display INFINITI QX56 2011 Factory Service Manual

DIAGNOSIS SYSTEM (TCM)TM-63
< SYSTEM DESCRIPTION > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
FR/B SOL MON (A) — — Monitors the command current from TCM to the
front brake solenoid, and displays the monitor
value.
HLR/C SOL MON (A) — — Monitors the command current from TCM to the
high and low reverse clutch solenoid, and dis-
plays the monitor value.
I/C SOL MON (A) — — Monitors the command current from TCM to the
input clutch solenoid, and displays the monitor
value.
D/C SOL MON (A) — — Monitors the command current from TCM to the
direct clutch solenoid, and displays the monitor
value.
2346/B SOL MON (A) — — Monitors the command current from TCM to the
2346 brake solenoid, and displays the monitor
value.
GEAR RATIO — X Displays the gear ratio calculated from input
speed and output speed.
ENGINE TORQUE (Nm) — — Displays the engine torque estimated value re-
ceived via CAN communication.
ENG TORQUE D (Nm) — — Displays the engine torque estimated value re-
flected the requested torque of each control unit
received via CAN communication.
INPUT TRQ S (Nm) — — Displays the input torque using for the oil pres-
sure calculation process of shift change control.
INPUT TRQ L/P (Nm) — — Displays the input torque using for the oil pres-
sure calculation process of line pressure con-
trol.
TRGT PRES L/P (kPa, kg/cm
2 or psi)—— Displays the target oil pressure value of torque
converter clutch solenoid valve calculated by
the oil pressure calculation process of lock-up
control.
TRGT PRES TCC (kPa, kg/cm
2 or psi)—— Displays the target oil pressure value of torque
converter clutch solenoid valve calculated by
the oil pressure calculation process of shift
change control.
TRGT PRES L/B (kPa, kg/cm
2 or psi)—— Displays the target oil pressure value of low
brake solenoid valve calculated by the oil pres-
sure calculation process of shift change control.
TRGT PRE FR/B (kPa, kg/cm
2 or psi)—— Displays the target oil pressure value of front
brake solenoid valve calculated by the oil pres-
sure calculation process of shift change control.
TRG PRE HLR/C (kPa, kg/cm
2 or psi)—— Displays the target oil pressure value of high
and low reverse clutch solenoid valve calculat-
ed by the oil pressure calculation process of
shift change control.
TRGT PRES I/C (kPa, kg/cm
2 or psi)—— Displays the target oil pressure value of input
clutch solenoid valve calculated by the oil pres-
sure calculation process of shift change control.
TRGT PRES D/C (kPa, kg/cm
2 or psi)—— Displays the target oil pressure value of direct
clutch solenoid valve calculated by the oil pres-
sure calculation process of shift change control.
Monitored item (Unit)
Monitor Item Selection
Remarks
ECU IN-
PUT SIG- NALS MAIN SIG-
NALS SELEC-
TION
FROM ITEM
Revision: 2010 May2011 QX56

TM-64
< SYSTEM DESCRIPTION >[7AT: RE7R01B]
DIAGNOSIS SYSTEM (TCM)
TRG PRE 2346/B
(kPa, kg/cm2 or psi)—— Displays the target oil pressure value of 2346
brake solenoid valve calculated by the oil pres-
sure calculation process of shift change control.
SHIFT PATTERN — — Displays the gear change data using the shift
pattern control.
VEHICLE SPEED (km/h or mph) — — Displays the vehicle speed for control using the
control of TCM.
G SEN SLOPE (%) X — Displays the inclination angle calculated by the
G sensor signal received via CAN communica-
tion.
RANGE SW 4 (ON/OFF) X — Displays the operation status of transmission
range switch 4.
RANGE SW 3 (ON/OFF) X — Displays the operation status of transmission
range switch 3.
RANGE SW 2 (ON/OFF) X — Displays the operation status of transmission
range switch 2.
RANGE SW 1 (ON/OFF) X — Displays the operation status of transmission
range switch 1.
SFT DWN ST SW (ON/OFF) X —  Displays the operation status of paddle
shifter (down switch).
 Not mounted but displayed.
SFT UP ST SW (ON/OFF) X —  Displays the operation status of paddle
shifter (up switch).
 Not mounted but displayed.
DOWN SW LEVER (ON/OFF) X — Displays the operation status of selector lever
(down switch).
UP SW LEVER (ON/OFF) X — Displays the operation status of selector lever
(up switch).
NON M-MODE SW (ON/OFF) X — Displays whether the selector lever is in any po-
sition other than manual shift gate position.
MANU MODE SW (ON/OFF) X — Displays whether the selector lever is in the
manual shift gate position.
TOW MODE SW (ON/OFF) — — Displays the reception status of tow mode
switch signal received via CAN communication.
DS RANGE (ON/OFF) — —  Displays whether it is the DS mode.
 Not mounted but displayed.
1 POSITION SW (ON/OFF) X —  Displays the reception status of 1 position
switch signal received via CAN communica-
tion.
 Not mounted but displayed.
OD CONT SW (ON/OFF) X —  Displays the reception status of overdrive
control switch signal received via CAN com-
munication.
 Not mounted but displayed.
BRAKESW (ON/OFF) X — Displays the reception status of stop lamp
switch signal received via CAN communication.
POWERSHIFT SW (ON/OFF) X —  Displays the reception status of POWER
mode signal received via CAN communica-
tion.
 Not mounted but displayed.
Monitored item (Unit)
Monitor Item Selection
Remarks
ECU IN-
PUT SIG- NALS MAIN SIG-
NALS SELEC-
TION
FROM ITEM
Revision: 2010 May2011 QX56

