ECO mode INFINITI QX60 2015 Quick Reference Guide

8
essential information
Tire Pressure Monitoring System (TPMS) with Tire Inflation Indicator
A Tire Pressure Low – Add Air warning message
will appear in the vehicle information display

1
and the low tire pressure warning light 2 will
illuminate when one or more tires are low in
pressure and air is needed.
• The tire pressures should be checked when the
tires are cold. The tires are considered cold after
the vehicle has been parked for 3 hours or more
or driven less than 1 mi (1.6 km) at
moderate speeds.

When adding air to an under-inflated tire, the TPMS
with Tire Inflation Indicator provides visual and
audible signals to help you inflate the tire to the
recommended COLD tire pressure.
To use the tire inflation indicator:
1. Move the shift lever to the P (PARK) position and apply the parking brake.
2. Place the ignition switch in the ON position. Do not start the engine.
3. Add air to the under-inflated tire, and within a few seconds, the hazard\
warning lights will
start flashing.
4. When the designated tire pressure is reached, the horn will beep once an\
d the hazard
warning flashers will stop flashing.
5. Repeat this procedure for any additional under-inflated tires.

After tire pressures are adjusted, drive the vehicle at speeds above 16 \
mph (25 km/h).
The Tire Pressure Low – Add Air warning message and low tire pressure warning light
will extinguish.

When the low tire pressure warning light flashes for approximately 1 min\
ute and then
remains on, the TPMS is not functioning properly. Have the system checke\
d by an
INFINITI retailer.

Tire pressure rises and falls depending on the heat caused by the vehicl\
e’s operation and
the outside temperature. Low outside temperature can lower the temperatu\
re of the air
inside the tire, which can cause a lower tire inflation pressure. This m\
ay cause the low
tire pressure warning light to illuminate. If the warning light illumina\
tes, check the tire
pressure in your tires.
• Check the tire pressure (including the spare tire) often and always pr\
ior to long
distance trips.

The Tire and Loading Information label contains valuable information. Re\
fer to the
“Technical and consumer information (section 9)” in your Owner’\
s Manual for the location
of the Tire and Loading Information label.
For more information, refer to the “Instruments and controls (section 2)”, the “Starting and driving (section 5)” and the
“Maintenance and do-it-yourself (section 8)” of your Owner’s Manual.
1
2
1923535_15c_Infiniti_QX60_QRG_061815.indd 86/18/15 2:16 PM

9
Accessing the Front Cup Holders
To open the cup holders, push the lid 1 down
and release.
For more information, refer to the “Instruments and controls (section 2)”
of your Owner’s Manual.1
Loose Fuel Cap
A LOOSE FUEL CAP warning message will appear in
the vehicle information display

1 when the
fuel-filler cap is not tightened correctly.

To tighten, turn the cap clockwise until a single click
is heard.

The warning message will extinguish when the vehicle
detects the fuel-filler cap is properly tightened and the
reset button
2 is pressed for about 1 second.

If the cap is not properly tightened, the Malfunction
Indicator Light

may illuminate.
For more information, refer to the “Instruments and controls (section 2)”
and the “Pre-driving checks and adjustments (section 3)” of your
Owner’s Manual.
1
2
Fuel-filler Door
The fuel-filler door is located on the driver’s side of

the vehicle.

The fuel-filler door automatically locks or unlocks
when the driver’s door is locked or unlocked.

To open the fuel-filler door, push the right side of the
fuel-filler door and release.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
Towing Your Vehicle
All-Wheel Drive (AWD) Vehicle:
•
An all-wheel drive vehicle must be towed with all wheels off the ground \
even if the
vehicle is placed in the 2WD mode.

For proper towing and to avoid accidental damage to your vehicle, INFINI\
TI
recommends that a service operator tow your vehicle after carefully read\
ing the Owner’s
Manual precautions.
For more information, refer to the “In case of emergency (section 6)” of your Owner’s Manual.
1923535_15c_Infiniti_QX60_QRG_061815.indd 96/18/15 2:16 PM

11
first drive features
INFINITI Intelligent Key System
The INFINITI Intelligent Key system allows you to lock or unlock your
vehicle, open your liftgate and remotely start the engine. It is importa\
nt to
make sure the Intelligent Key is with you (that is, in your pocket or p\
urse).
REMOTE ENGINE START* (if so equipped)

The remote engine start system must be enabled in the vehicle
settings within the vehicle information display.

