lock INFINITI QX60 2018 Manual PDF

CAUTION
For vehicles with automatic drive posi-
tioner: Failure to reset the tilt and telescop-
ing functions of the steering wheel, after
the vehicle’s battery has been discharged,
may prevent the steering wheel position
from being adjusted.
For vehicles with automatic drive positioner:
Both the tilt and telescopic steering opera-
tion must be reset after the vehicle’s battery
has been discharged in order to prevent the
tilt and telescopic operation from locking in
one position. When the battery has been re-
charged or replaced, perform the following: ∙ For tilt operation: Adjust the switch
1so
the steering wheel moves to the highest
position
2that can be reached.
∙ For telescopic operation: Adjust the switch
1so the steering wheel moves to
the most forward and backward position
3that can be reached.
Performing these operations resets the range
of the steering wheel’s tilt and telescopic
function.
Entry/Exit function
The automatic drive positioner system will
make the steering wheel move up automati-
cally when the driver’s door is opened and the
ignition switch is in the LOCK position. This
lets the driver get into and out of the seat
more easily. The steering wheel moves back
into position when the driver’s door is closed
and the ignition switch is pushed.
For additional information, refer to “Auto-
matic drive positioner” in this section.
1. To block glare from the front, swingdown the sun visor
1.
2. To block glare from the side, remove the sun visor from the center mount and
swing the visor to the side
2.
WPD0435
SUN VISORS
3-32Pre-driving checks and adjustments

SETTING MEMORY FUNCTION
The position of the following settings can be
linked to the Intelligent Key and the memo-
rized settings can be available for each Intel-
ligent Key.∙ Climate control system
∙ Navigation system (if so equipped)
∙ Audio system
To use the memory function, set the climate,
navigation and audio systems to the driver’s
preferred settings. Lock the doors with the
Intelligent Key. Each Intelligent Key may be
set with the driver’s individual preferences.
When a new Intelligent Key is used, “Connec-
tion with the key has been done” will be dis-
played on the vehicle information display and
the memorized settings are available.
To engage the memorized settings, perform
the following: 1. Carry the Intelligent Key that is linked to the memorized settings.
2. Unlock the doors by pushing the driver’s door handle request switch or the
button on the Intelligent Key. 3. Place the ignition switch in the ON posi-
tion. The settings linked to the Intelligent
Key will start.
For additional information on using the Cli-
mate control system, refer to “Heater and air
conditioner (automatic)” in the “Monitor, cli-
mate, audio, phone and voice recognition
systems” section of this manual.
For additional information, refer to the
INFINITI InTouch™ Owner’s Manual or the
“Monitor, climate, audio, phone and voice
recognition systems” section of this manual.
SYSTEM OPERATION
The automatic drive positioner system will
not work or will stop operating under the
following conditions: ∙ When the vehicle speed is above 0 mph (0 km/h) or 4 mph (7km/h) for some
limited functions such as linking a key fob
to the meter when the power source is
turned on from off or during the exit
function.
∙ When any of the memory switches are pushed while the automatic drive posi-
tioner is operating. ∙ When the adjusting switch for the driver’s
seat and steering column is turned on
while the automatic drive positioner is
operating.
∙ When the seat has already been moved to the memorized position.
∙ When no seat position is stored in the memory switch.
∙ When the shift lever is moved from P (Park) to any other position.
Pre-driving checks and adjustments3-39

when backing up to the positionAif the
object projects over the actual backing up
course.
HOW TO PARK WITH
PREDICTED COURSE LINES
WARNING
∙ If the tires are replaced with different sized tires, the predicted course lines may
be displayed incorrectly.
∙ On a snow-covered or slippery road, there may be a difference between the
predicted course line and the actual
course line.
∙ If the battery is disconnected or becomes discharged, the predicted course lines
may be displayed incorrectly. If this oc-
curs, please perform the following
procedures:
– Turn the steering wheel from lock to lock while the engine is running.
– Drive the vehicle on a straight road for more than 5 minutes.
∙ When the steering wheel is turned with the ignition switch in the ACC position,
the predicted course lines may be dis-
played incorrectly. 1. Visually check that the parking space is
safe before parking your vehicle.
2. The rear view of the vehicle is displayed on the screen
Awhen the shift lever is
moved to the R (Reverse) position. 3. Slowly back up the vehicle adjusting the
steering wheel so that the predicted
course lines
Benter the parking space
C.
4. Maneuver the steering wheel to make the vehicle width guide lines
Dparallel
LHA1197LHA1198
4-10Monitor, climate, audio, phone and voice recognition systems