DIAGNOSIS SYSTEM (TCM)TM-65
< SYSTEM DESCRIPTION > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
ASCD-OD CUT (ON/OFF) X — Displays the reception status of ASCD OD can-
cel request signal received via CAN communi-
cation.
ASCD-CRUISE (ON/OFF) X — Displays the reception status of ASCD opera-
tion signal received via CAN communication.
ABS SIGNAL (ON/OFF) X — Displays the re
ception status of ABS operation
signal received via CAN communication.
TCS GR/P KEEP (ON/OFF) X — Displays the reception status of TCS gear keep
request signal received via CAN communica-
tion.
TCS SIGNAL 2 (ON/OFF) X — Displays whether the reception value of A/T
shift schedule change demand signal received
via CAN communication is “cold”.
TCS SIGNAL 1 (ON/OFF) X — Displays whether the reception value of A/T
shift schedule change demand signal received
via CAN communication is “warm”.
LOW/B PARTS (FAIL/NOTFAIL) — — Displays whether the identified malfunction
point judged by TCM is the related parts of low
brake.
HC/IC/FRB PARTS (FAIL/NOTFAIL) — — Displays whether the identified malfunction
point judged by TCM is the related parts of high
and low reversed clutch, input clutch or front
brake.
IC/FRB PARTS (FAIL/NOTFAIL) — — Displays whether the identified malfunction
point judged by TCM is the related parts of input
clutch or front brake.
HLR/C PARTS (FAIL/NOTFAIL) — — Displays whether the identified malfunction
point judged by TCM is the related parts of high
and low reversed clutch.
W/O THL POS (ON/OFF) X — Displays the kickdown condition signal status
received via CAN communication.
CLSD THL POS (ON/OFF) X — Displays the idling status signal status received
via CAN communication.
DRV CST JUDGE (DRIVE/COAST) — — Displays the judgment results of “driving” or
“coasting” judged by TCM.
SHIFT IND SIGNAL — — Displays the transmission value of shift position
signal transmitted via CAN communication.
STARTER RELAY (ON/OFF) — — Displays the command status from TCM to
starter relay.
F-SAFE IND/L (ON/OFF) — — Displays the transmission status of A/T CHECK
indicator lamp signal transmitted via CAN com-
munication.
ATF WARN LAMP (ON/OFF) — — Displays the transmission status of ATF tem-
perature signal transmitted via CAN communi-
cation.
MANU MODE IND (ON/OFF) — — Displays the transmission status of manual
mode signal transmitted via CAN communica-
tion.
ON OFF SOL MON (ON/OFF) — — Monitors the command value from TCM to the
anti-interlock solenoid, and displays the moni-
tor status.
Monitored item (Unit)
Monitor Item Selection
Remarks
ECU IN-
PUT SIG- NALS MAIN SIG-
NALS SELEC-
TION
FROM ITEM
Revision: 2010 May2011 QX56