The remote engine start operating range is approximately 200 ft
(60 m) from the vehicle. The effective operating range may be
shorter due to environmental conditions or obstacles between you
and the vehicle.

For the remote engine start to function, the vehicle must be in
the P (PARK) position with the ignition off and all the doors
closed and locked.

To start your vehicle remotely:
1. Press the

button
1.
2. Within 5 seconds, press and hold the remote engine start

button
2
for at least 2 seconds.

The engine will start, and the parking lights will turn on.

Automatic climate control will begin heating or cooling the vehicle depe\
nding on the last
used mode.

The engine will run for 10 minutes and then turn off.

Repeat steps 1 and 2 to extend the time for an additional 10-minute peri\
od.
• After two remote starts, the ignition switch must be cycled before the r\
emote start can be
used again.

To start driving, depress the brake pedal and push the ignition switch START/STOP button.
LOCKING AND UNLOCKING THE VEHICLE

The lock and unlock operating range of the
Intelligent Key is within 31.5 in (80 cm) from
each request switch.

To lock the vehicle, push either door handle
request switch

3 once or press the
button
1
on the key fob.

To unlock the vehicle, perform one of the following procedures:
• Push either door handle request switch

3 once; the corresponding door will unlock.
Push the door handle request switch 3 again within 30 seconds; all other doors
will unlock, or
• Press the

button
4 on the key fob to unlock the driver’s side door. Press the
button 4 again; all other doors will unlock.
*Laws in some communities may restrict the use of remote starters. Check\
local regulations before using this feature.
2
1
4
5
6
3
1923535_15c_Infiniti_QX60_QRG_061815.indd 116/18/15 2:16 PM

19
Rear Climate Controls
To activate the system:
1. Turn on the front climate control system by
pressing the AUTO button
1.
2. Press the REAR button

2 on the front control
panel until the Rear Air-conditioning screen
is displayed.
• The indicator light will illuminate.
8 DEFROSTING/DEFOGGING FRONT AND SIDE WINDOWS

Press the defroster button
to turn the system on. The A/C automatically turns on
when the defroster mode is selected. This feature removes humidity from \
the air.

To defrost the front and side windows, set the temperature controls
3 and fan speed
controls 7 to their maximum settings.
9
DEFROSTING REAR WINDOW AND OUTSIDE MIRRORS

Push the rear window defroster button
to turn the system on or off.
This function automatically turns off after approximately 15 minutes.
10 REAR AIR CONDITIONER
To control the rear automatic air conditioning
system with the front air conditioner control panel:
1. Turn on the front climate control system by
pressing the AUTO button
1.
2. Press the REAR button.

When the rear automatic air conditioning system
is on, the indicator light on the REAR button will
illuminate and the front display will switch to the Rear Air-conditioning screen. Use the
driver’s temperature and fan speed buttons to adjust the settings.

To adjust the front air conditioning system, press the REAR button again.

To turn off the rear automatic air conditioning system from the front co\
ntrols, press
the REAR button until the Rear Air-conditioning screen is displayed. Then press the
OFF button.

The rear control buttons will not function when the Rear Air-conditioning screen is
shown on the front display.
11 AIR RECIRCULATION BUTTON

Press the intake air control button to recirculate interior air inside the vehicle. The indicator light on the button will illuminate. This system is used to a\
void certain
outside odors and to help adjust the inside vehicle temperature more eff\
ectively.

The air recirculation mode cannot be activated when the climate control \
system is in the
front defroster mode

.

Press the intake air control button again to change the air circulation from the
intake air to the outside air. The
indicator light on the button will turn off.
12 OFF BUTTON
Press the OFF button to turn the climate control system off.
For more information, refer to the “Monitor, climate, audio, phone and voice recognition systems (secti\
on 4)” of your
Owner’s Manual.
21
1923535_15c_Infiniti_QX60_QRG_061815.indd 196/18/15 2:16 PM

22
first drive features
Intelligent Cruise Control (ICC) System (if so equipped)
VEHICLE-TO-VEHICLE DISTANCE CONTROL MODE

To set Vehicle-To-Vehicle Distance Control mode,
press the CRUISE ON/OFF button
1 for less than
1.5 seconds. The CRUISE indicator light 2
will illuminate.