Example of slot parking (right side)
Stop the vehicle at approximately1mtothe
side of the target and begin the parking pro-
cedure.1. Press the CAMERA button to display the bird’s-eye view.
2. Select “Park Guide”.
3. Select “Backward (R)”. 4. The parking position adjustment screen
will be displayed, showing the clearance
guidelines in red1and the target park-
ing frame in blue
2.
5. Adjust the target parking frame (blue) so that the clearance guidelines (red) do not
overlap with obstacles and set the park-
ing position. Use the up, down, left and
right keys on the screen
3to move the
target parking frame (blue). Use the
clockwise and counterclockwise keys on
the screen
4to rotate the target park-
ing frame (blue). Select “Start”. 6. The starting position frame for backing
up will be displayed in green
1. The
starting position frame is displayed in the
bird’s-eye view and front view.
∙ A green frame indicates the recom- mended position.
∙ A yellow frame indicates that switch- ing will be required.
∙ A red frame indicates that parking is not possible.
LHA4330LHA4331LHA4332
4-14Monitor, climate, audio, phone and voice recognition systems

11. Keep the steering wheel in its currentposition and move the vehicle slowly
backward toward the orange frame. A
chime will sound when the vehicle fits
into the frame. You can adjust the target
parking frame by turning the steering
wheel left or right during backing up.
12. Align the steering wheel and move the vehicle slowly backward toward the tar-
get parking frame.
13. Stop the vehicle.Example of parallel parking
(left side)
Stop the vehicle at approximately1mtothe
side of the target parking position and begin
the parking procedure. 1. Press the CAMERA button to display the bird’s-eye view.
2. Select “Park Guide”.
3. Select "Parallel (L)”. 4. The parking position adjustment screen
will be displayed, showing the clearance
guidelines in red1and the target park-
ing frame in blue
2.
5. Adjust the target parking frame (blue) so that the clearance guidelines (red) do not
overlap with obstacles and set the park-
ing position. Use the up, down, left and
right keys on the screen
3to move the
target parking frame (blue). Use the
clockwise and counterclockwise keys on
the screen
4to rotate the target park-
ing frame (blue).
LHA4335LHA4330LHA4336
4-16Monitor, climate, audio, phone and voice recognition systems

∙ If your vehicle sustains damage to theparts where the camera is installed, leav-
ing it misaligned or bent, the sensing zone
may be altered and the MOD system may
not detect objects properly.
∙ When the temperature is extremely high or low, the screen may not display objects
clearly. This is not a malfunction.
NOTE:
The blue MOD icon will change to orange if
one of the following has occurred: ∙ When the system is malfunctioning.
∙ When the component temperature reaches a high level (icon will blink).
∙ When the Rear View camera has de- tected a blockage (icon will blink).
If the icon light continues to illuminate or-
ange, have the MOD system checked. It is
recommended that you visit an INFINITI re-
tailer for this service.
SYSTEM MAINTENANCE
CAUTION
∙ Do not use alcohol, benzine or thinner to clean the camera. This will cause
discoloration.
∙ Do not damage the camera as the moni- tor screen may be adversely affected.
If dirt, rain or snow accumulates on any of the
cameras
1, the MOD system may not oper-
ate properly. Clean the camera by wiping
with a cloth dampened with a diluted mild
cleaning agent and then wiping with a dry
cloth.
LHA4347
Monitor, climate, audio, phone and voice recognition systems4-31

System maintenance....................... 5-110
Forward Emergency Braking (FEB) with
Pedestrian Detection system (if so equipped) . . . 5-112 System operation .......................... 5-113
Turning the FEB with Pedestrian
Detection system on/off ...................5-115
FEB with Pedestrian Detection system
limitations ................................. 5-116
System temporarily unavailable .............5-118
System malfunction ........................ 5-119
System maintenance ....................... 5-119
Predictive Forward Collision Warning (PFCW)
(if so equipped) ................................ 5-121
PFCW system operation ...................5-123
Turning the PFCW system on/off ..........5-124
PFCW system limitations ...................5-126
System temporarily unavailable .............5-130
System malfunction ........................ 5-131
System maintenance ....................... 5-131
Break-in schedule ............................. 5-132
Increasing fuel economy .......................5-133
Intelligent All-Wheel Drive (AWD)
(if so equipped) ................................ 5-133
Parking/parking on hills .......................5-136Towing a trailer
............................... 5-137
Flat towing ................................ 5-137
Towing load/specification
(Gulf Standard models) .....................5-138
Towing load/specification
(all except Gulf Standard models) ...........5-138
Electric trailer brake controller
(if so equipped) ............................. 5-138
Power steering ................................ 5-140
Brake system ................................. 5-141
Brake precautions .......................... 5-141
Anti-lock Braking System (ABS) .............5-141
Brake assist ................................ 5-142
Vehicle Dynamic Control (VDC) system .........5-143
Active Trace Control (if so equipped) ........5-144
Brake force distribution .....................5-145
Hill