TM-66
< SYSTEM DESCRIPTION >[7AT: RE7R01B]
DIAGNOSIS SYSTEM (TCM)
DTC & SRT CONFIRMATION
START RLY MON (ON/OFF) — — Monitors the command value from TCM to the
starter relay, and displays the monitor status.
ON OFF SOL (ON/OFF) — — Displays the command status from TCM to anti-
interlock solenoid.
SLCT LVR POSI — X Displays the shift positions recognized by TCM.
GEAR — X Displays the current transmission gear position
recognized by TCM.
NEXT GR POSI — — Displays the target gear position of gear
change that is calculated based on the vehicle
speed information and throttle information.
SHIFT MODE — — Displays the transmission driving mode recog-
nized by TCM.
D/C PARTS (FAIL/NOTFAIL) — — Displays whether the identified malfunction
point judged by TCM is the related parts of di-
rect clutch.
FR/B PARTS (FAIL/NOTFAIL) — — Displays whether the identified malfunction
point judged by TCM is the related parts of front
brake.
2346/B PARTS (FAIL/NOTFAIL) — — Displays whether the identified malfunction
point judged by TCM is the related parts of 2346
brake.
2346B/DC PARTS (FAIL/NOTFAIL) — — Displays whether the identified malfunction
point judged by TCM is the related parts of 2346
brake or direct clutch.
N IDLE STATUS (ON/OFF) — — Displays the control status of idle neutral con-
trol.
Monitored item (Unit)
Monitor Item Selection
Remarks
ECU IN-
PUT SIG- NALS MAIN SIG-
NALS SELEC-
TION
FROM ITEM
Revision: 2010 May2011 QX56

TM-68
< ECU DIAGNOSIS INFORMATION >[7AT: RE7R01B]
TCM
ECU DIAGNOSIS INFORMATION
TCM
Reference ValueINFOID:0000000006226782
VALUES ON DIAGNOSIS TOOL
NOTE:
1. The CONSULT-III electrically displays shift timi
ng and lock-up timing (that is, operation timing of each
solenoid).
Check for time difference between actual shift timi ng and the CONSULT-III display. If the difference is
noticeable, mechanical parts (except solenoids, sens ors, etc.) may be malfunctioning. Check mechanical
parts in accordance with the specified diagnostic procedures.
2. Shift schedule (that implies gear position) on CONSULT-III may slightly differ from that is described in Ser-
vice Manual. This occurs because of the reasons as per the following:
- Actual shift schedule has more or less tolerance or allowance
- Shift schedule in Service Manual refers to the point where shifting starts
- Gear position on CONSULT-III indicates the point where shifting completes
3. Display of solenoid valves on CONSULT-III changes at t he start of shifting, while gear position is displayed
upon completion of shifting (which is computed by TCM).
CONSULT-III MONITOR ITEM
Item name Condition Value / Status (Approx.)
VHCL/S SE-A/T During driving Approximately equals the speed-
ometer reading.
ESTM VSP SIG During driving Approximately equals the speed-
ometer reading.
OUTPUT REV During driving (lock-up ON) Tachometer / Gear ratio
INPUT SPEED During driving (lock-up ON) Approximately equals the engine
speed.
F SUN GR REV During driving Revolution of front sun gear is indi-
cated.
F CARR GR REV During driving Revolution of front carrier is indi-
cated.
ENGINE SPEED Eng ine running Closely equals the tachometer
reading.
TC SLIP SPEED During driving Engine speed − Input speed
ACCELE POSI Accelerator pedal is released 0.0/8
Accelerator pedal is fully depressed 8.0/8
THROTTLE POSI Accelerator pedal is released 0.0/8
Accelerator pedal is fully depressed 8.0/8
ATF TEMP 1 Ignition switch ON Temperature of ATF in the oil pan is
indicated.
ATF TEMP 2 Ignition switch ON Temperature of ATF at the exit of
torque converter.
AT F T E M P S E 1 0 °C (32 ° F) – 20 °C (68 °F) – 80 °C (176 °F) 3.3 – 2.7 – 0.9 V
BATTERY VOLT Ignition switch ON Battery voltage (11 V – 14 V)
LINE PRES SOL During driving 0.2 – 0.6 A
TCC SOLENOID Slip lock-up is active 0.2 – 0.8 A
Lock-up is active 0.8 A
Other than the above 0 A
L/B SOLENOID Low brake is engaged 0.6 – 0.8 A
Low brake is disengaged 0 – 0.05 A
Revision: 2010 May2011 QX56