Accelerate to the desired speed.

Push down on the COAST/SET switch
3 and

release it. Intelligent Cruise Control will be set to
the desired speed.

Press the distance button 4 repeatedly to change
the set distance between long, middle and short.

When a vehicle is not detected ahead of you in
the lane, the set distance and set vehicle speed
indicator lights will illuminate

5 in set mode.

When a vehicle is detected ahead of you in the lane,
the vehicle ahead detection, set distance and set
vehicle speed indicator lights will illuminate
6 in set mode.

To reset at a faster cruising speed, push and hold the ACCEL/RES
switch

7. When the vehicle attains the desired speed, release the switch.

To reset at a slower cruising speed, push and hold the COAST/SET switch
3.
Release the switch when the vehicle slows to the desired speed.

To cancel the preset speed, push the CANCEL switch
8 or tap the brake pedal. The set
vehicle speed indicator
5 will extinguish.
To turn off Intelligent Cruise Control, press the CRUISE ON/OFF button
1. The CRUISE
indicator light
2 in the instrument panel will extinguish.
To set conventional (fixed speed) cruise control mode:

While Intelligent Cruise Control is off, press the CRUISE ON/OFF
button 1
and hold it
down for more than 1.5 seconds. The CRUISE indicator light will illuminate.

Accelerate to the desired speed.

Push down on the COAST/SET switch and release it. The SET indicator light will illuminate.
Cruise control will be set to the desired speed.
To switch between the two cruise control modes:

When one of the two cruise modes is in use, you must turn the system off\
, and then turn it
on again to select the other cruise control mode.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
1
43
78
25
6
To cancel the preset speed, push the CANCEL switch
4.

To turn off cruise control, push the CRUISE
ON/OFF switch
1. Both the
CRUISE indicator
light
and the SET indicator light in the instrument panel will extinguish.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
1923535_15c_Infiniti_QX60_QRG_061815.indd 226/18/15 2:17 PM

24 SETTINGS
The setting mode allows you to change the information displayed in the ve\
hicle
information display:

Driver Assistance (if so equipped)

Main Menu Selection

Body Color

Maintenance

Alarms

Vehicle Settings

Language

Unit

Welcome Effects
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
Vehicle Information Display
The vehicle information display
1 displays items
such as:

Vehicle settings

Trip computer information

Drive system warnings and settings (if so equipped)

Cruise control system

Intelligent Cruise Control (ICC) system
(if so equipped) information

Intelligent Key operation information

Indicators and warnings

Tire pressure information
USING THE VEHICLE INFORMATION DISPLAY
The vehicle information display modes can be changed
using the
button
2 and ENTER button 3
located
on the steering wheel.
1. Press the
button 2 to enter the vehicle
information menu items.
2. Press the
button 4 to navigate through the items in the vehicle information.
3. Press the ENTER button 3 to change or select an item in the vehicle information display.
4. Press the button 5 to go back to the previous menu.
START UP DISPLAY
When the vehicle is placed in the ON or ACC position, the screens that display in the vehicle
information include:

Active system status (if so equipped)
Trip computer

Tire pressure information
Fuel economy

Warnings (displays when a warning is present)
RESETTING THE TRIP COMPUTER
1. Press the
button
2 until you reach the trip
computer mode 6.
2. Press the
button 2 again for more than
1.5 seconds to reset average fuel consumption,
average speed, distance to empty and journey time.
1
system guide
3
2
4
5
6
1923535_15c_Infiniti_QX60_QRG_061815.indd 246/18/15 2:17 PM

26 FOR DEVICES OTHER THAN PHONES
1. Press the SETTING button on the instrument panel
and select the “Bluetooth” key on the display.
2. Select the “Connect Bluetooth” key.
3. A pop-up box will appear on the screen, prompting
you to confirm that the connection is for the phone
system. Touch the “No” key.
4. This will bring up the PIN pad on the screen. Enter a
unique 4-digit PIN into the pad and touch OK.
• When prompted for a PIN on the device, enter the
unique 4-digit PIN that was entered on the screen.
• The connecting procedure varies according to each
device model. For detailed connecting instructions
and a list of compatible devices, please visit
www.InfinitiUSA.com/bluetooth.
5. Verify that the system confirms your device has
been added and then select it as an audio player.
6. Select “Connected Devices” in the Settings Menu.
7. Select “Audio Player”.
8. Select the name of the device that you are
attempting to connect as an audio player.
9. Select “Select”.
10. Verify that the system confirms that your device has
been selected as an audio player.
For more information, refer to the “Monitor, climate, audio, phone and voice
recognition systems (section 4)” of your Owner’s Manual or please visit www.InfinitiUSA.com/bluetooth.
system guide
1923535_15c_Infiniti_QX60_QRG_061815.indd 266/18/15 2:17 PM

