination switch judged by BCM with the combination switch
reading function
HI BEAM SW
[OFF/ON] Displays the status of the HI BEAM sw
itch in combination switch judged by BCM with the combination switch
reading function
HEAD LAMP SW1
[OFF/ON] Displays the status of the HEADLAMP switch in combination switch judged by BCM with the combination
switch reading function
HEAD LAMP SW2
[OFF/ON] Displays the status of the HEADLAMP switch in combination switch judged by BCM with the combination
switch reading function
LIGHT SW 1ST
[OFF/ON] Displays the status of the HEADLAMP switch in combination switch judged by BCM with the combination
switch reading function
PA S S I N G S W
[OFF/ON] Displays the status of the PASSING sw
itch in combination switch judged by BCM with the combination switch
reading function
AUTO LIGHT SW
[OFF/ON] Displays the status of the AUTO LIGHT switch in combination switch judged by BCM with the combination
switch reading function
FR FOG SW
[OFF/ON] Displays the status of the FR FOG switch in combination switch judged by BCM with the combination switch
reading function
FR WIPER HI
[OFF/ON] Displays the status of the FR WIPER HI switch in combination switch judged by BCM with the combination
switch reading function
FR WIPER LOW
[OFF/ON] Displays the status of the FR WIPER LOW switch in combination switch judged by BCM with the combination
switch reading function
FR WIPER INT
[OFF/ON] Displays the status of the FR WIPER INT switch in combination switch judged by BCM with the combination
switch reading function
FR WASHER SW
[OFF/ON] Displays the status of the FR WASHER switch in combination switch judged by BCM with the combination
switch reading function
INT VOLUME
[1 - 7] Displays the status of wiper intermittent dial position judged by BCM with the combination switch reading
function
RR WIPER ON
[OFF/ON] Displays the status of the RR WIPER switch in combination switch judged by BCM with the combination
switch reading function
Revision: April 20092010 QX56

BCS
DIAGNOSIS SYSTEM (BCM)BCS-27
< FUNCTION DIAGNOSIS > [BCM]
C
D
E
F
G H
I
J
K L
B A
O P
N
*: Each lamp switch is in ON position.
TRUNK
TRUNK : CONSULT-III Function (BCM - TRUNK)INFOID:0000000005146409
DATA MONITOR
ACTIVE TEST
RETAINED PWR
RETAINED PWR : CONSULT-III Function (BCM - RETAINED PWR)INFOID:0000000005369877
DATA MONITOR
ACTIVE TEST
WORK SUPPORT
SIGNAL BUFFER
Test Item
Operation Description
BATTERY SAVER OFF Cuts the interior room lamp power supply to turn interior room lamps OFF.
ON Outputs the interior room lamp power supply to turn interior room lamps ON.*
Monitor Item [Unit] Contents
IGN ON SW [ON/OFF] Indicates condition of ignition switch in ON position
I-KEY TRUNK [ON/OFF] Indicates condition of Intellig ent Key back door opening operation
TRUNK OPNR SW [ON/OFF] Indicates condit ion of back door opener switch.
VEHICLE SPEED [ON/OFF] Indicates condition of vehicle speed signal from combination meter
Test Item Description
TRUNK/BACK DOOR This test is able to check back door open operation.
Back door open when “OPEN” on CONSULT-III screen is touched.
Monitor Item
[Unit] Description
IGN ON SW [ON/OFF] Indicates condition of ignition switch.
DOOR SW-DR [ON/OFF] Indicates condition of front door switch LH.
DOOR SW-AS [ON/OFF] Indicates condition of front door switch RH.
Test Item Description
RETAINED PWR This test is able to supply RAP signal (powe
r) from BCM (body control module) to power window
system and power sunroof system (if equipped). Those systems can be operated when turning on
“RETAINED PWR” on CONSULT-III screen even if the ignition switch is turned OFF.
NOTE:
During this test, CONSULT-III can be operated with ignition switch in OFF position. “RETAINED
PWR” should be turned “ON” or “OFF” on CONSULT-III screen when ignition switch is ON. Then
turn ignition switch OFF to check retained power operation. CONSULT-III might be stuck if “RE-
TAINED PWR” is turned “ON” or “OFF” on CONSULT-III screen when ignition switch is OFF.
Work item Description
RETAINED PWR SET RAP signal’s power supply period can be changed by mode setting. Selects RAP signal’s power
supply period between three steps
• MODE1 (45 sec.)/MODE2 (OFF)/MODE 3 (2 min.).
Revision: April 20092010 QX56