TCM
TM-73
< ECU DIAGNOSIS INFORMATION > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
*: Not mounted but always display as OFF.
TERMINAL LAYOUT
PHYSICAL VALUES
SLCT LVR POSI Selector lever in “N
” and “P” positions N/P
Selector lever in “R” position R
Selector lever in “D” and “DS” positions D
Selector lever in “M” position: 7GR
Selector lever in “M” position: 6GR 6
Selector lever in “M” position: 5GR 5
Selector lever in “M” position: 4GR 4
Selector lever in “M” position: 3GR 3
Selector lever in “M” position: 2GR 2
Selector lever in “M” position: 1GR 1
GEAR During driving 1st, 2nd, 3rd, 4th, 5th, 6th, 7th
NEXT GR POSI During driving 1st, 2nd, 3rd, 4th, 5th, 6th, 7th
SHIFT MODE Driving with the D position 0 or 3
Driving with the manual mode 4 or 8
D/C PARTS At 1GR - 2GR shift control FAIL
Other than the above NOTFAIL
FR/B PARTS At control fixed to 1GR FAIL
Other than the above NOTFAIL
2346/B PARTS At control fixed to 1GR FAIL
Other than the above NOTFAIL
2346B/DC PARTS At 2GR - 3GR - 4GR
shift control FAIL
Other than the above NOTFAIL
N IDLE STATUS Idle neutral is active ON
Other than the above OFF
Item name Condition Value / Status (Approx.)
SCIA1658E
Te r m i n a l
(Wire color) Description
Condition Value (Approx.)
+ −Signal name Input/
Output
1
(V) Ground Power supply Input Ignition switch ON Battery voltage
Ignition switch OFF 0 V
2
(P) Ground Power supply
(Memory back-up) Input Always Battery voltage
Revision: 2010 May2011 QX56

TCM
TM-77
< ECU DIAGNOSIS INFORMATION > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
1ST ENGINE BRAKE PROTECTION CONTROL
Controls the engine brake so as not to make effective by turning the front brake solenoid output to OFF when
each solenoid becomes the electricity pattern of 1st engine brake during driving at the vehicle speed 25 km/h
or more in any positions other than “R” position and 1GR.
TCM HIGH TEMPERATURE PROTECTION CONTROL
Limit the accelerator opening and forcibly control the vehi cle to the low torque driving when the electronic sub-
strate in TCM reaches the high temperature.
DTC Inspection Priority ChartINFOID:0000000006226785
If some DTCs are displayed at the same time, perfo rm inspections one by one based on the priority as per the
following list.
Malfunction detection condition Vehicle speed: 10 km/h (7 MPH) or more
Control at malfunction Neutral
Normal return condition  Vehicle speed: 8 km/h (5 MPH) or less
and
 Engine speed: 2,200 rpm or less
Vehicle behavior  The torque transmission cannot be performed
 There is a shock just before a vehicle stop
Malfunction detection condition Select lever and gear: Any position other than “R” position and 1GR
and
 Vehicle speed: More than 25 km/h (16 MPH)
Control at malfunction Front brake solenoid output signal; OFF
Normal return condition Other than detection condition of malfunction
Vehicle behavior Does not exist
Malfunction detection condition TCM electronic substrate temperature
145
°C (293 °F) and 120 seconds
or
150 °C (302 °F)
Control at malfunction Accelerator opening: 0.5/8 or less
Normal return condition  TCM electronic substrate temperature: Less than 140
°C (284 °F)
and
 Vehicle speed: 5 km/h (3 MPH) or less
Vehicle behavior Accelerator opening: output torque of approximately 0.5/8
Priority Detected items (DTC) Reference 1 U1000 CAN COMM CIRCUIT TM-103, "
DTC Logic"
Revision: 2010 May2011 QX56