27
Bluetooth® Hands-free Phone System
A cellular telephone should not be used while driving
so full attention may be given to vehicle operation.*
SYSTEM OPERATING TIPS

Press the or button to interrupt the voice
prompts at any time and speak a command after
the tone.

For vehicles not equipped with Navigation:
• To use the system faster, you may speak the second
level commands with the main menu command on
the main menu. For example, press the
or
button, and after the tone, say “Call Redial”.

For vehicles equipped with Navigation:
• This system has an “Alternate Command Mode”
setting that allows the total number and length of
prompts to be reduced. When the “Alternate
Command Mode” is activated, you may speak
second level commands with the main menu
command. For example, press the
or
button, and after the tone, say “Call” followed by a
stored name.

The “Help” command can be used to hear a list of available command\
s at any time.

Reduce background noise as much as possible by closing windows and point\
ing HVAC
vents away from the ceiling.

Speak naturally without long pauses and without raising your voice.

When speaking phonebook names, please be aware some phones require the l\
ast name
to be spoken before the first name. For example, “Michael Smith” m\
ay be spoken as
“Smith Michael”.

To cancel a Voice Recognition session, say “Cancel” or “Quit”\
or press and hold the
or

button for 5 seconds.

To go back to the previous command, say “Go back” or “Correctio\
n”.

If the Voice Recognition system does not recognize your voice commands, \
train the system
using the Speaker Adaptation Mode. See your Owner’s Manual for detail\
ed information.

For more detailed information and instructions, refer to your cellular p\
hone’s Owner’s
Manual and visit www.InfinitiUSA.com/bluetooth.
*Some jurisdictions prohibit the use of cellular telephones while drivin\
g.
Bluetooth® Controls
Microphone
1923535_15c_Infiniti_QX60_QRG_061815.indd 276/18/15 2:17 PM

34
system guide
Theater Package (if so equipped)
With this Entertainment System, you can play video
files via a DVD, USB or CD, providing images and
sound both from the front and rear display screens.

You can also connect auxiliary devices, such as
video games, camcorders or portable video players,
to the auxiliary jacks
1 located on the back of the
center console. (Your device will be controlled
through its own control panel.)

Rear Auxiliary Mode allows rear seat passengers
to independently display different sources on
each screen.

Use the remote controller
2 provided with the
system to operate the rear display screens.

The rear displays can be activated or deactivated
individually by the remote controller.
• To activate or deactivate the rear displays, select
the preferred side (L or R) and press the
POWER
button on the remote controller.

The rear displays can be activated or deactivated
individually from the front seats by using the
front display.
• To activate or deactivate the rear displays, press
the SETTING button then press the Rear Display
key on the front display. Press Display Control key
and select ON or OFF for the preferred side.

Use the headphones
3, also provided with
the system, to listen to audio wirelessly and
independently. You may also connect your own
wired-headphones to the headphone jacks
4
located on the back of the center console.

For optimum performance, select the appropriate
headphone channel

5 that corresponds to the
headrest display being viewed directly in front of you.

To watch or control videos on the front display, make sure the
vehicle is in the P (PARK) position and the parking brake is applied.

To reduce driver distraction, the wireless headphones will not
operate while located in the front seats and movies will not be
shown on the front display while the vehicle is in any drive position.

To access standard DVD controls on the front display while playing
a DVD on the rear display, press the DISC•AUX button on the audio
control panel while the vehicle is in the P (PARK) position and the parking brake is applied.
For more information, refer to the “Monitor, climate, audio, phone and voice recognition systems (sect\
ion 4)” of
your Owner’s Manual.
5
4
1
2
3
1923535_15c_Infiniti_QX60_QRG_061815.indd 346/18/15 2:17 PM