BCS
DIAGNOSIS SYSTEM (BCM)BCS-29
< FUNCTION DIAGNOSIS > [BCM]
C
D
E
F
G H
I
J
K L
B A
O P
N
ERASE SELF-DIAGNOSIS
With CONSULT-III
1. Perform applicable inspection of malfuncti
oning item and then repair or replace.
2. Turn ignition switch “ON” and select “SELF-DIAG RESULTS” mode for “AIR PRESSURE MONITOR” with
CONSULTIII.
3. Touch “ERASE” on CONSULT-III screen to erase memory.
Without CONSULT-III
• In order to make it easier to find the cause of hard-to-duplicate malfunctions, malfunction information is
stored into the control unit as necessary during use by the user. This memory is not erased no matter how
many times the ignition switch is turned “ON” and “OFF”.
• However, this information is erased by turning ignition switch “OFF” after performing self-diagnostic or by
erasing the memory using the CONSULT-III.
21 Transmitter no data (Front LH) Data from front LH transmitter can not be received.
WT-34
22 Transmitter no data (Front RH) Data from front RH transmitter can not be received.
23 Transmitter no data (Rear RH) Data from Rear RH transmitter can not be received.
24 Transmitter no data (Rear LH) Data from Rear LH transmitter can not be received.
31Transmitter ch
ecksum error
(Front LH) Checksum data from front LH transmitter is malfunctioning.
WT-34
32Transmitter ch
ecksum error
(Front RH) Checksum data from front RH transmitter is malfunctioning.
33 Transmitter ch
ecksum error
(Rear RH) Checksum data from rear RH transmitter is malfunctioning.
34 Transmitter ch
ecksum error
(Rear LH) Checksum data from rear RH transmitter is malfunctioning.
35 Transmitter pressu
re data error
(Front LH) Air pressure data from front LH transmitter is malfunction.
WT-34
36Transmitter pressu
re data error
(Front RH) Air pressure data from front RH transmitter is malfunction.
37 Transmitter pressu
re data error
(Rear RH) Air pressure data from rear RH transmitter is malfunction.
38 Transmitter pressu
re data error
(Rear LH) Air pressure data from rear LH transmitter is malfunction.
41 Transmitter function code error
(Front LH) Function code data from front LH transmitter is malfunction.
WT-34
42Transmitter function code error
(Front RH)
Function code data from front RH transmitter is malfunction.
43 Transmitter function code error
(Rear RH) Function code data from rear RH transmitter is malfunction.
44 Transmitter function code error
(Rear LH) Function code data from rear LH transmitter is malfunction.
45 Transmitter battery voltage low
(Front LH)
Battery voltage of front LH transmitter drops.
WT-34
46Transmitter battery voltage low
(Front RH) Battery voltage of front RH transmitter drops.
47 Transmitter battery voltage low
(Rear RH) Battery voltage of rear RH transmitter drops.
48 Transmitter battery voltage low
(Rear LH) Battery voltage of rear LH transmitter drops.
52 Vehicle speed signal error Speed signal is not detected. WT-34
No flicker-
ing Tire pressure warning check
switch
Tire pressure warning sw
itch circuit is open. –
Flickering
pattern Items
Diagnostic items detected when··· Check item
Revision: April 20092010 QX56

BCS-30
< FUNCTION DIAGNOSIS >[BCM]
DIAGNOSIS SYSTEM (BCM)
AIR PRESSURE MONITOR : CONSULT-III Function
INFOID:0000000005146413
WORK SUPPORT
ID Read
The registered ID number is displayed.
ID Regist
Refer to WT-6, "ID Registration Procedure".
SELF-DIAG RESULTS
Operation Procedure
Refer to WT-11, "CONSULT-III Function (BCM)".
DATA MONITOR
Screen of data monitor mode is displayed. Refer to WT-11, "CONSULT-III Function (BCM)".
NOTE:
When malfunction is detected, CONSUL T-III perform REAL-TIME DIAGNOSIS.
Also, any malfunction detected while in this mode will be displayed at real time.
ACTIVE TEST
NOTE:
Before performing the self-diagnosis, be sure to register the ID, or else the actual malfunction may be different
from that displayed on CONSULT-III.
TEST ITEM LIST
THEFT ALM
THEFT ALM : CONSULT-III F unction (BCM - THEFT ALM)INFOID:0000000005370264
WORK SUPPORT
DATA MONITOR
Test item Content
WARNING LAMP This test is able to check to make sure that the warning lamp turns on.
ID REGIST WARNING This test is able to check to make su re that the buzzer sounds or the warning lamp turns on.
FLAT TIRE WARNING This test is able to check to make sure that the buzzer sounds.
HORN This test is able to check to make sure that the horn sounds.
FLASHER This test is able to check to make sure that each turn signal lamp turns on.
Test Item Description
SECURITY ALARM SET This mo de is able to confirm and change security alarm ON-OFF setting.
THEFT ALM TRG The switch which triggered vehicle security alarm is recorded. This mode is able to confirm and
erase the record of vehicle security alarm. The trigger data can be erased by touching “CLEAR” on
CONSULT-III screen.
Monitor Item
[Unit] Description
IGN ON SW [ON/OFF] Indicates ignition switch (ON) status judged from IGN signal (ignition power supply)
ACC ON SW [ON/OFF] Indicates ignition switch (ACC) status judged from ACC signal (accessory power supply)
I-KEY LOCK [ON/OFF] Indicates lock signal status received from Intelligent Key unit by CAN communication
I-KEY UNLOCK [ON/OFF] Indicates unlock si gnal status received from Intelligent Key unit by CAN communication
I-KEY TRUNK [ON/OFF] Indicates condit ion of back door opener switch
TRNK OPNR SW [ON/OFF] Indicates switch status of back door opener switch
TRNK OPN MNTR [ON/OFF] Indicates switch status of back door latch
Revision: April 20092010 QX56