start assist system ......................... 5-146
Front and rear sonar system ...................5-146
System operation .......................... 5-147
How to enable/disable the sonar system ....5-149
Sonar limitations ........................... 5-150
System temporarily unavailable .............5-150
System maintenance ....................... 5-150
Cold weather driving .......................... 5-151

Freeing a frozen door lock..................5-151
Antifreeze ................................. 5-151
Battery .................................... 5-151
Draining of coolant water ..................5-151Tire equipment
............................. 5-151
Special winter equipment ...................5-152
Driving on snow or ice ...................... 5-152

∙ Do not attempt to test an AWD equippedvehicle on a 2-wheel dynamometer (such
as the dynamometers used by some
states for emissions testing), or similar
equipment even if the other two wheels
are raised off the ground. Make sure you
inform test facility personnel that your
vehicle is equipped with AWD before it is
placed on a dynamometer. Using the
wrong test equipment may result in
drivetrain damage or unexpected vehicle
movement which could result in serious
vehicle damage or personal injury.
∙ When a wheel is off the ground due to an unlevel surface, do not spin the wheel
excessively.WARNING
Do not operate the push-button ignition
switch while driving the vehicle except in an
emergency. (The engine will stop when the
ignition switch is pushed three consecutive
times in quick succession or the ignition
switch is pushed and held for more than
2 seconds.) If the engine stops while the
vehicle is being driven, this could lead to a
crash and serious injury.
When the ignition switch is pushed without
depressing the brake pedal, the ignition
switch will illuminate.
Push the ignition switch center:∙ Once to change to ACC.
∙ Two times to change to ON.
∙ Three times to return to OFF.
The ignition switch will automatically return
to the LOCK position when any door is either
opened or closed with the switch in the OFF
position.
LSD2014
PUSH-BUTTON IGNITION SWITCH
Starting and driving5-13

The ignition lock is designed so that the igni-
tion switch position cannot be switched to
OFF until the shift lever is moved to the P
(Park) position.
When the ignition switch cannot be pushed
toward the OFF position, proceed as follows:1. Move the shift lever to the P (Park) posi- tion.
2. Push the ignition switch. The ignition switch position will change to the ON
position.
3. Push the ignition switch again to the OFF position.
The shift lever can be moved from the P
(Park) position if the ignition switch is in the
ON position and the brake pedal is de-
pressed.
If the battery of the vehicle is discharged, the
push-button ignition switch cannot be
moved from the LOCK position.
Some indicators and warnings for operation
are displayed on the vehicle information dis-
play. For additional information, refer to “Ve-
hicle information display” in the “Instruments
and controls” section of this manual.
OPERATING RANGE
The Intelligent Key functions can only be used
when the Intelligent Key is within the speci-
fied operating range.
When the Intelligent Key battery is almost
discharged or strong radio waves are present
near the operating location, the Intelligent
Key system’s operating range becomes nar-
rower and may not function properly.
If the Intelligent Key is within the operating
range, it is possible for anyone, even some-
one who does not carry the Intelligent Key, to
push the ignition switch to start the engine. The operating range of the engine start func-
tion is inside of the vehicle
1.
∙ The luggage area is not included in the operating range, but the Intelligent Key
may function.
∙ If the Intelligent Key is placed on the in- strument panel, inside the glove box,
storage bin or door pocket, the Intelligent
Key may not function.
∙ If the Intelligent Key is placed near the door or window outside the vehicle, the
Intelligent Key may function.
PUSH-BUTTON IGNITION
SWITCH POSITIONS
LOCK (Normal parking position)
The ignition switch can only be locked in this
position.
The ignition switch will be unlocked when it is
pushed to the ACC position while carrying
the Intelligent Key.
The ignition switch will lock when any door is
opened or closed with the ignition switched
off.
LSD2020
5-14Starting and driving