TM-78
< ECU DIAGNOSIS INFORMATION >[7AT: RE7R01B]
TCM
DTC Index
INFOID:0000000006226786
NOTE:
 If some DTCs are displayed at the same time, per form inspections one by one based on the priority as per
the following list. Refer to TM-77, "
DTC Inspection Priority Chart".
 The IGN counter is indicated in Freeze frame data (FFD). Refer to TM-61, "
CONSULT-III Function (TRANS-
MISSION)".
2P0615 STARTER RELAY
TM-104, "
DTC Logic"
P0705 T/M RANGE SWITCH ATM-106, "DTC Logic"
P0710 FLUID TEMP SENSOR ATM-107, "DTC Logic"
P0717 INPUT SPEED SENSOR ATM-109, "DTC Logic"
P0720 OUTPUT SPEED SENSOR TM-110, "DTC Logic"
P0740 TORQUE CONVERTERTM-128, "DTC Logic"
P0745 PC SOLENOID ATM-131, "DTC Logic"
P0750 SHIFT SOLENOID ATM-132, "DTC Logic"
P0775 PC SOLENOID BTM-133, "DTC Logic"
P0795 PC SOLENOID CTM-136, "DTC Logic"
P2713 PC SOLENOID DTM-147, "DTC Logic"
P2722 PC SOLENOID ETM-148, "DTC Logic"
P2731 PC SOLENOID FTM-149, "DTC Logic"
P2807 PC SOLENOID GTM-150, "DTC Logic"
3P0729 6GR INCORRECT RATIO
TM-114, "
DTC Logic"
P0730 INCORRECT GR RATIOTM-116, "DTC Logic"
P0731 1GR INCORRECT RATIOTM-118, "DTC Logic"
P0732 2GR INCORRECT RATIOTM-120, "DTC Logic"
P0733 3GR INCORRECT RATIOTM-122, "DTC Logic"
P0734 4GR INCORRECT RATIOTM-124, "DTC Logic"
P0735 5GR INCORRECT RATIOTM-126, "DTC Logic"
P0744 TORQUE CONVERTERTM-129, "DTC Logic"
P0780 SHIFTTM-134, "DTC Logic"
P1730 INTERLOCKTM-140, "DTC Logic"
P1734 7GR INCORRECT RATIOTM-142, "DTC Logic"
4U0300 CAN COMM DATA
TM-102, "
DTC Logic"
P0725 ENGINE SPEED TM-112, "DTC Logic"
P1705 TP SENSORTM-137, "DTC Logic"
P1721 VEHICLE SPEED SIGNALTM-138, "DTC Logic"
P1815 M-MODE SWITCHTM-144, "DTC Logic"
Priority Detected items (DTC) Reference
DTC*1
Items
(CONSULT-III screen terms) Reference
MIL*2, “ENGINE” with
CONSULT-III or GST CONSULT-III only
“TRANSMISSION”
— P0615 STARTER RELAY TM-104
P0705 P0705 T/M RANGE SWITCH A TM-106
P0710 P0710 FLUID TEMP SENSOR ATM-107
P0717 P0717 INPUT SPEED SENSOR ATM-109
P0720 P0720 OUTPUT SPEED SENSOR TM-110
Revision: 2010 May2011 QX56

ADDITIONAL SERVICE WHEN REPLACING TRANSMISSION ASSEMBLY
TM-91
< BASIC INSPECTION > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
ADDITIONAL SERVICE WHEN REPL ACING TRANSMISSION ASSEMBLY
DescriptionINFOID:0000000006233270
Decel G sensor calibration must be performed when replacing A/T assembly.
Special Repair RequirementINFOID:0000000006233271
1.PREPARATION BEFORE CALIBRATION PROCEDURE
1. Park the vehicle on a flat road.
2. Adjust pressure in all tires to the specified value. Refer to WT-69, "
Tire Air Pressure".
>> GO TO 2.
2.PERFORM CALIBRATION
With CONSULT-III
1. Turn ignition switch ON.
CAUTION:
Never start the engine.
2. Select “G SENSOR CALIBRATION” in “Work Support” in “TRANSMISSION”.
3. Touch “START”. CAUTION:
Never give any motion to the vehicle during the calibration.
Is
“completed” displayed?
YES >> GO TO 3.
NO >> Perform the calibration again.
3.CHECK DTC
With CONSULT-III
1. Turn ignition switch OFF and wait 10 seconds or more.
2. Turn ignition switch ON.
3. Select “Self Diagnostic Results” in “ABS”.
Is
“C1145” or “C1146” detected?
YES >> Refer to BRC-51, "DTC Index".
NO >> Calibration end.
Revision: 2010 May2011 QX56

TM-92
< BASIC INSPECTION >[7AT: RE7R01B]
ADDITIONAL SERVICE WHEN RE
PLACING CONTROL VALVE & TCM
ADDITIONAL SERVICE WHEN REPLACING CONTROL VALVE & TCM
DescriptionINFOID:0000000006233274
Decel G sensor calibration must be performed when replacing control valve & TCM.
Special Repair RequirementINFOID:0000000006233275
1.PREPARATION BEFORE CALIBRATION PROCEDURE
1. Park the vehicle on a flat road.
2. Adjust pressure in all tires to the specified value. Refer to WT-69, "
Tire Air Pressure".
>> GO TO 2.
2.PERFORM CALIBRATION
With CONSULT-III
1. Turn ignition switch ON.
CAUTION:
Never start the engine.
2. Select “G SENSOR CALIBRATION” in “Work Support” in “TRANSMISSION”.
3. Touch “START”. CAUTION:
Never give any motion to the vehicle during the calibration.
Is
“completed” displayed?
YES >> GO TO 3.
NO >> Perform the calibration again.
3.CHECK DTC
With CONSULT-III
1. Turn ignition switch OFF and wait 10 seconds or more.
2. Turn ignition switch ON.
3. Select “Self Diagnostic Results” in “ABS”.
Is
“C1145” or “C1146” detected?
YES >> Refer to BRC-51, "DTC Index".
NO >> Calibration end.
Revision: 2010 May2011 QX56