BCS-32
< COMPONENT DIAGNOSIS >[BCM]
U1000 CAN COMM CIRCUIT
COMPONENT DIAGNOSIS
U1000 CAN COMM CIRCUIT
DescriptionINFOID:0000000005146415
Refer to
LAN-44, "CAN Communication Signal Chart".
DTC LogicINFOID:0000000005146416
DTC DETECTION LOGIC
Diagnosis ProcedureINFOID:0000000005146417
1. PERFORM SELF DIAGNOSTIC
1. Turn ignition switch ON and wait for 2 seconds or more.
2. Check “Self Diagnostic Result” of BCM.
Is
“CAN COMM CIRCUIT” displayed?
YES >> Refer to LAN-14, "Trouble Diagnosis Flow Chart".
NO >> Refer to GI-38, "
Intermittent Incident".
DTCCONSULT-III display
description DTC Detection Condition
Possible cause
U1000 CAN COMM CIRCUIT When BCM cannot communicate CAN com-
munication signal continuously for 2 sec-
onds or more. Any item (or items) of the following listed below is
malfunctioning in CAN communication system.
•Transmission
• Receiving (ECM)
• Receiving (METER/M&A)
• Receiving (TCM)
• Receiving (MULTI AV)
• Receiving (IPDM E/R)
• Receiving (I-KEY)
Revision: April 20092010 QX56

BCS
POWER SUPPLY AND GROUND CIRCUITBCS-33
< COMPONENT DIAGNOSIS > [BCM]
C
D
E
F
G H
I
J
K L
B A
O P
N
POWER SUPPLY AND GROUND CIRCUIT
Diagnosis ProcedureINFOID:0000000005146421
Regarding Wiring Diagram information, refer to
BCS-49, "Wiring Diagram".
1. CHECK FUSES AND FUSIBLE LINK
Check that the following fuses and fusible link are not blown.
Is the fuse blown?
YES >> Replace the blown fuse or fusible link after repairing the affected circuit.
NO >> GO TO 2
2. CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM.
3. Check voltage between BCM harness connector and ground.
Is the measurement value normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3. CHECK GROUND CIRCUIT
Terminal No. Signal nameFuses and fusible link No.
57 Battery power supply 22 (15A)
70 F (50A)
11 Ignition ACC or ON 4 (10A)
38 Ignition ON or START 59 (10A)
ConnectorTe r m i n a l s
Power
source Condition Voltage (V) (Ap-
prox.)
(+) (-)
M18 11 Ground
ACC
power
supply Ignition
switch
ACC or
ON Battery voltage
38 Ground Ignition
power
supply Ignition
switch ON or START Battery voltage
M20 57 Ground
Battery
power
supply Ignition
switch OFF Battery voltage
70 Ground Battery
power
supply Ignition
switch
OFF Battery voltage
LIIA2415E
Revision: April 20092010 QX56

BCS-38
< COMPONENT DIAGNOSIS >[BCM]
COMBINATION SWITCH
COMBINATION SWITCH
DescriptionINFOID:0000000005146426
COMBINATION SWITCH MATRIX
Combination switch consists of INPUT circuit and OUTPUT circuit.
Combination switch circuit
Combination switch INPUT-OUTPUT system list
NOTE:
Headlamp has a dual system switch.
Diagnosis ProcedureINFOID:0000000005146427
1. CHECK LIGHT & TURN SIGNAL SWITCH
Check operation with normal light and turn signal switch installed.
Does it operate normally?
YES >> Replace light and turn signal switch. Refer to EXL-154, "Removal and Installation".
NO >> GO TO 2
2. CHECK WIPER & WASHER SWITCH
Check operation with normal wiper and washer switch installed.
Does it operate normally?
YES >> Replace wiper and washer switch. Refer to WW-85, "Wiper and Washer Switch".
SystemOUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 OUTPUT 5
INPUT 1 —FR WASHER FR WIPER LOW TURN LH TURN RH
INPUT 2 FR WIPER HI —FR WIPER INT PASSING HEADLAMP 1
INPUT 3 INT VOLUME 1 RR WASHER —HEADLAMP 2 HI BEAM
INPUT 4 RR WIPER INT INT VOLUME 3 AUTO LIGHT —TAIL LAMP
INPUT 5 INT VOLUME 2 RR WIPER —FR FOG —
LIIA0760E
Revision: April 20092010 QX56