key fob INFINITI QX60 2016 Quick Reference Guide

10
first drive features
Infiniti Intelligent Key System
The Infiniti Intelligent Key system allows you to lock or
unlock your vehicle, open your liftgate and remotely start
the engine. It is important to make sure the Intelligent Key
is with you (that is, in your pocket or purse).
LOCKING AND UNLOCKING YOUR VEHICLE
The operating range of the Intelligent Key is within
31.5 in (80 cm) from each request switch.
To lock the vehicle, push either door handle request switch 1 once
or press the
button 2 on the key fob.
To unlock the vehicle, perform one of the following procedures:
•


Push either door handle request switch 1 once; the
corresponding door will unlock. Push the door handle request
switch
1 again within 1 minute; all other doors will unlock, or
• Press the button 3 on the key fob to unlock the driver’s side
door. Press the
button 3 again; all other doors will unlock.
REMOTE ENGINE START* (if so equipped)
The remote engine start system must be enabled in the vehicle
settings within the vehicle information display.
The remote engine start operating range is approximately 200 ft (60 m)\
from the vehicle.
The effective operating range may be shorter due to environmental condit\
ions or obstacles
between you and the vehicle.
For the remote engine start to function, the vehicle must be in the P (PARK) position with
the ignition off and all the doors closed and locked.
To start your vehicle remotely:
1. Press the button 2.
2.


Within 5 seconds, press and hold the remote engine start button 6
for at least 2 seconds.
The engine will start, and the parking lights will turn on.
Automatic climate control will begin heating or cooling the vehicle depe\
nding on the last
used mode.
The engine will run for 10 minutes and then turn off.
Repeat steps 1 and 2 to extend the time for an additional 10-minute peri\
od.
• After two remote starts, the ignition switch must be cycled before the r\
emote start can be
used again.
To start driving, depress the brake pedal and press the ignition switch \
START/STOP button.
*Laws in some communities may restrict the use of remote starters. Check\
local regulations before using this feature.
6
2
3
4
5
1
2460934_16b_Infiniti_QX60_QRG_031716_b.indd 103/17/16 2:17 PM

14
Automatic Drive Positioner (if so equipped)
Two positions for the driver’s seat, steering column
and outside mirrors can be stored in the automatic
drive positioner
1 memory.
Follow this procedure to set the memory positions:
• Push the ignition switch to the ON or ACC position.
(The vehicle should be stopped while setting
the memory.)
• Adjust the driver’s seat, steering column and
outside mirrors to the desired positions using the
adjusting switches for each feature.
• Push the SET
switch, and within 5 seconds push the memory switch (1 or 2).
• The indicator light for the memory switch you select will illuminate for\
approximately 5
seconds and a chime will sound when the memory is stored.
• The driver’s seat, steering column and outside mirror positions are n\
ow set to
your preferences.
These memorized positions can also be linked to your Infiniti Intelligen\
t Key.
To link a memorized position to your Infiniti Intelligent Key, press the\
unlock button on the
key fob after completing the previous step.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
Outside Mirror Control Switch
To select the right or left side mirror, move the control switch 1 right or left.
Adjust each mirror to the desired position using the control switch 2.
To fold the outside rearview mirrors, push the control switch 3 to the position. To
unfold the outside rearview mirrors, push the control switch 3 to the position.
REVERSE TILT-DOWN FEATURE (if so equipped)
The reverse tilt-down feature will turn both outside
mirror surfaces downward to provide better rear
visibility close to the vehicle.
1. Apply the brake.
2. Push the ignition switch to the ON position.
3.


Move the shift lever to the R (REVERSE)
position.
4.


The outside mirror surfaces will move downward.
(The mirror control switch 1 must be out of the
center [neutral] position.)
The outside mirror surfaces will return to their original positions when\
one of the following
conditions has occurred:
• The shift lever is moved to any position other than R (REVERSE)

.
• The outside mirror control switch 1 is set to the center (neutral) position.
• The ignition switch is placed in the OFF position.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
21
3
1
first drive features
2460934_16b_Infiniti_QX60_QRG_031716_b.indd 143/17/16 2:19 PM